RM185-ID1 LCD Monitor
Contents
1. a OUT OF SIGHT PEACE OF MIND at RM185 ID1 LCD Monitor TFT LCD MONITOR User s Manual FCC STATEMENT nt or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Only shielded interface cable should be used Finally any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the user s authority to operate such equipment Table of Contents Important safety instruction Product feature Product installation Function Keys MENU function Timing guide Input signal detail Product specification Trouble shooting Important safety instruction Do not scratch the screen of the LCD monitor with sharp materials such as nails and pens Take care not to use damaged cords and keep this product out of reach of children and persons who are not involved in using the product Choose a fresh and dry area and protect the monitor from extreme conditions of temperature and humidity dust and smoke Adequate temperature 0 40 C Adequate humidity 30 80 RH Check the power voltage before connecting to the AC power cable The interior part of the monitor is composed of ele2. Time Adjusts OSD menu screen s marking time within the screen possible to set the time for disappearance of OSD menu screen up to 30 seconds when OSD operation button is not pushed Max30sec Language Changes language on the OSD menu Seven languages are available English French German Spanish Chinese Japanese Korean gt Signal Source VGA Input signal User can select input signal depending on installed device VGA Only Mute Volume Adjusts size of sound Mute Turns audio function On Off gt Setting Reset Automatic color adjustment Automatically adjusts screen s color P Auto Exit Return to initial screen Timing Guide gt Timing guide This product is a multi frequency monitor It functions in horizontal frequencies from 30kHz to 80kHz and vertical frequencies from 56Hz to 75Hz Due to tis design based on microprocessor It offers the functions of automatic synchronization and automatic size Resolution Frequancy Horizontal Vertical Horizontal Vertical 640 480 37 9kHz 60Hz 640 480 37 9kHz 72Hz 640 480 37 5kHz 75Hz 800 600 35 1kHz 56Hz 800 600 37 9kHz 60Hz 800 600 48 1kHz 72Hz 800 600 46 9kHz 75Hz 1024 768 48 4kHz 60Hz 1024 768 56 5kHz 70Hz 1024 768 60 0kHz 75Hz 1280 768 48 0kHz 59Hz 1280 1024 64 0kHz 60Hz 1280 1024 80 0kHz 75Hz 1360 768 48 0kHz 59Hz 1366 768 48 0kHz 59Hz Input signal d
3. and contrast gt Image is unstable unfocused Use AUTO TUNE to adjust automatically If the image is still unstable after AUTO TUNE processing please adjust PHASE manually to get image focused Check whether the resolution or refresh rate in windows display setting is beyond supported range please refer to the specification of supported mode gt Flickering Not enough power is being supplied to the monitor Connect the monitor to a different outlet If a surge protector is being used there may be too many devices plugged in See Timing Guide in this manual with a list of refresh rates and frequency settings showing the recommended setting for the monitor gt Wrong or abnormal colors If any colors Red Green or Blue are missing check the VGA cable to make sure it is securely connected Loose pins in the cable connector could cause a bad connection Connect the monitor to another computer Check the graphics card for proper sync scheme or sync polarities to match the monitor s specifications gt Double split screen image Make sure your graphics card is set to Non Interlaced mode gt Entire screen image rolls scrolls vertically Make sure the input signals are within the LCD monitor s specified frequency range Maximum 1366 768 59Hz Connect the VGA cable securely Try the monitor with another power source gt Control buttons do not work Press only one button a
4. ast ratio Typ 1000 1 Brightness Typ 250 cd m Response Time Typ 5 ms Refresh rate MAX 1366 x 768 59Hz for optimal display Connectors Input signal 15 Pin VGA Audio in Power DC 12V In Voltage Power Input AC 100 240V 50 60Hz Output DC 12V Consumption 36W MAX Screen size MAX 409 8 mm H x 230 4 mm V Feature Temperature 32 F 104 F 0 C 40 C Humidity 30 RH 80 RH no condensation Altitude To 10 000 feet Storage Condition Temperature 4 F 140 F 20 C 60 C Humidity 5 RH 90 RH no condensation Dimension With stand 456 21 W x 370 72 H x 155 1 D Without stand 456 21 W x 370 72 H x 69 03 D Box Outside 506 W x 370 H x 140 D Weight Unit Box 4 5 kg Function Speaker 2W x 1 Audio in out Mono Mini Jack 1 5M The design amp specifications of RM185 ID1 are subject to be changed without any pervious notice to improve its quality Troubleshooting gt No power Flip the power switch ON The Power LED turns on Make sure AC DC power cord is securely connected to the power jack and to a power outlet gt Power on but no screen image Make sure the VGA cable attached with this monitor is tightly secured to the VGA output port on the back of the device Adjust the brightness
5. ctric elements If the monitor is broken do not try to disassemble it because it is necessary to contact appropriate technical services in order to have the product repaired a x A um Disconnect the power cable when the monitor is not used during a long period of time while you are away from home The LCD monitor screen can be damaged in the case that you clean the surface by using acetone ethyl alcohol or acid detergent Take care so that the monitor is not in contact with magnetic materials metals and inflammable substances Take care of the LCD monitor so that it is not damaged by the external impact Do not use this product near the windows receiving direct sunlight or direct natural light G A Do not install the monitor in a sloping place that is not safe due to the fact that the product can fall down and be broken thus doing harm to other persons Product feature gt Introduction This monitor is a high resolution monitor has features of electromagnetic wave blocking reduction in electricity consumption and efficient use of space It is recommendable to read this manual before using this product gt Product features 1 This monitor RM185 ID1 has an 18 5 inch flat surface color active Matrix TFT LCD with pixel size of 0 8mm H X 0 3mm V for an ultra precision high resolution image 2 The RM185 ID1 uses an 18 5 inch TFT LCD Thin Film Transistor Liquid Crystal Di
6. etail gt Cable Connections Input Output Cable Type DC Power DC Power Cord Audio IN Audio Cable VGA IN 15 pin VGA Signal Cable P Plug amp Play The adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion Your PC system can easily identify and configure itself for use with your display This monitor automatically tells the PC system its Extended Display Identification Data EDID using Display Data Channel DDC protocols so the PC system can automatically configure itself to use the flat panel display gt Warm Up Time All LCD monitors need time to become thermally stable whenever you turn on the monitor after letting the monitor be turned off for a couple of hours Therefore to achieve more accurate adjustments of parameters allow the LCD monitor to be warmed up for at least 30 minutes before making any screen adjustments When the condition of the screen is not good please press the AUTO button This function may cause some temporary noise on the screen depending on VGA cards Product specifications Type 18 5 diagonal viewable screen TFT Thin Film Transistor Active matrix panel Pixel Pitch R G B vertical stripe Display Color 16 777 216 colors Viewing Angle H V 170 160 Contr
7. splay panel and supports 1366 x 768 maximum resolution 3 The RM185 ID1 is a monitor whose deflection frequency is transformed automatically up to 30 80KHz horizontally 56 75Hz vertically 4 The RM185 ID1 is compatible with IBM PC and Apple Macintosh A different adaptor is necessary for apple macintosh 5 The RM185 ID1 has a power saving function less than 36W in power ON mode less than 2W in stand by and 1W in power off 6 The RM185 ID1 supports DDC Plug amp Play mode Product installation gt Components LCD Monitor Power Cord VGA Cable User S Guide Adaptor Audio Cable Notice Please make sure the following items are included with your monitor If any items are missing contact your dealer Please use the cables that are provided REVO does not take responsibility for any problems that arise from using any other cables gt Installation Please turn off the RM185 ID1 before connecting any device to it Connect adaptor cable to DC power on on the rear side of the RM185 ID1 then connect power cord to adaptor RM185 ID1 has 15pin VGA port Connect the cables properly to your DVR between VGA Turn on your DVR and RM185 ID1 Display conditions with can be adjusted by pushing control buttons on the right side of the RM185 ID1 At the user s convenience you can adjust the display angle of the RM185 ID1 under 25 degree to backward Please t
8. t a time gt When the message of out of range appears Restart the computer and while it is restarting press F8 until the Startup menu appears Then enter to start the computer in safe mode Right click the desktop click Properties and click Settings Click Advanced click Adapter and then click Adapter Default from the Refresh Rate Click OK Click OK again and then click Yes to restart the computer in Normal mode You can set the colors and screen area to your preferences
9. urn off the RM185 ID1 when not in use i Adjusting LCD panel angle Do not hold or press down on the monitor s screen while adjusting angle since LCD panel maybe damaged or break if severe Do not lean backward excessively so that the monitor dose not fall backwards Be careful of potential damage to the stand while adjusting angle Function Keys gt Operation of the function keys Function Automatically adjusts the picture Opens the Main Menu Up Right VOLUME up Down Left VOLUME down ON OFF gt On Screen Display OSD Menu Navigation 1 Press the MENU button the main OSD menu will be appear on the screen 2 Press the A Y buttons to navigate through the menu then press the MENU button to make the selection 3 To navigate out of a menu press the AUTO button MENU MENU Open Menu Screen Move to main category Select main category Move to sub category wo m a 17 Close Menu Screen Save set value Adjust set value Select sub category gt Color Contrast Brightness Color Adjust Color Temp gt Image Setting Clock Phase Sharpness H position V position gt OSD Menu OSD H Pos OSD V Pos OSD Timer Language 50 w OSD Horizontal Adjustment Adjusts OSD menu screen s horizontal location OSD Vertical Adjustment Adjusts OSD menu screen s vertical location OSD Marking
Download Pdf Manuals
Related Search