WASHING MACHINE USER MANUAL
Contents
1. All of these are dry cleaning symbols The letters are to instruct the cleaner what type of solvent to be used Garments bearing these symbols should not be washed in your machine unless the label says otherwise2. The program ready light and program end light blink The program start pause light ready light and program end light stays on permanently The start pause light program ready light and program end light blink The program ready light and program end light stays on permanently PROBABLE FAILURE The heater of your machine or the heat sensor has failed The motor has failed Configuration error The motor has failed The network voltage is too high or too low THE PROCESS TO BE DONE Shut down your machine and unplug Turn off your tap and apply to the nearest authorized service Shut down your machine and unplug Turn off the tap and apply to the nearest authorized service Shut down your machine and unplug Turn off the tap and apply to the nearest authorized service Shut down your machine and unplug Turn off the tap and apply to the nearest authorized service If the network voltage is lower than 150V or higher than 260V your machine will automatically stop When the network voltage is recovered your machine will continue its operation SECTION 10 INTERNATIONAL WASHING SIGNS ve o XA ge l o Washing Do not wash temparature hand wash Lukewarm iron Medium hot iron a 2 zs w Do not tumble dry A A Dry flat Do not bleach Handy to bleach Hot iron Do not iron Hang to dry
3. Nylon socks blouse 11 BABY WASH Baby laundry All baby laundry 12 SYNTHETIC 40 Slightly dirty synthetic or synthetic mixture textile Nylon socks blouse TABLE 1 PROGRAM DETERGENT COMPART MAX DRY LOAD CAPACITY kg TYPE OF LAUNDRY EXPLANATIONS 13 SPORT CLOTHES 2 3 Sport clothes All sport clothes and jeans 14 SYNTHETIC COLD Slightly dirty synthetic or synthetic mixture sensitive laundry W ashed without heating the tap water Nylon socks blouse 15 CURTAIN WASH Tulle and curtain as sensitive laundry Tulle curtain diolen dralon 16 DELICATE 30 Slightly dirty cotton coloured synthetic or synthetic mixture sensitive laundry 17 DELICATE COLD Very slightly dirty cold water with to wash cotton coloured synthetic or synthetic mixture sensitive laundry Silk mixture shirt blouse polyester poliamid mixture textile 18 HAND WASH Slightly dirty wash in hand cotton coloured synthetic or synthetic mixture laundry Hand wash to all laundry 19 WOOL 30 Dirty hand and machine to wash wool laundry 20 WOOL COLD 2 2 Very slightly dirty cold water hand and machine to wash wool laundry All wool laundry 21 RINSING When you need an additional rinsing to be done to your clothes after the washing process you can use this program for all kinds of clothes
4. Wait for 1 2 hours and rinse after wiping with a few drops of white vinegar Grass stain Rub the stained part with detergent If the type of fabric is suitable for use of lye wash it with lye Rub your woolen clothes with alcohol For coloured ones a mixture of 1 unit pure alcohol and 2 units of water Oil Paint The stain should be eliminated before it dries by applying thinner on it Then it should be rubbed with detergent and washed Burnt stain If your cloth is suitable for use of lye you can add lye into your washing water For woolen fabric a cloth damped in oxygenated water should be covered on the stain and it should be ironed with a dry cloth on it It should be washed after rinsing well KA add SECTION 8 AVOIDING MINOR FAULTS All repairing which must be done on the machine should be done by authorized service When a repairing is required for your machine or you are unable to eliminate the failure with the help of the information given below e Unplug the machine e Close the water tap e Apply to the nearest authorized service station FAILURE Your machine does not operate Your machine does not receive water Your machine is not draining water Your machine is vibrating PROBABLE CAUSE It is unplugged METHODS OF ELIMINATION Insert the plug into the Socket Your fuse is defected Change your fuse The electric power is off Check the electric power
5. 22 SPINNING When you need an additional spinning to be done to your clothes after the washing process you can use this program for all kinds of clothes 23 DRAINING This program is used to drain the dirty water inside after the washing process of your machine If you want the water inside your machine to be drained before the program ends you can use this program TABLE 1 CONTINUE You can use softeners in all programs except spinning and draining programs optionally When you arrange the quantity of the softener comply with the warning of the softener producer Fill your softener in its E softener compartment of the detergent drawer Energy label data based on programme tested in accordance with EN60456 Remove the water inlet hose Remove the filters found on the water inlet valves by using a pincer and wash thoroughly with a brush Clean the filters of the water inlet hoses located on the tap side by removing manually together with the seal After you clean the filters you can fit them the same way as you have removed PUMP FILTER The pump filter system elongates the life of your pump which is used to drain the dirty water It prevents lint to enter the pump Cleaning of your pump filter in every 2 3 months is recommended To clean your pump filter Open the kickplate s cover by pulling the handle Before opening the filter cover place a cup in front of the filter cover to prevent flow of th
6. Cancellation of the Program If you desire to end a running program early e Press the start pause button Turn the program knob to O off status Turn the program knob to Draining or Spinning programs The program ready light will be on Run the program you have selected by pressing the start pause button Program ending e Your machine will automatically stop when the program you have selected ends The program end light will be on Turn the program knob to O off position The door will be unlocked in approximately two minutes after the program ends You can open the door by pulling the handle of the door towards yourself and take out your clothes After you unload your clothes leave the door open to dry the interior of your machine Unplug your machine Close the water tap WARNING If the power is off end on again after a while on any stage of the washing program your machine will continue the program from the point where it was interrupted This is not harmful for your machine Child lock Child lock is used in order to protect the washing cycle from the effects of unwanted button activations during the cycle Child lock is activated by pressing the first and third button on the control panel at the same for more than 3 sec When child lock is activated LEDs on the function buttons blink to indicate that child lock is active In order to deactive child lock the same buttons 1st and 3rd should be pressed again for m
7. the cabinet of your machine with lukewarm water and a cleaning substance that will not irritate the cabinet After rinsing with clean water wipe it with a soft and dry cloth N WARNING If the machine is installed in a location where the ambient temperature can fall below 0 C do the following when it will not be in use e Plugin the machine e Close the water tap and pull out the water inlet hose or hoses from the tap Place the ends of the water drain and water inlet hoses in a cup on the ground Adjust the program knob to Draining program The program ready light will be on Run the program by pressing the start pause button Unplug your machine when the program is over program end light is on When you complete these proces the remaining water inside the machine will be drained and thus formation of ice in the machine will be prevented When you operate your machine again be sure that the ambient temperature is above 0 C THE DRUM Do not leave metal parts like needles staples or coins inside your machine These pieces cause formation of rust stains in the drum To eliminate these stains of rust use a cleaning substance without chlorium and follow the warnings of the cleaning substance producer For cleaning of the rust stains never use dish washing wires or similar rough objects REMOVE OF LIME FROM YOUR MACHINE If you arrange the amount of the detergent you use in your machine properly there will be no need for l
8. Cotton 60 4 Cotton 40 5 Eco wash 6 Cotton 30 7 Quick wash 8 Cotton cold 9 Mix wash 10 Synthetic 60 11 Baby wash A 12 Synthetic 40 13 Sport clothes swruen 14 Synthetic cold 15 Curtain wash 16 Delicate 30 17 Delicate cold 21 Rinsing 18 Hand wash 19 Wool 30 22 Spinning 20 Wool cold 23 Draining SECTION 5 WASHING YOUR LAUNDRY e Plug the machine e Open the tap water First wash cycle There may be water left inside your machine after factory tests and trials It is recommended that the first wash cycle should be made without any laundry so that carry out this water pour half a measuring cup of normal allpurpose detergent into compartment 2 and select cotton program at 90 C BEFORE WASHING Discrimination of your laundry Discriminate your clothes according to their types cotton synthetic sensitive woolen etc washing temperatures and level of dirtiness Never wash your white and coloured clothes together Since your new coloured clothes may shed dye on the first wash wash them separately Be careful that no metal pieces are found on or in the pockets of your clothes remove if there is any Zip and button your clothes Remove the plastic or metal hooks of the curtains and laces or place them inside a washing bag and tie e Pull the textiles like trousers knitted fabric t shirt and sweat shirt inside out e Wash your small clothes like socks and handkerchiefs in a washing bag Xe Was
9. Start pause button has not been pressed Press the start pause button The program knob is in O off status knob on the desired Bring the program status The door is not shut properly Water tap is closed Shut the door properly You should hear the click Open water tap The water inlet hose may be bent Check the water inlet hose The water inlet hose is obstructed Clean the filters of water inlet hose The valve inlet filter is obstructed Clean the valve inlet filters The door is not shut properly The drain hose is obstructed or bent Shut the door properly You should hear the click Check the drain hose The pump filter is obstructed Clean the pump filter The clothes are not placed inside the machine in a well balanced manner The feet of your machine are not adjusted Spread the clothes inside the machine in an orderly and well balanced manner Adjust the feet Transportation screws are not removed Remove transportation screws See the section concerning the maintenance and cleaning of your machine See the section concerning installations your machine FAILURE Your machine is vibrating Excessive foam in the detergent drawer The washing result is bad PROBABLE CAUSE There is a small amount of clothes in the device Excessive am
10. WASHING MACHINE USER MANUAL THE CONTENTS SECTION 1 BEFORE USING e Safety warnings e Recommendations SECTION 2 INSTALLATION e Removal of transportation screws e Adjustment of feet e Electrical connection e Water supply connection e Water drain connection SECTION 3 TECHNICAL SPECIFICATIONS SECTION 4 CONTROL PANEL Start Pause button Function indicator lights Function buttons Spin speed selector Program knob SECTION 5 WASHING YOUR LAUNDRY e Before washing e Running the machine SECTION 6 MAINTENANCE AND CLEANING e Water inlet filters Pump filter Detergent drawer Siphon plug The cabinet The drum Remove of your machine from lime SECTION 7 PRACTICAL INFORMATION SECTION 8 AVOIDING MINOR FAULTS SECTION 9 AUTOMATIC FAILURE DETECTION SYSTEM SECTION 10 INTERNATIONAL WASHING SIGNS SECTION 1 BEFORE USING SAFETY WARNINGS Do not use a multiple socket or extension cord Do not insert a plug with damaged or broken cord into the socket If the cord is damaged it should be replaced by the manufacturer or appointed service agent in order to avoid a hazard Never remove the plug from the socket by pulling from the cord section Remove the plug by holding Do not plug the power supply with wet hands Never touch the machine with wet hands or feet Never open the detergent drawer while the device is running Never force to open the door of the machine while the machine is running Since the machine can reach high temperature
11. and wipe with a sponge or soft cloth wetted in cold water Rub with detergent and wash with diluted lye Grease and oil stains First wipe the residues Rub the stain with detergent and then wash with lukewarm soapy water Mustard First apply glycerine to the stained area Rub with detergent and then wash If the stain still does not disappear wipe with alcohol On synthetic and coloured cloth a mixture of 1 unit alcohol 2 units water should be used Blood stain Lay your clothes in cold water for 30 minutes If the stain still does not disappear lay in mixture of water and ammonia 8 table spoons of ammonia in 4 liters of water for 30 minutes Cream ice cream and milk Lay your clothes in cold water and rub the stained area with detergent If the stain has still not disappeared apply lye on the fabric of your clothes in proper proportion Do not use lye on coloured clothes Mould Mould stains should be cleaned as soon as possible The stain should be washed with detergent and if it does not disappear it should be wiped with oxygenated water in proportion of 3 Ink Hold the stained area under cold water and wait until the inky water completely runs off Then rub with water diluted with lemon juice and detergent wash after waiting for 5 minutes Fruit Stretch the stained area of your clothes on the top of a container and pour cold water on it Do not pour hot water on the stain Wipe with cold water and apply glycerine
12. e remaining water in the machine Loosen the filter cover by rotating it counter clockwise and drain the water Remove the foreign materials from the filter Check for the rotation of the pump manually After you have cleaned the pump fit the filter cover by rotating clockwise Put the kickplate cover into the place Do not forget that if you do not fit in the filter cover properly it will leak water Z WARNING Danger of being scalded Since the water inside the pump maybe hot wait for it to cool A DETERGENT DRAWER Detergents may form a sediment in your detergent drawer or in housing of the detergent drawer in time To clean the sediment pull out the detergent drawer from time to time To pull out the detergentdrawer Pull the detergent drawer to the end DIAGRAM 1 Lift the front of the drawer continue to pull until the drawer is pull out DIAGRAM 2 Wash will an old toothbrush and excessiveamount of water Take off the leftover detergent avoid to drop into your machine After drying the detergentdrawer put into the housing in the same manner you pull out DIAGRAM 1 DIAGRAM 2 SIPHON PLUG Pull out the detrgent drawer Remove the siphon plug and clean the residues of the softener thoroughly Fit the cleaned siphon plug in its location Check if it placed properly THE CABINET Clean the exterior surface of
13. e your machine for a long time unplug your machine close the water supply and leave the door open in order to keep the inside of the machine dry and for prevention from unpleasant odour As a result of the quality control procedures a certain amount of water may remain in your machine This is not harmful for your machine SECTION 2 INSTALLATION You must pay attention to the following issues before using your washing machine REMOVAL OF TRANSPORTATION SCREWS Transportation screws which are located at the back side of the machine must be removed before running the machine Loosen the screws by rotating counterclockwise by a suitable wrench DIAGRAM 1 Remove the screws by pulling them DIAGRAM 2 To the holes where the transport screws have been removed insert the plastic transport screw taps found in the accessories bag DIAGRAM 3 The transportation screws that have been removed from the machine should be kept in hand for any other transportation necessities c y DIAGRAM 2 DIAGRAM 1 DIAGRAM 3 ADJUSTMENT OF FEET e Do not install your machine on rugs or similar surfaces e For your machine to work silently and without any vibration it should be settled on a flat non slippery and tough ground You can adjust the balance of your machine from its feet First loosen the plastic adjustment nut Adjust by rotating the feet upwards or downwards After the balance has been reached tigh
14. er SECTION 9 AUTOMATIC FAILURE DETECTION SYSTEM Your machine is equipped with systems which will both take the necessary precautions and warn you in case of any failure by controlling it self constantly during the washing processes FAILURE CODE INDICATOR The start pause light blinks FAILURE PROBABLE FAILURE The door is not shut properly THE PROCESS TO BE DONE Shut the door properly so that you hear the click If the problem persists turn off the machine unplug and apply to the nearest authorized service immediately FAILURE CODE FAILURE INDICATOR The program ready light blinks The start pause light and program ready light blinks PROBABLE FAILURE The water level in your machine is below heater The pressure of your water supply may be low or locking The pump has failed or the pump filter is obstructed THE PROCESS TO BE DONE Turn on the tap to the end Water may be cut check it If the problem is still continuing your machine will automatically stop after a while Unplug your machine turn off the tap and apply to the nearest authorized service Clean the pump filter If the problem persists apply to the nearest authorized service See the section regarding the maintenance and cleaning of your machine FAILURE CODE FAILURE INDICATOR The start pause light and program end light blink
15. h up tol 90 C Wash up to 60 C Wash upto 30 C Not washable in washing machine Placement of the clothes into the machine e Open the door of your machine e Fill your clothes in your machine in a well spread manner e Place each cloth separately e When you shut the door of your machine be careful that no cloth is jammed between the cover and the gasket Shut the door of your machine tightly otherwise your machine will not start the washing process Filling detergent in the machine The quantity of the detergent that you will fill in your machine depends on the following criteria e Your detergent consumption will change according to the dirtiness level of your clothes For your slightly dirty clothes do not pre wash and put a small amount of detergent in the compartment no 2 of the detergent drawer For your excessively dirty clothes select a program with pre washing fill portion of the detergent you will put in compartment 1 in the detergent drawer and the remaining portion in compartment 2 In your machine use the detergents developed especially for automatic washing machines The quantities that will be used for your clothes are written on the packing of the detergents As the hardness of your water increases the amount of the detergent to be consumed will also increase As the amount of your clothes increases the amount of the detergent to be consumed will also increase Fill your softener in the softener compartment in y
16. hine is not well balanced The end of the water drain hose is in a position too low according to the machine No failure The water is at the lower part of the drum The pieces of some detergents which do not dissolve in water may stick to your clothes as white stains These stains may be caused by oil cream or ointment METHODS OF ELIMINATION Put the clothes in your machine in a manner not to exceed its maximum capacity Use the amount of detergent according to the declaration of the detergent producer Spread the clothes inside the machine in an orderly and well balanced manner Place the water drain hose in an appropriate height By calibrating your machine for Rinsing program make an additional rinsing or eliminate the stains After drying with the help of a brush In the next washing operation use the maximum detergent amount declared by the detergent producer See the section concerning instalations your machine FAILURE The spining process is not done or starts with delay PROBABLE CAUSE No failure The unbalanced load control may works in that way METHODS OF ELIMINATION The unbalanced load control system will try to distribute your clothes in a homogenous manner After your clothes are distributed passage to spining process will be realized In the next washing process place your clothes into the machine in a well balanced mann
17. ime removal However if you desire to apply the removal procedure use the lime protectors in the market and pay attention to their warnings N WARNING The lime eliminating substances contain acids and this may cause colour modifications in your clothes along with an adverse effect on your machine SECTION 7 PRACTICAL INFORMATION a e o A Alcoholic beverages The stain point should first be washed with cold water than should be wiped with glycerine and water and be rinsed with water mixed with vinegar Shoe Polish The stain should be slightly scratched without ruining the cloth rubbed with detergent and rinsed In case it is not eliminated it should be rubbed with 1 unit of pure alcohol 96 degrees mixed in 2 units of water and then washed with lukewarm water Tea and coffee Stretch the stained area of your cloth on the top of a container and pour water as hot as the type of your cloth can endure on it If the type of your cloth is suitable wash it with lye Chocolate and cocoa By leaving your clothes in cold water and rubbing with soap or detergent wash it in the highest temperature that the type of your cloth can endure If there is still a stain of oil left wipe with oxygenated water in proportion of 3 Tomato paste After scraping the dried pieces without ruining the cloth leave in cold water for about 30 minutes and wash by rubbing with detergent Meat broth egg Eliminate the dried stain residues
18. n speed selector 5 Program reagy light 6 Program knob 7 Start pause button 8 Function buttons 9 Program end light START PAUSE BUTTON Used to start a selected program or pause during running N WARNING It is required for the program knob to be brought to O off position before selecting the program or changing a continuing program FUNCTION INDICATOR LIGHTS When the start pause button or any function button is pressed the C corresponding light turns on The light turns off when the function button or start pause button is re pressed or when the process the selected function is completed The function indicator lights are also used in failure detection system mentioned in section 9 FUNCTION BUTTONS Rinse hold This function is recommended to be used when the clothes cannot hr be taken immediately after the end of the program This will prevent occurrence of wrinkles When this button is pressed the last rinsing water is not drained For the program to continue from the same point repress the same button If you do not want your sensitive clothes to be spinned or you want them to be spinned sensitively turn the program knob to O off position Bring the program knob on one of the draining or spinning programs you desire and press the start pause button If the program you have selected is a drain program your machine will draining the water inside If you have selected a spinning program your machine will pe
19. ore than 3 seconds Deactivation of child lock is shown by blinking of LED on Start Pause button SECTION 6 MAINTENANCE AND CLEANING e Unplug your machine e Close the water tap WATER INLET FILTERS On the tap part of your machine s water inlet hose and at the ends of water inlet valves there are filters to prevent entrance of the dirt and foreign materials in the water to the machine If the machine is unable to receive sufficient water although your water tap is opened these filters should be cleaned PROGRAM DETERGENT COMPART MAX DRY LOAD CAPACITY kg TYPE OF LAUNDRY EXPLANATIONS 1 COTTON 90 6 Dirty boil cotton and linen textile 2 COTTON 60 PREWASH 6 Very dirty cotton coloured and linen textile 9 COTTON 60 Dirty cotton coloured and linen textile 4 COTTON 40 Slightly dirty paint to get out cotton coloured and linen textile 5 ECO WASH Dirty cotton coloured and linen textile 6 COTTON 30 Slightly dirty cotton coloured and linen textile 7 QUICK WASH Slightly dirty cotton coloured and linen textile 8 COTTON COLD Slightly dirty cotton coloured and linen textile Washed without heating the tap water 9 MIX WASH Dirty or very dirty stain cotton coloured and linen textile Underwears sheet table cloth t shirt shirt towel 10 SYNTHETIC 60 Dirty synthetic or synthetic mixture textile
20. ount of clothes are filled in the machine or the clothes are not placed ina well balanced manner Your machine touches a ripid object Too much detergent has been used METHODS OF ELIMINATION It does not prevent operation of the machine Do not exceed the recommended quantity of clothes and spread your clothes in the machine in a well balanced manner Prevent your machine s leaning on a tough place Press the start pause button In order to stop the foam dilute one table spoon of softener in half liter of water and pour it in the detergent drawer Press the start pause button after 5 10 minutes Arrange the amount of the detergent properly in the next washing process Wrong detergent has been used Your laundry too dirty for the program you have selected Use only the detergents produced for full automatic machines Select a suitable program see Table 1 The amount of detergent used is not sufficient Use more detergent according to the detergent FAILURE The washing result is not good The water is drained from the machine as soon as itis filled No water is seen in the drum during washing There are residues of detergent on the clothes There are gray stains on the clothes PROBABLE CAUSE Clothes exceeding the maximum capacity has been filled in your machine Your water may be hard Distribution of the clothes in your mac
21. our detergent drawer Do not exceed the MAX level Otherwise the softener will diffuse in the washing water via the siphon The softeners with high density should be diluted with some water before filling in the drawer That is because the softener with high density obstructs the siphon and prevents the flow of the softener e You can use fluid detergents in all programs without pre washing For this mount the fluid detergent level plate in the second compartment of the detergent drawer and arrange the amount of fluid detergent according to the levels on this plate RUNNING THE MACHINE Program selection and features Select the program and additional functions appropriate for your clothes from Table 1 Start Pause By pressing this button you can start the program you have selected or pause a running program Starting the program e Adjust the program knob to a program you desire e The program ready light will be on e f you want you can select one or more additional functions e Run the program which you have selected by pressing the Start Pause button Changing the program If you have selected a program and you do not want if to continue Press the start pause button Bring the program knob to O off status Adjust the program knob to the program you desire You can select the program that you desire from Table 1 The program ready light will be on By pressing the start pause button run the program which you have selected
22. rform a spinning operation and then end the program Extra rinse You can have one more rinsing done in addition to the rinses which your machine has made in all washing programs by using this function Easy ironing By using this function you can ensure your clothes to come out less wrinkled after the washing WARNING Functions vary depending on the model you have chosen If you forgot to use additional function and your machine starts to wash push the additional function button if the indicator light is on Additional function will be activated If the indicator light is not on additional function will not be activated SPIN SPEED SELECTOR By the spin speed selector knob you can make the adjustment of speed for the process of spinning your clothes The speed adjustment interval is between 0 No spin and the maximum spinning speed of your machine NOTE Do the spinning process of your sensitive and delicate clothes in the most appropriate mode PROGRAM KNOB With the program knob you can select the program with which you desire to wash your clothes You can adjust the program selection process by turning the program knob in both directions You must be careful that the adjustment sign of the program knob is exactly on the program you want to select When you bring the program knob to O off position while your machine is running your program will remain incomplete O Stop 1 Cotton 90 2 Cotton 60 Prewash 3
23. s while running do not touch the drain hose and water during draining In case of any failure first unplug the device and close the water tap Do not attempt to repair Please apply to the nearest authorized service station Do not forget that the packing material of your machine may be hazardous for children Do not let your children play with the washing machine Keep your pet away from your machine Your machine should only be used by adults within the information written in this manual Your machine is designed for use in house environment Warranty will be invalid if you use it for commercial purposes The appliance should not be put on a carpet which can block the air ventilation on the bottom side RECOMMENDATIONS The detergent or softener in contact with air for a long time will dry and stick to your detergent drawer To avoid this put your detergent and softener into the detergent drawer just before washing It is recommended that you use pre washing program for only very dirty clothes Please do not exceed the maximum loading capacity The appliance is not intended for use by people including children with reduced physical sensor yor mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a preson responsible for their safety Children should be supervised to ensure that they don t play with the appliance e f you will not us
24. ten the plastic adjustment nut again by rotating it upwards Never put cartons wooden blocks or similar materials under the machine to balance the irregularities on the level of the ground es aX ELECTRICAL CONNECTION Your washing machine works with 220 240V and 50Hz A special grounded plug has been attached to the network cable of your washing machine This plug must definitely be inserted to a grounded socket with 10 ampere The fuse flow value of the electricity line attached to this should also be 10 ampere If you have no such sockets and fuses in your house let it be made by a qualified electrician Our company will not be responsible for any damages that may occur as a result of usage without grounding WATER SUPPLY CONNECTION Depending on the features your machine may be with single water inlet cold or double water inlet cold hot The white headed hose is for cold water inlet and red headed hose is for hot water inlet valid for machines with hot amp cold water inlet To prevent leakage from the connection joints 1 valid for cold water inlet or 2 valid for machines with hot amp cold water inlet seals are included in the hose packing Fit these seals at the end of water inlet hoses on the tap side Connect the white headed hose to the water inlet valve with white filter and connect the red headed hose to the water inlet valve with red filter latter is valid in machines with hot amp cold
25. water inlet Tighten the plastic parts of the connections with your hand Please call a qualified plumber for safer connections Water pressure of 0 1 1 MPa from your tap will enable your machine to work more efficiently 0 1 MPa pressure means water flow of more than 8 liters in 1 minute from a fully opened tap After connections are completed check for the non leakage of the connection joints by turning on your tap completely Be sure that water inlet hoses are not folded broken or crushed Mount the water inlet hoses to a 3 4 geared water tap Cold water inlet White filter valve WATER DRAIN CONNECTION Be sure that water inlet hoses are not folded twisted crushed or elongated by stretching Water drain hose should be mounted at a height of minimum 60 cm maximum 100 cm from the ground The end of the water drain hose may directly be fitted to the dirty water outlet hole or a special apparatus mounted on the outlet bracket of the wash stand Never attempt to extend the water drain hose by adding extra parts c em e 9 Eu S idi NI SECTION 3 TECHNICAL SPECIFICATIONS Maximum dry laundry capacity kg 6 Recommended loading kg 5 5 Height cm 85 Width cm 59 6 Depth cm 54 Maximum spin cycles depend on the model you ve chosen SECTION 4 CONTROL PANEL PHILCO C 1 Detergent drawer 2 Start pause light 3 Function indicator lights 4 Spi
Download Pdf Manuals
Related Search