PRODUCT MANUAL
Contents
1. ASSEMBLY WIRING HARNESS FOR CIRCUIT BREAKER 1 A641 ASSEMBLY CORD 115V 1 B057 BLOCK SPRING 1 B410 BREAKER THERMAL 1 2 A 1 C107M COVER OUTSIDE 203 1 C108M COVER OUTSIDE 266 1 G006 GEAR DRIVE ECO 1 H072 KNIFE HOLDER SS 1 1004 INSULATOR SWITCH PAD 1 K006 KNIFE ECO 1 K012 KNOB HANDLE 2 NO011 NUT 4 40 BRASS 2 P029 ROLL PIN 1 8 X 9 16 SS 18 8 1 R023 STRAIN RELIEF ELECTRIC CORD 2 S049 SCREW 10 32 X 3 8 SS HEX HEAD 2 S061 SCREW 8 32 X 25 HEX HEAD SS 1 S145 SPACER KNIFE HOLDER 1 S161 SPRING KNIFE BLOCK 1 S166 SPRING ENGAGEMENT RETURN 2 S167 SPRING TENSION 1 S196 STUD ECO KNIFE 1 S229 SWITCH LEAF 1 S760 SCREW 10 32 X 3 8 SS HEX HD INDENTED HEX 2 T021 TRACK SLIDE 1 W018 WASHER 10 LOCK PLATED 2 W019 WASHER 4 INTRL TOOTH LOCK SS 1 W034 WASHER DRIVE GEAR SPACER 0 010 THICK 1 W140 WASHER DRIVE GEAR SPACER 0 005 AS NEEDED 1 W141 WASHER DRIVE GEAR SPACER 0 003 AS NEEDED Please read thoroughly before operation and keep for future reference PRODUCTS FOR FOODSERVICE M090 REV D Edlund Company 159 Industrial Parkway Burlington VT 05401 802 862 9661 www edlundco com Edlund PRODUCTS FOR FOODSERVICE M090 REV D Edlund Company 159 Industrial Parkway Burlington VT 05401 802 862 9661 www edlundco com 203 266 Electric Can Opener Exploded View 230 V USE LOCTITE BLUE ON 10 32 THREADS 2 SEE ES232 203 SEE ES262 266 AS NEEDED L S760 018 GROUND SCREW Ple2. a damp cloth after every use to remove the build up of food residues Coat the drive gear with vegetable oil to prevent rusting If the drive gear starts to slip on the bead of the can its teeth may be worn To replace it give the gear a quick rap counter clockwise with Edlund gear removal tool T140 until it can be removed otherwise turning the gear will only rotate the motor then screw a new drive gear on clockwise until it is up against the output shaft shoulder Verify gap between gear and knife spacing Caution Thin spacers washers W034 W140 W141 are often used to control the gap or spacing between the knife and the gear Inspect the worn gear when removed to be sure spacer washers are not stuck to the gear If they are present clean them and return them to the output shaft behind the gear If for any reason the can opener does not function properly consult the troubleshooting guide for assistance or contact an authorized service agent Do not operate damaged can openers Please read thoroughly before operation and keep for future reference 4 Calund PRODUCTS FOR FOODSERVICE woo0REv pD Edlund Company 159 Industrial Parkway Burlington VT 05401 802 862 9661 www ediundco com V TROUBLESHOOTING A qualified technician should do all internal repairs Problem I Can opener will not start Cause 1 Cordset not plugged into outlet Correction 1 Plug cordset into grounded outlet with same voltage as listed
3. on rating label located on back of opener 2 Circuit breaker tripped 2 Reset breaker if breaker continues to trip replace breaker A640 3 Inoperative actuating switch 3 Replace switch S229 4 Motor may have failed 4 Check motor and replace as necessary with appropriate voltage motor geartrain 5 Broken wires or loose terminals 5 Check wiring for continuity and repair or replace as required 6 Broken two speed switch Model 203 only 6 Replace switch assembly and diode pak A2813P A586 II Can opener rejects cans 7 Cordset has broken wire 1 Clearance between back of knife and front of gear too large see sketch 7 Check for continuity and replace as required 1 With handle in locked down position check clearance between back of knife and front of gear using flat feeler gauge Clearance should be 0 001 0 005 Shim gear with W034 W140 or W141 washer to obtain clearance Use Edlund Tool T140 to remove knife gear 2 Motor actuates too soon 2 Screw down on S086 adjusting screw until motor comes on when bottom of knife is at top of gear teeth to half way down teeth of gear G006 3 Knifeholder is sticking 3 If knifeholder does not move all the way down switch will come on too soon Remove and clean knifeholder and mounting surface Lubricate with non sticking vegetable oil 4 Knife not rotating 4 Remove knife and knife stud cl
4. surface Lubricate with non sticking vegetable oil If knife still doesn t turn replace knifeholder H072 3 Burred edge on knifeholder can stop 3 Check knifeholder for burred edge or grooves on can stop Replace as required 4 Drive gear is slipping or milling removing metal from can bead 4 See Problem III 2 V Knife will not sever lid completely VI Cans will not fit under knife when can opener is off 1 Dull knife 1 Worn foot pads 1 Replace knife K006 1 Replace as necessary P001 2 Broken or weak return spring 2 Check return spring S166 and replace as required Please read thoroughly before operation and keep for future reference 6 Edlund PRODUCTS FOR FOODSERVICE M090 REV D Edlund Company 159 Industrial Parkway Burlington VT 05401 802 862 9661 www edlundco com 203 266 Electric Can Opener Exploded View 115 V GROUND SCREW wor8 SEE ES231 203 SEE ES261 266 Please read thoroughly before operation and keep for future reference 7 Callin 203 266 ASSEMBLY AND PARTS LIST 115V QTY PART NUMBER DESCRIPTION 1 A2813P ASSEMBLY SWITCH HI LOW 203 ONLY 1 A580DC ASSEMBLY LINKAGE ENGAGEMENT 1 A586 ASSEMBLY SPEED CONTROL DIODES 203 ONLY 1 A587 WELDMENT BASE CHANNEL 1 A588DC ASSEMBLY MOTOR GEAR TRAIN 115V 1 A640
5. 141 WASHER DRIVE GEAR SPACER 0 003 AS NEEDED Please read thoroughly before operation and keep for future reference 10
6. Edlund PRODUCTS FOR FOODSERVICE M090 REV D Edlund Company 159 Industrial Parkway Burlington VT 05401 802 862 9661 www edlundco com PRODUCT MANUAL MII MODEL MOING6 ELECTRIC CAY OPENER Please read thoroughly before operation and keep for future reference dlund PRODUCTS FOR FOODSERVICE M090 REV D Edlund Company 159 Industrial Parkway Burlington VT 05401 802 862 9661 www edlundco com SAFETY CAUTION SEVERED CAN LIDS HAVE CUTTING EDGES USE OF A PROTECTIVE GLOVE OR TONGS IS ADVISED WHEN HANDLING LIDS ANVARNING To avoid risk of electrical shock this slicer must be grounded and plug must not be altered Grounding Earthing Instructions Slicer MUST be grounded Grounding reduces risk of electric shock by providing an escape wire for the electric current if a electrical short occurs This slicer is equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet that is properly installed and grounded LABELS L009 Caution Label IMPORTANT CUTTING WHEEL MUST TURN FREELY ON STUD FOR OPENER TO OPERATE PROPERLY TO CLEAN REMOVE CUTTING WHEEL CLEAN AND OIL IT AND REPLACE BY TURNING STUD CLOCKWISE WITH SCREWDRIVER UNTIL STUD BOTTOMS ON HOLDER KEEP GEAR CLEAN BY BRUSHING TEETH LOO9 Please read thoroughly before operation and keep for future reference Calin PRODUCTS FOR FOODSERVICE woo0REv pD Edlund Company 159 Industrial Parkway Burlington V
7. T 05401 802 862 9661 www ediundco com I SPECIFICATIONS MODELNO B03 pe POWER SIZE 4 3 8 W X 7 D X 12 H 4 3 8 w X 7 D X 12 H 111mm x 178mm x 305mm 111mm x 178mm x 305mm WEIGHT 13 Ibs 5 85 kg 12 3 4 Ibs 5 75 kg ll CAN OPENER DESCRIPTION The Models 203 266 electric can openers manufactured by the Edlund Company are approved by the appropriate certifying organizations The two models differ only in that the model 266 can opener operates at a single speed while the model 203 can opener operates at the normal speed and a slower speed so that it is easier to open smaller or difficult to open cans The model 203 266 can openers are table type openers with a weighted base to offset the weight of a full No 10 can The external housing and knife holder are manufactured from stainless steel lll CAN OPENER OPERATION To operate plug the power cord into a grounded outlet with the same voltage as listed on the back of the can opener If you are opening a standard seven inch high no 10 can slide the can against the can opener drive gear and push the handle back to its locked down position The can opener motor will start after the can bead is captured between the knife and drive gear and before the knife pierces the can The can will start to rotate and after one full revolution the lid will be severed from the can After the lid is completely severed from the can pull the handle forward to stop th
8. ase read thoroughly before operation and keep for future reference O dlund PRODUCTS FOR FOODSERVICE wmosorREv pD Edlund Company 159 Industrial Parkway Burlington VT 05401 802 862 9661 www ediundco com 203 266 ASSEMBLY AND PARTS LIST 230V QTY PART NUMBER DESCRIPTION 1 A1040 COVER OUTSIDE 203 230V 1 A1045 COVER OUTSIDE 266 230V 1 A2831P ASSEMBLY HIGH LOW SWITCH 203 ONLY 1 A580DC ASSEMBLY LINKAGE ENGAGEMENT 1 A586 ASSEMBLY SPEED CONTROL DIODES 1 A587 WELDMENT BASE CHANNEL 1 A593DC ASSEMBLY MOTOR GEAR TRAIN 230V 1 A640 ASSEMBLY WIRING HARNESS FOR CIRCUIT BREAKER 1 B057 BLOCK SPRING 1 B410 BREAKER THERMAL 1 2 A 1 F088 FILTER EMI 1 G006 GEAR DRIVE ECO 1 H072 KNIFE HOLDER SS 1 1004 INSULATOR SWITCH PAD 1 K006 KNIFE ECO 1 K012 KNOB HANDLE 2 NO011 NUT 4 40 BRASS 2 P029 ROLL PIN 1 8 X 9 16 SS 18 8 2 S049 SCREW 10 32 X 3 8 SS HEX HEAD 2 S059 SCREW 6 32 X 25 HEX HEAD SS 2 S061 SCREW 8 32 X 25 HEX HEAD SS 1 S145 SPACER KNIFE HOLDER 1 S161 SPRING KNIFE BLOCK 1 S166 RETURN SPRING 2 S167 SPRING TENSION 1 S196 STUD ECO KNIFE 1 S229 SWITCH LEAF 1 S760 SCREW 10 32 X 3 8 SS HEX HD INDENTED HEX 2 T021 TRACK SLIDE 1 W018 WASHER 10 LOCK PLATED 2 W019 WASHER 4 INTRL TOOTH LOCK SS 1 W034 WASHER DRIVE GEAR SPACER 0 010 THICK 1 W140 WASHER DRIVE GEAR SPACER 0 005 AS NEEDED 1 W
9. e can opener motor If for some reason the lid is not completely severed or if the can is ejected from the gear consult the maintenance instruction and or trouble shooting guide later in this manual To open a shorter can the operator must support the can on his left or right hand place the bead or rim of can s top over the drive gear and push the handle back to its locked down position so that the can is held firmly between the knife and gear The supporting hand should then be removed completely from the can until the can lid us completely severed from the can If the operator restricts the rotation of the can by holding on to the can the can opener may reject the can After the can is opened pull forward on the handle and grasp the can simultaneously If a small can is not opened properly consult the troubleshooting guide CAUTION SEVERED CAN LIDS HAVE CUTTING EDGES USE OF A PROTECTIVE GLOVE OR TONGS IS ADVISED WHEN HANDLING LIDS Please read thoroughly before operation and keep for future reference 3 dlund PRODUCTS FOR FOODSERVICE M090 REV D Edlund Company 159 Industrial Parkway Burlington VT 05401 802 862 9661 www edlundco com IV CLEANING AND MAINTENANCE INSTRUCTIONS The can openers must be kept clean not only for the obvious reasons of sanitation but more important for operational reasons as well An electric can opener s rotary knife must rotate freely for the can opener to operate properly If the knife is bou
10. ean and lubricate using non sticking vegetable oil Replace knife and knife stud Knife must rotate freely Please read thoroughly before operation and keep for future reference 5 Edlund PRODUCTS FOR FOODSERVICE M090 REV D Edlund Company 159 Industrial Parkway Burlington VT 05401 802 862 9661 IM Drive gear will not turn can 1 Worn drive gear www edlundco com 1 Replace gear G006 Use Edlund Tool T140 to remove knife gear 2 Clearance between top of drive gear and radius at back of knife larger than 0 120 2 Check clearance If clearance is larger than 0 120 replace knifeholder H072 and check clearance If clearance still too large check linkage assembly Assembly A580DC may be worn 3 Bent knife stud 3 Replace stud S196 4 Worn knife stud hole in knife holder 4 Replace knifeholder H072 5 Gear in gear train broken loose from pinion 5 If motor runs but output shaft doesn t rotate replace as motor gear train as necessary PER VOLTAGE 6 Threaded hole in spring block B057 distorted 6 If linkage assembly not worn check for distorted hole in spring block IV Slivers found on can lid or in food product 7 Worn can stop on knifeholder 1 Factory knife edge altered or nicked 7 Replace knifeholder H072 1 Replace knife K006 2 Knife doesn t rotate 2 Remove knife from knifeholder clean knife knife stud and knife mounting
11. nd by residual food product the knife will not rotate and wear will not be distributed around the periphery of the knife More important than the wear a non rotating knife will no longer be shearing the metal can top as designed and metal slivers may occur The knife K006 should be removed often by unscrewing the knife stud S196 from the knife holder H072 so that the knife knife stud and knife holder can be properly cleaned Clean the knife holder by wiping off the knife holder protrusion with a damp cloth To greatly reduce the chances of the knife sticking and rusting after cleaning lubricate the knife stud knife holder protrusion and hub of the knife with vegetable oil Replace the knife with the smaller diameter hub meeting the machined boss of the knife holder Be sure the knife is rotating easily after parts are reassembled The factory made edge of the can opener knife is designed to shear through the metal can lid It will not function properly if allowed to become dull or nicked If knife becomes excessively dull it will be difficult to pierce the can and the knife will no longer sever the lid completely at the end of the cut Replace the knife when it becomes excessively dull or if nicks occur on the cutting edge Warning The can opener knife is not designed to be sharpened If the knife edge is made truly burr free it can shave off slivers The teeth of the drive gear must be clean and burr free Wipe off the drive gear with
Download Pdf Manuals
Related Search