CNS-DPM2 User Manual v1.0 TABLE OF CONTENTS
Contents
1. Article 5 2 User Manual 10 TABLE OF CONTENTS INTRODUCTION SAFETY PRECAUTIONS PACKAGE CONTENTS HARDWARE OVERVIEW BASIC OPERATION STEP TIME MODE DISTANCE STOPWATCH MODE CALORIES ODO SET CALORIES DAY CALORIES MODE PULSE RATE MONITOR FUNCTION MOTION SENSITIVITY SWITCH ATTACHING DEVICE REPLACING BATTERY A NH NHN Thank you for purchasing CANYON CNS DPM2 multi functional yet fashionable pedometer equipped with latest technology designed specifically for sports active users You have made an excellent choice and we hope you will enjoy all of its exciting features To fully utilize the functions and features of CANYON CNS DPM2 please read through the user manual carefully before using the product and follow all of the procedures in the manual to fully enjoy all features of the product Introduction Safety Precautions Please observe all safety precautions before using the device Please follow all procedures outlined in this manual to properly operate the device e Do NOT attempt to disassemble or alter any part of the device that is not described in this guide e Do NOT place the device in contact with water or anv other liquids The device is NOT designed to be liquid proof of anv sort e In the event of liquid entrv into device interior immediatelv disconnect the device from the computer Continuing use of the device result in fire or electrical shock Please con2. detected e Please avoid placing excessive pressure on the pulse rate sensor The results might not be accurate e The device may take more than 10 seconds to correctly display the current pulse rate The pulse rate is measured with BPM Beat per minute unit Motion Sensitivitv Switch To adjust the device sensitivitv in regards to user motions slide the motion sensitivitv switch under the rear cover at the back side of device Note Experiment with different settings to fine tune device sensitivitv conforming to individual user Attaching Device CANYON CNS DPM2 is equipped with a clip that can be conveniently clipped onto either side of the hip portion of trousers or shorts For best results keep the unit in line with the Crease line of trouser pants Various actions may affect the accuracy of the step counting l The device isn t directiv perpendicular to the ground It is necessarv to position the device at least 60 degree to the ground Feet dragging walking with sandals or sandals like shoes or uneven footstep in a crowded area or uneven surface Inside a vehicle bicvcle motorcar train bus and other vehicles unexpected vibration might render the result differentiv Motion of standing up or sitting down Replacing Batterv 1 Unlock the batterv holder compartment releasing the screw Pull out the batterv holder Take out the old batterv and replace with a CR3032 3V batterv Pleas
3. e make sure the polaritv is aligned correctly as instructed on battery holder 4 Push the battery holder back into the device and fasten the screw
4. ss SET to confirm e PressUP CLR or DOWN to adjust user weight Press SET to confirm Press MODE to cycle through modes until DIST STW is displayed as shown Accumulated Distance Traveled is displayed at the top portion of the screen while Stop Watch Function is displayed at the bottom Press SET to begin counting timer Press SET again to stop and Press UP CLR to reset counting timer Calories ODO Mode Press MODE to through modes until KCAL ODO is displaved as shown Accumulated Calories Burned unit KCAL is displaved at the top portion of the screen while Accumulated Distance Traveled is displaved at the bottom Set Calories Dav Calories Mode Press MODE to cycle through modes until SETCAL DAYCAL is displayed as shown Target Calories is displayed at the top portion of the screen while Actual Daily Calories Burned is displayed at the bottom Press SET to adjust Target Calories Press SET to switch between digits and press UP CLR to adjust values e A bar scale located at the top edge of screen displays the Percentage of Target Calories Both Actual Daily Calories Burned and Percentage of Target Calories will be reset daily Pulse Rate Monitor Function Press Pulse to activate pulse reading mode Place a finger preferably the index finger on the pulse rate sensor located at the edge of CANYON CNS DPM2 The device automatically begins the pulse examination once the finger is
5. sult vour product distributor or the closest support center To avoid risk of electrical shock do not connect or disconnect the device with wet hands e Do NOT place the device near a heat source or directly expose it to flame e Never place the device vicinity of equipments generating strong electromagnetic fields Exposure to strong magnetic fields may cause malfunctions e Avoid exposing the device to extreme temperatures e Avoid taking a pulse reading while the finger is in direct sunlight Strong sun light will generate interference through the finger to the pulse sensor Package Contents Product I mage Item Name CANYON CNS DPM2 Main Unit User Manual 2 Driver Documentation CD Hardware Overview Scroll Up Scroll Down Pulse Sensor Clear Button Button Confirm Pulse Rate Mode Selection Button Button Button Motion Sensitivitv Switch Basic Operation Step Time Mode Press MODE to through modes until STEP TI ME is displaved as shown Step Count is displaved at the top portion of the screen while Time is displaved at the bottom Press SET to adjust time time format personal data setting e Press UP CLR or DOWN to toggle between 12Hr 24Hr time format Press SET to confirm e Press UP CLR or DOWN to adjust hours and minutes Hold the buttons for faster scrolling Press SET to confirm e Press UP CLR or DOWN to adjust stride distance Pre
Download Pdf Manuals
Related Search