WAT-01U2
Contents
1. IMAGE SENSOR FRONT FACE The light receiving face of the image sensor Dirt water or oil deposits on the image sensor will cause an unclear picture on the monitor Attach the lens cap to protect the lens and the sensor from contamination and damage LENS MOUNT e Mount for the lens CS mount FINE FOCUS ADJUSTMENT SCREWS There are 3 hex adjustment screws each placed at intervals of 120 for fine focusing of the lens MOUNTING FEATURES e Two mounting holes for M2 fasteners located on each of the top and bottom surfaces USB mini B CONNECTOR e For USB connection GPIO CONNECTOR e General Purpose Input Output connector Please refer to the User s Manual Set up and Operation 1 Ensure that the power to the WAT 01U2 and the peripheral equipment is turned off before making any connections 2 Remove the lens mount cap from the WAT 01U2 and attach the CS mount lens Use the optional C mount adaptor 30CMA R when a C mount lens is used 3 Connect WAT 01U2 with the PC using an attached cable 4 Start the software application and adjust the lens while viewing the image displayed If further focus adjustment is required use the hex wrench included and loosen the FINE FOCUS ADJUSTMENT SCREWS and rotate the lens to adjust the focus After completion of adjustment please make sure that the screws are securely fastened About tripod adaptor If using the mounting bracket2. included please refer to the figure below and secure the bracket to the camera using the M2x6mm screws included lt Adaptor Installation Example gt lt Tripod adaptor Options To purchase these options please contact the distributor or dealer from which you purchased the WAT 01U2 Q RT HF fa A miT RFE BERA AEA EROE Me OL Oe Oe C mount Adaptor 30CMA R This lens mount adaptor is used to convert a CS mount to a C mount OA RZA pA SMR ae Ae POSE ASS T 11363 2006 E A EERE T VARA FA SAEED EZA E A e p Ae EE SJT 11363 20064 E GEER R Ahha NRA RR r E E A cS RFF LDPE LDPE PP db 4 E 4 HF fet A S X EFRR TORE D A A A 4 Specifications Model WAT 01U2 1 2 8 inch CMOS image sensor 1984 H x 1225 V Sync System Internal Resolution H More than 680TVL Center YUY2 output Minimum Illumination 0 25 Ix F1 4 1 30s 160x120 176x144 320x240 i 640x480 1280x720 1280x800 1280x1024 1920x1080 30 fps CEPAP 1 15 1 30 1 60 1 120 1 250 1 500 AE mod 1 1000 1 2000 1 4000 1 8000 sec naag EI 1 30 1 8000 sec Slow shutter 1 15 1 8000 sec 0 42dB 0 24dB 25 steps ATW 2800 9500K MWB 2800 6500K BaCk Agnt ON Center OFF Compensation Power Supply DC 5V Supplied by the USB bus Operating Humidity Less than 95 RH Without condensation 30 70 C Less than 95 RH Without condensation Lens Mount CS mount
3. Back focus adjustable 32 W x 32 H x 23 D mm Min System Requirements 800MHz or faster 512MB or larger Others USB2 0 Port Recommended System Specifications CPU Intel Core i Series or newer 2GB or larger RAM Others USB2 0 Port 1920 lt 1080 or better resolution display Operation Confirmed OS Output size Windows XP 32bit 64bit SP2 SP3 with Limited Functions Windows Vista 32bit 64bit e Windows 7 32bit 64bit e Windows 8 32bit 64bit e Windows is a registered trademark of Microsoft Corporation in the United States Japan and other countries e Intel Core is a registered trademark of Intel Corporation in the United States and other countries e Design and specifications are subject to change without notice e Watec is not responsible for any inconvenience or the attendant damages to the video and monitoring recording equipment caused by misuse misoperation or improper wiring of our equipment e If for any reason the WAT 01U2 does not work properly or if you have any questions regarding installation or operation please contact the distributor or dealer from which it was purchased Contact information Walec Watec Co Ltd Add 254 2 Nihonkoku Daihoji Tsuruoka Shi Yamagata Ken 997 0017 Japan TEL 81 235 23 4400 FAX 81 235 23 4409 Email info o watec co jp URL _ http www watec co jp 5010Z00 Y2000001
4. USB Camera WAT 01U2 Operation Manual Waterc This Operation Manual covers safety camera functions installation and the correct operating procedure for the WAT 01U2 First we ask you to read this Operation Manual thoroughly then install and operate the WAT 01U2 as advised In addition for future reference we also advise safekeeping of this manual Please contact the distributor or dealer from which the WAT 01U2 was purchased if you do not understand the installation operation or safety instructions laid out in this manual Not understanding the contents of the Operation Manual sufficiently may cause damage to the camera Guide to the Safety Symbols The definitions of the symbols used in this operation manual are When you do not adhere to or take notice of the Danger sign it Danger may lead to a serious accident such as death or injury caused by fire or electric shock ere When you do not adhere to or take notice of the Warning sign it may Cause severe damage such as a physical injury When you do not adhere to or take notice of the Caution sign it Caution May incur injury and cause damage to peripheral objects in the immediate surroundings i Cautions for Safety The WAT 01U2 is designed to be used safely however if not used safely it may lead to a physical accident caused by fire and electric shock Therefore please keep and read the Cautions for safety below for protection against acc
5. d an installation position on a ceiling or wall when a camera stand or tripod is used e Do not move the WAT 01U2 with the cables connected Before moving the WAT 01U2 always remove the cable from the camera first e Avoid using the WAT 01U2 near any strong electro magnetic field After installing into main equipment if the WAT 01U2 is exposed to electromagnetic waves causing the monitored image to become distorted we recommend the camera be shielded by appropriate protective casing Problems and Trouble Shooting If any of the following problems occur when using the WAT 01U2 e An optimal picture cannot be obtained after checking that all the cables and connections are correctly in place e Smoke or any unusual odor emerges from the WAT 01U2 e An object becomes embedded or a quantity of liquid seeps into the camera housing e More than the recommended voltage or and amperage has been applied to the WAT 01U2 by mistake e Anything unusual occurring to any equipment connected to the WAT 01U2 Disconnect the camera immediately according to the following procedures wi i r h Remove the cables connected to the WAT 01U2 3 Contact the distributor or dealer from which the WAT 01U2 was purchased About EMC The WAT 01U2 is in conformity with EMC test standards carried out by authorized organizations in Japan FCC Part15 classA EN55022 EN55024 Compliance with EMC standards are confirmed using components peripheral accessor
6. idents e Do not disassemble and or modify the WAT 01U2 e Do not operate the WAT 01U2 with wet hands Danger e Do not expose the WAT 01U2 to wetness or high moisture conditions The WAT 01U2 is designed and approved for indoor use only The WAT 01U2 is not water resistant or waterproof If the location of the camera is outdoors or in an outdoor like environment we recommend that you use an outdoor camera housing e Protect the WAT 01U2 from condensation Keep the WAT 01U2 dry at all times during storage and operation AE Warning e Should the camera not work properly switch off the power immediately Then check the camera according to the Problems and Trouble shooting section e Avoid the striking of hard objects or dropping the WAT 01U2 Caution The WAT 01U2 uses high quality electrical parts and precision components e Do not connect any power supply directly to the video out terminal of the unit Do not connect the WAT 01U2 with any monitor using a video power single transmission terminal The WAT 01U2 is not designed for use with this type of equipment We also advise you to read the operation manual of the monitor you plan to use before any connections are made e Do not install the WAT 01U2 in a position subject to direct sunlight Sunlight shinning directly onto the WAT 01U2 lens can cause damage to the sensor e Select a stable place for installation of the WAT 01U2 Use a support of durable strength aroun
7. ies included with the camera Do not modify the WAT 01U2 A modified camera may not conform D to EMC test standards This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Watec Inc 1450 Route 300 Building 2 Suite 204 Newburgh NY 12550 USA TEL 1 845 359 1490 FAX 1 845 359 1391 Contents Using the contents figures below make sure all parts are present before use 0 ERX 2P cable Tripod adaptor L HEDE EE USB cable Lens Mount Cap WAT 01U2 Hex wrench Description of Parts O
Download Pdf Manuals
Related Search
WAT 01U2 wat-01u2