D-Link DCS-1130 User Manual
Contents
1. Configuration Setup gt Image Setup The options in Image Setup allow you to adjust the settings for your IP Camera sensor and image Your changes made for the image settings will be reflected immediately The results can be seen and found in the Live Video window below Brightness This adjusts the brightness of the camera image This is set to 60 by default Saturation This adjusts the color saturation of the camera image This is set to 60 by default Contrast This adjusts the contrast of the camera image This is set to O by default Frequency This option adjusts the camera sensor s setting to avoid the image flickering under certain light sources such as florescent lights This is set to 60Hz by default z w EN White balance You can change the white balance of the camera image E by selecting a setting from the dropdown box This is set to Auto by default SecuRITY B W Ticking this checkbox will change the camera image into black and white Flip This will flip the image vertically Mirror This will flip the image horizontally in such a way that your left side will be on the left side of the screen and vice versa Note Mirror and Flip can be used if you choose to mount the DCS 1130 upside down on the ceiling D Link DCS 1130 User Manual 19 section 3 Configuration Setup gt Audio and Video You may configure four video profiles with different settings for your camera You may also set up di2. information for your camera lt r jai O Static IP Address IP Address Subnet Mask IP Address Enter the IP address the camera should use Defaut Gateway Primary DNS Secondary DNS Enable UPnP Subnet Mask Enter the subnet mask that the camera should use E ee Default Gateway Enter the default gateway that the camera should n i use Primary DNS Enter the IP address of the primary DNS server that the aeiia camera should use Secondary DNS Enter the IP adress of the secondary DNS server that the camera should use Note If you need to use a static IP address and you do not know the network information contact your Internet Service Provider ISP for assistance D Link DCS 1130 User Manual 15 section 3 Configuration Enable UPnP Universal Plug amp Play UPnP allows Windows PCs to find Em this camera under Network Neighborhood without configuration Don t Save Settings Enable UPnP port forwarding If your router supports UPnP this will ee g V an cnar rar to ronan toe allow the camera to communicate which ports the camera needs to access the Internet so that the router can forward those ports automatically This DHCP Connection will enable you to access your camera over the Internet without having to jee patie configure your camera and router manually oa oaenoy j g Z Enable UPnP Enable PPPoE If you are using a PPPoE connection enable it and enter lemma the User Name and Passwo
3. Manual Ethernet port Connects to a PC or network through an Ethernet connection Power jack O Connects to the power adapter Section 2 Installation Installation Starting the Camera Setup Wizard Insert the Installation CD ROM into your computers CD ROM drive to start the autorun program The CD ROM will open the Camera Setup Wizard Simply click Start to go through the Setup Wizard which will help you through the entire installation process from connecting your hardware to configuring your camera Wireless N Network Camera DCS 1130 Welcome Welcome to the D Link Setup Wizard this will guide you through the setup of your D Link Camera Select your Language START Technical Support Troubleshooting D YiewCam p Manual Install Acrobat Advanced User Interfac D Link DCS 1130 User Manual Section 2 Installation Hardware Installation Attach the Antennas Screw the wireless antennas onto the antenna connectors E d i Connect the Camera to the Camera Base 1 Screw the two camera base pieces together 2 Screw the camera base into the mounting point on either the back or the bottom of the camera and tighten the collar g Li Ee tJ apace You can adjust the angle and pivot of the camera by loosening the a ani wheel and retightening it after moving it to the desired position _ gm D Link DCS 1130 User Manual Section 2 Installation Connect the Ethernet Cable Conne
4. RTSP port 554 C user authentication Don t Save Settings Note Be sure to take note of these settings since these same settings will be used to configure your router Note Some ISPs block traffic on commonly used ports like port 80 to disallow consumers from putting a server on their network Be sure to check with your ISP so that you can open the appropriate ports accordingly If your ISP does not pass traffic on port 80 you will need to change the Web server port the camera uses from 80 to something else like 800 If you are behind a residential gateway you will need to open a corresponding port on your gateway as well Not all gateways are the same Please refer to your gateway s user s manual for specific instructions on how to forward ports D Link DCS 1130 User Manual 4 Appendix A Installing the DCS 1130 on a Router Without UPnP Router Setup The following steps generally apply to any router that you have on your network The D Link DIR 301 is used as an example to clarify the configuration process Note Because a dynamic WAN IP address can change from time to time depending on your ISP you may want to obtain a Static IP address from your ISP A Static IP address is a fixed IP address that will not change over time and will be more convenient for you to use to access your camera from a remote location You can also use DDNS to obtain an IP address Please refer to page 18 for more information SETUP AD ANCED TOOLS S
5. home Unlike a standard webcam the DCS 1130 is a complete system with a built in CPU and web server that transmits high quality video images for security and surveillance The DCS 1130 can be accessed remotely and controlled from any PC Notebook over your local network or through the Internet via a web browser The simple installation and intuitive web based interface offer easy integration with your Ethernet Fast Ethernet or 802 11n g b wireless network The DCS 1130 also comes with remote monitoring and motion detection features for a complete and cost effective home security solution e Web based Recording to a PC s local hard drive no software required e Camera Setup Wizard technology simplifies setup by automatically configuring network settings e Includes D ViewCam 2 0 for multi camera monitoring and management e Motion detection to trigger recording and send e mail alerts e Administrator User password protection e 1 lux CMOS sensor for low light environments e 3GPP mobile surveillance e Simultaneous MJPEG and MPEG 4 streams allows optimization of both image quality and bandwidth efficiency e 802 11n g b wireless connectivity e WPS support for easy wireless network setup D Link DCS 1130 User Manual 1 Section 1 Product Overview Features e Simple to Use The DCS 1130 is a stand alone system with a built in CPU requiring no special hardware or software such as PC frame grabber cards Setup is simple with Camera Setup Wiza
6. recording and setting Prerecord to 5 seconds and Posirecord to 9 seconds the camera will save video from 5 seconds before motion was detected to 9 seconds after motion was detected Continuous This will set the camera to record continuously Scheduled Recording This will set the camera to automatically record video during the specified times in the table below After making any changes click the Save Settings button to save your changes or click the Don t Save Settings button to discard your changes D Link DCS 1130 User Manual 25 section 3 Configuration setup gt Snapshot Here you can set the camera to take snapshots when motion is detected Snapshots can be sent to an e mail address and or to an FTP server Enable Snapshot Check this box to enable the snapshot feature Event Based Motion Detection This will set the camera to take a Snapshot whenever motion is detected Continuous FTP only This will set the camera to take snapshots continuously at intervals specified in FTP Server gt Interval below You can only save to an FTP server when taking continuous snapshots Scheduled FTP only This will set the camera to take snapshots continuously at intervals specified in FTP Server gt Interval below according to schedule you define by checking days and entering the times you want to record between You can only save to an FTP server when taking scheduled snapshots D Link DCS 1130 User Manual DCS 1
7. will turn the camera s front LED indicator on or off After making any changes to this section click the Save button to save your changes D Link DCS 1130 User Manual Product DCS 1130 Here you can change the administrator s password for your account as well as add and or delete be z able i account s You can also configure a unique name for your camera and en its OSD On Screen Display feature in order to display camera name and time stamp for both live video and recordings of your camera 30 characters maximum 20 users maximum 30 characters maximum User et f Camera Name 36 characters maximum Enable OSD Label Show time v LED light 30 section 3 Configuration Maintenance gt System This screen allows you to save and restore the camera s current configuration You can also reset all settings to factory default or reboot the device Save To Local Hard Drive Click on the Save Configuration button to save the current configuration to a hard drive Save To Local Hard Drive Load From Local Hard Drive Load From Local Hard Drive To load a saved configuration click on the Restore To Factory Defaults Restore Factory Defaults Browse bution to select a configuration file from your hard drive Then er sa click the Load Configuration button to load the new configuration Restore To Factory Defaults Click this button to reset all settings to their factory defaults If
8. 130 e LIVE VIDEO setup MAINTENANCE STATUS Ren Recording In order to enable your camera to take oper iad EE nie ct the checkbox of Enable rider dlc Tia you can determine the trigger event s and FTP and or email notification s Don t Save Settings SNAPSHOT C Enable Snapshot Scheduling Event Based Motion Detection Continuous FTP only Scheduled FTP only Hours Minutes Hours Minutes Sun Start End Mon Start End Tue Start End Wed Start End Thu Start End Fri Start End 2 Sat Start End Send to E mail Address User Name Password SMTP Mail Server Sender E mail Address Recipient E mail Address Port range 1 to 65535 FTP Server User Name Password Host Name Path Filename Prefix 26 section 3 Configuration E mail Address When checked the camera will send the snapshots it takes to the e mail address specified in the following text boxes If you do not know what to enter for the User Name Password or SMTP Mail server contact your e mail service provider for details User Name Enter the username or login name for your e mail account Password Enter the password for your e mail account SMTP Mail Server Enter the SMTP server for your e mail account Sender E mail Address Enter the e mail address you want to appear as the From e mail address in the snapshot e mail Recipient E mail Address Enter the e mail address you want to send
9. Secondary DNS Enable UPnP E Enable PPPoE User Name Password Confirm password PORT DETAIL SETTINGS Save Settings Don t Save Settings 40 Appendix A Installing the DCS 1130 on a Router Without UPnP 3 Open the HTTP Port The HTTP port option under Port Detail Settings is used when multiple cameras are being installed behind a single public IP address and will be accessed remotely OR for using a port other than the default port for image viewing For each additional camera that is installed you must assign the appropriate Web server port for each camera to enable remote viewing By default port 80 Web server port is open If these ports are available for use you DO NOT have to open a second port and can proceed to the next section If port 80 is not available for example if you are already using port 80 to run a Web server or your ISP blocks access on port 80 you MUST open a second port and designate a new Web server port 800 801 802 etc Similarly if port 554 is not available you will need to open a different port for RTSP LIVE VIDEO SETUP MAINTENANCE STATUS HELP Setup Wizard SECURITY You can configure your LAN and Internet settings here Save Settings Don t Save Settings DHCP Connection O Static IP Address IP Address Subnet Mask Default Gateway Primary DNS Secondary DNS Enable UPnP E Enable PPPoE User Name Password Confirm password PORT DETAIL SETTINGS HTTP port 80
10. TATUS SUPPORT DEVICE INFO OG All of your Internet and network connection details are displayed on this page The firmware version is also displayed here Firmware Version 1 00 Nov 17 2006 MAC Address O00 17 9a 4d 8c e5 IP Address 192 168 0 1 Subnet Mask 255 255 255 0 DHCP Server Enabled MAC Address O0 17 9a 4d 8c e6 DHCP Client Disconnected IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 DNS WIRELESS 802 11G SSID dlink Channel 13 Encryption Disabled D Link DCS 1130 User Manual 42 Appendix A Installing the DCS 1130 on a Router Without UPnP 4 Use Port Forwarding to Enable Remote Image Viewing You will need to use port forwarding on your router to open ports for remote access to your camera This is sometimes referred to as Virtual Server Settings Please proceed as follows e Go to the Port Forwarding section of your router e Enter a Name for the port forwarding rule such as your camera name Enter your camera s IP address in the private local IP field select TCP under Traffic Type Enter the HTTP port your camera is set to use in the Start and End settings Note lf you are using more than one camera you will need to select a different public port for each camera If you cannot use port 80 for your public port for example if you are already running a web server select a different public port for your camera e Inthe Port Forwarding list a check mark a
11. User Manual DCS 1130 Version 1 0 Se Wireless N Network Camera Manual Overview This manual contains the following sections Section 1 Product Overview describes what is included with the DCS 1130 camera and things to consider before installing page 1 Section 2 Installation describes how to install the camera on your network page 7 Section 3 Configuration describes how to configure the settings on your DCS 1130 camera page 11 Section 4 Troubleshooting explains how to resolve common issues page 36 Section 5 Appendix contains special procedures and technical specifications page 39 D Link DCS 1130 User Manual D Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes Manual Revisions Revision Date Description May 08 2009 e DCS 1130 Revision A1 with firmware version 1 00 Trademarks D Link and the D Link logo are trademarks or registered trademarks of D Link Corporation or its subsidiaries All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies Copyright 2009 by D Link Corporation All rights reserved This publication may not be reproduced in whole or in part without prior expressed written permission from D Link Corporation D Link DCS 1130 User Manua
12. and the HTTP port number that you gave your camera htip lt ip address gt lt port gt To access your camera s video streams directly open your PC s device s web browser or media player and type in the IP address of the router given to you by your ISP a colon the RTSP port number that you gave your camera then the type of video stream you want to view as follows 3GPP stream mobile phone pda rtsp lt ip address gt lt port gt 3gpp For example if your camera s IP is 192 168 0 35 and you set the RTSP port to 100 rtsp 192 168 0 35 100 S8gpp To access your camera from a computer on your local home network simply enter the local IP address of your camera i e 192 168 0 35 If using a port other than port 80 you must enter the IP address followed by a colon and the assigned port number Note If your camera is connected to the Internet you can also use the Camera IP given to you on the stickers inside your box Viewing Your Camera Over the Internet Behind a Router If you want to view one of your cameras over the Internet and your PC is behind a router or firewall you may also need to activate port triggering This will allow you to open the necessary ports in order to view video from your camera Consult your router firewall s User Manual and use the following information to set up port triggering Port trigger 554 if you have changed the RTSP port on your camera use that number here o Ports to ope
13. ast Ethernet network e Wireless 802 11n g b network e An Internet connection e A router connected to your broadband modem Computer with the following e A PC with a wired connection to your router e Windows XP or Vista 32 64 bit e Internet Explorer 6 or higher with ActiveX controls enabled Computer with the following e Windows based operating system e An installed Ethernet adapter Browser Requirements e Internet Explorer 6 0 or higher e Firefox 1 5 or higher e Safari 1 0 or higher with Java 1 3 1 or higher Windows Users Make sure you have the latest version of Java installed Visit www java com to download the latest version Section 1 Product Overview Hardware Overview Front Focus ring Turning the ring will allow you to focus the camera Camera lens Records video from the surrounding area Reset Button Resets the camera tofactory defaults when pressed for 10 seconds Status LED Lights up and changes color to indicate the camera s status WPS Button Allows you to connect to a WPS router p Li nk q Camera microphone Picks up sound from the surrounding area D Link DCS 1130 User Manual Section 1 Product Overview Hardware Overview Back Antenna connectors Connects to the wireless antennas ETHERNET 5V 2 5A oco Camera base mounting points Allows you to attach the camera base or another mounting unit D Link DCS 1130 User
14. at you change 30 characters maximum the admin password for security purposes enpe Pasmo New Password Enter the new admin password 20 users maximum 30 characters maximum Retype Password Enter the new admin password again for verification After entering the new password again click on the Save button to save your changes Camera Name 11 36 characters maximum Add User Account The admin can create user accounts to allow others ER Label to log in to your camera to view the live camera feed or LED light User Name Enter the User Name you wish to use for the new user account New Password Enter the password for the new user account Retype Password Re enter the password for the new user account for verification After entering the password again click Add to add the new user account User List Here you can view the current list of users by using the dropdown box You can also delete a user by D Link DCS 1130 User Manual 29 section 3 Configuration selecting them with the dropdown box and then clicking the Delete button Device Setting Here you can change various other settings for your camera Camera Name Enter the name of your camera Enable OSD This will enable the information bar On Screen Display OSD to appear when viewing video Label This is the text label that will appear on the OSD Show time If checked the current time will be displayed on the OSD LED light This
15. changes D Link DCS 1130 User Manual 17 section 3 Configuration Setup gt Dynamic DNS If you have a DSL or Cable service provider that changes your modem IP address periodically Dynamic DNS Domain Name Service a method of keeping a domain name linked to a dynamic IP address is useful With most Cable and DSL connections you are assigned a dynamic IP address and that address is used only for the duration of that specific o ee connection With the DCS 1130 you can set up your DDNS service and e n the DCS 1130 will automatically update your DDNS server every time it Ema MMIII Enable DDNS receives a different IP address Depending on the service this update Server ates Host Name may take a few hours der name Password Verify Password Timeout Status Disable Enable DDNS Check this checkbox to enable the DDNS function of the camera SECURITY Server Address Use the dropdown box on the right to select a DDNS service Host Name Type in the Host Name of the DDNS service User Name Enter your User Name for the DDNS service Password Enter the password for the DDNS service Verify Password Retype the password for the DDNS service Timeout This sets the number of hours between DDNS updates Don t Save Settings After making any changes click the Save Settings button to save your changes or click the Don t Save Settings button to discard your changes D Link DCS 1130 User Manual 18 section 3
16. ct one end of the blue Ethernet cable included in your package to the Ethernet port on the back of the DCS 1130 camera Connect the other end of the cable to an available LAN port on your router or broadband modem WH AD Connecting to a router Connecting to a broadband modem Connect the Power Adapter Attach the power adapter to the power jack located on the back of the DCS 1130 and connect the power adapter to a power outlet After connecting the power adapter you should see the status LED on the front of the camera turn on The status LED will light red when it receives power will light green after the camera connects to the network and will flash green when the camera is being accessed D Link DCS 1130 User Manual 9 Section 2 Installation Connecting to a Wireless Network Using WPS lf your router Supports WPS connection you can connect your camera using the WPS button on the camera Press and hold the WPS button on the side of the camera for three seconds The status LED on the front of the camera will turn blue Press the WPS button on your router within 60 seconds The WPS button is usually on the front or side of your router On some routers you may need to log in to the web interface and then click on an onscreen button to activate the WPS feature If you are not sure where the WPS button is on your router please refer to your router s User Manual The DCS 1130 will then automatically create a wirel
17. ess connection to your router While connecting your camera s LED will flash and then your camera will reboot After rebooting the status LED on the front of the camera will turn solid green D Link DCS 1130 User Manual 10 section 3 Configuration Using the Configuration Menu After completing the Camera Setup Wizard you are ready to use your camera The camera s built in Web configuration utility is designed to allow you to easily access and configure your DCS 1130 At the end of the wizard click Go To Camera or enter the IP address of your camera into a web browser such as Internet Explorer To log in use the User name admin and the password you created in the Setup Wizard If you did not create a password the default password is blank After entering your password click OK Note If you are directly connecting your PC to the camera or if you are using the camera on a closed network the default IP is 192 168 0 20 D Link DCS 1130 User Manual 11 section 3 Configuration Web based Configuration Utility gaa oes SECURITY Use the following sections to set up and configure your network camera e LIVE VIDEO e SETUP e MAINTENANCE e STATUS e HELP D Link DCS 1130 User Manual section 3 Configuration Live Video Live Video gt Camera This section shows your camera s live video and event indicators You may select the available thumbnails for your options of predefined Video Profile Fu
18. fferent profiles for your computer and mobile display In addition you may configure the audio Speakers and microphone settings for your camera Encode Type This sets the video codec used for the video stream You can choose MPEG 4 or MJPEG JPEG Internet Explorer browsers can view both MPEG 4 and MJPEG video streams and non lE browsers can lt only view MJPEG video streams c Encode Type Resolution FPS MPEGS a 640x480 m 30o m 2Mbps m Resolution This sets the display resolution of the video stream If the Resolution is different than the Sensor Output size the video will be mm aao Loe e shrunken or enlarged to the Resolution size you set here aS FPS This sets the target number of frames per second FPS for the a m E eee video stream Higher frame rates will provide smoother video SEITE bps This sets the target bitrate of the video stream Higher bitrates will eae provide better quality video When the Encode Type is set to MJPEG you cannot change the bps setting Also available bps settings may change depending on what the Encode Type Sensor Output Resolution and FPS settings are set to Don t Save Settings JPEG Quality This sets the JPEG quality of any manual snapshots you take when this video profile is selected RTSP URL This setting allows you to set a suffix for your camera s RTSP URL So you can view your camera s video with this video profile s settings For example if
19. gt Network Setup cccceceseeeeeeeeeeeeees 15 Setup gt WITEI ESS cceccceecececeeeeeeeeeeeeeeeeeeees 17 Setup gt Dynamic LONG iiarcsncenteeeditonnastenonneees 18 Setup gt Image Setup ecceecceeeeceeeeeeeeeeees 19 Setup gt Audio and ViIdGO ccecceeeeeeeeeeeees 20 Setup gt Motion Detection ccceceeeee ecco es 22 Setup gt Time and Date cccccecceeeeeeeeeeeees 23 Setup gt Recording once secceaneceserauneneeweseceesseereee 24 Setup gt SnapShot eseseieenereernererrerrerrerreren 26 Maintenance siactcssatienconsmuctaaduntameccsey cos amneydcustennamaraties 29 Maintenance gt ACMIN cccccccceeceeeeeeeeeeeees 29 Maintenance gt System ccccceeceeeeeeeeeeeeeeees 31 Maintenance gt Firmware Upgrade 32 Status oo ccccccceccecceeeeeeeeeeeeeeeeeeeeeeuegeeeueeeeeeeneeeeeenes 33 Status gt Device INFO c ec eeceseeeeeeeteeeteeeeees 33 Status gt LOO i err ee ee 34 PCr sues AA E O ET 35 Troubleshooting ssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnn 36 Appendix A Installing the DCS 1130 on a Router Without UPNP iersnsisuinsdnisinnsniannn 39 Appendix B Technical Specifications 45 Section 1 Product Overview Product Overview Congratulations on your purchase of the DCS 1130 Wireless N Network Camera The DCS 1130 is a versatile and unique solution for your small office or
20. he section titled How to PING Your IP Address the IP address your Internet Camera is set to use If there is a reply it indicates that there is another device on the network with the same IP address You will need to run the Install Wizard again and change the IP address of the camera Other possible problems might be due to the network cable try using another network cable Test the network interface of the product by connecting a local computer directly to the unit utilizing a standard Crossover Cable and run the PING utility If the problem is not solved the Internet Camera might be faulty Internet Camera Installation 11 Why does the Power LED not light up Make sure that you are using the provided power supply for the Internet Camera and verify that the power supply is securely connected 12 Why does the Internet Camera work locally but not externally This might be caused by a firewall Check with your system administrator the firewall may need to have some settings changed in order for the Internet Camera to be accessible outside your local LAN Refer to page 39 for more information about installing your camera behind a router D Link DCS 1130 User Manual 37 section 4 Troubleshooting Make sure that the Internet Camera isn t conflicting with any web server you may have running on your network The default router setting might be a possible reason Check that the configuration of the router settings allows the Internet Camera
21. in this window first then enter the required settings Site survey Click the Rescan button to scan for available wireless networks After scanning you can use the dropdown box to select an available wireless network The related information SSID Wireless Mode Channel Authentication Encryption will be automatically filled EEE a crane ma oes eto tyrone in for you SSID The SSID of the wireless access point you wish to use Wireless Mode Use the dropdown box to select the mode of the wireless network you wish to connect to Infrastructure is normally used to connect to an access point or router Ad Hoc is usually used to connect directly to another computer Don t Save Settings SECURITY Channel If you are using Ad Hoc mode select the channel of the wireless network you wish to connect to or select Auto Authentication Select the authentication you use on your wireless network Open Shared WEP WPA PSK or WPA2 PSK Encryption If you use WPA PSK or WPA2 PSK authentication you will need to specify whether your wireless network uses TKIP or AES encryption If you use Open or Shared authentication this setting will be automatically set for you Key If you use WEP WPA PSK or WPA2 PSK authentication enter the Key also known as password used for your wireless network After making any changes click the Save Settings button to save your changes or click the Don t Save Settings button to discard your
22. l ji Table of Contents Table of Contents Manual Overview c cececeeeecececececececaseeeeeeeeeeeeseeeeaeaeaes Manual Revisions cecececececeeeeeeeecececeeeuseeesenenees i Trademarks 20 cc ececececececececececececececececeneceaeneneaeneneas ji Product OvervieW Qu cccececeecececueeeeececuseueeeeeuseueeeeeusaneeees 1 Features oo ccececececececeececececececeeeaeececeseeeaeeteceneneaeaeatens 2 Package Content cccsccccseeeeceeeseeeeeeeeeeseeeeees 3 System Requirements cccccseccceeceeeeeeeeeeeeeeeees 4 Hardware OvervieW 0ccccececcecececeecececeeeeaececeeaeaes 5 OMA EE E 5 Delo C 6 UELGLIE ie 9 eae nee en ee ere ee ne 7 Starting the Camera Setup Wizard c08 7 Hardware Installation ccececececececeeeeeesececeeeeeneaes 8 Attach the Antennas ccccecececececeeeeeeeeeeenenes 8 Connect the Camera to the Camera Base 8 Connect the Ethernet Cable anassen 9 Connect the Power Adapter c ssccseeeeeee 9 Connecting to a Wireless Network Using WPS10 Using the Configuration Menu esssseeseee 11 Web based Configuration Utility eee 12 Live Video cecccceecceeeeeeceeeeceeeeeeeeeaeeeeseueeteneeeseaees 13 Live Video gt Camera cccccceccseeeeeeeeeeeeeeeees 13 SS OID OE 14 Setup gt Wizard cateescctes astcecnesnsne eoctnnsaanevertanenssees 14 D Link DCS 1130 User Manual Setup
23. ll Screen mode and action items of taking Snapshot Recording Set Storage Folder Listen Talk and Digital Output You may also select your language setting using the drop down menu You can zoom in and out of the live video image using your mouse Left click to zoom in and right click to zoom out on the image Video Profile There are four different viewing profiles which you can configure in Setup gt Audio and Video Full Screen This allows you to view the video in full screen mode a ae To exit full screen mode press the ESC key on your keyboard Snapshot Click to capture a snapshot image The image will pop up in a new window You may save this image to a local hard drive Record Video Clicking this button will start or stop recording video to the file path specified with the Set Storage Folder button 8 Set Storage Folder You can change the folder where the video recordings will be saved O88 9 oss SECURITY Start Stop Audio This button toggles the built in microphone on and off allowing you to hear audio from the area surrounding your camera Audio is on by default D Link DCS 1130 User Manual 13 section 3 Configuration Setup Setup gt Wizard The setup wizard guides you through the initial setup of your IP camera You can use the Internet Connection Setup Wizard for initial network setup and you can use the Motion Detection Setup Wizard to set up motion detection and snapshots Sim
24. m Internet Explorer make sure ActiveX has been enabled in the Internet Options menu You may also need to change the security settings on your browser to allow the ActiveX plug in to be installed If you are using Internet Explorer version 5 or lower then you will need to upgrade your Web browser software in order to view the streaming video transmitted by the Internet Camera Also make sure that your anti virus program is not blocking ActiveX controls D Link DCS 1130 User Manual 38 Appendix A Installing the DCS 1130 on a Router Without UPnP Appendix A Installing the DCS 1130 on a Router Without UPnP If you connect your camera to an Internet router that does not support UPnP you can assign your camera to a DMZ connection on your router For more details refer to your routers User Manual for more details on configuring your camera to use a DMZ connection If you have multiple cameras you wish to connect or if you do not want to use DMZ follow these steps to allow multiple remote access to your cameras 1 Identify your camera on the network 2 Assign a local IP address and port for your camera 3 Determine your routers WAN IP Address Enable Remote Viewing 4 Open virtual server ports for your router Enable Remote Viewing 1 Identify Your Camera on the Network e Log in to your camera s web interface from a computer on the same local home network e Click on the MAINTENANCE tab and select Device Management e En
25. n 6970 6990 D Link DCS 1130 User Manual 44 Appendix B Technical Specifications Appendix B Technical Specifications Wireless Connectivity e 802 11 n g b Wireless with WEP WPA WPA2 Security e WPS Support System Requirements e Operating System Microsoft Windows 2000 XP Vista e Browser Internet Explorer Firefox Opera Networking Protocol Sensor e Pv4 ARP TCP UDP ICMP e inch color VGA CMOS Sensor e DHCP Client e NTP Client Lens e DNS Client e Focal length 5 0i1mm F2 8 e DDNS Client e SMTP Client Microphone e FTP Client e Signal noise ratio 40dB 3dB Omni directional e HTTP Server e Samba Client e PPPoE e RTP e RTSP e RTCP e 3GPP e UPnP Port Forwarding e 10 100BASE TX port e IEEE 802 3 compliant e EEE 802 3u compliant e Supports Full Duplex operation e MDI MDIX auto negotiation e 802 3x Flow Control support for Full Duplex mode D Link DCS 1130 User Manual Reset Button e Reset to factory default Video Codec e MPEG 4 MJPEG simultaneous dual format compression e JPEG for still image Video Features e Adjustable image size and quality e Time stamp and text overlay e Flip and Mirror e Fully configurable motion detection window Video Resolution e VGA 640 x 480 640 x 480 at 30fps 320 x 240 at 30fps 160 x 120 at 30fps 45 Appendix B Technical Specifications Audio Codec e GSM AMR 12 2Kbps e PCM 8Kbps Light Sensitivity e 1 lux F2 8 Digital Zoom e Up to 16X 3A C
26. n box to the right to select an NTP server to use or you can type one in Set date and time manually Check this checkbox to set the time and date manually You can then use the dropdown boxes to select the current Year Month Day Hour Minute and Second You can also click the Copy Your Computer s Time Settings button to automatically fill in the dropdown boxes with the current time and date from your computer After making any changes click the Save Settings button to save your changes or click the Don t Save Settings button to discard your changes D Link DCS 1130 User Manual 23 section 3 Configuration Setup gt Recording This option allows you to configure recording settings and scheduling Product D3 You can record video to a Samba network drive on your local network Enable recording Check this checkbox to enable the recording feature o eeror After enabling recording you will need to select a scheduling method praes ee nae Samba Auth Here select Anonymous if no user name or password is EEA caper required to access your Samba drive If you require a user name and sc password to log in to your Samba drive select Account and fill in the i E following information a o User name Enter the user name required to access your Samba el a ET AA drive l Password Enter the password required to access your Samba drive jpe A Password confirm Re enter the password required to access your sdnadaod Samba on Samba d
27. n zones After making any changes click the Save Settings button to save your changes or click the Don t Save Settings button to discard your changes D Link DCS 1130 User Manual 22 section 3 Configuration Setup gt Time and Date This option allows you to configure update and maintain the correct time on the internal system clock From this section you can set the time zone that you are in and set the NTP Network Time Protocol Server Daylight Saving can also be configured to automatically adjust the time when needed Time Zone Select your time zone from the drop down menu Enable Daylight Saving If your region uses a Daylight Saving adjustment check this checkbox soto daii Here you may configure the internal clock of your camera Auto Daylight Saving This option will adjust Daylight Saving Time Ea automatically an Time Zone GMT 12 00 International Date Line West Enable Daylight Saving Set date and time manually Selecting this will let you set the Daylight pzm Set date and time manually saving Time adjustment manually e Daylight Saving Offset This will set the Daylight Saving adjustment that will be used e Daylight Saving Date This will set the beginning and ending dates of the Daylight Saving period Synchronize with NTP Server Checking this checkbox will allow the camera to automatically synchronize its clock with an NTP server SECURITY NTP Server Use the dropdow
28. ntranet or Internet Other features include image monitoring recording images to a hard drive viewing up to 32 cameras on one screen and taking snapshots e Broad Range of Applications With today s high speed Internet services the DCS 1130 Wireless N Network Camera provides an ideal solution for live video over the Intranet and Internet for remote monitoring The DCS 1130 has a wide range of applications including industrial and public monitoring of homes offices banks hospitals child care centers and amusement parks e 802 11n Wireless Connectivity The DCS 1130 offers both 802 11n wireless and Ethernet Fast Ethernet connectivity making the DCS 1130 easy to integrate into your existing network environment The DCS 1130 works with an Ethernet based network for traditional wired environments and also works with 802 11n g b routers or access points for added flexibility D Link DCS 1130 User Manual 2 Section 1 Product Overview Package Contents If any of the above items are missing from your package please contact your retailer Note Using a power supply with a different voltage rating than the one included with the DCS 1130 will cause damage and void the warranty for this product D Link DCS 1130 User Manual Section 1 Product Overview system Requirements Network Requirements CD Setup Wizard Requirements Web based Configuration Utility Requirements D Link DCS 1130 User Manual e Wired 10 100 F
29. ontrol e AGC Auto Gain Control e AWB Auto White Balance e AES Auto Electronic Shutter Power e Input 100 240VAC 50 60Hz e Output 5VDC 2 5A e Powered by an external power adapter e Maximum power consumption DCS 1130 6 3W Dimensions WxDxH e 120 0mm x 81 5mm x 38 0mm without bracket and stand Weight e DCS 1130 280g without bracket and stand Operation Temperature e 0 to 40 C 32 to 104 F Storage Temperature e 20 to 70 C 4 to 158 F D Link DCS 1130 User Manual Humidity e 20 80 RH non condensing Emission EMI Safety amp Other Certifications e FCC Class B C e C Tick e CE 46
30. ply follow the instructions given in each step of the wizard to quickly set up your camera Alternatively you can manually set up your Internet connection by clicking Manual Internet Connection Setup and you can manually set up motion detection options by clicking on Manual Motion Detection Setup You can also see these settings by clicking on the menu on the left panel Network Setup Wireless Setup Motion Detection Snapshot D Link DCS 1130 User Manual SECURITY you wish to nually you may ET the Mn nte et Conne onfigure Setup to inpu ut the EEE O E section you can setup the IP camera s Motion Detection settings If you are configuring Paw ee cpr for the first time eect posing that you select the Motion Dete peen Wizard and follow the instructions AAN te pema configure Detection manually select the MA Moio DAENS Motion Detection Set Motion Detection Setup Wizard __ Manual Motion DetectionSetup 14 section 3 Configuration Setup gt Network Setup Network Setup allows you to configure your LAN and Internet configuration DHCP Connection This allows your camera to get an IP address automatically from your router or Internet service If you are not sure which LAN settings to use try using DHCP mode first You can configure your LAN and Internet settings here Save Settings gS Don t Save Settings Settings Static IP Address This allows you to manually set the IP address
31. ppearing before the camera name will indicate that the port forwarding rule is enabled e Click Save Settings to save your settings SETUP AD ANCED TOOLS STATUS SUPPORT PORT FORWARDING i EF SSE RILES SECAT ON re The Port Forwarding option is used to open a single port or a range of ports through your NETWORK FILTER firewall and redirect data through those ports to a single PC on your network WEBSITE FILTER Save Settings Don t Save Settings FIREWALL SETTINGS ADVANCED WIRELESS gy 10 PORT FORWARDING RULES ADVANCED NETWORK Application Name Computer Name Application Name Computer Name Application Name Computer Name Application Name A A A A A A A A A A A A A A A A Computer Name the same nt in both the Start and End fields A A Application Name You will need to repeat these steps to open an RTSP port for your camera port 554 by default D Link DCS 1130 User Manual 43 Appendix A Installing the DCS 1130 on a Router Without UPnP Viewing Your Camera Over the Internet After all settings have been entered correctly a user inside or outside your network will have access to the camera through a standard Web browser To access your camera simply type in the IP address of the router given to you by your ISP a colon
32. r enough buffer space for the camera to record with When storage is full When your storage device is full or has reached the free space limit specified in Record until you can choose to stop recording or you can have the camera delete old recordings to free space for new recordings to be saved Event Based Event based recording will allow you to record video when specific events happen Motion detection triggered recording Enabling this option will set the camera to record video when motion is detected by the camera Prerecord This will set how many seconds of video before the event takes place will be recorded Postrecord This will set how many seconds of video after the event takes place will be recorded RECORDING C Enable recording Record to Samba network drive Samba Auth User name Password Password confirm Server Shared folder Samba status Disabled Recording Options Resolution Record until MB of free space is left minimum is 32MB When storage is full Stop recording Overwrite older recordings Recording Method Event Based Motion detection triggered recording Prerecord seconds range 0 to 15 seconds Postrecord seconds range 0 to 15 seconds Continuous Samba only Scheduled Samba only Hours Minutes Hours Minutes Sun Start End Mon Start End Tue Start End Wed Start End Thu Start End Fri Start End Sat Start End Don t Save Settings Example Using motion detection triggered
33. rd for your PPPoE account You can get this a information from your Internet service provider ISP HTTP Port This is the port that allows the user to connect to the camera s user interface By default the port is set to 80 You may change the port number if using multiple cameras SECURITY RTSP Port This is the port that you use for RTSP streaming to mobile devices or PDAs By default the port is set to 554 You may change the port number if using multiple cameras Note You MUST also set up your router gateway for Port Forwarding Mapping this will enable remote viewing of your camera via the Internet Please refer to your routers instruction manual on how to open up ports For additional help on configuring your camera to work with your router please refer to Appendix A Installing the DCS 1130 on a Router Without UPnP on page 39 For installing multiple cameras ONE port per camera must be opened on your router the Web server HTTP port Also some browsers may restrict some ports such as 1 or 22 for security purposes If you have problems accessing your camera through HTTP try using a port higher than 1024 After making any changes click the Save Settings button to save your changes or click the Don t Save Settings button to discard your changes D Link DCS 1130 User Manual 16 section 3 Configuration Setup gt Wireless To set up your IP camera s wireless network interface settings enable Wireless Settings
34. rd technology which helps automatically configure your camera s network settings eliminating the need to set complicated settings on your router e Supports a Variety of Platforms Supports TCP IP networking HTTP and other Internet related protocols It can also be integrated easily into other Internet Intranet applications because of its standards based features e Remote Snapshot Images and Recording Using the snapshot and recording features you can save snapshots and record video and audio directly from the Web browser to a local hard drive without installing any software making it convenient to instantly capture any moment from a remote location e Record Directly to a NAS The DCS 1130 allows you to record directly to a local network area storage device without the use of a dedicated PC for storing recorded video e Low Light Recording The DCS 1130 s 1 lux light sensitivity allows you to capture video in rooms with minimal lighting making it ideal for use in low light environments e Web GUI Configuration Using a standard Web browser administrators can configure and manage the Network Camera directly from its own Web page via the Intranet or Internet This means you can access your DCS 1130 anytime from anywhere in the world e Remote Monitoring Utility The D ViewCam application adds enhanced features and functionality for the Network Camera and allows administrators to configure and access the Network Camera from a remote site via I
35. ring the installation and operation of the DCS 1130 Read the following descriptions if you are having problems The examples below are illustrated in Windows Vista and XP If you have a different operating system the screenshots on your computer will look similar to the following examples 1 What is an Internet Camera An Internet Camera is a standalone system that connects directly to an Ethernet or Fast Ethernet network and supported by the wireless transmission based on the IEEE 802 11g standard whereas conventional PC Cameras require connection to a powered PC to function An Internet Camera is an all in one system with a built in CPU providing a low cost web based solution that can transmit high quality video images for monitoring The Internet Camera can be managed remotely and can be accessed and controlled from any PC locally or through the Internet via a Web browser 2 What is the maximum number of users that can be allowed to access DCS 1130 simultaneously The maximum number of users that can log onto the Internet Camera at the same time is 10 Please keep in mind that overall video performance will slow down when multiple users are logged on 3 What algorithm is used to compress the digital image MPEG 4 and MJPEG are used to provide high quality images at low bandwidths 4 Can I capture still images from the Internet Camera Yes You may record snapshots using the snapshot feature on the Home page When viewing this page pres
36. rive for verification er eo Server Enter the name or the IP of the server where your Samba drive is located Shared Folder Enter the name of your shared folder Test Click this button to make a connection to the Samba network drive and it will let you know if the settings work Note You can create a simple Samba network drive on your Windows PC by right clicking a folder selecting Sharing and Security and selecting Share this folder Enter a Share name you would like to use for the folder then click the Permissions button and check the box for Full Control Allow for the Everyone group For your camera s Recording settings use Anonymous for the Samba Auth your computer s IP address for the Server and the Share name you chose for the Shared Folder Click on the Test button to test your settings Please note that when creating a simple network drive like this all users on your local network will have access to the contents of this folder D Link DCS 1130 User Manual 24 section 3 Configuration Recording Options Resolution This will let you set which video profile you wish to use to record video Please note that if the bitrate bps of the video profile is higher than your Samba network drive s throughput the recording s framerate FPS may be reduced Record until You can use this setting to adjust how much free space must remain when recording It is suggested that you set this to at least 32M to allow fo
37. rval Enter the time interval the camera will wait before taking a new Snapshot Passive Mode If your FTP server requires you to use passive mode check this box Test Clicking this button will take a snapshot and will try to upload it to your FTP server using the settings you have entered After making any changes click the Save Settings button to save your changes or click the Don t Save Settings button to discard your changes D Link DCS 1130 User Manual C Enable Snapshot Scheduling Event Based Motion Detection Continuous FTP only Scheduled FTP only Send to E mail Address FTP Server Hours Minutes Hours Minutes Sun Start z End Mon Start End Tue Start End Wed Start gt End Thu Start End Fri Start End Sat Start End User Name Password SMTP Mail Server Sender E mail Address Recipient E mail Address Port range 1 to 65535 User Name Password Host Name Path Filename Prefix Port range 1 to 65535 Interval Seconds range 1 to 86400 seconds Passive Mode Don t Save Settings 28 section 3 Configuration Maintenance Maintenance gt Admin Here you can change the Admin password add and manage Users and adjust some camera seitings Admin Password Setting This section lets you change the admin Emmm Sal password used to log in to the camera and adjust settings After installing minadan o E S a eS the camera for the first time it is highly recommended th
38. s the snapshot button to capture the image and save it to your hard drive 5 Can the Internet Camera be used outdoors The Internet Camera is not weatherproof and is not recommended for outdoor use 6 What network cabling is required for the Internet Camera The Internet Camera uses Category 5 UTP Twisted pair cable for 10 Base T and 100 Base T networking D Link DCS 1130 User Manual 36 section 4 Troubleshooting 7 Can the Internet Camera be used as a webcam for my computer No the Internet Camera only functions through an Ethernet or wireless network Other cameras such as the D Link DSB C110 and DSB C310 can be used as a PC Camera webcam 8 Can the Internet Camera be connected to a network if it consists of only private IP Addresses Yes the Internet Camera can be connected to a LAN with private IP Addresses 9 Can the Internet Camera be installed if a firewall exists on the network lf a firewall exists on the network port 80 needs to be opened for data communication You will need to do port forwarding by opening a port to the camera Please refer to your firewall s product manual for detailed instructions 10 Why can t I access the Internet Camera from a web browser A possible cause might be that the IP Address for the Internet Camera is already being used by another device To correct the possible problem you need to first disconnect the Internet Camera from the network Then try to PING follow the instructions in t
39. s will allow you to hear what is happening near your camera Volume This sets the volume level of the incoming audio Note Higher frame size frame rate and bit rates will give you better video quality but they will also require more network bandwidth For best viewing results on a mobile phone we suggest setting the frame rate to 5 fps and bit rate to 20 Kbps After making any changes click the Save Settings button to save your changes or click the Don t Save Settings button to discard your changes D Link DCS 1130 User Manual 21 section 3 Configuration Setup gt Motion Detection This option allows you to set up Motion Detection on your IP camera In order to use motion detection you must first check the Enable Video Motion checkbox You can then click on the video window and draw motion detection zones by clicking and dragging your mouse Red areas mR E indicate areas that will be monitored for motion TTT Sensitivity This setting adjusts how sensitive the camera will be to motion where 100 will be the most sensitive setting and 0 willbe the 90 0 100 least sensitive setting caret Draw motion area O Erase motion area Drawing Mode This will allow you to draw motion detection zones when clicking and dragging or erase motion detection zones when clicking and dragging depending on which option you have selected Clear Clicking this button will clear all motion detectio
40. ter a unique Camera Name for your camera Note Giving your camera a unique name is important when setting up multiple cameras on your network D Link DCS 1130 User Manual Product DCS 1130 azi ikrek can chan pa st ripe deceit for your account as well as add rap elete For seai reie ount s Y n also con e name for your camera and enable its rrp esrb ee aiei eek Coe anhele ae k abria en and recordings of your camera 30 characters maximum 20 users maximum 30 characters maximum Camera Name DCS 1130 36 characters maximum Enable OSD Label DCS 1130 Show time LED light On O Off 39 Appendix A Installing the DCS 1130 on a Router Without UPnP 2 Assign an IP Address and Port for Your Camera e Click on the SETUP tab and select Network Setup A local IP address is required to configure your camera and to view your camera within your local network You may use the default camera IP address of 192 168 0 20 If you wish to use a different IP address be sure that the camera settings correspond to your network settings The Default Gateway will be the IP address of your router s local IP address e g 192 168 0 1 if you are using a D Link router D Link DCS 1130 User Manual SECURITY You can configure your LAN and Internet settings here Save Settings tings Don t Save Settings Save Settings LAN SETTINGS DHCP Connection O Static IP Address IP Address Subnet Mask Default Gateway Primary DNS
41. to be accessed outside your local LAN 14 Why does a series of broad vertical white lines appear through out the image It could be that the CMOS sensor used to record video has become overloaded from exposure to bright lights such as direct exposure to sunlight or halogen lights Reposition the Internet Camera into a more shaded area immediately as prolonged exposure to bright lights will damage the CMOS sensor 15 The video image is blurry how can I correct it You can adjust the Internet Camera focus manually by rotating the focus ring on the front of the camera 16 The video image is noisy has small colored dots How can I solve the problem The video images might be noisy if the Internet Camera is used in a very low light environment 17 The images are low quality or blocky How can improve the image quality Make sure that your computers display properties are set to at least 6 bit color Using 16 or 256 colors on your computer will produce dithering artifacts in the image making the image look as if it is of poor quality You can also adjust image settings in the camera s web interface In the Image Setup section of the web interface you can adjust image related parameters including brightness contrast and saturation Please refer to the Setup gt Image Setup section for detailed information 18 Why are no images available through the Web browser ActiveX might be disabled on your web browser If you are viewing the images fro
42. yed h cam settings SECURITY All of your network connection details are displayed on this page The firmware version is also i ere INFORMATION Camera Name Time amp Date Firmware Version MAC Address IP Address IP Subnet Mask Default Gateway Primary DNS Secondary DNS PPPoE DDNS DCS 1130 Thu Jan 1 12 23 36 1969 1 00 2518 00 01 23 45 67 89 192 168 0 20 255 255 255 0 192 168 0 1 Disable Disable 33 section 3 Configuration Status gt Log The log shows you a list of events that have happened recently You can download the log by clicking the Download button or you can empty the log by clicking the Clear button Helpful Hint CURRENT LOG 1969 12 31 12 01 45 System is booted up 1969 12 31 12 00 38 System is booted up 1969 12 31 12 17 23 System is rebooting 1969 12 31 12 18 13 System is booted up SECURITY D Link DCS 1130 User Manual 34 section 3 Configuration The Help screen provides you with support information about the DCS 1130 for your reference Pa LIVE VIDEO SETUP MAINTENANCE STATUS LIVE VIDEO SETUP MAINTENANCE STATUS Ta LIVE VIDEO me in e e ire e Dynamic DNS Image Setup udio And Video oi etection and Date oe ise 8 Bes Blois le Slt 1B STATUS Device Info Log SECURITY D Link DCS 1130 User Manual 35 section 4 Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur du
43. you choose to reset your settings you will need SECURITY to set up your camera again Reboot Device Clicking the Reboot button will reboot your device D Link DCS 1130 User Manual 31 section 3 Configuration Maintenance gt Firmware Upgrade Your current firmware version and date will be displayed on this page Here you can also upgrade your firmware with a new version Firmware upgrades are made available at support dlink com tw SI gn renee so here To upgrade your firmware go to support dlink com tw and sofas sameness download the latest firmware to your computer s hard drive Click i on Browse select the firmware file then click the Upload button Curent Product name 009 1130 While the firmware is being upgraded do not turn off your computer om or camera and do not disconnect your network connection from your computer or camera Upgrading the firmware will not change any of your system settings but it is recommended that you save your system configuration before doing a firmware upgrade SECURITY Note It is recommended that you use a wired connection for your computer and camera when upgrading the firmware D Link DCS 1130 User Manual 32 section 3 Configuration Status Status gt Device Info This screen shows you various information about your camera and its current settings D Link DCS 1130 User Manual LIVE VIDEO SETUP MAINTENANCE STATUS HELP ice Log This pat n info Logou displa
44. you enter mpeg4 as your RTSP URL setting and your camera s IP is 192 160 0 20 you can view your camera s video with these settings through 192 160 0 20 mpeg4 D Link DCS 1130 User Manual 20 section 3 Configuration Note Video Profile 3 is always set to MJPEG as the Encode Type to ensure that at least one of the Video Profiles are viewable by non lE browsers Video Profile 4 is for mobile devices only and always uses MPEG 4 as the Encode Type sec ss ad vents tas tyr net enone Enable Night Mode Check this box to enable Night Mode Night mode exaust naan allows the camera to use a longer shutter speed when the camera is in NN Mmm low light environment If the camera is in an area where there is sufficient Es Eo a ola ser lighting Night Mode will not affect the video stream eee Encode Type Resolution FPS bps JPEG 640x480 v VIDEO PROFILE 4 FOR MOBILE DEVICE ONLY Shutter This sets the longest shutter speed Night Mode will use when ee Night Mode is enabled and the camera is viewing a low light scene ee CAMERA ENVIRONMENT Enable Night Mode Fi Shutter Second Light Source Indoor Outdoor Light Source Here you can set the kind of lighting used in the area your camera is monitoring to improve the image quality of the video Eble oon Volume Don t Save Settings Enable Microphone Checking this box will enable you to listen to audio picked up by the camera s microphone Thi
45. your snapshots to Port Enter the port used by your SMTP server Test Clicking this button will take a snapshot and will try to upload it to your FTP server using the settings you have entered D Link DCS 1130 User Manual In order to enable your precited take snapshots you must select the checkbox of Enable Sn otification ot Then you can det e the trigger event s and FTP and or email n s Darit Save Set SNAPSHOT C Enable Snapshot Scheduling Event Based Motion Detection Continuous FTP only Scheduled FTP only Hours Minutes Hours Minutes d Sun Mon Tue Wed Thu Fri Sat Send to E mail Address User Name Password SMTP Mail Server Sender E mail Address Recipient E mail Address Port range 1 to 65535 FTP Server User Name Password Host Name Path Filename Prefix 2 section 3 Configuration FTP Server When checked the camera will send the snapshots it takes to the e mail address specified in the text fields If you do not Know what information to enter contact the administrator of the FTP server for details User Name Enter the User Name of your FTP account Password Enter the Password of your FTP account Host Name Enter the Host Name of your FTP account Path Enter the file path to the location on the FTP server you want to send snapshots to Filename Prefix Enter the prefix you want to attach to your snapshot files Port Enter the port used by the FTP server Inte
Download Pdf Manuals
Related Search