AMW-500 - American Weigh Scales
Contents
1. PASS 6 Remove the weight and press ON OFF to turn off the scale Finished Repeat if needed Calibration Procedures for AMW 50 1 Turn OFF the scale 2 Press ON OFF shortly Then immediately press and hold MODE until CAL is displayed Release the MODE key 3 Press MODE again Now the display will show CAL and 50 00 will flash 3 times 4 Place a 50g weight on the center of platform Wait 3 4 seconds The LCD display will read PASS then 50 00 5 Remove the weight and press ON OFF to turn off the scale Finished Repeat if needed Calibration Procedures for AMW 100 1 Turn on the scale by pressing ON OFF key 2 Wait until the LCD displays 0 00 and then press and HOLD the MODE key for 3 seconds the LCD will display CAL then release the MODE key 3 Press the MODE key again the LCD will display CAL and then 100 00 4 Add a 100g calibration weight the display will show PASS and return to normal weighing mode 5 Put away the calibration weight and press ON OFF to turn of the scale and the calibration is finished Please check the availability of weights at the store you bought your scale from IV TROUBLESHOOTING The primary reasons for inaccuracy or malfunction are low batteries incorrect calibration overload or operating on an unstable surface Please keep this in mind and maintain and operate your scale properly This scale is a precise instrument a2. AWS Anercan Weigh Scales Inc AMW Series m co Core nove EJ AMW 50 ns User Manual AMW 250 AMW 350 AMW 500 AMW Series Manual Thank you for purchasing the American Weigh AMW Series digital scale Please read all operating instructions carefully before use This electronic scale is a precision instrument With normal care and proper treatment it will provide years of reliable service Never load the scale with more than the maximum capacity Overloading will permanently damage it Avoid any exposure to extreme heat or cold Your scale works better when operated at normal room temperature Always allow the scale to acclimatize to normal room temperature for at least one hour before use Give your scale sufficient warm up time Usually 30 60 seconds before calibration to give the internal components a chance to stabilize Keep your scale in a clean environment Dust dirt moisture vibration air currents and a close distance to other electronic equipment can all cause an adverse effect on the reliability and accuracy of your scale Handle with care Gently apply all items to be weighed onto tray top Although this scale is designed to be quite durable try to avoid rough treatment as this may permanently damage the internal sensor Avoid shaking dropping or otherwise shocking the scale This is a precision instrument
3. and must be handled with extreme care Only operate the scale on a stable vibration free surface I OPERATION Place Scale on a horizontal flat surface 1 Press ON OFF key 2 Wait until 0 0 is displayed 3 Put the object s on the weighing platform 4 Using the MODE key you can switch between the weighing units Il TARE WEIGHING 1 Turn on scale as described above 2 Place the tare item on the platform 3 Press TARE and wait until 0 0 is displayed 4 Add the net weight item Ill CALIBRATION Calibration is NOT required before first use Only calibrate if scale is not weighing properly Make sure you use the correct calibration weight for your scale or the calibration will not be accurate AMW 50 50g calibration weight AMW 100 100g calibration weight AMW 250 200g calibration weight AMW 350 300g calibration weight AMW 500 500g calibration weight Calibration Procedures for AMW 250 350 500 1 Turn OFF the scale press and hold the CAL key and then press ON OFF shortly After 1 2 seconds the scale will display a random number Now release the CAL key 2 Wait 2 seconds and press ON OFF key again shortly 3 The LCD display will read 2ero followed by the amount of weight required to calibrate listed above 4 Place the required calibration weight on the platform ie AMW 250 place a 200g on the scale 5 Press ON OFF again The LCD display reads CAL then
4. nd must be handled with the utmost care and caution Display Elimination of errors Nothing Battery Symbol lo or 88888 Change the batteries OUE2 Recalibrate the scale as shown above EEEEE You are overloading the scale Remove the excessive load immediately LLLLL The delicate weighing load cells have been damaged by misusing the scale i e it was shocked dropped or overloaded You can try recalibrating the scale If the load cell has not been damaged too much it will work again after recalibration UNST Use the scale in a more stable position Specifications Capacity AMW 250 AMW 350 AMW 500 AMW 100 250g 350g 500g 100g 8 820z 12 350z 17 640z 8 540zt 11 250zt 16 08 ozt 160 8dwt 225 1dwt 321 5dwt Resolution 0 01g 0 1g 0 0050z 0 0050zt 0 1dwt 2 5 x 3 Stainless Steel Backlight Calibration Weight not Included Platform Dimensions inches 100g Scale Dimensions inches Gross Weight 5x3 x 0 75 2 x AAA Batteries included 0 36 Ib 0 43 Ib 0 36 Ib
Download Pdf Manuals
Related Search