Marina ENG Balboa.indd
Contents
1. e adequate hardness of bed adjusted to SPA weight f sufficient ventilation indoors g in case of a bath installed in a closed premise access to the electrical equipment must be provided for maintenance or inspection purposes _105 5 555 480 2 L 38015 2 3 BATH POSITIONING The floor should be very well leveled All the bath legs should be on a solid and hard surface The total weight of the bath with water is about 750 kg The weight of the bath should be equally spread over the 9 bath legs The figure below shows the points of support 1103 10 Location of the bath points of support 2 4 PREPARATION OF ELECTRICAL AND WATER CONNECTIONS The Marina SPA tub requires at most ca 5 6 kW of power The minimum cross section of the cord should be at least 3x4 mm In the case of tubs installed outdoors a cord with insulation resistant to deterioration caused bv weather conditions is required Protect the cord against mechanical damage If the insulation or cord is damaged always replace it due to the risk of electric shock For 3x4 mm cords protect the tub s power cord with a C type residual current device and a trigger current of 25 A For safety reasons always connect the tub s power cord to the mains using an electrical connection protected by a residual current device with a rated cut off current of 30 mA It is recommended to check the resid2. please fill with installer in manual the card with the details requested to ensure validitv of warrantv Please remember to get from sales agent confirmation of purchasing date 1 The product must be installed strictly in accordance with the installation instructions that come with the product and respecting all the measurements and indications given 2 For the warranty to be operative all work done during the warranty period must be carried out by a autho rised service The list of authorized service is available by Your sales agent The warranty period POOLSPA Sp z provides a full guarantee for the Spa for a period of 2 years from the date of installation During this full guarantee period any manufacturing or operating defect will be repaired at no cost to the user excluding the bulbs If the product is installed in a country other than the country of acquisition the period and terms of the warranty will be restricted to the general warranty cover stipulated by regulations in the country concerned After 2 years from the date of installation POOLSPA Sp Z 0 0 provides post warranty payable service 4 The warranty will not be valid in these cases a a fault or faulty operation resulting from anomalies or non compliance with the product specific instal lation rules or arising in the hydraulic electrical or gas systems b corrosion scaling or abrasion caused by a lack of cleaning and or maintenance improper use creles
3. 2 C the entire equipment is shut off and the 6 ICE function is switched into stand bv mode e Operation mode ANTIFROST system is marked by ICE symbol the LCD screen e ANTIFROST mode is activated irrespective of the bathtub status e If during filtration mode ANTIFROST system starts filtration mode will be switch off 1 2 JETS SPA MARINA is equipped with an innovative jet system lt SEE fixed mini jets A fixed mini ozone jet E large rotary jets B large fixed jets C large fixed jets D 3 4 black tub drain F All jets are controlled The hydromassage can be intensified by turning the jets in a clockwise direction about 90 and an anti clockwise direction decreases hydromassage intensity and eventually closes the jets Replacement of jet inserts with identical diameters The inserts can be unscrewed by a firm hand movement in an anti clockwise direction and then taken out of its frame Another prepared insert may be fitted to the frame this time in a clockwise direction until stop The exchange should be performed while the bath is NOT operating Removing a jet insert Fixing a jet insert It is advised at least once every 6 months to take out from big jets their inserts for cleaning of any possible dirt Unscrew the insert from frame remove gently using pliers inner part of the jet Clean inner part of the jet Put back the inner part and screw the insert to the
4. frame in a clock wise direction 1 3 CONSERVATION SUBSTANCES The acrylic surface of the bath is covered with a thin layer of wax being the remaining of the polishing process Metallic elements have been coated with silicone oil for protection purposes The SPA should be washed off e g with a dishwashing detergent prior to filling the bath with water 1 4 VENTILATION High water temperature during bath in the bath 39 C causes emitting of big amounts of steam An efficient ventilation system should be provided in the room with the bath Installing of a steam condenser in the room which will maintain constant air humidity will minimize the risk of dampening of walls and ceiling An air conditioning system in the building allows for elimination of the steam condenser Such problem does not exist in case of a bath operating in open air conditions 1 5 MAIN FUNCTIONS ACCESSIBLE FROM THE ELECTRONIC CONTROL PANEL _ INV BLOWER LIGHT STANDARD SET HEAT ply TOL 88 CESS MODE PROG Marina SPA control panel 1 5 1 FIRST START UP FILL THE BATHTUB WITH WATER BEFORE FIRST START UP After power is turned on the spa bathtub switches to the pump venting mode When that mode press Jets button s several times to make sure that the pumps are not air locked The duration of the mode is less than 5 minutes Press Warm or Cool buttons to exit the mode After the venting is completed the bathtub will switch
5. responsible for their safety Children should be supervised to ensure that they do not play with the equipment Before taking a bath make sure that the water level in the bathtub is correct If the water level is 3 4 cm above the skimmer f Iter you can start the bath If the water level in the bathtub is not correct the f Itering system may not operate properly and water heating will not be possible Remember to add water into the bathtub from time to time Parts comprising active components excluding those supplied with safe voltage not exceeding 12V cannot be accessible for the person inside the equipment Parts comprising electrical components excluding remote control equipment should be located or fixed so that they cannot drop into the bathing equipment Keep this manual for future reference PART T INSTRUCTION MANUAL Congratulations on buving a SPA MARINA portable bathl Hvdromassage in the SPA MARINA bath can be enjoved bv even 3 people two places for lying and a seat The bath size makes it easy to carry it through any standard door the room does not also have to be large The bath is equipped with an ozonator which makes it easier to keep the water clean and is very effective in beauty treatment The qualities of ozone are described in detail in Part 1 8 of the manual page 13 Thanks to the antifrost system it is even possible to take a bath when the outside temperature is below freezing The SPA M
6. s serata menses PART 2 INSTALLATION MANUAL PR MB E 3970 ji 2 C Ee p E E E A E EE 2 9 BaN POSON IO EE E E eee eee 2 4 Preparation of water and electrical connections 2 5 Grounding cable connection 2 0 CONMEGHONM A A A WA ONIO VALV err et 2 0 Maintenance OF acrylic GIOMIGING sia eee a a i WARRANTY FOR SPA ie A a a i A EEEE EAS TECHNICAL PRODUC FSHEE eee CONTENTS sani ma ai Introduction In order to be able to fullv use all functions of a SPA Marina please read all sections of this manual Vou should remember that despite the therapeutic and relaxing function of a hvdromassage treatment seriously ill persons or persons suffering from heart disorder diseases or high blood pressure need to consider special conditions created inside the SPA baths and consult their physician before using such baths We recommend using hydromassage treatments in water of the average temperature of 37 degrees for approximately 20 minutes It is recommended that children using the equipment are always accompanied by an adult This equipment is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the equipment by persons
7. to standard operation mode EV 1 5 2 TEMPERATURE ADJUSTMENT 80 F 104 F 26 0 C 40 0 C When in standard operation mode the bathtub controller enables water temperature adjustment within the 8 range mentioned above Temperature of water inside the spa is displayed in a continuous manner The value displaved is correct if the pump has been operating for at least 2 minutes Press Warm or Cool button once to displav water temperature The preset temperature can be changed bv pressing the same buttons again lemperature adjustment mode is indicated bv a flashing value of the current setting Three seconds after the button is pressed for the last time the value indicated on the displav stavs on and the current spa temperature is displaved q 1 5 3 JETS 1 Press the Jets 1 button to start stop the pump 1 and toggle low high speed if available If the pump operates at low speed it switches off after 4 hours If the pump operates at high speed it switches off after 15 minutes Remember that it is not possible to deactivate the low speed when the filtration process is running 1 5 4 JETS 2 JETS 3 BLOWER IF AVAILABLE Press a given button once to start stop the corresponding device Each of the devices is turned off after 15 minutes 306 1 5 5 LIGHT Press the Light button to switch the spa light on The light is turned off after the button is pressed again The light switches off after 4 hours 1 5 6 S
8. A company has the policy of constant improvement of products and reserves the right to introduce changes to the specification and colours without a prior notifica tion However POOLSPA makes all efforts to ensure that the specifications are updated on the date of publishing ROCA POLSKA Sp z 0 0 Zaktad produkcyjny POOLSPA ul Dabskiego 35 72 300 Gryfice tel 48 91 38 777 00 fax 48 91 38 777 01 www poolspa pl e mail info poolspa pl 17 04 2013 3000028
9. ARINA bath comprises electronic control panel 2 airmassage aeration regulators 3 function hydromassage valve 3 kW electric heater 1 5 kW hydromassage pump axial blower with air heater 1 1 kW 0 8 kW blower and 0 3 kW air heater water ozonator UV lamp optional no ozone jet antifrost system for outside temperatures below freezing point water temperature sensor telescopic skimmer filter with replaceable cartridge set of jets 32 pcs including 1 ozone jet water suction point white underwater LED light multi color light optional LED spotlight 24 points optional 3 polyurethane cushions gray in a standard option wooden panel in mahogany or pine colour optional plastic panel in gray mahogany or pine optional wooden stairs in mahogany or pine colour optional thermal cover optional It is recommended to turn the power off with the manual switch before draining the tub to prevent the hydro massage pump from operating without water Any claims regarding a damaged pump operating without water will not be investigated 1 1 TECHNICAL SPECIFICATION SPA MARINA dimensions length 188 cm width 133 cm depth 70cm height 78 cm aluminium frame 1330 1110 80 cm wooden frame Capacity 580 litres Weight 150 kg without water and housing 605 aaa ee
10. ETTING THE TIME If the spa is operated for the first time SET TIME message is flashing on the display To change the current setting press the following buttons Time Mode Prog Warm or Cool one by one After the last button of the sequence is pressed the hour setting mode is activated The hour visible on the screen will be changed automatically To stop it from changing press Warm or Cool buttons one more time and press Time button to confirm the setting 1 5 7 MODE PROG There are three operating modes available for the controller The mode is changed by pressing Warm or Cool button In the standard mode the set temperature is maintained and the STANDARD icon is displayed When in the eco mode the spa is heated up to the preset temperature only during filtration cycles Fen message appears on the display Fen message and water temperature value are displayed alternately during pump operation When in the stand by mode the spa is heated up to the temperature of 20 F 10 C only during filtration cycle ILF message appears on the display LF message and the current water temperature value are displayed alternately during pump operation 1 5 8 SETTING FILTRATION CYCLES The controller can be operated in two filtration cycles The first preset filtration cycle starts at 8 00 a m and ends at 10 00 a m The other preset filtration cycle starts at 8 00 p m and ends at 10 00 p m During the filtration process pump 1 is operated at low spee
11. POOLSPA SPA Bath Marina 188 x 133 Installation and user manual Dear customers Thank you for trusting us and buying our product The POOLSPA company one of the leaders in the European hydromassage bath market has been offering its world class quality products for many years The endurance reliability and safety of our baths has always been of greatest importance to us that is why we always use materials and devices from reputable suppliers The manual will help yoy learn about the bath installation and its use In this way you will be able to use the bath without any problems for many years to come Have a great time and enjoy our baths lalicels lee saat ete tan ae PART 1 INSTRUCTION MANUAL Tele HOCMMICAI GpPetciiCato ti 1 3 216 4 KOR 1 5 Main functions accesible from the electronic control MASS AGE i a ee Nene Renee nee nen eek ne ee ee teen eee ce ee ee ee 1 7 Colourful led spotlight multi point led light Optional VLC OZ OPC IN 1 9 Marna SPA 4 00 3 1 10 DISIMIEGHOM i geaciinacnaneetaaenents 1 11 Measurement and treatment formula 5 1 12 Thermal cover additional OPproormal
12. ae 22 430 i 695 Bath dimensions wooden frame Bath dimensions aluminium frame Material and construction Acrylic strengthened by laminated polyester on an aluminum frame SPAs with panels are installed on wooden frame oniv Voltage 230V 50 Hz Electrical equipment 3 kW electric heater 1 5 kW hydromassage pump axial blower with air heater 1 1 kW 0 8 kW blower and 0 3 kW air heater Power cord 3 x 4 Rated power and power consumption 5 6 kW 22 5 A Maximum number of people in the bath 3 Water The water should come from the water system and be properly purifi ed and disinfected accordingly to DIN 19643 97 as well SIA 173 Well water is inadvisable unless it has special certificates in compliance with current norms ANTIFROST System The main function of the bathtub controller is to maintain the preset water temperature within the range between 26 and 40 C However the system features also a winter operation mode so called ANTIFROST to protect the piping from freezing The bathtub controller uses an integrated temperature sensor to control the ambient temperature in a continuous manner If the air temperature is lower than 7 2 C the winter mode is activated Turning the winter mode on involves activation of the entire electrical equipment of the bathtub pumps to prevent water from freezing in the spa Four minutes after the water has reached the temperature of 7
13. d with ozone generator on 1 5 9 CHANGE OF FILTRATION CYCLE It is not necessary to change the filtration cycles If for any reason it is necessary to change previously programmed adjustments FILTER 1 for a m and FILTER 2 for p m the controller allows doing this To change the cycles push the buttons consecutively during 3 seconds Time MODE PROG MODE PROG It will appear the communicate SET START FILTER 1 on the screen Change the time of starting the filtration by pushing the buttons Warm or Cool To put new adjustments into memory of the controller push the button MODE PROG The svstem will be switched to the mode of SET STOP FILTER 1 Changing the time of finish the filtration will be done bv pushing the buttons Warm or Cool the same wav as above programming START FILTER 1 Approval of the new adjustments will be done bv pushing the button MODE PROG Programming the filtration for the afternoon FILTER 2 suppose to be done the same way as for the a m 1 5 10 LOCKING THE PANEL Press the Time Blower and Warm buttons in that order within 3 seconds The panel will be locked To unlock it press the Time Blower and Cool buttons in that order within 2 seconds 1 5 11 BLOCKING TEMPERATURE CHANGES Press the Warm Time Blower and Warm buttons in that order within 3 seconds The Warm and Cold buttons will be locked To unblock temperature changes press the Time Blower and Cool buttons in that order within 2 seconds Diagnostic messag
14. es Message description Required action oe as The control panel is inactive until the power is on The No message is displayed No power SPA settings remain unchanged until the spa is switched on again The pump must operate for 2 minutes before current Unknown temperature water temperature can be displayed DO NOT GO INTO THE WATER Remove the SPA cover ALALA Overheating SPA switched off A and wait for the water to cool down Once the water is LI H sensor indicates the heater temperature cooled reset the system by pressing any button If reset exceeded 118 F 47 8 C is not possible unplug the SPA and contact your local dealer or service center DO NOT GO INTO THE WATER Remove the SPA Overheating SPA switched off A cover and wait for the water to cool down Once the sensor indicates the water temperature temperature drops to 107 F 41 7 C the SPA should reset exceeded 110 F 43 5 C automatically If reset is not possible unplug the spa and contact your local dealer or service center If the problem persists contact your local dealer the service centre This error mav occur temporarilv as a result of overheating SPA switched off The sensor connected to the A sensor socket does not work If the problem cannot be solved contact your local dealer or service center This error mav occur temporarilv as a result of overheating SPA switched off The sensor c
15. et the message has been displayed three automatically The message is reset by pressing any times dr The spa is switched off button No action is necessary All devices will switch on regardless of the condition of the spa The devices remain on for 4 minutes after the sensors detect that the temperature has increased to 45 F 7 2 C or more An additional freeze sensor may be installed to protect the system from special conditions which may lead to its freezing Such a sensor is recommended for spas located in colder climate zones Contact your local dealer for more details Ice Conditions which may cause system freezing have been detected Caution Risk of electric shock The device does not include any parts to be f xed by the user Do not attempt to repair the control system yourself Contact your dealer or service center for help Follow all the user instructions on how to connect the spa to power supply Installation should be performed by an electrician with appropriate qualifications making sure the device is properly grounded 1 6 MASSAGE There are water and air massage systems installed in the bath 1 6 1 Hydromassage whirl bath Hydromassage is the pressure on defined muscles exerting by stream of water or stream of air and water Water or air and water at high pressure bring out from regulated jets and hit on body surface It tones and relaxes the skin at the same time massaging and cleaning it Hydroma
16. helps to keep the bathe clean helps to keep water clean fresh and clear eliminates any unpleasant water smell eliminates fungi and yeast in water refilling with water does not need to be frequent 1 8 1 UV LAMP OPTIONAL A special UV lamp generates UV C radiation with a wavelength of 253 7 nm which neutralizes bacteria viruses and other primitive organisms preventing their reproduction at the same time The benef ts of UV C radiation ensures fresh clean and clear water disinfects water safely and efficiently keeps the formation of mold bacteria and algae under control reduces the use of chorine and other chemicals by up to 80 prevents the smell of chlorine as well as skin and eye irritation including eye redness is more environmentally friendly than traditional methods Ozonation and the UV lamp work only during f Itration 1 9 MARINA SPA FILTRATION SYSTEM SPA MARINA filtration system comprises telescopic skimmer filter an element taking and filtering water fig 1 fig 3 filtration and massage pump water filter with a renewable cartridge for multiple use fig 2 water suction point pipes and PVC piping fig 1 fig 2 fig 3 f Skimmer f Iter with replaceable cartridge maintenance After the bath and its filtration have been turned off take off the acrylic cover above the skimmer filter unscrew the plastic lid of the filter and take out the c
17. ies of intense flashes of varying coloured light Cross fade Colour cycle back and forth gracefully between blue and green Total cycle lasts 1 minute Fixed colour Static display of a single colour Available colours include green and blue Colourful multi point light settings 6 brilliant colors and 4 color transition programs Tidal fade Cool color mix slow transitions between green and blue tones Afterburner Fade Warm color mix slow transitions between red and orange tones Spectrum Slowdance Slow transitions between all six colors Color Burst Fast strobe through all six colors 1 8 WATER OZONIZING Oxygen Ozone O So B The ozonized air has apart from a nice scent many therapeutic and antiseptic properties It greatly helps in keeping the water clean both in the bath and the plant Ozone definitelv supports ain O Ai maintenance hvgiene in the SPA The heated and ozonized or UV light O Xi Bie is pumped into the air duct system underneath the bath Operating only during filtration Ozone producing process Ozone is healthv itis more and more popular in beautv treatment helps to remove lacuni cellulite and wrinkles improves complexion helps to treat varices and skin diseases helps in heart and circulatorv svstem problems soothes problems connected with menopause Why is ozone necessary in SPA it has antiseptic properties
18. llions of bubbles come from the perforated bath bottom actively relaxing the body The bubbles stimulate circulatory system relax muscles and joints Their activity may be compared to a normal hand massage It soothes the nervous and respiratory system and improves metabolism The airmassage system is made of the following elements air channels situated on two levels forming an integral part of the bath topped with a number of openings within the water section of the bath a blower loop protecting against water intrusion into the blower 12 1 7 COLOURFUL LED SPOTLIGHT MULTI POINT LED LIGHT OPTIONAL If the tub is equipped with the multi colour light feature the colour can be changed by switching the light off and on again The light colour changes in a sequence Colourful spotlight settings Slow colour Colours transition gracefully from colour to colour cycling through the entire colour wheel Each colour cycle lasts approximately 3 minutes Fast colour Colours transition from colour to colour cycling through the entire colour wheel Each colour cycle lasts approximately 1 minute Slow random colour Colours step or jump from one colour to the next in random order Each colour duration lasts approximately 10 15 seconds Fast random colour Colours step or jump from one colour to the next in random order Each colour dura tion lasts approximately 5 seconds High speed random colour A rapid ser
19. of the strips should be assembled to the down side of the cabinet The thermal cover has 2 svmetrical parts with the kind of hinge in the middle for easv folding and handling Continous exposition to the sun UV lightning can be the cause of color change of the thermal cover Protect the thermal cover against the mechanical damages 2 times a month is recommended to open the slipcover of the thermal cover for removing the water from it 0 z 17 PART 2 INSTALLATION MANUAL 2 1 TRANSPORT The bath should only be transported in the original manufacturer s packaging After unpacking the bath can be carried by the aluminum frame or acrylic elements The pipes and cables must not be used as handles grips 2 2 SITE PREPARATION The SPA MARINA portable bath may be operated both indoors and outdoors The site for the bath should comply with the following conditions a the proper area and the proper transportation routes in case of closed premises b 230V electrical supply and ensured efficiency of the electrical connection in respect of the equipment the rated power consumption is 5 6 kW and requires use of a 3x4 mm electrical cable as the connection with regard to the safety of the users in all cases the supply cable must be protected by means of a differential current switch with the standard rated switch off current of 30 mA c water supply and drainage 950 d leveled floor floor drain recommended
20. onnected to the B sensor socket does not work The sensors are out of balance If this message and the SPA water temperature are displaved alternatelv such a condition may be temporary If the situation persists the SPA will be turned off Significant water temperature difference is If the water level is normal make sure that all pumps detected by the sensors This may indicate J have been vented If the problem continues contact your flow related problems local dealer or service center If the problem continues contact your local dealer or service center L The problem with low flow persists this message appears after the message has been displaved five times within 24 hours The heater is switched off but the remaining spa functions work as usual Perform the steps which need to be taken when the message is displaved HFL Press anv button to reactivate water heating If the water level is normal make sure all the pumps are Improper water qualitv low flow or air primed The message will disappear automaticallv after bubbles in the heater The spa is switched 15 minutes The alarm is deactivated if any button is off for 15 minutes pressed manuallv If the problem continues contact vour local dealer or service center Improper water quality has been detected Perform the steps which need to be taken when the in the heater this message appears after message is displayed dr The message will not be res
21. s storage or ill treatment breakages damage resulting from the use of water at temperatures of over 50 C wear from abnormal usage or any other cause not stemming from the appliance c if the Spa after use is not secured by thermal cover against sun radiance d if installation has been done by non authorised service or if non original spare parts were used if it is found that the Spa has been in use for a period longer than the warranty period f if used water do not fulfill conditions of DIN 19643 97 as well SIA 173 5 In particular POOLSPA Sp z o o declines all liability for any harm to people or damage to things that may have resulted from any of the excluded causes specified in the preceding section 6 Any other demand stemming from grounds not specified in the above sections is excluded unless the law of the land expressly attributes liability Recommendations Before using the equipment read carefully through the instructions included with the Spa ROCA POLSKA Sp z Zak ad produkcyjny POOLSPA ul Dabskiego 35 72 300 Gryfice tel 48 91 38 777 00 fax 48 91 38 777 01 www poolspa pl e mail info poolspa pl TECHNICAL PRODUCT SHEET MODEL FACTORY NUMBER DATE OF PRODUCTION AND TESTING QUALITY CONTROL NOMINAL POWER REQUIREMENTS FUSING REQUIREMENTS VOLTAGE FREQUENCY THERMAL PROTECTION Marina SPA POOL SPA QUALITY CONTROL 25A 230V AC 50 Hz 23 POOLSP
22. special attention to the non drainable area shaded area in the illustration 2 5 GROUNDING CABLE CONNECTION In order for the residual current device and the tub itself to function properly a grounding cable with a cross section of at least 2 5 must be installed Connect the cable to the frame as illustrated Connect the other end of the cable to the protective grounding of the building s electrical wiring Place of connection of the earthing wire 2 6 CONNECTION TO MAINS As the bathtub is protection class equipment it has to be permanently connected to power supply TN S type using IP X5 junction box It is recommended to install the connection box in area under the bathtub close to other electrical devices of the bathtub more than 20 cm above the floor The bathtub must never be connected using a plug Zone 0 is the area inside the bath Zone 1 is the zone area plus the space up to 2 25 m above the floor Zone 2 is the zone 1 area extended by 0 6 m again up to 2 25 m above the floor Zone 3 is the area reaching 2 4 m beyond zone 2 up to 2 25 cm above the floor Location of protection zones 19 230 V electric connection with 5 6 kW efficiencv protected 3 4 Water connection 1 2 for filling and draining the bath Marina SPA connections All the SPA MARINA hvdromassage components are on the right hand side of the bath To ensure eas
23. ssage is recommended for anybody with spine arthritic or muscle pains respiratory system diseases or gynaecological problems Water massage system hydro massage is made of the following elements a set of 32 water and air jets supplying water or a water and air mix of high kinetic power to the water section of the bath a hydromassage whirl pump enforcing water circulation 2 regulators of air supply to the hydro massage jets installed at the edge of the bath used for regulation of massage intensity water suction point Hydromassage regulation is controlled via an aeration regulator on either side of the control panel The more air the stronger the flow Hydromassage intensity is increased by turning the regulator knobs anti clockwise Hydromassage intensity is decreased by turning the regulator knobs clockwise Z 11 Each of the regulators is responsible for controlling a different jet section fixed mini ozone jet 3 4 black tub drain A fixed mini jets large rotary jets 3 way hydromassage hvdromassage large fixed jets uae aeration D large fixed jets regulators 3 way hydromassage section valve The valve allows switching hydromassage to left right or both sections of the bath Jets activity zone selection Left section Right section Both section 1 6 2 Airmassage pearl bath In air massage heated air is pumped into water by a blower Mi
24. t container and fill to the 10 ml mark with pool water e add 1 DPD 4 tablet to the container and close the plug e shake the container and dissolve the tablet e compare the colour of the solution with the colours in the column on the right side to read the Dinofresh value of the tested water sample e ideal values range from 5 0 to 8 0 mg ilitre Important instructions e do not touch the tablets It may distort the test outcome e reading of results must take place immediately after the tablet has dissolved in water e after each measurement the test container and its lid should be thoroughly rinsed Otherwise it may also distort the results The tablet reagents are provided for the purpose of the above described chemical analyses and should not be used for any other purposes The tablet reagents must not be handled by children a The START SET If the measured pH is outside the range 7 2 to 7 6 it will be necessary to use SP A Marina granules to correct level 1 Dinominus decreasing granules Dosage about 10 g 1000 litre to lower pH by 0 1 in case of MARINA approximately 5 7 g The granules should be poured over water surface as the filtration pump is on The pH measurement should take place directly after the correction Do not add the granules anywhere close to the skimmer 2 Dinofresh active oxygen granules should be added to the skimmer Dosage 25 4 1 is a start value 15 g for MARINA and
25. then in 5g doses to restore the Dinofresh level to5 8 mg l 3 Dinoclean S alkaline liquid and strong chemical to clean the rim of the bath and dissolve fats It is perfect to clean any greasy stains from the walls or the rim of the bath and to remove calciferous deposits Dosage spread concentrated or dissolved 1 10 agent on dirty surfaces using a brush Rinse thoroughly after a short period of time Do not let the agent dry before rinsing A set of disinfecting agents for MARINA SPA can be purchased at your sales agent It is a natural phenomenon that in SP A baths the pH value of water tends to increase However very rarely the pH value decrease can be observed It is then recommended to use Dinoplus granules which can be ordered through the showroom of the Marina SPA manufacturer Set of measurement treatment agents to be purchased at sales showrooms 16 1 12 THERMAL COVER ADDITIONAL OPTIONAL The SPA MARINA can be optionally provided with a thermal cover When is it necessary to have a thermal cover when the bath is going to be used outdoors i e in a garden the cover prevents the water from excessive cooling down and keeps the bath clean when the bath is going to be used very frequently indoors the cover serves to prevent the water from excessive evaporation keep the cover on place no matter of the weather conditions there are 4 tie down strips with buckle lock Metalic ends
26. ual current device periodically according to the guidelines for testing and resetting such devices A differential current switch with an indicated test button The SPA tub should be connected to the building s electrical wiring permanently The electrical wiring should be equipped with the appropriate manual cut off mechanism enabling the opening of contacts on each power supply pole In addition equipotential bondings must be made using the clamp located on the tub support frame The minimum cross section of the equalizer power cord is 4 mm 18 All electrical connections should be made by a qualif ed electrician For safety reasons check the effectiveness of the anti electric shock protection from time to time by pressing the TEST button on the residual current device If the power is not turned off immediately after pressing the button unplug the tub manually and contact a qualif ed specialist Do not use the SPA tub if the protections do not function properly BATH FILLING AND DRAINAGE Marina Spa is equipped with 1 2 connector to fill the bathtub f and drain water f It recommended for the spa to be connected to the sewage i drain when being filled with water ON 99 gt D MW Om Manually remove water from the indicated area in the bathtub 89 e g bv using a small bucket 4 a e Once the bathtub is empty shut off power supply to the bathtub L When emptying pay
27. v access to them the right side of the bath should not be encased 2 7 SERVICE VALVE In Marina SPA there are two gate valves which shut off the water supply to the pump and heater If valves are closed they provide overhaul repair or even replacement of equipment in a spa filled with water Before f rst use of spa please check whether all valves are open 2 8 MAINTENANCE OF ACRYLIC ELEMENTS Only mild fluids not containing acetone abrasive or caustic substances should be used to clean the bath The structure and low level of surface adhesion of acrylic mean that keeping the bath clean should not be a problem Mechanically damaged gloss acrylic small shallow scratches can be easily repaired In the case of small scratches a small amount of wax free car polish should be used Deeper scratches may be removed by sandpaper in order of grain 800 1200 2000 followed by the car polish mentioned earlier In order for the surface to be smooth it should be ground in a circular motion followed by a wax car polish which provides a high level of shine Repairs can be made with a repair kit available at the dealer shops however we recommend using the services of our authorized POOLSPA service staff The repair kit 20 21 WARRANTV FOR SPA Our company POOLSPA Sp z 0 0 guarantees its products against all manufacturing or operational defects under the conditions set out here After installing the Spa
28. ylinderlike cartridge The cartridge should be cleaned with a soft brush and warm water Then all the elements should be installed again in the opposite order and the bath may be switched on again 14 Filtration and massage flow first and second speed Telescopic skimmer filter li Il Additional flow Filtration first soeed only second speed through a pressure valve Hydromassage second speed Return flow first and second speed 1 10 DISINFECTION Disinfection process in the SPA Marina is ozone based Ozone is used during filtration Additionally the bath is equipped with a START SET for pH correction and disinfection with active oxygen as described in Part 1 11 1 11 MEASUREMENT AND TREATMENT FORMULA SET Before the first bath and always once in 2 weeks please check the water pH with the enclosed Dinofresh pH Tester pH measurement e rinse test container and fill to the 10 ml mark with pool water e add 1 PHENOLRED tablet to the container and close the plug e shake the container and dissolve the tablet e compare the test water color with the colors in the left row e ideal values range from 7 2 to 7 6 e all pH values below 6 8 make the water turn yellow e all pH values above 8 2 make the water turn red Dinofresh measurement This is a measurement of the active oxygen concentration contents informing about the oxygen contents level in water e rinse tes
Download Pdf Manuals
Related Search