Home

EAD(CB)SF

1. EAD CB SF has restrictions on the types of PCs and boards that can be used Be sure to check the following restrictions before use lt Restrictions of PC gt Your PC must have a PC Card slot conforming to the CardBus PC Card Standard on a PC _EAD CB SF uses the switch fabric to extend the bus The expansion adapter does not work normally if the BIOS and CardBus controller on your PC do not detect the switch fabric device as the PCI to PCI Bridge Check the CONTEC s Web site for more information on the certified PCs and supported OSs lt Restrictions on transfer rate gt When the expansion chassis accommodates a board that performs high speed transfer such as bus mastering the overall transfer rate may be lower than that of PCI bus slots in the main unit of a desktop PC This is caused by bus extension by the PCI to PCI Bridge The transfer rate may vary with the system configuration and the type of the PC lt Restrictions of PCI board gt None of the following types of boards can be used in any expansion slot in the expansion chassis connected to the EAD CB SF Video display board VGA board Board that must boot from within the expansion chassis Board to connect a PCI bus expansion chassis Board explicitly stated not to be used with the PCI to PCI Bridge Some boards even PCI compliant ones may not work depending on their specifications lt Restrictions of OS gt The EAD CB SF has the followi
2. Installing EAD CB driver Step Card bus controler setting Done Step2 PCI PCI bridge 1 setting Done Step3 PCI PCI bridge 2 setting DIT Setup in process Installing EAD CB driver 3 i The driver installed completely Click OK then open Device Manager Pressing OK invokes Device Manager 5 When the PC Card and expansion chassis has been detected normally PCI boards are detected next The PCI boards installed on the expansion chassis are detected in sequence For setting up and checking the boards used on the expansion chassis refer to their respective manuals CONTEC EAD CB SF 21 2 Setup Checking the hardware You can use Device Manager to check whether the expansion chassis has been identified in Windows Device Manager shows PCI standard PCI to PCI bridge under System devices Make sure that two entries of PCI standard PCI to PCI bridge are listed Device Manager File Action View Help e 4284 System devices 1 ACPI Lid 19 ACPI Power Button 1 ACPI Sleep Button ACPI Thermal Zone p Direct memory access controller 19 Intel R 82801BAM CAM PCI Bridge 2448 4 Intel R 82801CAM LPC Interface Controller 248C p Intel R 82845 Processor to AGP Controller 4 Intel R 82845 Processor to I O Controller 1430 i ISAPNP Read Data Port p Microcode Update Device p Microsoft ACPI Compliant System p Microsoft Composite Battery 3 Numeric data proce
3. 27 EAD CB SF User s Manual CONTEC CO LTD December 2005 Edition 3 9 31 Himesato Nishiyodogawa ku Osaka 555 0025 Japan Japanese http www contec co jp English http www contec com Chinese _http www contec com cn No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD 12212005 04212004 Management No A 46 851 12212005 _rev2 PartsNo LYDK321
4. 4Slots ECH PCI SF H4B PCI Bus Expansion Chassis Long x 4Slots ECH PCI SF F4B PCI Bus Expansion Chassis Short x 4Slots ECH PCI SF H4A Check the CONTEC s Web site for more information on these expansion chassis Connection cable Option Connection cables 12 meter STP category 5e straight cables are bundled with this product The following options can also be available UTP category Se straight cables 3m TP 03 1 2 UTP category Se straight cables 5m TP 05 1 2 UTP category Se straight cables 10m TP 10 1 2 1 A pair of cables are required for connection 2 When used in an environment susceptible to extraneous noise UTP cables may cause link connection It is advisable to use STP cables available on the market CONTEC EAD CB SF 1 1 Before Using the Product Combinations of Expansion Adapters and Expansion Chassis The expansion adapters and expansion chassis can be used in the following combinations Expansion Expansion chassis ECH PCI SF adapter EAD CB SF o oO oO oO o x x x x eanes o o o o o o olo Expansion chassis ECH PCI SF H2B ECH PCI SF F 2B ECH PCI SF H4B ECH PCI SF F 4B A f mi A i Fs ess il amp 1 i ie ECH PCI SF H4A ECH PCI SF H7A ECH PCI SF F 7A 2 Pad HEL tiny gt 7 LUTT a WAN ef ECH PCI SF H13A ECH PCI SF F13A Expansion adapter i EAD LPCI SF CONTEC 2 EAD CB SF 1 Before Using the Product Restrictions
5. CB SF has been installed correctly Make sure that the connection cable has been installed correctly When connecting the connection cable to the main chassis insert the connector until it clicks into place ECH PCI SF H 2B F 2B H 4B F 4B EAD CB SF ECH PCI SF H4A Make sure that the POWER LED on the expansion chassis is turned on Make sure that the LED LINK built in the RJ 45 connector is on When used in an environment susceptible to extraneous noise UTP cables may cause link connection It is advisable to use STP cables available on the market The photo is of the EAD CB SF CH PCI SF H2B but the check points are the same as with the ECH PCI SF F 2B H4B F 4B F 4A EAD CB SF 25 2 Setup Setup cannot be done under Windows XP or Windows 2000 j Refer to Troubleshooting on the bundled CD ROM CONTEC 26 EAD CB SF 3 About Hardware Hardware specification Table 3 1 Specification of BUS PC CB SF Item Specification Compatible PC card slot PC Card Standard compliant CardBus Outside dimensions mm TYPE II 119 0 x 54 0 x 19 0mm Power consumption Max 3 3VDC 450mA 1 Usable condition 0 50 C 20 90 RH No condensation Weight 1 Power is supplied from the PC s main unit Table 3 2 Specification of the bundled cable Specification Bundled connection cable STP category 5e straight cables 12m x 2 cables Weight 400g cable 3 About Hardware CONTEC EAD CB SF
6. Expansion chassis One of the chassis c AC adapter d Power cable e PCI board to be installed The photo is of the EAD CB SF CH PCI SF H2B CAUTION When used in an environment susceptible to extraneous noise UTP cables may cause link connection It is advisable to use STP cables available on the market Getting ready with your PC The PC Card BUS PC CB SF is conforming to the CardBus PC Card Standard Make sure that your PC has a TYPE II PC Card slot conforming to the CardBus PC Card Standard 10 CONTEC EAD CB SF 2 Setup Names of major parts BUS PC CB SF LINK LED for RX LINK LED for TX Figure 2 2 Names of major parts lt BUS PC CB SF gt LINK LED The LINK LEDs show whether the switch fabric device is working normally Both of the TX and RX LEDs remain on when the device is working normally If they are blinking or off see Setup Troubleshooting Step 2 Installing the Expansion Board Refer to the user s manual for the expansion chassis to install the expansion board on the expansion chassis CONTEC EAD CB SF 11 2 Setup Step 3 Connecting the Cable Connecting the connection cable to the PC Card Connect the RJ 45 connector of connection cable to the PC Card BUS PC CB SF Connect them together with the connector s flat side and PC Card s front surface face up as shown in Figure 2 3 below Make sure that the connection cable connec
7. PC HELPER PCI Bus Expansion Adapter for CardBus PC Slot EAD CB SF User s Manual CONTEC CO LTD Check Your Package Thank you for purchasing the CONTEC product The product consists of the items listed below Check with the following list that your package is complete If you discover damaged or missing items contact your retailer Product Configuration List PC Card BUS PC CB SF 1 Connection cable STP category Se straight cables 12m 2 User s Manual this booklet 1 CD ROM DriversSoftware for EAD CB Series 1 i PC Card CONTEC o Connection cable User s Manual CD ROM Drivers Software for EAD CB Series User s Manual EAD CB SF Copyright Copyright 2004 CONTEC CO LTD ALL RIGHTS RESERVED No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD CONTEC CO LTD makes no commitment to update or keep current the information contained in this document The information in this document is subject to change without notice All relevant issues have been considered in the preparation of this document Should you notice an omission or any questionable item in this document please feel free to notify CONTEC CO LTD Regardless of the foregoing statement CONTEC assumes no responsibility for any errors that may appear in this document or for resul
8. R DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury or in property damage CONTEC EAD CB SF 5 1 Before Using the Product Handling Precautions AN AN DANGER Do not use the product where it is exposed to flammable or corrosive gas Doing so may result in an explosion fire electric shock or failure AN CAUTION The PC Card BUS PC CB SF must be plugged into a PC Card slot conforming to the CardBus PC Card Standard on a PC Do not impact or bend the PC Card BUS PC CB SF Doing so may result in a malfunction overheating fault or damage Do not plug or unplug any board into or from the expansion slot with the PC or expansion chassis powered Doing so may result in a malfunction overheating fault Be sure to turn off the PC or expansion chassis and unplug their power cables before plugging or unplugging any expansion board Do not plug or unplug any PC Card BUS PC CB SF into or from the Card slot with the PC or expansion chassis powered Do not plug or unplug the cable interconnecting the PC Card BUS PC CB SF and the expansion chassis with the PC or expansion chassis powered Do not use or stor
9. e connector plugged Do not apply excessive force to the connector of the PC Card for example by forcing the connection cable connector off the PC Card Do not place anything on the connection cable connector CONTEC 14 EAD CB SF 2 Setup Notes on use of two or more PC Cards If your PC has a stack of two TYPE II PC Card slots two BUS PC CB SF PC Cards cannot be used simultaneously in both slots This is due to the shape of BUS PC CB SF The PC Card BUS PC CB SF can be used along with another PC Card which does not use any external connector such as a memory card BUS PC CB SF BUS PC CB SF p BUS PC CB SF QO BUS PC CB SF O BUS PC CB SF BUS PC CB SF _ H Figure 2 6 Notes on use of two or more PC Cards BUS PC CB SF CONTEC EAD CB SF 15 2 Se tup Step 5 Setup and Check Starting the system The expansion chassis is turned on and off in sync with the PC s power supply When the PC detects the PC Card BUS PC CB SF the expansion chassis is turned on Turning on the system 1 2 3 4 Plug the power code of the expansion chassis into a wall outlet You do not need to press the POWER switch on the front panel 1 The power supply of a PC is turned ON When the PC Card is detected by the OS the expansion chassis is turned on Make sure that the POWER LED on the expansion chassis and the LINK LED on the RJ 45 conn
10. e rae e SeN eE e aaee EASE EEEE OETA Aaa 6 EMVinOnime nts nee a E RER E TE REER AR R E EREE RERE OEA 7 TSP Canes ees EAS SESSE SEEE E PESEE 7 StOPa gene E A E near E EE wl pein E O E Nesp duanvousene 7 IDEES aO T I P EEE A E E T pA SETUP 9 What is Setup n E K EAE R ERR RARER R ORRERI O RE 9 St p 1 Pr paration seseo a aa e A R ada iets Race O EE E ei 9 Items t be prepated cisccscsssseceyecicbieceevs sens cdisess on RE EEE suse EER PIPPE EE PEPEES K asst EEI TIY 0 Names oftiiaj Ot Parise a aa a aa a a aaa aa ay 1 Step 2 Installing the Expansion Board 0 cccccceseeseesseseesecesceseeseeseesecsececeseeaeeseesecsecneceeeeseeaeeaeeaeenees 1 Step 3 Connecting the Cable sic areara a E R ERAR RERE E R oan dave 2 Connecting the connection cable to the PC Card oo ccceeseeseeeeseeeeseesceesseeeesesseeesseeeeaees 12 Connecting the connection cable to the Expansion Chassis 0 cccccceeseeseeeeeeeeseeeeeeeseeeeaees 3 Plugeinig the Power Cable ernis n n EA RRR R E HEA EEN 3 Step 4 Plugging the PE Caid eh n A A aaa a ge tales a a aaa ad 4 Notes on use of two or more PC Cards wo ececcecceeseeeseeseesecescseeseescsecaeeesseeeeseeseeesseeseesaeeeeaes 15 CONTEC iv EAD CB SF Step Setup and Checks sis Saas Se et ein Bet ines stad eames cated eran aac ea 16 Starting the system 16 For use under Windows XP Windows 2000 cic eceoisccccccssveutioeessacveaeensds asc ollsoveesacs susteblavedioncees 17 Setup the Add Ne
11. e the board where it is exposed to any chemical either directly or as vapor in the air The specifications of this product are subject to change without notice for enhancement or quality improvement Even when using the product continuously be sure to read the manual and understand the contents Do not modify this product CONTEC will bear no responsibility for any problems etc resulting from modifying the product Regardless of the foregoing statements CONTEC is not liable for any damages whatsoever including damages for loss of business profits arising out of the use of or inability to use this CONTEC product or the information contained herein CONTEC EAD CB SF 1 Before Using the Product Environment Use this product in the following environment If used in an unauthorized environment the board may overheat malfunction or cause a failure Operating temperature 0 50 C Humidity 20 90 RH No condensation Corrosive gases None Floating dust particles Not to be excessive Inspection Inspect the product periodically as follows to use it safely The gold plated leads of the bus connector have no stain or corrosion Check that the bus connector and its cable have been plugged correctly Storage When storing this product keep it in its original packing form 1 Put the PC Card in the storage bag 2 Wrap it in the packing material then put it in the box 3 Sto
12. ector is on Turning off the system 1 2 A The power supply of a PC is turned OFF The expansion chassis is turned off in synchronization with the PC s power supply Pressing the POWER switch on the front panel of the expansion chassis turns on the expansion chassis or puts it to sleep Use the switch for example to turn on only the expansion chassis CAUTION Do not turn on or off the expansion chassis with the PC main unit powered Doing so cancels the detection of the bus adapter When turning the expansion chassis on back restart the PC main unit Do not plug or unplug the PC card with the PC main unit powered Do not plug or unplug any board into or from the expansion slot with the PC or expansion chassis powered Doing so may result in a malfunction overheating fault Be sure to turn off the PC or expansion chassis and unplug their power cables before plugging or unplugging any expansion board If you turn on the PC after turning it off keep a time interval of at least 10 seconds in between If the power OFF to ON interval is too short the expansion chassis may fail to be turned on 16 CONTEC EAD CB SF 2 Setup For use under Windows XP Windows 2000 Setting up the hardware The switch fabric devices used for the expansion adapter and expansion chassis are detected as a PCI to PCI Bridge and another PCI Bridge device in sequence upon startup of Windows For use under Windows XP or W
13. eted Close running applications before installation To install the driver you must have administrator privileges 1 Make sure that the PC Card and expansion chassis have been connected correctly the PCI board to be used has been installed on the expansion chassis correctly and that the expansion chassis power cable has been plugged into a wall outlet 2 Shut down Windows insert the PC Card into the CardBus slot then start Windows Although Windows will prompt you to restart the system do not restart it 3 Load the bundled CD ROM on the CD ROM driver Invoke Explorer and run the installer CCBSETUP EXE 4 Follow the on screen instructions to proceed to install the driver You need to restart the system later prompted by the installed Installing EAD CB driver i Installing the EAD CB driver Please save your work and then close all applications before continuing Press OK to proceed Installing EAD CB driver Step1 Card bus controler setting Step2 PCI PCI bridge 1 setting Step3 PCI PCI bridge 2 setting Setup in process CONTEC EAD CB SF 19 2 Setup Installing EAD CB driver You must restart Windows before continue to next step i Step1 and 2 was completed Click OK then restart the computer Cancel Press OK to restart Windows Installing EAD CB driver The Device Manager will shown Db IF new PCI bridge is shown on Device Manager click OK the
14. f Plugging the Power Cable 1 Connect the power cable to the expansion chassis CAUTION Do not plug or unplug any board into or from the expansion slot with the PC or expansion chassis powered Doing so may result in a malfunction overheating fault Be sure to turn off the PC or expansion chassis and unplug their power cables before plugging or unplugging any expansion board CONTEC EAD CB SF 13 2 Setup Step 4 Plugging the PC Card Make sure that the PC is off and that the AC adapter is already connected then plug the PC Card BUS PC CB SF into the PC Card slot in the PC Check the direction of the arrow mark VW on the PC Card and fit it well into the PC Card slot as shown in Figure 2 5 Although the PC Card has an accidental insertion preventive groove inserting the PC Card forcibly can break the slot and the Card Note also that the PC Card slot on some PCs requires that the PC Card be inserted with the front side face down Make sure before inserting the PC Card For notes on unplugging the PC Card refer to the manual for your PC Figure 2 5 Plugging the PC Card CAUTION Take the following precautions not to break the PC Card or not to cause its connector to break or come loose Do not insert the PC Card in reserve or by a procedure other than specified Do not insert the PC card while holding the connection cable or its connector Do not move the PC with the connection cabl
15. indows 2000 the dedicated driver software must be installed Refer to Readmej html on the bundled CD ROM as well Setup the Add New Hardware Wizard 1 The Add New Hardware Wizard will be started Select Install from a list or specific location Advanced then click on the Next button Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for CONTEC Co Ltd EAD CBISF A If your hardware came with an installation CD lt gt or floppy disk insert it now What do you want the wizard to do O Install the software automatically Recommended lt Click Next to continue CONTEC EAD CB SF 17 2 Setup 2 Select the Inf folder in the bundled CD ROM and then click on the OK button Browse For Folder Select the folder that contains drivers for your hardware Se WINXPU G Se WORK H Bh cance 1 Help Oa wings winzooo To view any subfolders click a plus sign above 3 Complete the Found New Hardware Wizard Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for PE CONTEC Co Ltd EAD CB SF T Click Finish to close the wizard 18 CONTEC EAD CB SF 2 Setup Installation Follow the procedure below to install the driver The system must be restarted twice before the installation process can be compl
16. m which it was purchased This warranty is not applicable for scratches or normal wear but only for the electronic circuitry and original products The warranty is not applicable if the device has been tampered with or damaged through abuse mistreatment neglect or unreasonable use or if the original invoice is not included in which case repairs will be considered beyond the warranty policy How to Obtain Service For replacement or repair return the device freight prepaid with a copy of the original invoice Please obtain a Return Merchandise Authorization number RMA from the CONTEC group office where you purchased before returning any product No product will be accepted by CONTEC group without the RMA number Liability The obligation of the warrantor is solely to repair or replace the product In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage misuse or malfunction of this device CONTEC 4 EAD CB SF 1 Before Using the Product Safety Precautions Understand the following definitions and precautions to use the product safely Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources Understand the meanings of these labels to operate the equipment safely A DANGE
17. n continue to Step3 The above dialog box appears when Windows has been started Check Device Manager to make sure that the PCI to PCI bridge has been detected then click on OK to proceed Device Manager lt 4 amp 6 2 8 DER File Action Yiew Help iy System devices a ACPI Lid 1 ACPI Power Button ig ACPI Sleep Button 1 ACPI Thermal Zone 4 CONTEC Co Ltd EAD CB SF 4 Direct memory access controller p Intel R 82801B4M CAM PCI Bridge 2448 p Intel R 82801CAM LPC Interface Controller 248C 4 Intel R 82845 Processor to AGP Controller p Intel R 82845 Processor to I O Controller 1430 ig ISAPNP Read Data Port 9 Microcode Update Device 19 Microsoft ACPI Compliant System 4 Microsoft Composite Battery i Numeric data processor PcLb PCI standard PCI to PCI bridge 9 Plug and Play Software Device Enumerator 19 Programmable interrupt controller 1 System board Take Step 3 after checking PCI to PCI Bridge You need to take Step 3 after a new PCI to PCI bridge has been detected by the OS Press OK after the PCI to PCI bridge is displayed in the system tray or Device Manager If you press OK before it is displayed Step 3 will be executed after restart Installing EAD CB driver L You need to restart Windows to finished this installation completely Press OK to restart Windows CONTEC 20 EAD CB SF 2 Setup
18. ng restrictions when used in the Windows XP or Windows 2000 environment Available I O address range Within 768 Bytes Available memory address range Within 1 MByte The available I O address and memory address ranges may be different depending on each PC environment CONTEC EAD CB SF 3 1 Before Using the Product Customer Support CONTEC provides the following support services for you to use CONTEC products more efficiently and comfortably Web Site Japanese _http www contec co jp English http www contec com Chinese http www contec com cn Latest product information CONTEC provides up to date information on products CONTEC also provides product manuals and various technical documents in the PDF Free download You can download updated driver software and differential files as well as sample programs available in several languages Note For product information Contact your retailer if you have any technical question about a CONTEC product or need its price delivery time or estimate information Limited Three Years Warranty CONTEC products are warranted by CONTEC CO LTD to be free from defects in material and workmanship for up to three years from the date of purchase by the original purchaser Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office fro
19. re the package at room temperature at a place free from direct sunlight moisture shock vibration magnetism and static electricity Disposal When disposing of the product follow the disposal procedures stipulated under the relevant laws and municipal ordinances CONTEC EAD CB SF 7 1 Before Using the Product CONTEC 8 EAD CB SF 2 Setup 2 Setup This chapter explains how to set up the board Refer to the user s manual for the expansion chassis as required What is Setup Setup means a series of steps to take before the product can be used Taking the following steps in this chapter sets up the EAD CB SF Step 1 Preparation Step 2 Installing the Expansion Board Step 3 Connecting the Cable Step 4 Plugging the PC Card Step 5 Setup and Check If setup fails to be performed correctly refer to Setup Troubleshooting Step 1 Preparation Configuration image The photo is of the EAD CB SF CH PCI SF H2B Figure 2 1 Configuration image CONTEC EAD CB SF 9 2 Setup Items to be prepared PC Expansion adapter This product The expansion adapter consists of a PC card to be plugged on a PC and connection cables A CD ROM is bundled with the product PC card to be plugged on a PC BUS PC CB SF a Connection Cable b The connection cables can be substituted for by UTP or STP category Se straight cables of up to 12m in length CD ROM DriversSoftware for EAD CB Series
20. ssor PCI standard PCI to PCI bridge PCI standard PCI to PCI bridge Plug and Fe Device Enumerator Programmable interrupt controller System board Figure 2 7 Sample screen shot of Device Manager CONTEC 22 EAD CB SF 2 Setup Setting Utility The EAD CB Driver setting utility WIN2000 CCBUTIL EXE is a utility that changes settings for the EAD CB driver in the Windows XP or Windows 2000 environment Use this utility when the CardBus controller PCI to PCI bridge and PCI boards are not identified correctly with the driver s default parameters set at installation Function overview The EAD CB driver is the utility to adjust the sizes of the I O address and memory address windows set by Windows for the CardBus controller and PCI to PCI bridge Note on using this utility When the CardBus controller or PCI to PCI bridge is marked with an exclamation mark due to a code 12 error in Device Manager or causes the blue screen of death upon startup of Windows usually the I O address window range may be inappropriate This utility allows you to change the operation parameters for the EAD CB device driver The changes made to parameter settings take effect the next time Windows is restarted In most cases you can work around the problem by lowering the I O address window range from a default of 768 to 512 or to 256 4 EAD CB Driver setting utility Resource settings VO address window Memory address windo
21. tors are locked CAUTION When connecting the connection cable with the PC Card align their mating connectors and plug them straight into each other Applying excessive force to the cable side connector of the PC Card may break or make it loose Do not plug or unplug connector with the PC powered Doing so may result in a malfunction When used in an environment susceptible to extraneous noise UTP cables may cause link connection It is advisable to use STP cables available on the market The PC may malfunction if link disconnection occurs with the LINK LED blinking or off Connection Cable BA Dy PC Card PC Card slot side Figure 2 3 Connecting the connection cable to the PC Card CONTEC 12 EAD CB SF 2 Setup Connecting the connection cable to the Expansion Chassis Refer to the user s manual for the expansion chassis to connect its connection cable to the expansion chassis Connect the ECH PCDSF H4A to the expansion adapter EAD CB SF installed on the PC as shown below ECH PCI SF H 2B F 2B H 4B F 4B EAD CB SF ECH PCI SF H4A Figure 2 4 Connecting the expansion bus adapter LINK LED The LINK LEDs show whether the switch fabric device is working normally Both of the TX and RX LEDs remain on when the device is working normally If they are blinking or off see Setup Troubleshooting CAUTION The PC may malfunction if link disconnection occurs with the LINK LED blinking or of
22. ts obtained by the user as a result of using this product Trademarks MS Microsoft Windows and Windows NT are trademarks of Microsoft Corporation Other brand and product names are trademarks of their respective holder CONTEC ii EAD CB SF CONTEC EAD CB SF Table of Contents Check Your Packages e iss A ERER A EA EER EETA TERE OERA i Copyright R E E rece E E E E E E E E sad daaee ds ii Trademarks Table of Contents 1 BEFORE USING THE PRODUCT 1 A bout the adaplete sca Gorsls cs eceal ed ceva sued onward coteaatareumennle E meet Ante E Oat ade 1 PE ATUIECS 0 200 8 chsh lates sccest asia ES EE EE S EEAS E 1 Expansion chassis QPO siscccsssiscessssccuscsddiscanssdcenseacedscostsdcenavadascosasdcavavsiaievondsdcqnavsislevavasiansaasia 1 Connection cable Opon erena aE R TA ER EE E A EAR ERE 1 Combinations of Expansion Adapters and Expansion Chassis s sssssssssssissirerersrerererererene 2 RestiictionS esetrae a K E E AEA E aden E A e Er OE REES 3 COEK n o1 NAON 29 0103 1 EE AA EAA AS A E E E 4 AES Le eile E EEE E A EEEO EEEE E E 4 Limited Three Y ears Warranty is os sisecoss sais sevsdvssaesstis desi orita ireu ea sdsceessasasevsceiidassetadsevseaiataresastcensesss 4 1e LOAA ORO 161 1 EaSI DA 1e aae E E E E E E anata 4 Liability saa O EA E EE E EA A E EE EV EA EEE A 4 Safety Precautions sinne E E EARE E R R A E E 5 Safety Information sassa a E E E E EE EE NE REEE AI E 5 Handling Precautions irese soea oseer
23. w default Latency CashLineSize 4010 Use default Device manager Cancel Help Figure 2 8 Example of driver setting utility dialog box CONTEC EAD CB SF 23 2 Setup Uninstalling the driver To uninstall the EAD CB driver use Add Remove Programs in the Control Panel E Add or Remove Programs OBR amp Currently installed programs Sort by Name Change or s CONTEC EAD CB Driver for Windows XP 2000 Remove Programs To change this program or remove it From your computer click Change Remove EEE Figure 2 9 Prompt to uninstall CONTEC 24 EAD CB SF 2 Setup Setup Troubleshooting Please confirm followings when EAD CB SF does not work Symptoms and Actions The chassis won t be turned on eno oP Make sure that the power cable has been connected correctly Make sure that the AC adapter has been connected correctly Make sure that the power supplies of the PC and expansion chassis are on Make sure that you have followed the procedure in Chapter 2 Even though the chassis is still not turned on check whether it is turned on with no board installed If the chassis is turned on with no board installed check the total current consumption by the installed boards The total current consumption must not exceed the power capacity of the expansion chassis No PCI board on the expansion chassis is detected f g CONTEC Make sure that the PC Card BUS PC
24. w Hardware Wizard cecseccseseeeesseseeeeseeecsecseeeesesaeseesesesseeeesetaseeeaeeaes 17 Setup Froubleshootin geese E ete A EA h ea ae lisse ae cea head cute E Symptoms and Actions 3 ABOUT HARDWARE 27 Hard ware SpeCifica tl Oni E a e E E E A RS 27 CONTEC EAD CB SF v 1 Before Using the Product 1 Before Using the Product This chapter provides information you should know before using the product About the adapter The EAD CB SF is an expansion adapter that connects the optional expansion chassis ECH PCI SF to a PC to extend a CardBus compliant PC Card slot in the PC thereby providing additional PCI bus slots The expansion adapter can connect the expansion chassis to the PC over a distance of up to 12m EAD CB SF operates under Windows XP Windows 2000 Features Using high speed serial transfer 2 5 Gbps capable of extending the PCI bus to up to 12m Using a noise immune STP category 5e cable easy to wire and install Capable of expand the PCI buses 5V 32 bit 33 MHz from a notebook computer Expansion chassis free of choice according to the number of PCI bus slots and the board size required Power supply controllable in response to the turning on off of the PC s power supply Expansion chassis Option PCI Bus Expansion Chassis PCI Bus Expansion Chassis Short x 2Slots ECH PCI SF H2B PCI Bus Expansion Chassis Long x 2Slots ECH PCI SF F2B PCI Bus Expansion Chassis Short x

EAD(CB)SF

Contents

Download Pdf Manuals

Related Search

Related Contents