steady grip manual_V3
Contents
1. South Australia 5160 61 0 8 8186 3301 aussales yuneec com This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Onr CE X YUNECELC ELECTRIC AVIATION2. indicator showing time length of the recording on the APP Screen IMPORTANT NOTE You can choose to record video at 48 50 PAL or 60 NTSC frames per second by tapping the corresponding button near the upper left hand corner on main screen of the APP Keep in mind that the delay in the live video stream will be lowest at 48 and 50 as compared to 60 frames per second The pitch control wheel similar to a scroll wheel on a traditional computer mouse located on the top of the SteadyGrip allows you to set the pitch tilt position of the CGO2 GB from approximately straight ahead when the pitch control wheel is rolled backward toward the user to its maximum position to approximately straight down when the pitch control wheel is rolled out away from you until its maximum position And you can easily set a position in between by adjusting the pitch control wheel accordingly According to Figure 9a on page 9 QUICK TIP There s an adjustable counterbalance located on the rear of the CGO2 GB This counterbalance has been adjusted at the factory to provide the best balance and performance overall so typically it should NOT need to be adjusted However if you find that the CGO2 GB is making any buzzing sounds while powered on carefully twist the counterbalance in or out until the sound stops in order to achieve the best balance performance and photo video quality Yuneec products and accessories are guaranteed against manufacturing defe
3. to operate the equipment This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 5 8GHz frequency range Antenna Separation Distance Maintain a separation distance of at least 50mm 2 in between your body not including your fingers hands and wrists and the antennas to meet the RF exposure safety requirements determined by FCC_regulations Holding the SteadyGrip by the SATA Mente veyed ers tt markt YA USER MANUAL OVERVIEW CGO SteadyGrip Action Ground Handle for CGO Series Camera 1 CGO2 GB 2 Main Status LED 3 Pitch Control Roller Wheel 4 Rubberized Ergonomic Grip 5 On Off Switch 6 6AA Battery Compartment BATTERY WARNINGS AND USAGE GUIDELINES WARNING Alkaline Batteries May explode or leak and cause burn injury if recharged disposed of in fire mixed with a different battery type inserted backwards or disassembled Replace all batteries at the same time Do not carry batteries loose in your pocket or purse Do not remove the battery label WARNING All instructions and precautions must be read and followed exactly and you must follow instructions of the battery manufacturer WARNING procedures which if not properly followed create the probability of property damage collateral damage and serious injury or create a high probability of superficial injury Failure to exe
4. C C3 O steapyerip INTRODUCTION The CGO SteadyGrip is a ground handle designed to extend the CGO GB 3 axis gyro stabilized camera from the sky to the ground allowing you to capture amazing action shots easier than ever before The camera pitch controller allows precise camera angle control on the go using your mobile device as a display The Steady Grip s ergonomic design is capable of holding up to a 6 4 inch mobile device The SteadyGrip paired with Yuneec s CGO2 GB Full HD 3 Axis Stabilized Gimbal Camera System allows you to capture fluid footage right out the box Please take the time to read through this entire instruction manual for more information on safety battery charging camera controls and more before filming your first hit video Please also visit www Yuneec com for additional information including product updates bulletins videos and more CGO 2GB available separately is an innovative combination of 3 axis brushless gimbal camera and digital video downlink The Self Stabilizing gimbal makes it possible to capture amazing photographs and video footage for an array of uses And the built in digital video link delivers streaming video to 5 8GHz WiFi compatible iOS and Android equipped devices including smart phones and tablets as well as YUNEEC Personal Ground Stations WINDOWS SYSTEM REQUIREMENTS Windows XP Service Pack 2 or later or Vista 3 2GHz Pentium 4 or faster Minimum 4GB of system RAM MAC SYST
5. EM REQUIREMENTS Mac OS X 10 4 11 or later 2 0GHz Intel Core Duo or faster Minimum 4GB of system RAM CGO2 APP COMPATIBLE DEVICES Android Mobile Devices with 5 8GHz Support Apple iOS phone4s iphone 5 5c 5s 6 6 ipad mini mini 3 4 SPECIFICATIONS CGO STEADYGRIP Height 223mm 8 78 in Depth front to back 182mm 7 17 in Width 70mm 2 76 in Weight without gimbal batteries 200g 7 05 oz Required Batteries 2850mAh Energizer 6x 1 5V AA Batteries Sold Separately Runtime 48 64 minutes depending on usage CGO2 GB Height 115mm 4 5 in Width 74mm 2 9 in Depth 135mm 1 4 in Weight 185g 6 5 oz Video Resolution Full HD 1080p 60 50 or 48 fps Photo Resolution 12 Megapixels Transmission Distance Range Up to 600m 1970 ft depending on receiving device and environment Transmission Band 5 8GHz Storage memory microSD Class 10 up to 128GB NOTICES AND WARNINGS IMPORTANT NOTE All safety precautions and warnings instructions warranties and other collateral information is subject to change at the sole discretion of Yuneec For the most up to date information please visit the corresponding product page at www Yuneec com or contact the nearest Yuneec office or authorized distributor The following special language terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly f
6. Store The SteadyGrip features a camera pitch controller that allows precise camera angle control on the go Simply roll the pitch control wheel forward to move the camera pitch angle downward and roll the pitch control wheel backward to move the camera pitch angle upward Please review these instructions along with the illustrations to familiarize yourself on how to control the CGO2 GB with your SteadyGrip CGO2 APP seamlessly integrates camera controls and user settings of the CGO2 GB so you can easily take still photos and start stop video recording using the corresponding buttons touch screen buttons found on the app 1 To take a still photo press the White Still Photo Capture button to capture You ll hear an audible shutter sound from the APP and the LED indicator on the front of the CGO2 GB will change from glowing solid green to glowing solid blue It will take approximately 5 seconds to capture the photo and before you can take another still photo Gay Ca fohisstnpvenikK t 2 4wwartineec com IMPORTANT NOTE You cannot take still photos while recording video You MUST stop recording video in order to take still photos 2 To start stop recording video simply press the red button located on the APP You ll hear an audible indication from the APP each time the recording starts stops And while video is recording the LED indicator on the front of the CGO2 GB will flash blue and green and there will be an
7. TOY GENERAL SAFETY PRECAUTIONS AND WARNINGS WARNING Failure to use this product in the intended manner as described in instruction manual can result in damage to the product property and or cause serious injury This product is not a toy If misused it can cause serious bodily harm and damage to property WARNING As the user of this product you are solely and wholly responsible for operating it in a manner that does not endanger yourself and others or result in damage to the product or the property of others Always allow CGO2 GB and SteadyGrip to initialize properly by setting the SteadyGrip on a flat and stable surface prior to switching it on and allowing the SteadyGrip and CGO2 GB to initialize properly which sometimes takes about 4 8 seconds Always operate your SteadyGrip in a respectful and safe manner Do not attempt to operate your equipment in areas with potential magnetic and or radio interference including areas nearby broadcast towers power transmission stations high voltage power lines etc FCC INFORMATION This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority
8. cts for six 6 months from the original date of purchase Yuneec s sole obligation in the event of such defects during this period is to repair or replace the defective part or product with a comparable part or product at Yuneec s sole discretion Except for such repair or replacement the sale processing or other handling of this product is without warranty condition or other liability Damage including crash damage resulting from use accident or normal wear and tear is not covered by this or any warranty Yuneec assumes no liability for any accident injury death loss or other claim related to or resulting from the use of this product In no event shall Yuneec be liable for incidental or consequential damages relating to or resulting from the use of this product or any of its parts Please review the instructions carefully when using the products Returns or replacements of parts and or products may be subject to shipping handling replacement and or restocking fees IMPORTANT NOTE Drop or water damage is NOT covered under warranty http yuneec com support YUNEEC USA 5555 Ontario Mills Parkway Ontario CA91764 USA 1 855 2848888 sales yuneec com YUNEEC HK 2 F Man Shung Industrial Building 7 Lai Yip Street Kwun Tong Kowloon Hong Kong 852 3616 6071 asiasales yuneec com YUNEEC EU Nikolaus Otto Strasse 4 24568 Kaltenkirchen Germany 49 4191 932620 eusales yuneec com YUNEEC AU 53 Ellemsea Circuit Lonsdale
9. de in mount on the SteadyGrip e WANVW wasn diIdSAGVALS COE 3 STEP 2 Carefully connect the CGO2 GB s power control connector to the power control port of the CGO SteadyGrip and then insert a microSD card into the corresponding slot on the bottom of the CGO2 GB You can use the included 8GB card from your RTF package or any Class 10 microSD card up to 128GB STEP 3 Powering on and initialization Place your CGO SteadyGrip on a flat and stable surface then switch on the SteadyGrip and it will initialize after 4 8 seconds of no movement or vibration SteadyGrip Main LED Status Upon Powering On Green LED Blinking for 8 seconds Starting up Initialization and Then Solid Green for E T READY TO USE Low Voltage Warning Green LED Blinking Slowly Voltage Dropping Green Blinking LED Speeds Up As The Voltage Drops CGO2 GB Error Red LED Blinking The SteadyGrip s ergonomic design is capable of holding up to a 6 4 inch mobile device Step 1 Press the Curved Lip at the top front of the SteadyGrip as illustrated and fit your Mobile Device with the screen facing toward the Main LED and Pitch Control Wheel Step 2 Download the CGO2 APP on the Apple APPSTORE or Android APPS Marketplace Step 3 Connect your Mobile Device to the CGO2 GB s WiFi by selecting CGO2GB s SSID and by entering the WiFi Key Password 1234567890 ANDROID APP ON Available on the my Google pay l g App
10. ollowed create a possibility of property damage and or little to no possibility of injury CAUTION Procedures which if not properly followed create the probability of property damage and or a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and or serious injury or create a high probability of superficial injury WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product property and or cause serious injury WARNING This is a sophisticated consumer product It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this product in a safe and responsible manner could result in damage to the product property and or cause serious injury This product is not intended for use by children without direct adult supervision Do not use with incompatible components or alter this product in any way outside of the instructions provided by Yuneec The instruction manual contain instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings prior to assembly setup and or use in order to operate the product correctly and avoid damage or serious injury AGE RECOMMENDATION NOT FOR CHILDREN UNDER 14 YEARS THIS IS NOT A
11. rcise care while using this product and comply with the following conditions and guidance could result in product malfunction excessive heat fire property damage and ultimately injury Lithium lon batteries are not toys For the purpose of the document Li lon Li Po Li Fe NiCd or NiMH batteries will be described as Batteries Handling and Storage e Never alter puncture or impact Batteries or related components e Do not directly connect the terminals with metal objects This will short circuit Batteries resulting in heat and electrical discharge e Never store loose Batteries together the Batteries terminals may contact one another causing a short circuit e Never expose Batteries to extreme temperatures or direct sunlight e Always disconnect Batteries when not in use Before the First Charge e Ensure batteries are not damaged as this may cause a short circuit of fire Charging e Always refer to your charger s manual to ensure safe operation e Always charge Batteries in an open area away from flammable materials liquids and surfaces e Never charge Batteries that are hot to the touch above 120 F If at any time Batteries become damaged hot or begin to balloon or swell discontinue charging or discharging immediately Quickly and safely disconnect the charger Then place the Batteries and or charger in a safe open area away from flammable materials in an approved Li Po bag to observe After one hour remo
12. ttery Cover Door from the bottom of the SteadyGrip Hold the bottom of the SteadyGrip toward yourself with the front part facing downward Slide the battery cover door upward with slight force and inspect the AA battery compartment gt STEP 2 Install 6x AA Batteries For long life and extended run time we recommend Energizer 1 5V AA Batteries which are known to have 2 850mAh of stored energy The SteadyGrip will run for approximately 48 64 minutes depending on the gravity of usage STEP 3 Re installing the Battery Cover Door on the bottom of the SteadyGrip Once you ve installed 6 fresh AA batteries Hold the bottom of the SteadyGrip toward yourself with the front part facing downward Slide the battery cover door downward with slight force and ensure you hear and feel a noticeable click indicating the battery cover door has been closed securely ATTACHING THE CGO2 GB TO THE STEADYGRIP WARNING Before switching on the SteadyGrip it is highly recommended to first securely attach the CGO2 GB to your SteadyGrip QUICK TIP It s a good idea to ensure you have your microSD card with lots of space for photos and videos handy STEP 1 Carefully slide the top part of the CGO2 GB that also attaches below the nose of the Q500 Typhoon onto the mount below the front part of the SteadyGrip A corresponding click will be noticed once the CGO2 GB has securely been ed into the sli
13. ve the Batteries from service DO NOT continue to handle attempt to use or ship the Batteries Failure to follow these procedures can cause damage to Batteries personal property or cause serious injury Damaged or swollen Batteries can be unstable and very hot DO NOT touch batteries until they have cooled Dispose of batteries in the manner required by your city county state or country Contact the appropriate Yuneec Product Support Office to speak to a service technician for more information In the event of fire a Class D dry chemical fire extinguisher must be used then batteries must be placed inside of an approved Li Po bag Additional Guidelines and Warnings e In the event of a crash always quickly and safely disconnect and remove Batteries from the model Then follow the previously listed safety procedures e f the internal contents of Batteries come into contact with your skin wash the affected area s with soap and water immediately If it comes into contact with your eye s flush them with generous amounts of water for 15 minutes and seek immediately medical attention INSTALLING THE AA BATTERIES WARNING Alkaline Batteries May explode or leak and cause burn injury if recharged disposed of in fire mixed with a different battery type inserted backwards or disassembled Replace all batteries at the same time Do not carry batteries loose in your pocket or purse Do not remove the battery label STEP 1 Remove the Ba
Download Pdf Manuals
Related Search