AM2020 User Manual
Contents
1. s30uUA Consumption Armed Power 60mW lt 40mA Consumption Wireless Up to 50m Transmission Range Radio 433MHz Frequency Sensor 71 L 34 W x 17 5 H mm Magnet 51 L x 12 W x 13 5 H mm Dimensions Operating O G 55 6 Temperature Operating 0 80 Humidity FOR INDOOR USE ONLY D3 D3 D3 HOME MODE NORMAL SINGLE DELAY ZONE ZONE ZONE IMPORTANT WHEN THE ZONE SETTING IS CHANGED THE SENSOR MUST RE PAIR WITH AM2000 CONTROL PANEL WIRELESS DOOR WINDOW CONTACT SENSOR AM2020 OSION PROFESSIONAL SECURITY SYSTEM 6 TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE Sensor has no power or not powering up Battery is loose or The sensor and AM2000 control panel are not paired No interaction between sensor and AM2000 control panel Poor No signal Signal interference out of transmission range or low battery unplugged low battery SUGGESTED REMEDY Replace battery alkaline type battery recommended Ensure battery is secured Please pair the sensor and AM2000 control panel following pairing instruction Relocate sensor away from water air conditioner refrigerator radio transmitting devices metal objects heater oven any heat sources rapid temperature changing high air flow locations or major obstacles Relocate the sensor closer to AM2000 control panel Replace battery 7 WARNING gt Do not drop puncture or violently shake th2. OSION PROFESSIONAL SECURITY SYSTEM WIRELESS DOOR WINDOW CONTACT SENSOR AM2020 ACCESSORY ONLY USE WITH 2000 INSTRUCTIONS FOR USE IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY ONION PROFESSIONAL SECURITY SYSTEM IMPORTANT PLEASE CONTACT IF YOU HAVE ANY CONCERNS OR PROBLEMS WITH THIS PRODUCT Customer Service Phone 03 9982 5111 Monday to Friday 8 30am 5 30pm EST Email customerservice orionlive com au 1 IDENTIFICATION LED INDICATOR 1 MAGNET 9 SENSOR N WARNING i 4111 ly 11 eS WIRELESS DOOR WINDOW CONTACT SENSOR AM2020 2 INSTALLATION AND NOTICES 1 Slide open the rear case and remove battery insulation strip 2 Mount the sensor on the door frame and the magnet on the door 3 Ensure the magnet is on the right side of the sensor where the arrow is located 4 Place the sensor in the desired location mount the magnet no more than 10mm away from the sensor and secure the sensor and magnet with double sided tapes supplied or screws not supplied 5 Avoid mounting sensors in areas with large quantity of metal or electrical wiring such as full metal frame and door furnace or
3. or authorise the retailer to assess any claim you may make on the Warranty in the above manner and if in 5 reasonable opinion the Warranty applies Arlec will at its own option and expense or authorise the retailer to replace the product with the same or similar product or repair the product and return it to you or refund the price you paid for the product Arlec will bear its own expenses of doing those things and you must bear any other expenses of claiming on the Warranty The Warranty is in addition to other rights and remedies you may have under a law in relation to the product to which the Warranty relates Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure Australia Pty Ltd ACN 009 322 105 gives the Warranty Arlec s telephone number address and email address Customer Service 03 9982 5111 New Zealand Toll Free 0800 003 329 Building 3 31 41 Joseph Street Blackburn North Victoria 3130 Blackburn North LPO P O Box 1065 Blackburn North 3130 Email custservice arlec com au CPIN002638 3 WIRELESS DOOR WINDOW CONTACT SENSOR AM2020
4. e sensor gt Do not mount directly expose or put near to the sun water air conditioner refrigerator radio transmitting devices metal objects heater oven any heat sources rapid temperature changing or high air flow locations gt Do not cover the sensor mount the sensor at adequate locations and heights gt Handle the sensor with care avoid unnecessary force or impact gt This sensor is for indoor use only 8 WARRANTY Arlec guarantees this product in accordance with the Australian Consumer Law Arlec also warrants to the original first purchaser of this product you from a retailer that this product will be free of defects in materials and workmanship for a period of 12 months from the date of purchase provided the product is not used other than for the purpose or in a manner not within the scope of the recommendations and limitations specified by Arlec is new and not damaged at the time of purchase has not been subjected to abuse misuse neglect or damage has not been modified or repaired without the approval of Arlec and has not been used for commercial purposes Warranty If you wish to claim on the Warranty you must at your own expense return the product and provide proof of original purchase and your name address and telephone number to Arlec at the address below or the retailer from whom you originally purchased the product within 12 months from the date of purchase Arlec will
5. utility room 3 INTERNAL AND FUNCTIONS TAMPER SWITCH when the case is opened during armed state the tamper switch will be triggered and generate a signal to alarm the AM2000 control panel TAMPER SWITCH ZONE SETUP ZONE SETTING set the jumpers to different zone mode for different alarm activation method HOME MODE ZONE when home mode button is pressed on AM2000 control panel or the remote control it will not trigger the alarm and therefore occupants can move freely inside the room Meanwhile other zone setting will remain armed NORMAL ZONE when 2000 is armed if intruder detected it will trigger alarm immediately SINGLE DELAY ZONE when 2000 is armed if intruder detected it will trigger alarm after 30 seconds time delay in default settings Note AM2020 wireless door window contact sensor is set to SINGLE DELAY ZONE by default DO 4 OPERATION Pairing with AM2000 control panel Key in the password and press the connect key on AM2000 control panel then trigger the sensor by opening the door it is mounted on When one beep sound from the AM2000 control panel is heard they are paired To check if they are connected successfully arm the AM2000 control panel trigger the sensor unit by opening the door it is mounted on if there is an alarm the connection is successful 5 SPECIFICATIONS Power Supply _ 1 5V DC 1X AA 1 5V alkaline type battery Standby Power 0 045mW
Download Pdf Manuals
Related Search