U.motion U.motion Client Touch 10 U.motion
Contents
1. Apple Safari However it is not recommended to use the following browsers because they can t represent all the functions of U motion Client Touch correctly Microsoft Internet Explorer Opera The browser compatibility is continuously under development it is recommended to check out the list of the compatible browsers in the documentation of newly released product versions C3 Access On delivery U motion Client Touch has preconfigured the following users Username Password Description admin admin System Administrator manager manager User for the installation configuration of the system user user Basic user for client access On the first configuration of U motion Client Touch you must login with the admin user Do this by entering the appropriate data which in the connection also can be changed into the login screen once logged in you will see the following screen Version 1 0 0 RC 9 SAVE CLEAR CACHE LOGOUT gt Setup Users and permissions Schneider U motion Client Touch 10 15 Electric Technical Manual Note The users of U motion Client Touch can be edited but it is not possible to change their access WD rights or to create completely new users Since for the configuration and usage no further users on client side are required this minimalistic user management is enough for U motion Client Touch C4 Administration area interface The ADMINISTRATION i2. BACKEND Configuration area in which depending on the users permissions the settings of the U motion Client Touch can be modified VISUALISATION Visualisation area is transferred directly from the configured U motion KNX Server Plus Please note that in case of the U motion Client Touch only the configuration area is available directly on the device since the visualisation is received directly from the connected U motion KNX Server Plus Therefore the settings described on the last pages always refer to settings of the U motion Client Touch if instead you want to modify settings of the visualisation you will have to access the configuration area of the connected U motion KNX Server Plus 18 Schneider U motion Client Touch 10 15 MP Electric Technical Manual As long as no server has been configured in the configuration area of the U motion Client Touch no visualisation area can be loaded and therefore after each reboot the U motion Client Touch will just load its own configuration area Once a corresponding IP address has been configured the U motion Client Touch will show a special loading screen for app 20 seconds through which it will be possible to select the desired access if the loading screen is ignored the visualisation area of the entered server IP will be loaded if instead the shown CANCEL button is pressed the loading is aborted and the configuration area of the U motion Client Touch is shown again T
3. Network Update Backup Restore Date Time Display v Users and permissions v Users _ admin manager user If the properties window of an entry is opened through the EDIT action the entry will show an arrow icon instead of 3 points on the right side This icon will be displayed until the configuration window of the entry is closed and shall facilitate the navigation if multiple tabs are opened in the workspace Version 1 0 0 RC 9 SAVE CLEAR CACHE EXPERT LOGOUT pe Menu o cLosE 7 v Setup Language Object properties Network General information Update Username admin Backup Restore Date Time Password jj eseccseces Displa de Repeat password v Users and permissions v Users manager user C6 2 Menu structure The navigation menu permits to access all the settings of U motion Client Touch and has the following structure SETUP Contains generic settings and parameters of the U motion Client Touch USERS AND PERMISSIONS Allows the modification of the existing 3 users C7 Setup The menu SETUP contains the following entries LANGUAGE Permits to change the language of the configuration area NETWORK Permits to configure the network parameters of U motion Client Touch UPDATE Permits to update the devices through specific update packages s12 Schneider U motion Client Touch 10 15 Electric Technical Manual BACKUP RESTORE
4. MANAGEMENT the already uploaded images 17 Schneider U motion Client Touch 10 15 Electric Technical Manual SELECT BACKGROUND IMAGE ETF A Through the UPLOAD button further pictures can be uploaded to U motion Client Touch Through the X button the corresponding picture can be removed from U motion Client Touch C7 6 3 Touchscreen Through the calibration the touchscreen can be optimized for the customer CALIBRATION A single click on the button CALIBRATE NOW starts the calibration procedure on the display of U motion Client Touch During this procedure 4 crosses appear on the display of U motion Client Touch which must be pressed by the customer one after another Once all crosses have been pressed the calibration process is done The calibration process can be started only from the administration menu which is accessible D either by a remote PC desktop PC notebook or locally directly on the device The first option brings the advantage that the calibration can be started even when the touchscreen can t be used anymore e g because of a wrong calibration TAKE CARE the calibration itself always must be done directly on the device through its touchscreen even when launched locally C8 Administration and visualisation area As already mentioned the interface of U motion Client Touch is split into two areas ADMINISTRATION or
5. U motion Password Login 2012 Schneider Electric Industries SAS All Rights Reserved To do so simply highlight the box named USERNAME and enter the username with which you want to login Select the field PASSWORD and enter the password corresponding to the entered user name Finally click on LOGIN in order to access the visualisation A software keyboard will appear on the screen through which username and password can be entered on the touch screen of U motion Client Touch with the finger Please note that this login window doesn t accept the local user of the U motion Client Touch but requires a valid user of the connected U motion KNX Server Plus If the configuration of the connected server already contains a user which was configured using the trusted IP setting pointing to the IP address of the U motion Client Touch the login window will not be shown and U motion Client Touch will directly show the home page of the visualisation Further information about the configuration and usage of the contents of the visualisation can be found in both the installation and user manual of U motion KNX Server Plus 20 Schneider U motion Client Touch 10 15 f Electric D TECHNICAL DATA D1 Mechanical data Outside dimensions U motion Touch Design element U ee width d height e Cut out dimensions U motion Touch Cavity wall set Je p Technical Manual Dimensions U motion Touch Cav
6. U motion Client Touch in order to make it work correctly with a present U motion KNX Server Plus system C2 Network connection For the usage configuration of U motion Client Touch a working network connection is required In order to make the first access to U motion Client Touch or if a compatible network is not available follow these steps Connect U motion Client Touch through a crossed network cable with your PC Open the network configuration of your PC Change the settings of the TCP IP Protocol Version 4 of the network interface on which you connected the network cable and enter the following values Schneider U motion Client Touch 10 15 Electric Technical Manual e IP address 192 168 0 100 Subnet mask 255 255 255 0 e Gateway 192 168 0 130 Save the new settings depending on the installed OS a restart can be necessary The following screenshots show how to change the network settings on Windows XP Local Area Connection Properties F p 7 Internet Protocol TCPAP Properties General Advanced General l Connect using fou can get IF settings assigned automatically if your network supports this capability therwise You need to ask pour network administrator for BS Realtek Flle GBE Family Controller the appropriate P settings This connection uses the following items O Obtain an IP address automatically tl Link NetBIOS A Use the following IP address 7 AM Link Per SPee MetBI
7. co oa configuration WEINE cLoseE v Setup Language Energy management and screensaver Network Screensaver timeout 0 05 00 Update Backup Restore Power saving management Disable power saving Date Time Timeout for display power off 0 10 40 Users and permissions Images Screensaver picture management Touchscreen Calibration C7 6 1 Power management and screensaver The following options are available SCREENSAVER If for the defined timeout the touchscreen of U motion Client Touch is not operated TIMEOUT the screensaver function will start POWER SAVING This enables disables the power saving mode If the power saving mode is turned MANAGEMENT on the display of U motion Client Touch will be powered off if for a defined timeout the touchscreen of the device is not used TIMEOUT FOR If the power saving mode is enabled this field permits to set the timeout after which DISPLAY POWER OFF the display should be turned off if not operated The settings will be saved correctly only when the SAVE button is pressed The graphical surface of U motion Client Touch will be restarted as soon as the SAVE button is pressed this procedure can take up to 1 minute C7 6 2 Images Through this option custom images can be uploaded to U motion Client Touch for being used from the integrated screensaver SCREENSAVER PICTURE A single click on the example picture opens a popup window which contains
8. may cause damage to material E Note D Hint and additional notes Schneider U motion Client Touch 10 15 Electric Technical Manual SAFETY INSTRUCTIONS The present operating instructions contain those safety instructions that are required to safely operate the machine All persons working with the machine must heed the present operating instructions especially the safety instructions In addition all local stipulations governing the prevention of accidents must be heeded Only trained and authorized personnel may install and operate the machine Proper application The machine has been designed for application in a building environment The machine meets the requirements of the EMC guidelines and of the harmonized European standards Modifications to the machine hardware may affect the system s EMC compatibility Without special protection measures the machine must not be used in EX areas and in plants that require special monitoring Danger of explosion Do not expose the buffer batteries to heat Serious injury may be the result The operating voltage of the machine must be within the specified range The product label provides the required information Schneider U motion Client Touch 10 15 Electric Technical Manual CONTENTS General Information 1 Conventions 1 Safety instructions 2 Contents 3 A Product description A Al Front view U motion Client Touch A A2 Interfaces U motion Client Touch 5 A3 Scope of del
9. EAR CACHE Allows deleting the HTML CACHE of the client This is especially necessary if changes made on the server are not displayed correctly in the visualisation LOGOUT Ends the current session VISUALISATION Allows switching to the visualisation area of the configured U motion KNX Server Plus is only shown when working locally on the device C6 Navigation menu C6 1 Usage The navigation menu is a typical tree view menu After accessing the configuration area all the main entries are shown the sub menus are accessed by extending the corresponding main menu The navigation in this menu is done entirely with a mouse Clicking on an entry in the navigation menu turns the clicked entry into grey if the entry has additional submenus the entry will be extended and the sub menus are displayed Another click on the selected entry will close the section and hide the submenus again Version 1 0 0 RC 9 SAVE CLEAR CACHE LOGOUT v Setup Language Network Update Backup Restore Date Time Display v Users and permissions admin manager user If the selected entry supports the EDIT action 3 points will be displayed on the right side of the entry Clicking on these points will open the properties window of the selected entry 11 Schneider U motion Client Touch 10 15 Electric Technical Manual Version 1 0 0 RC 9 SAVE CLEAR CACHE LOGOUT v Setup Language
10. OS Compatible Transport Prot ee 468 0 100 pg nternet Protocol TCPYIP Subnet mask 255 255 0 lill Default gateway 168 0 110 Description Transmission Control Protocol Internet Protocol The default Use the following DNS server addresses Wide area network protocol that provides communication across diverse interconnected networks Preferred DNS server Alternate DNS server C Show icon in notification area when connected Notify me when this connection has limited or no conmectyvity Once the network settings have been changed open a browser on your PC Google Chrome preferred and enter the following URL into the address bar of the browser http 192 168 0 130 This link will open directly the configuration menu of U motion Client Touch if the network connection is working properly you will see the following screen ACCESS Username Password Remain connected 4 Schneider U motion Client Touch 10 15 Electric Technical Manual Alternatively you can also access the configuration area locally on the U motion Client Touch the same login window will be shown As long as no U motion KNX Server Plus has been configured in the configuration area U motion Client Touch will always load its configuration area Note If you access the device remotely the maximum comfort for using programming U motion a Client Touch can be achieved with the following browsers Google Chrome
11. Permits to reset the database to factory settings DATE TIME Permits to configure date time of the device and all date time related settings DISPLAY Allows the configuration of the screensaver and display power off settings of the device Additionally the calibration of the touchscreen can be started from within this settings page The following chapters will describe the single options in detail C7 1 Language This page allows the configuration of the language that should be used for the configuration area of U motion Client Touch Select the desired language and click on SAVE Once the storage procedure is completed the page will be refreshed and displayed in the selected language TAKE CARE the language shown within the visualisation is not defined by the settings of the U motion Client Touch but by the settings of the connected U motion KNX Server Plus Version 1 0 0 RC 9 SAVE CLEAR CACHE EXPERT LOGOUT Language pM Language BES close v Setup Language gt Current language EIS admin English x Update Backup Restore Date Time sive cos Display gt Users and permissions C7 2 Network This page allows the configuration of the network parameters of U motion Client Touch Version 1 0 0 RC 9 SAVE CLEAR CACHE EXPERT LOGOUT pm Menu Network configuration i CLOSE v Setup Language Client Network U motion KNX Server IP Address 192 168 0 110 Update Backu
12. U motion U motion Client Touch 10 U motion Client Touch 15 Technical Manual Art no MTN6260 0310 MTN6260 0315 04 2014 Version 1 0 1 Schneider www schneider electric com L Electric Schneider U motion Client Touch 10 15 f Electric Technical Manual GENERAL INFORMATION Schneider Electric SAS If you have technical questions please contact the Customer Care Centre in your country www schneider electric com Operating instructions manuals and software are protected by copyright All rights are reserved Copying multiplication translation and conversion either partially or as a whole is not permitted You are allowed to make a single copy for backup purposes Note please read the manual before beginning and keep the manual for later use Audience the manual has been conceived and written for users who are experienced in the use of PCs and automation technology CONVENTIONS KEY Keys that are to be pressed by the user are given in square brackets e g CTRL or DEL Courier On screen messages are given in the Courier font e g C gt Courier bold input to be made by the user are given in Courier bold e g C gt DIR double quotes Names of buttons to be pressed menus or other onscreen elements and product names are given within double quotes e g Configuration Symbolic In this manual the following symbolic are used to indicate particular text blocks Caution A dangerous situation may arise that
13. ck at least 1 5 cm or in a cavity wall construction The cut out has to respect the sizes specified in the technical data and has to be at least 8 cm deep In the wall cut out the flush mounting box can become build in while the cavity wall set can be screwed on in a piece of furniture or in a cavity wall It is important that the fore edge of the wall mount kit is flat and horizontally to the surface of the wall or the piece of furniture The flush mounting box offers cable access at all four sides Note detailed information about the mounting can be found in the documentation of the i corresponding mounting set attached to the mounting set and present on the U motion USB stick Installing U motion Client Touch After the correct cabling the PC is put into the wall mount box and is fixed with the four screws delivered with the mounting set Now you can install your U motion Touch Design element with slight even pressure Caution AN Unauthorized changes or modifications to the PC configuration may result in permanent damage to the system or its functionality Only authorized trained personnel are allowed to make any modifications Schneider U motion Client Touch 10 15 Electric Technical Manual Caution A Permanent operation of the hard disk can cause damages To prevent this the power management set up must be enabled When running 24 hours a day the hard disk should be parked at least once a week This function is provided
14. his additional loading screen simply guarantees that an access to the local settings remains possible also with a configured server IP address C9 First access after configuration If a valid IP address has been configured U motion Client Touch will automatically load the visualisation area of the connected U motion KNX Server Plus As already mentioned in the last chapter this can be stopped by cancelling the first loading screens accessing in this way the configuration area of U motion Client Touch Otherwise after each reboot different information from the server is loaded into the local cache and stored there HTML client cache DB client cache This information is used later to navigate in the visualisation and to command the different objects by preloading this information all future accesses are accelerated and the operating is nearly at real time level Even if the browser is closed or restarted the cache will be kept and no reloading is needed The different cache technologies can also be disabled if wanted detailed information on how this is realized can be found in the installation manual of the U motion KNX Server Plus The following screen is shown during the loading period Loading resources 19 Schneider U motion Client Touch 10 15 Electric Technical Manual Normally after the initial loading process a login window is shown through which the U motion Client Touch must register on the connected server
15. hlt Users and permissions The update process runs completely automatically please wait for feedback from the page without performing other tasks or exiting the browser risk of data loss malfunction Depending on the configuration and software version the update may take several minutes Once the update process is completed a brief summary as well as the new software version is displayed To complete the update please click on the Restart now button which will restart the operating system of U motion Client Touch C7 4 Backup Restore This page allows to reset U motion Client Touch to factory settings the IP address will NOT be affected by the reset Version 1 0 0 RC 9 SAVE CLEAR CACHE EXPERT LOGOUT Backup Restore Pee Backup Restore Egua close v Setup Language Database Network ons Reset Restore factory settings Update os EEE oo Date Time Display Users and permissions Just select the available action click on EXECUTE and wait for the action to be processed Neither cancel the started action nor close the browser window during this process C7 5 Date Time This page allows setting several parameters related to date and time of the U motion Client Touch 5 Schneider U motion Client Touch 10 15 SAVE CLEAR CACHE EXPERT Technical Manual LOGOUT Date Time v Setup Language Network Update Backup Restore Date Tir Display Users and permi
16. ing the single parameters please click on SAVE If the IP address was changed the new IP address must be entered in the address bar of the browser for reconnecting with the U motion Client Touch only if you are accessing the settings remotely Please ensure that all entered data is correct before you save them If incorrect settings are saved U motion Client Touch will probably be no longer accessible through the network C7 3 Update This menu permits to update the software version of the U motion Client Touch please use only official update packages published by the manufacturer in order to avoid malfunctions To update U motion Client Touch please proceed as follows Save the update package downloaded from homepage or received via mail on your PC without unpacking it Open the UPDATE menu in the ADMINISTRATION of the U motion Client Touch Choose the update package through the button Choose file or similar depends on the browser Check if the update package includes a newer version of the software version is shown on top Click on the button UPDATE 14 Schneider U motion Client Touch 10 15 Electric Technical Manual Version 1 0 0 RC 9 SAVE CLEAR CACHE EXPERT LOGOUT Update p CI O O Update yi cLose v Setup Language Current configuration Network Software version 1 0 0 RC 9 Backup Restore a Upload package Date Time Display Update package Datei ausw hlen Keine ausgew
17. ity wall set BE ET E For the cutout see the mounting guide Cut out U motion Touch 10 Cavity wall set flush mounting D ET ET I 7 Fixing elements T U motion Client Touch has to be fixed to the wall mount box using the 4 screws delivered with the mounting set e Mechanical characteristics U motion Touch 10 15 Design element Alloy anodized PC Unit 10 Plastic PC Unit 15 Alloy anodized Schneider U motion Client Touch 10 15 Electric Technical Manual D2 Maintenance and upkeep The U motion Client Touch is normally a completely fanless system a fact that reduces strongly the necessary maintenance expense Note 5 Additional information about the components which are used in U motion Client Touch you will find in the original documentation of the manufacturer II
18. ivery 5 B Commissioning 6 Bl Grounding chapter valid only for U motion Client Touch 15 6 B2 Commissioning 6 B3 Installing the U motion Client Touch 6 C The Operating System 7 C1 Introduction 7 C2 Network connection 7 C3 Access 9 C4 Administration area interface 10 C5 Toolbar 11 C6 Navigation menu 11 C6 1 Usage 11 C6 2 Menu structure 12 C Setup 12 C7 1 Language 13 C7 2 Network 13 C7 3 Update 14 C7 4 Backup Restore 15 C7 5 Date Time 15 C7 6 Display 16 C8 Administration and visualisation area 18 C9 First access after configuration 19 D Technical data 21 D1 Mechanical data 21 D2 Maintenance and upkeep 22 Sc r eid er U motion Client Touch 10 15 dr Ele r Technical Manual On A PRODUCT DESCRIPTION Al Front view U motion Client Touch e U motion Client Touch Image with U motion Touch Design element side view mounted Image U motion Client Touch 15 Schneider U motion Client Touch 10 15 Electric Technical Manual A2 Interfaces U motion Client Touch The U motion Client Touch has various connection possibilities on his back side All necessary interfaces can be found there Detailed information about all interfaces of the U motion Client Touch are described in the technical manual of the motherboard manufacturer An original copy of the manual can be found in the packaging A3 Scope of delivery Hardware U motion Client Touch 10 or 15 U motion Touch 10 or 15 Design e
19. lements RJ45 Connector RJ45 Patch cable Software Pre Installed fully functional operating system Documentation Safety notes General notes Quick Start Guide U motion USB Stick documentation and software Schneider U motion Client Touch 10 15 Electric Technical Manual B COMMISSIONING B1 Grounding chapter valid only for U motion Client Touch 15 The following must be heeded to ensure that all electrical interference is safely absorbed Connect the unit and the wall mount kit with a central grounding point using the shortest possible distance Make sure that the connection between the unit and the grounding point has the lowest possible impedance All data cables connected to the unit must be shielded The shields must be grounded at both ends A low impedance connection must be established between the linked units High compensation currents over the cable shields caused by potential differences must be excluded Use a green yellow cable with a minimum cross section of 2 5mm for ground connection B2 Commisstoning A three pin cold appliance connector supplies the U motion Client Touch The power supply must be 100 240 VAC More technical details of the power supply can be found on the type label of the power supply B3 Installing the U motion Client Touch Mounting U motion Touch Flush mounting box Cavity wall set The different mounting sets may be installed in a cut out in the wall in a wooden structure thi
20. p Restore LAN Date Time Display IP address 192 168 0 120 Users and permissions Subnet mask 255 255 248 0 Gateway 192 168 0 1 DNS Primary DNS 8 8 8 8 Secondary DNS 13 Schneider U motion Client Touch 10 15 Electric Technical Manual The available parameters are U MOTION KNX SERVER IP IP address of the U motion KNX Server Plus to which the U motion Client ADDRESS Touch should be connected As long as this field is not compiled the U motion Client Touch will only load its own configuration menu Only after the configuration of this address a connection to the corresponding server and therefore an access to the visualisation is possible IP ADDRESS IP address of the U motion Client Touch this address must be present in the network only once and must be compatible with the IP addresses of the other devices inside the same network like U motion KNX Server Plus if unsure please contact your network administrator SUBNET MASK If no special network configuration is used don t change the standard value 255 255 255 0 GATEWAY Enter the IP address of your router if present or the referenced server of the network if unsure please contact your network administrator PRIMARY DNS DNS addresses over which U motion Client Touch can access the internet if SECONDARY DNS available If no connection is possible with the default addresses please contact your network administrator After modify
21. s divided into the following sections Main menu of the software shown as a tree view Through this menu all sections of the software are accessible and objects can be created modified deleted TOOLBAR The toolbar in the upper side of the ADMINISTRATION is always shown and allows switching quickly to the mostly used functions through the related buttons WORKSPACE Main area for showing the chosen configuration options the single menus and configuration windows of the objects are shown in here It is possible to open more menus windows in the main area at the same time the different menus windows will be accessible through different tabs in this case The following screenshot shows the single sections of the ADMINISTRATION area Toolbar Version 1 0 0 RC 9 SAVE CLEAR CACHE LOGOUT gt Setup Users and permissions Menu Workspace 10 Schneider U motion Client Touch 10 15 Electric Technical Manual C5 Toolbar Following functions are always present in the toolbar SAVE Allows saving all changes into the flash memory of U motion Client Touch what will preserve the data even if the device is powered off The button turns red whenever changes are made but not saved yet In addition every 5 minutes an automatic saving of all changes takes place so pressing the SAVE button is only necessary if the system should be shut down restarted immediately after making the changes CL
22. ssions ND ime configuration MGM close Configuration of date and time Set time 15 28 Set date 03 01 2014 Timezone configuration Timezone area Europe Timezone city Rome z Plan online update of date time Ntpdate server time ien it Each Minutes 45 Scheduled services reboot automatically reboots the communication service Weekday Monday Tuesday Wednesday Thursday Friday Saturday Sunday At C7 5 1 Date Time configuration Permits to manually adjust the system time of the U motion Client Touch C7 5 2 Timzone settings Allows configuring the time zone in which U motion Client Touch is located C7 5 3 Online update Allows defining a time server and a time interval to update automatically the system time if no special settings are required it is recommended to use the default settings C7 5 4 Scheduled services reboot Provides an automatic restart of the services running on U motion Client Touch in the background week day and time for the automatic restart of the services can be configured here Normally the automatic restart of the services is not required therefore it is recommended to not change the factory settings C7 6 Display In this section all the settings for the display of U motion Client Touch can be configured and also the calibration of the touchscreen can be started 16 Schneider U motion Client Touch 10 15 Electric Technical Manual Version 1 0 0 RC 9 SAVE CLEAR CACHE EXPERT LOGOUT
23. when the power management setup of the BIOS is enabled Caution If you need to remove the U motion Touch Design element push it upward to unlock it and extract it from the mounting horizontally One sided traction or slanted installing can damage the element the ambient temperature does not exceed 30 C If this value is exceeded additional cooling has to be provided Separator For equipment with permanent connection an easily accessible separator shall be provided outside the equipment Caution A In order to be able to dissipate the warmth produced by the equipment it must be guaranteed that The equipment must be installed vertically i e the front plate must be in an angle of 90 to the base plate Installation has to be conform to HD 60364 4 41 or other national prescriptions C THE OPERATING SYSTEM C1 Introduction U motion Client Touch is a client touch panel for the supervision and visualisation of home amp building automation systems which have been realized on the basis of the worldwide KNX standard and U motion KNX Server Plus U motion Client Touch connects itself via network with a U motion KNX Server Plus and represents its graphical contents The configuration and control of the U motion Client Touch can be done locally on the device or remotely through its web interface which can be displayed within a common browser from each supported device operating system This chapter describes the configuration of
Download Pdf Manuals
Related Search