R08TH_2008 RT08TH V.1.0 ANG.cdr
Contents
1. TITLE RANGE DEFAULT FUNCTION DeltaKSL 1 20 C 10 C Temperature difference between the solar collector and the buffer causing the operation of the KSL pump P2 with max rotation MinDelta 0 20 C 2 C Temperature difference between the solar collector and the buffer No more causing the switch off of the KSL pump P2 than DeltaKSL t ZalPC 0 5 30 5 2 min Operation time of the circulating pump t WylPC 0 5 30 5 15 min Break time of the circulating pump PARAMETER LEVEL 2 TITLE RANGE DEFAULT FUNCTION STRF1 od 0 00 23 45 6 00 Start time of the 1st time zone STRF1 do 0 00 23 45 8 00 End time of the Ist time zone STRF2 od 0 00 23 45 14 00 Start time of the 2nd time zone STRF2 do 0 00 23 45 17 30 End time of the 2nd time zone STRF3 od 0 00 23 45 20 00 Start time of the 3rd time zone STRF3 do 0 00 23 45 22 30 End time of the 3rd time zone PARAMETER LEVEL 3 TITLE RANGE DEFAULT FUNCTION T maxKSL 80 200 C 110 C KSL protection against overheating Maximum temperature of the 7 collector after exceeding it the KSL pump P2 turns on protecting the collector against overheating The setting of 200 C off text indicates turning off this function T minKSL 30 10 3 C KSL protection against freezing Minimum temperature of the C collector after exceeding it the KSL pump P2 turns on protecting the collector against freezing The se2. Test report No 39 DL 1 07 of 22 06 2007 41 DL 1 07 of 03 07 2007 Electronic Engineering Plant TATAREK has initiated management system and complies with the following standard 1SO9001 2000 CERTIFICATE No 133 2004 of 01 2004 Polish Foreign Trade Chamber The last two digits of the year in which the CE marking was affixed 07 Place of issue Manufacturer representative Wroclaw Mirostaw Z asena Kasja Date of issue Position 08 2007 Konstruktor KSL Solar collector BUF Buffer T1 temperature sensor of the solar collector T2 temperature sensor of the solar collector mounted in the lower part T3 temperature sensor of the solar collector mounted in the upper part P1 circulating pump of the warm applicable water P2 feeding pump of the buffer from the solar collector continuous control of the rotation G3 electric heater or another heat source 1 1 Operation of the circulating pump P1 During the heat comfort time the circulating pump P1 turns on for a time defined by the tZatPC parameter and turns off acc to the tWy PC parameter Normally every 15 minutes the pump turns on for a 2min time Outside of the heat comfort time zone the pump doesn t run 1 2 Operation of the KSL pump P2 The collector pump P2 turns on with maximum rotation if the collector temperature T1 is higher than the buffer temperature T2 by the value of 10 C DeltaKSL parameter see PARAMETERS If the temperature difference begins
3. l Swithing on the heater can be prevented by setting the TminBUF parameter at minimum of 20 C The text off shows up T Power of the heater connected directly to the regulator cannot exceed 500W For more powerful heaters you need to apply an auxiliary contactor T with turning on the heater G3 simultaneously the nonvoltage contacts of the relay STEROWANIE get switched over You can use them to connect another alternative heat source e g gas boiler 3 1 4 URLOP mode This is a special operation mode applied when for a longer timer the system is not normally used that is there s no heat receiving from the buffer In this mode the maximum temperature of BUF is set at 45 C leaving a reserve for accumulating the heat in case of protecting the collector against overheating The heat is dispersed in the collector when its temperature falls below the buffer temperature by the DeltaK SL value Cooling the system by night and on overcast days T In the URLOP mode the KSL protection against overheating should not be switched off T In the URLOP mode turning on the heater G3 is blocked 2 Handling the regulator On the control panel Fig 2 are the controls of the regulator The regulator state is shown on the text display 1 The displayed screens inform about device operation sensor temperature enable changing the parameters etc The change of the screen is made by pressing the WYBIERZ button 2 If this is a s
4. decreasing then the rotation of the pump accordingly get lower down to complete switch off when the difference reaches 2 C MinDelta parameter Ifthe buffer temperature BUF exceeds 60 C TmaxBUF parameter the CWU pump turns off l Despite limiting the temperature of the CWU container T max CWU parameter on the output of the warm water you need to apply a thermostatic antiburn valve which through mixing with cold water keeps the temperature range of 35 C 60 C set by the setting handle l Exceeding the maximum temperature of the solar collector T maxKSL parameter causes turning on the KSL pump P2 protecting the collector against overheating The KSL protection has a higher priority than limiting the temperature of the CWU l Exceeding the minimum temperature of the solar collector T minKSL parameter causes turning on the KSL pump P2 protecting the collector against freezing The KSL protection has a higher priority than limiting the temperature of the CWU 1 3 Operation of the heater G3 or another heat source When the heat comfort setting is active the electric heater or another heat source warms up the upper part of the container The heater turns off when the temperature measured in the upper part of the buffer container reaches the TminBUF value default setting 40 C and again turns on when the temperature falls by 4 C Outside of the heat comfort zone the heater doesn t work
5. for damage caused by atmospheric discharge 2 and overvoltage in the mains 3 Burnt fuses are not subject to warranty replacement Date of sale Seller s signature and stamp ARGO FILM Recycling Plant No 6 180 Krakowska st 52 015 Wroclaw Register No GIOS E 0002240WZ Worn out electronic the utilization collection place where will 0 515 122 142 be accepted for free and electric devices must be transfered to Ph 071 794 43 01 bs INIA X K C Zak ad elektroniczny TATAREK Jerzy Tatarek 50 559 Wroclaw 75 Swieradowska st ph 071 367 21 67 373 14 88 fax 373 14 58 tax index number 899 020 21 48 Bank account BZ WBK S A O WROCLAW 6910901522 0000 0000 5201 9335 www tatarek com pl E mail tatarek tatarek com pl Model change of the TmaxKSL parameter defining the protection temperature of the solar collector Parameter of the level 3 You press erepeatedly WYBIERZ till the PoziomUS 0 screen of setting the parameters shows up e USTAW gt 0 begins blinking ethreefold gt 3 blinks e USTAW gt 3 stops blinking the parameter of the level 3 is chosen e WY BIERZ gt TmaxKSL shows up e USTAW gt the actual value to be changed starts blinking e gt you set a new value e USTAW gt you confirm the new value erepeatedly WYBIERZ till the screen of setting the parameters shows up 3 Installing
6. over You can use them to connect another alternative heat source e g gas boiler s 2 1 Time zones The regulator is equipped with the clock which enables an automatic change of the operation mode at different times of the day The 24 hr is devided into 3 zones 1 2 3 and the time span when no zone is active that is STREFA 0 or BAZA The time zone is defined by the start time OD and the end time DO In the regulator the following zone default program is set STREFA 1 1 OD 6 00 DO 8 00 STREFA 2 2 OD 14 00 DO 17 30 STREFA 3 3 OD 20 00 DO22 30 T the zones 1 2 or 3 are the heat comfort zones When they re active the circulating pump can operate and the warming up of the buffer is possible 2 2 Screens The emergency screen is not visible till one of the following emergency situations takes place 1 Damage of the sensor T1 of the solar collector The text T1 KSL shows up 2 Damage of the sensor T2 ofthe buffer T2 BUF 3 Damage of the sensor T3 of the buffer T3 BUF 4 Exceeding the limit temperature of 90 C in the buffer TmaxBUF ALARM Tmax BUF The emergency situation is accompanied by a broken sound signal which can be cancelled with the USTAW button Operation screen of the collector On the display are shown the symbols of devices KSL solar collector BUF buffer Below them respectively the measured temperature If instead of the degree symbol the symbol is
7. system This mode should be activated if for a longer time there be no heat receiving from the buffer MAN KSL pump turns on with maximum efficiency no matter what the KSL and BUF temperature are e g for venting the system snowing off the collector The switch on lasts for the time determined by the CzasMan parameter see PARAMETER LEVEL 1 After the time the AUTO mode is restored It s a unstable screen that is after 10s from the last pressing of any button the screen switches to that of the whole system operation All the next screens are unstable Screen of the clock The screen shows the current time and number of active time zone The time correction is possible after pressing the USTAW button 5 In reaction to that the minutes field starts blinking The blinking value you can change by pressing the 2 or 4 button By pressing the WYBIERZ button 3 you step through to the hours field the value of which you can also change by the 2 or 4 button Pressing the USTAW button 5 confirms the changes the clock field stops blinking 0 Screen of setting the parameters Normally the level of setting is 0 which means the parameters are not available After switching to the level 1 2 or 3 the subsequent screens show the parameters The last screen displays after which the comeback to the previously described screens follows PARAMETER LEVEL 11
8. WNAS Zak ad elektroniczny TATAREK Jerzy Tatarek 50 559 Wroclaw 75 Swieradowska st ph 071 367 21 67 373 14 88 fax 373 14 58 Tax index number 899 020 21 48 Bank account BZ WBK S A WROCLAW 6910901522 0000 0000 5201 9335 www tatarek com pl E mail tatarek tatarek com pl 12 WANA Zak ad elektroniczny TATAREK Jerzy Tatarek RO8TH 2010 v 1 0 ANG USER MANUAL RT 08TH REGULATOR OF HEATING CIRCULATION WITH THE SOLAR COLLECTOR v 1 0 04 11 2009 program from 1v0 WYBIERZ CX The regulator controls the heating system in which a heat source is a solar collector The heat receiver is a buffer The pump of the solar collector runs with a continuous control of its rotation which enables a optimal use of the collector heat The regulator is equipped with a clock which at selected times of the day turns on the circulating pump of the applicable water and the alternative heat source as well electric heater gas boiler and the like 1 Basic parameters Power supply Power consumption without the load Max connection power Operation conditions Housing protection class Fuse Number of outputs to control the pump of the solar collector Number of additional outputs Number of temperature sensors of the solar collector Number of water temperature sensors Temp measurement precision Temp measurement resolution Number of the time zones 230V 50Hz 5W 750W 0 50 C humidit
9. creen that enables changing a parameter then you need to press the USTAW button 5 The parameter field starts blinking the value of which can be altered with the 2 or 4 button D Q Fig 2 Control panel Text display Increase button Parameter button Decrease button Confirmation button Oi ei With the USTAW button 5 you confirm the changes the parameter field stops blinking The changed parameter not confirmed for 10s is not stored by the regulator The field stops blinking and the previous value is restored WARRANTY 1 Warranty is valid 24 months from the date of sale 2 Producer does not take responsibility for any mechanical damages made by user 3 MAKING REPAIRS OR MODYFYING THE DEVICE BY USER IS FORBIDDEN AND CAUSES WARRANTY CANCELATION 4 Warranty card is valid only with date of sale seller s signature and stamp 5 Warranty and after warranty repairs should be done only by producer damaged regulators should be sent to producer in order to make all repairs needed 6 Warranty protection involves the EU 7 Warranty does not exclude not restrict and not suspend buyer s rights coming from the incompatibility of the article with the agreement Laws Journal No 141 Pos 1176 WARNING ANY MODIFICATION OF THE REGULATOR MADE BY USER CAN BE THE CAUSE OF SAFETY CONDITIONS DETERIORATION AND CAN EXPOSE THE USER TO ELECTRIC SHOCK OR DAMAGE DEVICES SUPPLIED WARNING 1 Producer does not take the responsibility
10. f the system Fig 1 Operation layout of the regulator 2 Admission date Realization date Signature Remarks WATASS PRODUCENT ZASILACZY SIECIOWYCH ISO 9001 2000 CE CONFORMITY DECLARATION Ref No 58 RT 01 2007 1 B We ZAKLAD ELEKTRONICZNY TATAREK Jerzy Tatarek 75 Swieradowska St 50 559 Wroclaw declare under our sole responsibility that the product Regulator of heating circulation with the solar collector model RT 08 RT 08T RT 08K RT 08P RT O8TH RT 08TL is in conformity with the basic requirements included in Directive EMC 2004 108 WE of 15 12 2004 the electromagnetic compatibility law of 13 04 07 and Directive LVD 2006 95 WE of 21 08 07 Laws Journal of 2007 No 155 pos 1098 regarding the requirements for electric devices To the conformity evaluation the following harmonized standards were used PN EN 60730 2 1 2002 Automatic electric regulators for house usage and the like Part 2 1 Specific requirements regarding electric regulators for electric house devices Automatic electric regulators for house usage and the like Part 1 General requirements PN EN 60730 1 2002 PN EN 55022 2000 Electromagnetic compatibility EMC IT devices Characteristics of radioelectric noises Acceptable levels and measurement methods Complementary information Laboratory IASE 51 618 Wroclaw 1 Wystawowa st
11. shown then that means exceeding the preset temperature and turning on the protection mode see the description of the parameters The blinking arrow indicates the actual heat flow in reaction to the pump operation ALARM T1 KSL If the URLOP mode is turned on with cooling the system the URLOP text blinks and the arrow indicating the heat flow can be directed opposite that is from the buffer to the collector if the pump runs in the cooling mode This is a stable screen In order to change it you need to press the WYBIERZ button Operation and circulation screen of the heater On the display are shown the devices symbols Grz heater BUF buffer and PC circulating pump Below the symbol of the buffer the temperature in the upper part of the container T3 is shown Ifthe sensor T3 is not mounted then in place of the temperature value the text shows up and turning on the heater will be blocked Th blinking arrow indicates the actual heat flow in reaction to the heater operation 5 Grz Ifthe circulating pump runs then at its symbol PC the symbol blinks This is a stable screen In order to change it you need to press the WY BIERZ button Screen of the regulator operation TrybKSL AUTO the regulator can operate in the mode AUTO KSL pump runs in the function of the temperatures difference between KSL and CWU URLOP KSL pump runs in the cooling mode of the
12. the regulator THE REGULATOR IS SUPPLIED BY 230V 50HZ ANY MOVES REGARDING INSTALLATION SHOULD BE MADE ATTHE DISCONNECTED MAINS THE REGULATOR HAS TO BE CONNECTED TO THE MAINS WITH THE ZERO PIN THROUGH A DIFFERENTIAL DEVICE ACC TO THE VALID LAWS THE REGULATOR SHOULD NOT BE EXPOSED TO WATER AFFECTING ITS ENVIRONS OUGHT TOBECLEAN THE PRODUCER DOESN T TAKE ANY RESPONSIBILITY FOR DAMAGES CAUSED BY WRONG USAGE OF THE REGULATOR Connection diagram of the elements of the regulator is presented on fig 3 aan Temperature sensors T1 KSL T2 BLF T3 BJF aa 2 O S 8 60e2200 02 N_FE Li FE FE PE LAN L2yN LaWN STEROWANIE CONTROL Pump P1 PC Pump P2 KSL 230V 50Hz 230V 50Hz Heater G3 MAINS 230V 50Hz ________ 230V 50Hz Fig 3 Electric wiring layout Tl temperature sensor of the solar collector KSL type KTY 84 T2 temperature sensor of the BUF buffer mounted in the lower part type KTY81 T3 temperature sensor of the BUF buffer mounted in the upper part type KTY81 Sensor T1 you need to connect so that the red cable is connected to the contact When there s no T3 sensor the heater is blocked Power of the heater connected directly to the regulator must not exceed 500W For more powerful heaters you need to apply an additional contactor With turning on the heater G3 simultaneously the nonvoltage contacts of the relay STEROWANIE get switched
13. tting of 30 C off text indicates turning off this function This function can be turned off in case of using a nonfreezing fluid in the solar T maxBUF 40 85 C 60 C BUF protection against overheating Maximum temperature of the buffer after exceeding it the pump turns off protecting the buffer against overheating KSL protection has a higher priority than BUF one T minBUF 20 60 C 40 C Temperature of the upper part of the buffer after reaching it the heater or another alternative heat source turns off The setting of 20 C off text shows up indicates turning off the warming up option ObrotMIN 10 100 30 Minimum rotation of the pump ensuring a stable operation The setting of 100 enforces ON OFF operation tminKSL 10 900s 10s Minimum operation break time of the collector pump It protects against too often turning on off the pump CzasMAN 1 30min Operation time of the KSL pump P2 in the MAN mode
14. y 10 90 no condensation IP41 6 3A 250V 1 1A 230V 50Hz triac continuous rotation control 2 250W 230V 50Hz 1 KTY84 30 200 C 2 KTY81 10 100 C 2 C 0 5 C 3 2 Operation principle The RT 08TH SOLAR regulator is a microprocessor regulator that controls the operation of the heating system consisted ofthe buffer BUF and the solar collector KSL see fig 1 The pump of the collector P2 turns on with maximum rotation if the temperature of the collector T1 is higher than the temperature of the buffer T2 by the value of the DeltaKSL parameter If the difference begins decreasing then the rotation of the pump accordingly get lower down to complete switch off when the difference reaches the MinKSL parameter value Thanks to the installed clock youcan set during the day the times of heat comfort In those times the circulating pump of the warm applicable water CWU P1 turns on cyclically in order to ensure a fast reaction of the CWU and the electric heater or another heat source gets started when the temperature measured in the upper part of the buffer is lower than the TminBUF parameter The regulator realizes additional functions of the control protection of the buffer against overheating protection of the solar collector KSL against overheating protection of the KSL against freezing signalling of any damages to the temperature sensors URLOP operation mode with the cooling o
Download Pdf Manuals
Related Search