INTELLIGENT LED COLOR SYSTEM FL
Contents
1. strain mechanically put pressure on pull or heat up the power cord Never operate next to sources of heat or cold Disregard can lead to power cord damages fire or mortal electrical shock The cable insert or the female part in the device must never be strained There must always be sufficient cable to the device Otherwise the cable may be damage which may lead to mortal damage Make sure that the power cord is never crimped or damage by sharp edged Check the device and the power cord from time to time If extension cords are used make sure that the core diameter is sufficient for the required power consumption of the device All warning concerning the power cord are also valid for possible extension cords Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord Otherwise the cable or plug can be damage leading to mortal electrical shock If the power switch is not accessible The device must be disconnected via the mains If the power plug or the device is dusty the device must be taken out of operation disconnected and then be cleaned with a dry cloth Dust can reduce the insulation which may lead to mortal electrical shock More severe dirt in and at the device should only be remove by a specialist There must never be any object entering into the device This is especially valid for metal parts If any metal parts l2. INTELLIGENT LED COLOR SYSTEM FL 672 User Manual www flash butrym pl Page 1 COUTION keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initially start up Every person involved with the installation operation and maintenance of this device has to Be qualified Follow the instructions of this manual Consider this manual to be part of the total product Keep this manual for the entire service life of the product Pass this manual on to every further owner or user of the product Download the latest version of the user manual from the internet gt gt gt INTRODUCTION Thank you for having chosen FL 672 Intelligent LED color System If you follow the instructions given in this manual We are sure that you will enjoy this device for a long time The FL 672 Intelligent LED Color System features a built in microphone Unpack your FL 672 Intelligent LED Color System Before you initially start up Please make sure that three is no damage caused by transportation Should there be any Consult your dealer and do not use the device SAFETY INSTRUCTION CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock hen touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation It is absol
3. can fall down if the main attachment fails When rigging dragging or servicing the device staying in the area below the installation place on bridges under high working places and other endangered area is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installation are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installation are approved by a skilled person once a year PROCEDURE The device should be installed outside area where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualification do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily and or damage to property The device has to be installed out of the reach of people If the device shall be lowered from the ceiling or high joists professional trussing systems have to be used The device must never be fix
4. ddr when there is DMX connection indicates the present DMX Address But When there is no DMX connection instead it will display the preset non DMX running mode Auto Sound or Manual When you operate it again the LCD will return to the last menu option before idling ADDRESSING The control Board allows you to assign the DMX fixture address which is defined as the first channel from which the FL 672 Intelligent LCD Color System will respond to the controller For address setting press the rolling wheel and turn it clock wise to decrease value anti to increase www flash butrym pl Page 7 Press again to confirm Note Overlapped address codes for different fixtures are not suggested Exception see Combinations of Group Mode and Channel Mode It s necessary to insert the XLR termination plug with 120 Ohm in the last lighting in the link in order to ensure proper transmission on the DMX data link LED BRIGHTNESS ADJUSTMENT The Control Board allows you to adjust the brightness of the LEDs by manual To adjust press the rolling wheel and turn it till show Manual Blue to adjust the brightness of the blue LEDs Manual Green to adjust the brightness of the green LEDs Manual Red to adjust the brightness of the red LEDs The adjusting value ranges from 0 255 the higher the value the brighter the blue LEDs To enter these settings press the wheel Clock wise to decrease the value anti to increase Press again t
5. de are evenly divided in 8 square blocks which can be grouped with differ numbers of block To set the group press the wheel and roll it till it shows DMX Mode 8 Group 4 Group 2 Group 1 Group 8 4 2 1 here indicate the number of LED block s For example 1 Group means each single LED block is a gro 2 Group means 2 LED block are in 1 group 4 Group 4 in 1 8 Group all 8 LED block are in 1 group Once desired option selected press the wheel again to confirm www flash butrym pl Page 8 DMX MODE CHANNEL Each LED group has 3 channel mode and 6 channel mode To set the channel mode press the wheel and roll till it shows DMX Mode 3Channel1 6Channel To set the channel mode press the wheel and roll it Clockwise for 6 Channel mode Anti for 3 Channel mode press the wheel again to confirm DMX protocol of 3 channel mode Channel 1 Red Decimal Percentage Feature 01 255 I 0 100 Red LEDs from close to full on Channel 2 Green Decimal Percentage Feature 01 255 100 Green LEDs from close to full on Channel 3 Blue Decimal percentage Feature 01 255 100 Blue LEDs from close to full on DMX protocol of 6 Channel Mode Channel I RGB Decimal Percentage Feature 014 No function 51255 1100 Full on Channel 2 Red Decimal Percentage Feature 01 255 I 096 110096 Red LEDs from close to full on Channel 3 Green Decimal Percentage Feature 01 255 100 Green LEDs from close to full on Chan
6. ed swinging freely in the room COUTION Devices in hanging installation may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do not install the device Before rigging make sure that the installation area can hold a minimum point load of 10 times the device s weight DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5 meter Mount the device to your trussing system using an appropriate clamp For overhead use always install a safety rope that can hold at least 12 times the weight of the fixture You must only use safety rope with quick link with screw cap Pull the safety rope through the attachment eyelet and over the trussing system or a safe fixation spot Insert the end in the quick link and tighten the safety screw www flash butrym pl Page 6 The maximum drop distance must never exceed 20 cm A safety rope which already hold the strain of a crash or which is defective must not be used again Adjust the desired inclination angle via the mounting bracket and tighten the fixation screws Connect the fixture to the mains with the power plug The occupation of the connection cables is as follow Cable pin international Brown live L Blue Neutral N Yellow Green Earth O The earth has to be connected If the device will be directly connected with the local power suppl
7. ike staples or coarse metal chips enter into the device the device must be taken out of operation and disconnected immediately Malfunction or short circuits caused by metal part may cause mortal injuries During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective HEALTH HAZARD Never look directly into the light source as sensitive persons may suffer an epileptic shock especially meant for epileptics Keep away children and amateurs Never leave this device running unattended OPERATING DETERMINATIONS This device is a lighting effect for creating decorative effects This product is allowed to be operated with 110v and 220v 47 64Hz and was designed for indoor use only This device is designed for professional use e g On stages in discotheques theatres etc www flash butrym pl Page 3 Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others This device must never be operated or stockpiled in surrounding where splash water Rain moisture or fog ma
8. nel 4 Blue Decimal percentage Feature 01 255 100 Blue LEDs from close to full on Channel 5 Strobe Decimal Percentage Feature 114 0 12 No function 51253 2 2 Strobe from slow to fast 2541255 97 1100 Full on Channel 6 Built in Programs 014 0 12 No function 5130 2 112 RED 31160 12 124 GREEN 61190 24 135 l BLUE 911120 36 147 RED GREEN 1211150 47 159 RED BLUE www flash butrym pl Page 9 1511180 59 171 GREEN BLUE 1811210 71 182 RGB FULL 2111240 83 194 No function 2411255 95 1100 Sound activation mode COMBINATIONS OF GROUP MODE AND CHANNEL MODE When the FL 672 is set as in 8 Group and 3Channel it means all 8 LED block of the FL 672 are in one group and the group has got only 3 channels CH CH CH CH CH CH CH I CH 1 3 1 3 1 3 1 3 1 3 1 3 1 3 11 3 4 Group 3Channel As 4 LED block are in one group so the 8 LED block are divided into 2 group each group has got 3 channels which makes the fixture with total 6 channels CH CH CH CH CH CH CH ICH 1 3 1 3 1 3 1 3 14 6 4 6 4 6 14 6 2 Group 3Channel As 2 LED block are in one group so the 8 LED block are divided into 4 group each group has got 3 channels which makes the fixture with total 12 channels CH CH CH CH CH CH CH ICH 1 3 1 3 1 3 1 3 14 6 4 6 4 6 14 6 1 Group 3Channel As 1 LED block a
9. o confirm NON DMX RUNNNING MODES To set non DMX running modes disconnect the fixtures from the DMX controller and then press the press the rolling wheel and turn it Till shows No DMX Auto Sound Manual To enter this setting press the wheel Auto Sound Manual are in sequence Auto indicates the Auto Running Mode Sound the sound activation mode and Manual the manual Operation Mode Press the wheel again to confirm when the desired running mode is selected CHASE A chase is a sequence of different steps that will be called up one after another in a continuous loop With FL 672 Intelligent LED Color System you can select up to 8 different chasers with speed and fide time adjustable For example to set fade time of chase 8 press the rolling wheel and turn it till shows Chase 8 Pay attention to position of the cursor When the cursor is flashing right after the letter f as show above press the wheel then you can adjust the fade time of Chase 8 Press again to confirm Chase 8 s_ Also pay attention to position of the cursor When the cursor is flashing right after the letter s as show above press the wheel then you can adjust the running speed of Chase 8 Press again to confirm NOTE Before pressing the wheel You can switch between the options s and by rolling the wheel back or for Chase 1 to Chase 7 are with the same operation as described in Chase 8 moa f DMX MODE GROUP The LED at FL 672 s front si
10. ode the DMX address codes of these FL 672 is can also be set as the same code Of course they will run the same as well Except for this case however overlapped DMX address codes are not suggested MASTER SLAVE RUNNING MODE When two or more FL 672 is are connected together disconnect the DMX signal and set one or more FL 672 is to Sound Activation Mode see No DMX Auto Sound Manual the FL 672 is are then in master slave running mode Note The master will be randomly selected as one of the sound activated fixtures and it is not fixed it can change to another sound activated fixture at any time CLEANING AND MAINTENANCE DANGER TO LIFE Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a soft lint free and moistened cloth Never use alcohol or solvents There are no serviceable parts inside the device except for the fuse Maintenance and service operations are only to be carried out by authorized dealer REPLACING THE FUSE If the fine wire fuse of the device fuses only replace the fuse by another fuse of the same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Take out the fuse holder under the power supply Step 2 Remove the old fuse from the fuse holder Step 3 Install the new fuse in the fuse holder Step 4 Replace the fuse holder in the housing and fix it Should you need any spare parts please use genuine par
11. ofessional operation Never use solvents or aggressive detergents in order to clean the device Rather use a soft and damp cloth Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forbidden due to safety reasons Never remove the serial barcode from the device as this would make the guarantee void If this device will be operated in any way different to the one described in this manual the product may suffer damage and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit Bums electric shock lamp explosion crash etc www flash butrym pl Page 4 OVERVIEW FRONT 8 5 2 1 4 6 7 3 BACK 1 power supply and fuse holder 2 DMX OUT 3 DMX IN 4 FAN 5 Microphone 6 LCD Display 7 Function wheel 8 Bracket INSTALLATION Overhead rigging DANGER TO LIFE Please consider your local standard and norms during the installation The installation must only be carried out by an authorized dealer The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation www flash butrym pl Page 5 The installation must always be secured with a secondary safety attachment e g An appropriate catch net This secondary safety attachment must be constructed in a way no part of the installation
12. re in one group so the 8 LED block are divided into 8 group each group has got 3 channels which makes the fixture with total 24 channels CH CH CH CH CH CH CH ICH 1 3 4 6 7 9 10 12 13 15 116 18 119 21 122 24 8 Group and 6 Channel All 8 LED block are in one group and the group has got 6 channels CH CH CH CH CH CH CH ICH 1 6 1 6 1 6 1 6 1 6 1 6 1 6 11 6 4 Group 6Channel As 4 LED block are in one group so the 8 LED block are divided into 2 group each group has got 6 channels which makes the fixture with total 12 channels CH CH CH CH CH CH CH ICH 1 6 1 6 1 6 11 6 17 12 I7 12 7 12 V7 12 2 Group 6Channel As 2 LED block are in one group so the 8 LED block are divided into 8 group each group has got 6 channels which makes the fixture with total 24 channels CH CH CH CH CH CH CH ICH 1 6 1 6 17 12 17 12 13 18 113 18 119 24 119 24 1 Group 6Channel As 1 LED block are in one group so the 8 LED block are divided into 8 group each group has got 6 channels which makes the fixture with total 48 channels CH CH CH CH CH CH CH ICH www flash butrym pl Page 10 1 6 7 12 113 18 119 24 125 30 131 36 137 42 143 48 Channel of each group will run accordingly to its preset channel mode 3 Channel Mode or 6 Channel mode If two or more FL 672 is are set in the same combination of Group Mode and Channel m
13. ts If the power supply cable of this device becomes damaged it has to be replaced by authorized dealers only in order to avoid hazards Should you have further questions please contact your dealer TECHNICAL SPECIFICATION Power supply 110V 220V AC 47 64 Hz Power consumption 70W Sound control Via built in microphone www flash butrym pl Page 11 Packing size LxWxH 1455x 255 x 185 mm Net Weight 14 3 kg Gross Weight 15 7 kg Maximum ambient temperature 145 C Maximum housing temperature t steady state 60 C Fuse I TIA 220 V Please note Every information is subject to change without prior notice www flash butrym pl Page 12
14. utely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Please make sure that there are no obvious transport damage Should you notice any damages on the A C connection cable or on the casing Do not take the device into operation and immediately consult your local dealer This device falls under protection class 1 The power plug must only be plugged into a protection class 1 outlet The voltage abd frequency must exactly be the same as stated on the device Wrong voltage or power outlet can lead to the destruction of the device and to mortal electrical shock www flash butrym pl Page 2 Always plug in the power plug last The power plug must always be inserted without force Make sure that the plug is tightly connected with the outlet Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Never touch them with wet hands As this could lead to mortal electrical shock Never modify Bend
15. y harm the device Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks When using smoke machines make sure that the device is never exposed to the direct smoke jet and is installed in a distance of 0 5 meters between smoke machine and device The room must only be saturated with an amount of smoke that the visibility will always be more than 10 meters The ambient temperature must always be between 5 c and 45 c keep away from direct insulation particularly in car and heaters The relative humidity must not exceed 50 with an ambient temperature of 45 c This devise must only be operated in an altitude between 20 and 2000 m over NN Never use the device during thunderstorms Over voltage could destroy the device Always disconnect the device during thunderstorms This device is only allowed for an installation via the mounting bracket In order to safeguard sufficient ventilation leave 50 cm of tree space around the device The housing must never touch surrounding surfaces or objects Make sure that the area below the installation place is blocked when rigging dragging or servicing the fixture Always fix the fixture with an appropriate safety rope The maximum ambient temperature t a 45 c must never be exceeded Operate the device only after having familiarized with its function Do not permit operation by persons not qualified for operating the device Most damages are the result of unpr
16. y network a disconnection switch with a minimum opening of 3mm at every pole has to be included in the permanent electrical installation Lighting effects must not be connected to dimming pack DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expect OPERATION Initialization After you connected the effect to the mains the FL 672 Intelligent LED Color system starts running the LCD will display FLASH FL 672 while the fixture in initializing After initialization the LCD will display Addr when there is DMX connection indicates the present DMX address But when there is no DMX connection Instead It will display the preset non DMX running mode Auto Sound or Manual LCD MENU SEQUENCE Roll the wheel by the LCD clockwise it will show menu options in the following sequence Addr Manual Blue manual Green Manual Red No Dmx Auto Sound Manual Case ge Chase 8 Chase 7 Chase Ty Chase tr Chase 6 Chase 5 mee Pee Chase 5 Chase 4 Chase 4 Chase 3 Chase 3 Chase 2 RK LEK Chase 2 Chase 1 Chase 1 DMX Mode 8 Group 1 Group DMX Mode 3Channel 6channel The Above sequence is looping and revertive when roll the wheel anti clockwise Press the rolling wheel to enter settings of the desired menu option NOTE Whenever idle for 3 seconds the LCD will faint down its background illumination and will display A
Download Pdf Manuals
Related Search