User-Manual
Contents
1. Record the MAC address under the camera base before installing the camera 3 Hardware Installation First use the supplied screwdriver to loosen the four screws and detach the dome cover from the camera base Then follow the steps below to install the camera to either a ceiling or a wall Tamper proof Screw Remove the stoppers and route cables through the openings Rubber Stopper on the hole for Power amp IO Cables Rubber Seal Plug on the hole for RJ45 Ethernet Cable EN 3 English Connecting RJ45 Ethernet Cable RJ45 Cable Dimension unit mm Recommended cable gauge 24AWG 0 51 mm Rubber Seal Assembly Steps 1 Drill a hole on the rubber seal plug and in sert an Ethernet cable through the opening 2 Strip part of the sheath from the Ethernet cable 3 You will need an RJ45 crimping tool to attach the Ethernet wires to a connec tor When done connect the cable to the camera s Ethernet RJ45 socket o white orange stripe O orange solid g white green stripe B blue solid b white blue stripe G green solid br white brown stripe BR brown solid w ms omo Oo 4 Feed the Ethernet cable from the bottom of the camera and through the hole Attach the rubber seal plug for water proofing Connecting DC Power Cable 1 Add the supplied rubber washer to the cable as shown in the picture 2 Feed the cable from the bottom of the camera and ti2. salesusa vivotek com VIVOTEK Netherlands B V Busplein 36 1315KV Almere The Netherlands T 31 0 36 5389 149 F 31 0 36 5389 111 E saleseurope vivotek com
3. Green Q NOTE If DC power is preferred it should comply with O P 12VDC 1 5Amin L P S per IEC 60950 1 EN 7 English Power over Ethernet PoE When using a PoE enabled switch The Network Camera is PoE compliant allowing transmission of power and data via a single Ether net cable Follow the below illustration to connect the Network Camera to a PoE enabled switch via Ethernet cable Oo NOTE 1 This equipment is only to be connected to PoE networks without routing to outside plants 2 For PoE input connection use only UL listed I T E with PoE output PoE Switch When using a non PoE switch Use a PoE power injector optional to connect between the Network Camera and a non PoE switch PoE Power Injector optional Non PoE Switch ri EN 8 HARDWARE LIMITED WARRANTY What Is Covered This warranty covers any hardware defects in materials or workmanship with the exceptions stated below How Long Coverage Lasts This warranty lasts for TWENTY FOUR MONTHS from the date of purchase by the original end user customer What Is Not Covered This warranty does not cover cosmetic damage or any other damage or defect caused by abuse misuse neglect use in violation of instructions repair by an unauthorized third party or an act of God Also if serial numbers have been altered defaced or removed Further consequential and incidental damages are not recoverable under this war
4. X VIVOTEK FE8174V PERE nore QUICK llAsial a R ma English 58 fi B Fran ais Espa ol Deutsch Portugu s Italiano T rk e Polski Pyccku Cesky Svenska Dutch Dansk Indonesia y yall 5MP e 360 Surround View Vandal proof PoE SUPREME Warning Before Installation oO Power off the Network Camera as soon as smoke or unusual odors are detected oO Do not place the Network Camera on unsteady surfaces oO Do not insert sharp or tiny objects into the Network Camera a J Package Contents FE8174V For Mounting Plate For Camera Base Quick Installation Guide O Power amp I O Cables oO Refer to your user s manual for the operating temperature Do not touch the Network Camera during a lightning storm oO Do not drop the Network Camera Mounting Plate Screwdriver O N if Screws Desiccant Bag Double sided Tape Rubber Seal Plug Rubber Washer EN 1 Sold Separately in US amp Canada English Physical Description O Inner View Contacts for Internal Microphone B Lens Spring Contacts A Align B to A when attaching the dome cover Header J6 Header J7 Ethernet 10 100 RJ45 Socket Status LEDs Reset Button MicroSD SDHC SDXC Card Slot EN 2 Outer View IP66 rated Vandal proof Dome Cover Built in Microphone A IMPORTANT
5. circles on the sticker drill three holes into the ceiling Then hammer the three supplied plastic anchors into the holes 3 Arrange and feed the cables through the side of the mounting plate 4 Secure the mounting plate to the ceiling wall with three supplied screws 5 Connect the Ethernet cable to the socket 6 Connect two white headers to the J6 and J7 connectors 7 Attach the camera base to the mounting plate and turn counter clockwise as shown below Figure 7 1 Then secure the supplied screws to fix the camera base Figure 7 2 8 You will find a dessicant bag attached to the camera Replace the dessicant bag with the one shipped within the accessory bag 9 Attach the dome cover 10 Secure the four screws with the supplied stardriver Make sure all camera parts are securely installed You may also use the diagonal holes on the mounting plate marked as A B or C to install the camera to a standard 4 in junction box 4 Network Deployment General Connection without PoE 1 Connect RJ45 Ethernet cable to a switch 2 Connect the power cable from the Network Camera to a power outlet 3 If you have external devices such as sensors and alarms make the connection from the general I O terminal block 3V3 Power 3 3V DC DO Digital Output DI Digital Input GND Ground e General I O Terminal Block Power Cord Socket Black gt map Microphone In Pink Audio Out
6. ghten the plastic base for waterproofing r NOTE Connect the supplied power amp IO cables if your switch does not support PoE EN 4 Ceiling Wall Mount without Mounting Plate Choose this mounting type if you want to feed the cables form the bottom of the camera 1 2 NOOR W Attach the supplied alignment sticker for camera base to the ceiling wall Using the three circles on the sticker drill three pilot holes into the ceiling Then hammer the three supplied plastic anchors into the holes Drill a cable hole on the ceiling wall and feed the cables through the hole Connect the Ethernet cable to the socket Connect the two white header connectors to the J6 and J7 connectors Secure the camera base to the ceiling wall with three supplied screws You will find a dessicant bag attached to the camera Replace the dessicant bag included in the camera with the one shipped within the accessory bag Attach the dome cover Secure the four screws with the supplied stardriver Make sure all camera parts are securely in stalled r NOTE Arrange the cables neatly to avoid getting in the way when the dome cover is attached EN 5 English Ceiling Wall Mount with Mounting Plate Choose this mounting type if you would like to feed the cables form the side 1 Attach the supplied alignment sticker for the supplied mounting plate to the ceiling wall 2 Using the three
7. ranty What VIVOTEK Will Do VIVOTEK will in our sole discretion repair or replace any product that proves to be defective in material or workmanship Any repair or replaced part of the product will receive a THREE MONTH warranty extension How To Get Service Contact our authorized distributors in your region Please check our website www vivotek com for the information of an authorized distributor near you Your Rights SOME STATES DO NOT ALLOW EXCLUSION OR LIMITATION OF CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE VIVOTEK INC 6F No 192 Lien Cheng Rd Chung Ho Taipei County Taiwan www vivotek com 1 Proof of the date of purchase is required In the event you can not render such document warranty will commence from the date of manufacture 2 Cosmetic damage will only be covered by this warranty if such damage has been existed at the time of purchase AR 168 P N 625023301G Rev 1 1 All specifications are subject to change without notice Copyright 2014 VIVOTEK INC All rights reserved VIVOTEK INC VIVOTEK USA INC 6F No 192 Lien Cheng Rd Chung Ho New Taipei City 235 Taiwan R O C 2050 Ringwood Avenue San Jose CA 95131 T 886 2 82455282 F 886 2 82455532 E sales vivotek com T 408 773 8686 F 408 773 8298 E
Download Pdf Manuals
Related Search