User`s Manual XJ
Contents
1. This may overload the speakers Be sure to not set the volume too high 14 XJ 300FR Manual Earthquake Sound Corp www earthquakesound eu Connecting to Outdoor Speakers cont Wiring with the ROCK on 2 i channel system Series Wiring Subwoofer TR ANE This may overload the Ph an speakers Be sure to are not set the volume too Aa high Granite 52 Speakers Option 2 Though 1 XJ 300FR is capable of powering the Granite 2 1 system you can use 2 linked XJ 300FRs for more power Set the bridged amplifier to Low Pass to power the subwoofer and set the other amp to Bypass to power pier peakels WARNING This may overload the speakers Be sure to not set the volume too high INPUT a 6 On o 9 Ke AESA mg Q vs Granite 10D pingan Granite 52 Speakers Specifications are subject to change without notice XJ 300FR Manual 15 Connecting to SWAT 2 4 Wireless Transceiver Note Make sure the back input toggle switch is set to RCA if connecting to the SWAT 2 4 Version 1 The XJ 300FR is optimized for use with the SWAT 2 4 Wireless Transceiver After the amplifier is wired to the speakers connect the SWAT 2 4 Receiver to the RCA inputs on the XJ 300FR using a mi2. Included in the Box 1 XJ 300FR Stereo Class J Amplifier 4 Short Mounting Ears 1 Bracket 4 Screws for the Bracket 1 Power Cord Specifications are subject to change without notice XJ 300FR Manual 5 Front Features 1 Power Switch 1 Power Switch 3 Auto Music Sensing Switch to ON to turn Amplifier automatically on or to use the Auto on turns on when it senses music sensing feature signal POWER AUTO ON BYPASS LOWPASS AUTO OFF XJ 300FR Class J Stereo Amplifier 2 LED Light Green light signifies the amp is on In order to enable the auto on music sensing feature please see 3 3 To Enable Auto Music Sensing A Back toggle switch must be set to RCA the down position B Front toggle switch must be set to AUTO ON C Power switch must be set to ON D With signal amplifier comes on right away E When there is no signal for three minutes the amplifier shuts off 4 Bypass Lowpass Toggle Switch When set to Bypass it overrides the phase and crossover controls They are only to control low frequencies 5 Phase Setting If you are using the XJ 300FR to power a subwoofer you will need to set the arrival time of the subwoofer s frequencies to that of your speakers To do this with the highest accuracy you will need an SPL meter supplied at most electronics stores To set the phase A Send a 50Hz continuous tone signal through the spea
3. 1 hour of labor ongoing rates plus shipping back to the customer lt Each product sent for repairmust be packaged in its original packaging Otherwise there will be a repackaging charge in addition to labor parts and shipping charges C Earthquake agrees to repair or replace at our option all such defective products parts subject to the following provisions e Defective products parts have not been altered or repaired by other than an Earthquake factory approved technician e Products parts are not subjected to negligence misuse improper use or accident damaged by improper line voltage used with incompatible products or have its serial number or any part of it altered defaced removed or have been used in anyway that is contrary to Earthquake s written instructions D Warranty Limitations Earthquake warranty does not cover products that have been modified and or abused including but not limited to the following lt Damages to unit cover and finish due to misuse abuse or improper use of cleaning materials methods 18 XJ 300FR Manual Earthquake Sound Corp www earthquakesound eu 5 Year Limited Warranty cont e Bent casing damaged finish on casing due to abuse misuse or improper frame or broken connections e Fading deterioration of components and finish due to improper exposure to elements e Burnt tracers of PCB e Product part damaged due to poor packaging or abusive shipping conditions e
4. one rack space tall and has a half rack width chassis This smart design features a patented interlocking design so two XJ 300FRs can be connected side by side and be rack mountable Other amplifiers of the same size run too hot to mount them near anything else which defeats the purpose of their size Because the XJ 300FRs run completely cool you can comfortably mount other components directly above or below them in the rack This means ultimate convenience for the installer There are also additional mounting holes on the sides of the amplifier so that short brackets can be attached and the amp can be mounted directly to a wall or inside a cabinet Speaker Set up Options One or two XJ 300FRs can power a 2 1 channel system This depends on how much power you want to output to your speakers One XJ 300FR can be used for two speakers while the other can be bridged as a monoblock Alternatively you can use two linked XJ 300FRs as a 4 channel system For a more high powered system bridge both of them and designate one speaker or sub to one amplifier and another speaker or sub for the other The installer is completely in charge of how the amplifier s power is distributed Applications The XJ 300FR has countless applications because of how customizable the channel set up is If you need to install in ceiling speakers in the kitchen tower speakers in the living room or rock speakers outside the XJ 300FR can perform accurately in every situation
5. 1 16 w feet 1 7 8 Short Ear Specifications are subject to change without notice XJ 300FR Manual 17 5 Year Limited Warranty Earthquake warrants the original purchaser that the speaker or amplifier product is free from defects in material and workmanship under normal and proper use for a period of five 5 years from the date of purchase as shown on the original bill of sale with the serial number affixed written on it The five 5 years warranty period is valid only if the product is properly installed by an Earthquake authorized party and the warranty registration card is properly filled out and sent to Earthquake Sound Corporation If the product is installed by a non authorized party a thirty 30 days warranty period applies A Five 5 years limited warranty plan coverage guidelines If installed by an authorized Earthquake dealer e First year Earthquake pays for labor parts and ground freight only in the U S mainland not including Alaska and Hawaii back to the customer e Second year Earthquake pays for labor and parts only customer must pay freight both ways e Third fourth and fifth year Earthquake pays for labor only Customer must pay for parts and freight both ways B Warning e Products sent for repair that are tested by Earthquake technicians and deemed to have no problem will not be covered by the five 5 years limited warranty Customer will be charged a minimum of one
6. Corporation resulting from the five 5 years limited warranty policy must be resolved according to the laws and regulations of the county of Alameda California Specifications are subject to change without notice XJ 300FR Manual 19 BARI NGU AKE S OUND The Sound That Will Move You Earthquake Sound reserves the right to amend details of the specifications without notice Copyright Earthquake Sound Corporation Earthquake Europe Mogensensvej 29 5000 Odense C Denmark Phone 45 2043 8007 E mail support earthquakesound dk
7. Features 1 RCA Inputs 3 USB Port The most common Can receive both power audio input and signal 2 Input Toggle 4 Speaker Outputs Can be outputted to 2 speakers two speakers and a subwoofer or bridged to 1 channel 1 RCA Inputs If you are using the XJ 300FR as a mono block 1 channel amplifier connect only the left white RCA terminal Be sure the toggle switch is set to RCA in order to use this input 2 Input Toggle The XJ 300FR is capable of receiving signal through either the RCA or USB input Please note that the Auto on music sensing feature is only supported by the RCA input 3 USB Port Capable of receiving power and signal the USB port is optimized for use with the SWAT 2 4 Wireless Transceiver It uses the standard USB 5 5V Be sure the toggle switch is set to USB in order to use this input USB Port The four metal contacts enable the USB to be used for both power and signal The outer metal contacts receive the positive and negative currents while the inner metal contacts receive the left and right L R audio 5 5V 8 XJ 300FR Manual Earthquake Sound Corp www earthquakesound eu 5 110V 220V Option Should already be set to the correct voltage depending on your region 50 60Hz 110 120V 220 240V pl lo D JAN euno 110 120V FUS E T2AL 250V 220 240V FUSE T1AL 250V 6 Power Supply Comes with a replacement fuse directly under power inl
8. Subsequent damage to other products A warranty claim will not be valid if the warranty registration card is not properly filled and returned to Earthquake with a copy of the sales invoice E Service Request To receive product s service contact Earthquake Sound s service department at 510 732 1000 and request an RMA number Return Material Authorization item s shipped without a valid RMA number will be refused Make sure you provide us with your complete and correct shipping address a valid phone number and a brief description of the problem you are experiencing with the product In most cases our technicians might be able to resolve the problem over the phone thus eliminating the need to ship the product F Shipping Instructions Product s must be packaged in its original protective box es to minimize transport damage Shipper claims regarding item s damaged in transit must be presented to the carrier Earthquake Sound Corporation reserves the right to refuse improperly packed product s A copy of original sales receipt must accompany product s returned for service We encourage you to include a written description of the problem inside the package Ship product to Earthquake Sound Corp 2727 McCone Avenue Hayward CA 94545 USA Ph 510 732 1000 You are responsible for the cost of shipping the product to Earthquake Sound Corporation G Disputes Resolution All disputes between clients and Earthquake Sound
9. XJ 300 FR 2 Channel or Monoblock Class J Amplifier User s Manual ON POWER AUTO ON BYPASS PHASE CROSSOVER VOLUME N N N a sS oa gt olo ONO A N S Pa N AUTO OFF J LOWPASS 0 180 50Hz _160Hz MIN MAX 2a XJ 300FR Class J Stereo Amplifier D Digital Switching Power Supply EAR THOOARE i OI 0A 2 ol lo oo Earthquake Europe TIf 45 2043 8007 support earthquakesound dk www earthquakesound eu Earthquake Europe T Mogensensvej 29 FAP THUR 5000 Odense C Tel 45 2043 8007 S OUND The Sound That Will Move You Customer Support E mail support earthquakesound dk Web www earthquakesound eu www earthquakesound dk 2011 Earthquake Sound Corporation All rights reserved This document should not be construed as a commitment on the part of Earthquake Sound Corporation The information is subject to change without notice Earthquake Sound Corporation assumes no responsibility for errors that may appear within this document Safety Instructions Safety First This documentation contains general safety installation and operating instructions for XJ 300FR It is important to read this user s manual before attempting to use these products Pay particular attention to the safety instructions Symbols E
10. actors to consider before installing Earthquake Sound s XJ 300FR e What are the intended listening zones e What system options and accessories might be required for features such as local sources etc e From where in each zone will the listener prefer to control the system Where will the remote gains be located Where will the speakers be located e Where will the source equipment be located Connection Tips Keep all power cords away from all signal cables to prevent humming from induced noise e Choose reliable signal cable cords Earthquake Sound also specializes in high performance RCA cables and patches e All speaker wires that are ran through the walls should be twisted to reduce potential hum noise pick up e Label both ends of all wires with the corresponding room location e It is best to use a grounded electrical outlet to power the amplifier Lack of input ground reference could be unsafe Consult your electrical contractor about proper grounding 4 XJ 300FR Manual Earthquake Sound Corp www earthquakesound eu Introduction The XJ 300FR amplifier is an extremely versatile and modular amplifier It can be used as a two channel 2 1 channel or bridged as a 1 channel amplifier The XJ 300FR runs completely cool while outputting twice the power of most amplifiers its size Therefore it is extremely flexible and can be used in many different applications Multiple Mounting Options The XJ 300FR is only
11. e Sound Corp www earthquakesound eu Connecting to a Subwoofer Tactile Transducer Note Make sure the front toggle switch is set to Low Pass if connecting to a subwoofer or tactile transducer Wiring with the THOR In Wall Subwoofer Receiver Processor Wiring with the Q10B Tactile Transducer Receiver Processor CAUTION 4 WARNING SHOCK HAZARD DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Specifications are subject to change without notice XJ 300FR Manual 13 Connecting to Tactile Transducers Note Make sure the front toggle switch is set to Low Pass if connecting to a subwoofer or tactile transducer Wiring with 2 MQB 1 Tactile Transducers INPUT neurpower D QUTPUT A el Na ROANG J N E 110 120V FUSE T2AL 250V 220 240VFUSE T1AL 250V Do not wire 1 MQB 1 with the mono bridge setting Use either the left or right speaker output Connecting to Outdoor Speakers Note Make sure the front toggle switch is set to Bypass if connecting to speakers or a 2 1 channel system Wiring with AWS All Weather Speakers Receiver Processor
12. et 4 Speaker Outputs A To use the XJ 300FR as a two channel amplifier connect the right speaker to the R and R terminals and the left speaker to the L and L terminals B To bridge the XJ 300FR as a one channel amplifier or monoblock connect the positive speaker wire to the L terminal and connect the negative speaker wire to the R terminal Do not connect anything to the two lower black terminals C To use the XJ 300FR as a 2 1 channel amplifier connect the right speaker to the R and R terminals and the left speaker to the L and L terminals Then connect the subwoofer positive to the L terminal and the subwoofer negative to the R terminal 5 110V 220V Do not attempt to change the voltage setting The amplifier should already be set to the correct voltage depending on your region If not please contact your local Earthquake Sound dealer 6 Power Supply To access the 250V replacement fuse use a flat head screwdriver to pry off the plastic cover Specifications are subject to change without notice XJ 300FR Manual 9 Mounting Options for 1 XJ 300FR Wall or Anywhere Mountable The XJ 300FR can uniquely be mounted to a wall or inside a cabinet Simply screw in the four short ears to the matching holes on the sides of the amplifier chassis Then bolt to any vertical or horizontal surface The XJ 300FR also comes with four rubber feet to not damage the bottom in the instance that it simply sits on a s
13. helf or cabinet 10 XJ 300FR Manual Earthquake Sound Corp www earthquakesound eu Linking 2 XJ 300FRs The XJ 300FR s ingenious design lets the user link two amplifiers together depending on the desired channel set up 1 Match the bolts on the left side of one amp with the linking holes on the right side of the other amp 2 Once they are connected push the right amp forward while pushing the left amp backwards until they are locked together They are linked correctly when the faceplates are flush 3 Bracket the backplates of the amps together for added reinforcement WHEN LINKING THE AMPS DO NOT APPLY PRESSURE ONTO THE FRONTPLATES OR BACKPLATES THIS WARNING COULD DAMAGE THE TERMINALS KNOBS OR TOGGLE SWITCHES AMPS DAMAGED IN THIS WAY ARE NOT COVERED BY THE WARRANTY OUTPUT ONO M oN RA 110 120V O R CAUTION WARNING SHOCK HAZARD DONOT OPEN PA INPUT A 5 o e EE 5 OUTPUT NG MONO R O 110 120V iji N we 50 60Hz PEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Specifications are subject to change without notice XJ 300FR Manual 11 Mounting 2 XJ 300FRs Screw short mounting arms to the outer sides of the amplifiers so they are rack mountable JAAN NANDA NAN DANDA DANA AAAAAAAADAAAADAADAAANA E 12 XJ 300FR Manual Earthquak
14. kers and the subwoofer at the same time 6 XJ 300FR Manual Earthquake Sound Corp www earthquakesound eu 5 Phase Setting 7 Volume Setting Use to correct subwoofer Set based on the input frequency arrival times level and power rating of Can only use when in Low your load Pass setting PHASE CROSSOVER VOLUME Vt 0 180 Digital Switching Power Supply FAP TORE Ch 4 Bypass Lowpass 6 Crossover Setting Set to Bypass to use asa Room equalization for 2 channel or 2 1 channel subwoofer frequencies amplifier Set to Lowpass Can only use when in Low to use as a 1 channelor Pass setting subwoofer amplifier B Turn the phase knob to zero and place the meter in the listening position C While the system is playing the 50Hz tone read the meter D Rotate the phase knob until the meter reads the highest possible E Take note of the position for future reference 6 Crossover Setting As a rule of thumb A If you are powering the THOR In Wall SUB10 the Q10B tactile transducer or a large subwoofer 12 18 set the crossover to 50Hz 100HZ B If you are powering a MQB 1 tactile transducer a 10 subwoofer or small front speakers set the crossover to 70Hz or the 9 o clock position C If you powering a small subwoofer 8 or small speakers set the crossover to 100Hz or the 12 2 o clock position Specifications are subject to change without notice XJ 300FR Manual 7 Back
15. ni jack to RCA Y adaptor To power the SWAT 2 4 connect a USB cable from the SWAT to the amplifier SWAT 2 4 Wireless Receiver ee OUTPUT Mane R 50 60Hz O 110 120V 220 240V MO ean 7 0 i AEE AN _ WARNING SHOCK HAZARD DO NOT OPEN Connect the SWAT 2 4 Transmitter to your music source processor or computer with an RCA or mini jack output Be sure to power the SWAT with either the supplied wall wart or through the USB port Now you can wirelessly transmit audio to the XJ 300FR SWAT 2 4 Wireless Transmitter Note SWAT 2 4 Version 2 will be able to transmit both signal and power through its USB port thus eliminating the need Music Source for any RCA connection with audio output 16 XJ 300FR Manual Earthquake Sound Corp www earthquakesound eu Specifications Model No XJ 300FR Output Power 2 X 110 WRMS 8 Ohm Stereo 2x 170 WRMS 4 Ohm Stereo Mono Bridged 170 WRMS 110 volt AC 8 Ohm 210 WRMS 230 volt AC 8 Ohm 320 W IHF dynamic power 230 volt AC 4 Ohm Frequency Response 20Hz 20kKHz 0 08 Damping Factor Signal to Noise Ratio gt 97dB Power Line Voltage 110 120C AC 60Hz 180W 110 220V Input Sensitivity for max min 0 5V Full Output Input Impedance 10Kohm 3 8lbs 1 7kg Dimensions 8 chassis 9 1 2 including knobs 1 7 8 no feet 2
16. safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the pint where they exit from the apparatus Only use attachments amp accessories specified by the manufacturer Use only compatible rack or cart for final resting position Unplug this apparatus during lightening storm or when unused for a long period of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in anyway such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Specifications are subject to change without notice XJ 300FR Manual 3 Unpacking System Components e Keep the original carton and packing materials for future shipment or storage e Check for any visual signs of damage If you encounter any concealed damage consult your Earthquake Sound dealer before proceeding with unit installation e Retain the sales receipt as it establishes the duration of the limited warranty and provides information for insurance purposes System Installation Considerations There are several f
17. xplained Appears on the component to indicate the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock Calls attention to a procedure practice condition or the like CAUTION that if not correctly performed or adhered to could result in injury or death Calls attention to a procedure practice condition or the like WARNING F that if not correctly performed or adhered to could result in damage to or destruction of part or all of the product Note Calls attention to information that is essential to highlight 2 XJ 300FR Manual Earthquake Sound Corp www earthquakesound eu Safety Instructions 8 9 10 11 12 13 14 15 N Read these instructions in their entirety Store this manual and packaging in a safe place Heed all warnings Follow instructions do not take short cuts Do not use this apparatus near water Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatuses that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plus has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your
Download Pdf Manuals
Related Search