Radiator Thermostat Valve - Eco
Contents
1. heater Valve stroke is too short Motor movement is not possible www go green nl Art nr gtd7010341 Adapt again see Adapting Move the valve stem several times by hand it may be that adaptation is impossible because your valve is calcified or the seat no longer performs its function Adjust the water temperature of the boiler water Remove the Go Green Radiator Thermostat Valve move the valve stem back and forth per hand or with a tool Is the installation OK Install the product to the heater Open and close the valve several times manually or replace the batteries Does the valve stem move freely2. function If the temperature drops below 6 C Go Green Radiator Thermostat Valve opens the valve until the temperature again rises above 8 C This prevents the radiators from freezing Calcification protection To prevent radiator valves from calcifying Go Green Radiator Thermostat Valve is submitted to a calcification protection programme once a week on Friday mornings Cleaning and used devices Cleaning To clean the Go Green Radiator Thermostat Valve use only a dry or lightly wet cloth Avoid chemical solvent it can probably damage the device Used devices Do not throw old devices and packaging into the household waste They can be recycled You receive further local government Adapters Heimeier Junkers Landys Gyr MNG Honeywell Braukmann thread measure dimension of M 30x1 5 Danfoss RAV accompanying pin must be plugged on the valve tapped Danfoss RA Danfoss RAVL Help information at your no adapter required accompanying pin only for RAV Batteries do not Replace batteries have enough power Valve does not close completely It may be that the closing point of your valve seat has shifted Heating element does not cool down Is the boiler water temperature OK Heating element does not warm up Valve does not open is it calcified after the summer pause heating pause No adaptation possible Go Green Radiator Thermostat Valve not installed to the
3. of the items with the selector wheel With you can select one menu item and with the selection wheel they can be adjusted The button confirms the setting The button leads to the previous level MODE to select the mode AUTO automatic mode MANU manual mode PROG setting of time programme TEMP setting of comfort and economy temperature ZEIT setting of date and time FENS window function RES reset of the device to factory preset ADAP starting of a new adaptation to adjust the valve URLA travel function INST installation function OFFS adaptation of temperature to the room situation Inserting replacing batteries In order to open the battery compartment please push at the marked positions to remove the cover Then insert the batteries as shown in the illustration Do not use accumulators Ensure that the polarity is correct Attention e Never recharge batteries danger of explosion e Do not short circuit batteries e Do not disassemble batteries e Take low batteries out of the device immediately e Keep batteries away from extreme warming danger of leakage e Do not apply used and new batteries together If needed clean the battery and the contacts before using them e Keep the batteries away from children e When getting in touch with battery acid instantly irrigate the affected parts with clear water and call a doctor Setting date and time After inserting
4. the travel function date of the recommencement of the regular heating times Confirm with ok Set the time and confirm with the button The signal AUS appears on the display Now set the temperature and confirm with ok _ Suitcase symbol appears on the display With the function can be activated Child lock You can lock Go Green Radiator Thermostat Valve to protect the device from unauthorized activation Press the buttons and at the same time for about 2 seconds until the symbol amp appears on the display in order to lock the device By using this button combination again the symbol disappears and you release the lock Heating pause Closing the Go Green Radiator Thermostat Valve Press Select the menu item MODE with the selector wheel Confirm with Select MANI and confirm with Set the temperature on the display to ALS The valve is now closed and will work with a time programme The calcification protection function remains active once a week After the heating pause you switch in the menu to the AUTO mode and the personally set programme will be executed again Going back to factory preset All reset Press Select the menu item RES with the selector wheel Confirm with ok OK flashes confirm with Go Green Radiator Thermostat Valve is reset again Now proceed as described for the initial operation Freeze protection and calcification protection function are active automatically Freeze protection
5. NZ AEN Radiator Thermostat Valve Please read the user manual before you place the thermostat Keep the documents for later questions and provide them if you pass the thermostat on to other persons In this packing e Go Green Radiator Thermostat Valve energy saving radiator thermostat e User manual e Connector e 3 Adapters Application as directed By purchasing the Go Green Radiator Thermostat Valve energysaving radiator thermostat you own a program mable radiator thermostat which can be used for temperature regulations in enclosed rooms andtherefore it can contribute to the reduction of heating energy Please use the thermostat only for this purpose The programming port is intended ONLY for our programming stick Never connect other devices with the programming port Display and control elements Heating times Child lock active 3 Battery low 4a Travel function 1 2 3 mot 6 I t 118 1 1 2 PEC CEE E EEE EE Dr ble bi py 4b Comfort temperature Mw MV M NG a tte ALUN IA Cc ee temperature 4d Window freeze 3 protection function active 5 AUTO or MANU mode active 6a Button meNu leads to the main menu starting from regular display within the menu one keypress leads to the previous level 6b Button _ok _ confirmation of setting 6c Button _ timer function 7 Selector wheel Set up menu By pressing you will arrive at the set up menu Please choose one
6. gramme has been deactivated is shown Confirm with Now the desired temperature can be set Confirm with Offset If the perceived temperature significantly differs from the set thermostat temperature a temperature set up can be executed Press Select the menu item OFFS with the selector wheel Confirm with The degree setting 4 GF will flash on the display Now set up the desired adaptation for the temperature from 5 up to 5 C with the selector wheel Confirm your entry with The temperature display does not change Window function If you open a window and consequently the temperature drops significantly Go Green Radiator Thermostat Valve will automatically close the heating valve in order to save energy The display will show amp Afterwards Go Green Radiator Thermostat Valve will resume normal operation For the set up select FENS in the menu Confirm with First the sensibility is selected with the selector wheel IGH high sensibility MID medum sensibility factory preset 1 ait low sensibility Confirm with Now you enter the time 10min factory preset 60 min for which the valve should remain closed Confirm with Travel function For the time you are absent you can select an individual temperature After this period the originally defined programme becomes active again Press Select the menu item URLA Confirm with Suitcase symbol CD appears on the display Select with the selector wheel the end of
7. hat has been set comfort temperature factory preset 21 C economy temperature factory preset 16 C The heating and economy times can be specified via the adjustable time programme It is possible to set 8 switch points 4 heating and 4 economy times per day at the most Go Green Radiator Thermostat Valve the following factory preset Heating time Heating with comfort temperature factory preset First heating time at 07 00 Economy time lowering to economy temperature factory preset First economy time at 22 00 Setting heating and economy times With Go Green Radiator Thermostat Valve it is possible to set 4 heating and 4 economy times per day one for each day or one for a block of several days TAG1 to TAG7 represent the weekdays from Monday to Sunday Additionally the corresponding days are shown as abbreviation below the menu bar on the display Block construction T1 5 same programme from Monday to Friday T1 6 same programme from Monday to Saturday T1 7 same programme from Monday to Sunday For non programmed days the factory preset remains active Setting of an individual programme Press Select the menu item PROG with the selector wheel Press TAG for Monday is shown on the display Select day block with the selector wheel Confirm with Set the beginning of the first heating time symbol with the selector wheel Confirm with Set the beginning of the first economy time s
8. nnector until it noticeably clicks into place In case of a later installation please switch in the menu to N amp 7 before you install the device Herewith the installation is facilitated Dismounting In order to dismount Go Green Radiator Thermostat Valve press the releasing device to loosen the locking device Now pull the Go Green Radiator Thermostat Valve off of the valve Adaptation Initial installation Press the button until ADAP appears on the display so that Go Green Radiator Thermostat Valve will be able to start its adaptation The device will adapt itself to the stroke of your valve body To do this the valve will now be opened and closed several times to store the end points In some cases this process can take a few minutes After successful adaptation it returns to normal mode Should adaptation become necessary again e g if your radiator does not cool down in the ALI Position please press in the menu the button ADAP until adaptation starts again If the mistake Eg is shown on the display place Go Green Radiator Thermostat Valve onto the radiator valve and then take the batteries out for a short time in order to execute a reset Basic operating modes MANU mode In the MANU mode Go Green Radiator Thermostat Valve adjusts to the manually specified temperature AUTO mode In the AUTO mode Go Green Radiator Thermostat Valve changes between to temperatures according to the time programme t
9. the batteries for the first time the date will flash on the display Now date and time can be set Set date with the selector wheel Confirm with Set month with the selector wheel Confirm with Set day with the selector wheel Confirm with Set hour with the selector wheel Confirm with Set minute with the selector wheel Confirm with That s it On the display PREP will be shown Now the motor will completely move to the installation position in order to make the installation easier As soon as Go Green Radiator Thermostat Valve is ready for installation NST will be shown on the display You can also set date and time via the menu item ZEIT later on But in case of that Go Green Radiator Thermostat Valve does not move to the installation position In case of replacing batteries the stored time programme will remain active You should check the specified time to ensure that Installation Go Green Radiator Thermostat Valve can be quickly and easily mounted on all common valves see adapter table It can be installed without grime and water spots because the heating circuit is not interrupted 1 Turn the manual thermostat head up completely loosen the fastening and pull the thermostat off of the valve 2 Use an appropriate adapter if required and push it onto the valve Screw the connector on the valve or the adapter Now you put Go Green Radiator Thermostat Valve on the co
10. ymbol with the selector wheel Confirm with Now if desired a second third or fourth heating economy time can be entered If you do not want to set a further heating economy time confirm L with The next day for programming is shown on the display If you do not want to enter a further day leave the menu with If the temperature is shown on the display the programming is finished Within the blocks you can also overwrite single days with different times Setting comfort and economy temperature Press menu Select the menu item TEMP with the selector wheel Confirm with oK Set comfort temperature with the selector wheel Confirm with Set the economy temperature with the selector wheel Confirm with Area AUS 8 C freeze protection function is active AreaE N valve is completely open Remark Maximum energy saving can be obtained with an economy temperature which is about 5 C below the comfort temperature Manual operation With the selector wheel an adaptation of the room temperature is possible at any time In the AUTO mode it remains active until the next switch point is reached Now the usual programme becomes active again Further functions The timer function is selected with the timer button With this function a user defined temperature for a programmable period can be entered This can be very useful in case of a party for example Press First the time for which the time pro
Download Pdf Manuals
Related Search