User`s Manual
Contents
1. LANID comprehensive TOOL for LAN installation and troubleshooting User s Manual CG Patent Pending Introduction Congratulations on your purchase of the LANID Network Device Identifier The LANID is the quintessential diagnostic tool for network installers andtroubleshooters working withsmall LANs Using the LANID network administrators can quickly confirm features of LAN devices and diagnose problems during LAN installation With a push of a button the LANID will determine whether the device you are testing whether it supports the following topologies andcapabilities Auto negotiation 1OOBASE Tx full duplex 100BASE Tx half duplex IOBASE T full duplex 10BASE T half duplex 100BASE T4 Moreover the LAN ID can also act as a network device negotiating with other LAN devices to determine faults The auto negotiation function provides automatic speed matching for multi speed devices allowing devices to configure to the best possible mode ofoperation over alink When linkedup with another LAN device the LAN ID will provide the following information about that device Whether the linkis up ornot Whether the deviceis transmitting apacket or not Whether the deviceis working infull duplex mode or half duplex mode Whether the deviceis operating in 100BASE Tx IOBASE T or 100BASE T4 mode Whether a datatransmission error has occurred The compact pen style design provides the user with optimum convenience an2. OO 3 LINK 100 F O O TX FULL 100H O HALF red 19 FE 3x 19 red 10HXE O ERROR 3 Flashing POWER oa
3. bps in full duplexmode Itis also transmitting an auto negotiation packet AUTO O 3 LINK 100F XE FE TX 10H Se j FULL green 10FO gg 100 green 10H O O ERROR LE POWER 4 The tested deviceis a 10 BASE T half duplex device linked at 10Mbps in half duplex mode and is communicating bad packets AUTOO XX LINK 100 F O O TX FULL 100 H O HALF red 10F O 3 19 red 10H J ERROR 4 POWER 5 The tested device is a 100 BASE T4 device capable of auto negotiation red AUTO X LINK 100F O O TX FULL 100H3 O HAIE 100 10F O er 10H O O ERROR POWER NOTE LANID does not Link with 100BASE T4 but it can advertise inthe Auto Negotiation 100BASE T4 operation 6 6 Thetested deviceis a 10 100 BASE TX capable of auto negotiation but isconfigured at 10Mbps green AUTOS 3 LINK 100F O O TX FULL green 100H O HALE aS Sane 10 e0 10 H J O ERROR te POWER NOTE If you configure a NIC as 10Mbps full duplex mode the device capability display willbe different fromthe above diagram depending on the NIC device driver This means yourcard is capable of 10 or 100 Mbps butyou are running the cardat only 10Mbps Youshould then reconfigure your card tothe maximize speed 7 The tested device is a 10 BASE T device butthe battery power is too lowto display reliableresults Atthis time youmust replace the battery witha newone AUT
4. d portability LANID Contents LANID Users manual Soft vinyl carrying pouch One 15cm Twisted pairs RJ45 cable One RJ45 to RJ45 coupler Product Profile Q PLUG TO HUB S JACK AUTO NEGOTIATION LED 10 100 BASE T GREEN LED 100 BASE T4 RED LED 00Mbps WITH FULL DUPLEX LED 00Mbps WITH HALF DUPLEX LED OMbps WITH FULL DUPLEX LED OMbps WITH HALF DUPLEX LED LINK LED TX LED FULL DUPLEX OR HALF DUPLEX LED 00 Mbps OR 10Mbps LED Q ERROR STATUS LED FOR NIC Network Interface Card JACK Q POWER LED POWER ON OFF SWITCH TEST KEY LEFT SIDE FOR DEVICE CAPABILITY INDICATOR RIGHT SIDE FOR LINK STATUS INDICATOR 80000000 ALTISVAVO Application 1 HUB Testing e Turn the power switch on and plug the LANID marked Hub into a hubport wall plate or patch panelthat you wishto test e Push the TEST button and readthe results e The LANID will determine the status of the port and display the capabilities of the device connected left hand side as well as the link status right hand side 2 NIC Network Interface Card Testing e Plug the providedpatch cable intothe NIC porton the right hand side ofthe LANID e Push the TEST button and readthe results e The LANID will display the capabilities of the NIC connected left hand side aswell as thelink status right handside elf you are not sure whether a HUB or NIC is connected on the other end you can push the TEST button to see if the gree
5. n LINK LED lights up e This will tell you that the cable is connected to an NIC or a Hub uplink port Features e EEE 802 3 compliant Fast Ethernet PHY negotiation e Power down mode significantly reduces power consumption e LED indicators test and monitor line connection status and determine features of the device being tested e RJ45 connector allows quick and easy connections to most network devices e Small handheld pen style casing allows for convenient application and portability Specifications Model number 256655 Connector type RJ 45 Recommended operation temperature 0 70 Power supply DC8V 2 AAA battery Power consumption 350 mW typical 100 4u W in Power Down Mode Display LED indicator Enclosure Durable plastic housing Dimensions 215x34x34mm LANID Signal Description O LED is off 3 LED ison 1 The tested device isa 10 100 BASE TX half full duplex device capable of auto negotiation and link ata speed of 100Mbpsin full duplex mode green AUTO X LINK 100 F 3 O TX 100H3 3 FULL green 10 Fe 3 100 green 10 HF ERROR 34 POWER 4 2 Thetested deviceis a 10 BASE T NIC without auto negotiation and link at a speed of 10Mbps in half duplex mode AUTO O J LINK 100 F O O TX FULL 100H O HALF red 100 10FO XE Grec 10 HJ O ERROR z POWER 3 The tested device isa 100 BASE TX full duplex device capable linked at100M
Download Pdf Manuals
Related Search