DELTA 10 F ZOOM USER MANUAL REL 1.1 ENG
Contents
1. DELTA 10 F ZOOM 03 LDF00 Cc 03 LDF003 al Rel 1 1 GB inazione srl ITALY w dts lig nting it The Lighting Company IP20 ade in Italy 2 DELTA 10 F ZOOM Le informazioni contenute in questo documento sono state attentamente redatte e controllate Tuttavia non assunta alcuna responsabilit per eventuali inesattezze Tutti diritti sono riservati e questo documento non pu essere copiato fotocopiato riprodotto per intero o in parte senza previo consenso scritto della D T S DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche funzionali o di design a ciascun proprio prodotto D T S non assume alcuna responsabilit sull uso o sull applicazione dei prodotti o dei circuiti descritti The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application of the products or circuits described herein Les informations contenues dans le pr sent manuel ont t r dig es et contr l es avec le plus grand soin Nous d clinons toutefois toute responsabil2. 3400ms 20ms 120 149 Pulse open at variable speed from slow to fast 43s 100ms 150 179 Ow Pulse close at variable speed from slow to fast 43s 100ms 180 204 192 Random Strobe Master and RGBA active 205 229 218 Random Strobe Full 230 255 240 Open Parameter DIMMER AN Move DAMA mge range Mode Option Function Value SS 0 255 Proportional dimmer DMX CHANNEL Parameter RED TE Move DAMA mge range Mode Option Function Value Se nna 0 255 Proportionalcolour 26 DELTA 10 F ZOOM DMX CHANNEL ES Parameter GREEN DMX range Mode Option Function Value 0255 Proportional colour DMX CHANNEL Parameter BLUE DMX range Mode Option Function Value 2 0355 Proportional colour DMX CHANNEL econ NN Parameter AMBER DMX range Mode Option Function Value 0235 Proportional colour Parameter ZOOM DMX range Mode Option Function Value 0 255 0355 Linear ZOOM from Narrow to Wide 13 5 40 S Parameter RESET DMX range Mode Option Function Value S No Effect 16 255 Zoom Motors Reset activation after 3 sec NOTE 27 The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T
3. in the path of the projector s movement X 90 WARNING i Do not place any object in the path i of the projector s movement 2 9 DELTA 10 F ZOOM 8 4 Risk of fire Each fixture produces heat and must be installed in a well ventilated place The minimum recommended distance from flammable material is 1 MT A LA Minimum distance from the object being illuminated is 0 5 MT q 0 5M 8 5 Forced ventilation You will note on inspection that the unit features various air inlets and cooling fans located on the head of the fixture These should under no circumstances be blocked or obstructed whilst the projector is in operation Doing so could cause the fixture to seriously overheat thereby compromising its proper operation 8 6 Ambient temperature The projector should never be installed in places that lack a constant air flow The ambient temperature should NOT exceed 40 C 9 MAINS CONNECTION DELTA 10 F ZOOM can operate at 90 260V 50 or 60Hz Prior to connecting the unit to your mains supply ensure that the model in your possession correctly matches the mains supply available For connection purposes ensure that your plug can handle at least 400W power consuption Strict adherence to regulatory norms is strongly Recommended 03 LDF003 T A Comet ge vr rt s FUSE 6A T V MAINS DMX IN OUT Electronic power supply 90 260VAC 50 60Hz 03 LDF003 TWS FUSE 6A T MAINS Electronic power su
4. new DMX channels are DMX channel 13 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 14 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 15 RECORDING channel Records the set scene with a variation between 0 to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed 15 DELTA 10 F ZOOM Slave mode for ChPr program All slave units will be synchronised with master unit running their own Chpr program MENU Up Down oder ENTER Up Down ENTER INFRARED MODE NOTE Infrared remote control External infrared remote sensor By activating Ir MODE it will be needed possible to navigate trought the D T S Code 03 LA 016 unit fun
5. supply consumption Full range AC 90 260V 50 60Hz Power consumption 90V 5 3A 480W 120V 4A 480W 230 V 2 1A 480W 260 V 1 85 A 480 W Thermal Operating ambient temperature 10 40 Weight 18Kg Finishes Black white Certifications and safety CE certification LED class Class 2 LED product Dimensions Packaging Dimensions LxWxH Unit Dimensions LxWxH 630 x 500 x 660 mm 454x205x443mm Weight 20 Kg Weight 18 Kg 454 mm 443 mm 5 ACCESSORIES As standard ei x Omega Clamp with Fast Lock connection 1 4 turn for Delta 10 F cod 02K00523 e User s manual Optional on request e Vireless DMX receiver card cod 03 LA 012 e External 2dBi IP65 Omnidirectional Antenna cod 0508A040 e C Clamp G60 black max load 50Kg cod 0521A004 e C Clamp G60 chrome max load 50Kg cod 0521A004 20 e Safety wire 3mm x 60 cm ring spring catch max capacity load 60Kg cod 0521A010 7 DELTA 10 F ZOOM 6 IMPORTANT SAFETY INFORMATION 6 1 Fire prevention Never locate the fixture on any flammable surface LA Minimum distance from flammable materials 1 m Minimum distance from the closest illuminable surface 0 5 m 0 5M Replace any blown or damaged fuses only with those of identical value Refer to the wiring diagram if there is any doubt Connect the projector to mains power via a thermal magnetic circuit breaker 6 2 Prevention of electric shock A High volta
6. time selectable by user CUPr RGB values selectable by user Rainbow rAIn Rainbow colours effect Speed time selectable by user CU01 CU16 Color Macros as on DMX channel 9 MACRO in Standard Mode 6 SPEE IS SPLE Ss ENTER m S m S m 4 m A Up Down ENTER 9 a E SPELL Down 00108 de di ENTER Up Down ENTER 4 DELTA 10 F ZOOM Pa MENU Up Down ENTER ENTER Up Down ENTER Up Down ENTER AUTOMATIC MODE Automatic demo game without DMX controller WHITE MACROS 16 macros for White color from 2800 to 6500 K DIMMER Dimmer level selectable by user as on DMX channel 2 Dimmer Dimmer level is active for all the programs and macros SHUTTER Shutter level selectable by user as on DMX channel 1 Shutter Shutter level is active only for CU01 CU16 and Wh01 Wh16 Macros ESC Esc from Automatic Mode Menu Is ENTER Less ENTER ENTER Up Down gt gt gt gt ENTER Up Down ees EUS EHS MENU Up Down ENTER ENTER REC MODE In DMX Recorder Mode it is possible to create and store the scenes of the ChPr by using an external DMX controller The unit must be set to 12 channels MODE DMX Recorder Mode For the programming of ChPr by using a DMX controller besides the 12 channels necessary to control the unit a further 3 DMX channels are needed So that in RECORDER mode via DMX the unit will need 15 channels to be correctly programmed The three
7. Down ENTER Up Down position aves REVERSE DISPLAY Suspension IS a m A the mounting position position E On the ground or suspended Up Down IS Stay ENTER Up Down Display OFF Reverses display s reading depending on DISPLAY STAND BY To turn off the display after 5 seconds Or leave it always on E a Display always ON ENTER MENU Up Down ENTER Up Down ENTER DMX MODE To select DMX mode 12 ch default 8 Up Down H L H 8 CHANNELS Is ch AUX CUSTOM and MACRO settings IS ERI AUX MODE IS Not implemented on AUX mode let you activate an external Up Down fT L A ENTER FOS 100 SOLO IS Custom mode enabled ENTER ON OFF control on IR connector Not implemented on DELTA 10 F ZOOM Ys IS IS p Down ENTER Up Down CUSTOM DMX mode let you set the parameters for Shutter Dimmer Red Green Blue Amber White Ctc Macro and Function to the desired DMX L Show Custom settings Setting the parameters ENTER On Custom Mode channels MACRO L Standard mode enabled MACRO Function enable channel Is is Ld I Default no rainbow mapping macro rainbow effects effects on CH9 MACRO STD Standard default Lie EXT Extended C E Is Extended mode enabled Rainbow effects enabled on CH9 MACRO IS IS IS IS MENU Up Down ENTER Up Down LED RGBA Min Max Smooth Compression level values settings and Boost mode Up Down IS RGBA MINIMUM VALUES This menu allow to select the minimum leve
8. EL 7 White WHITE CTC Dmx range value 206 255 0 255 43 color temp Correction Macros 0 2800 K 128 5000 K 255 6500 K IF CHANNEL 7 White NO FUNCTION Dmx range value 0 43 0 255 Smooth RGB linear Hue correction DMX CHANNEL 9 Parameter COLOUR MACROS F IF IS IS AOE IS IS gt Al IS IS St dR PLEASE CHECK PAGE 12 Move DMX range range Mode Option Function Value A 0 14 14 No Function Function ai ii det o 3o Mater 45589 IES E E TEE 6074 Mr 75 89 Y Mares A Mero O tosto Mart O 120134 Mater R 135 149 aero 150 164 Mater IU 165 179 VET 180 194 Maro dt 195 209 Mero O 210 2235 OS ISO IE E ECC 2262239 Y ECC 240255 Macro O 3 DELTA 10 F ZOOM N DMX CHANNEL 9 Parameter COLOUR MACROS F IS IS NNJE F IE SIS EUL HS PLEASE CHECK PAGE 12 pn DMX range Value 0 14 23 30 31 38 39 46 47 54 55 62 63 70 71 78 79 86 95 102 103 110 111 118 119 126 127 134 135 142 143 150 151 158 159 166 167 174 175 182 183 190 191 198 199 206 207 214 215 222 223 230 231 238 239 246 247 255 15 22 87 94 135 142 239246 247 255 _ Parameter FUNCTIONS Recall Create and Store the Custom white DMX range Value 079 80 160 161 255 VO Co DT DT DT DT CT SO O IEA DT DT DT DT DT DT DT DT VO O IEA Macro 15 SO I IEA RI O IEA DT DT DT V
9. ENTER ENTER DELTA 10 F ZOOM ENTER Default OFF Default White 1 Default 255 RESET Zoom motors reset RESET ENABLED VIA DMX RESET DISABLED VIA DMX ZOOM MOTORS RESET Le Ss Down Es m Z 4 m po MENU Up Down ESC te ENTER Ss Down DEFAULT To restore default settings Co TU l C3 IS ES Down IS ES Down Unit temperature TEMPERATURE LS se Down IS ES Down FAN Fan max speed regulation Off fan always off 12 14 16 18 20 22 24 Volt ENTER LIFE TIME This menu show the total UNIT life time and the RGBA life time MENU Up Down ENTER TEST MODE RGBA colours test with rainbow IS IS IS IS IS MENU Up Down ENTER ENTER ENTER UPGRADE This menu let you upgrade the unit firmware JE MENU Up Down ENTER SOFTWARE Software version 17 DELTA 10 F ZOOM 13 AUTOMATIC OPERATION AUTO DELTA 10 F ZOOM can work in automatic mode without a DMX controller First of all connect the projectors with a DMX cable picture below A maximum quantity of 32 slave units can be connected to the same Master unit MASTER SLAVE 1 SLAVE 2 SLAVE 32 DMX OUT DMX IN DMX OUT To activate Auto mode on the first unit use the menu to run through the different modes until AUTO appears on the display and press enter Now it is possible to choose between the different pre programmed games CUPr RAIn CU01 CU16 Wh01 Wh16 or ChPr which is user programmab
10. O O IEA SO O IEA DT DT VO T DT CD DT TE CTD TT Move range Mode Option Function degrees No Function Macro 1 Macro 2 Macro 3 Macro 4 Macro 5 Macro 6 Macro 7 Macro 8 Macro 9 Macro 10 Macro 11 Macro 12 Macro 13 Macro 14 Macro 16 Rainbow Speed 1 1 Sec Rainbow Speed 2 5 Sec Rainbow Speed 3 10 Sec Rainbow Speed 4 20 Sec Rainbow Speed 5 30 Sec ainbow Speed 6 60 Sec ainbow Speed 7 120 Sec ainbow Speed 8 180 Sec andom Speed 1 0 5 sec andom Speed 2 1 Sec Random Speed 3 2 Sec Random Speed 4 5 Sec Random Speed 5 10 Sec Random Speed 6 30 Sec RR Move range Mode Option Function degrees Custom White Recall Enable CH 7 for Custom white Recall Custom White Create Enable CH 7 for Custom white Creation Custom White Store Store the Custom White created 24 DELTA 10 F ZOOM DMX CHANNEL Parameter ZOOM DMX range Mode Option Function Value 0 255 0255 Linear ZOOM from Narrow to Wide 13 5 40 Parameter RESET DMX range Mode Option Function Value S No Effect 16 255 Zoom Motors Reset activation after 3 sec 25 DELTA 10 F ZOOM 8 CHANNELS MODE 1 SHUTTER 2 DIMMER 3 RED 4 GREEN 5 BLUE 6 AMBER 7 ZOOM 8 RESET Parameter SHUTTER DMX range Mode Option Function Value 098 5 poo Black out 10 19 4 Open 2029 24 O Black out 30 119 Strobe at variable speed from slow to fast
11. S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application of the products or circuits described herein MADE IN ITALY CE The Lighting Company ISO 9001 2008 D T S quality system is certified to the ISO 9001 2008 standard D T S products are designed and manufactured at the D T S plants in italy 05171179 D T S Illuminazione s r l Via Fagnano Selve 10 12 14 47843 Misano Adriatico RN Italy Tel 39 0541 611131 Fax 39 0541 611111 info dts lighting it www dts lighting it
12. TA 10 F ZOOM 7 VOLTAGE AND FREQUENCY DELTA 10 F ZOOM can operate at 90 260VAC 50 or 60 Hz 8 INSTALLATION DELTA 10 F ZOOM may be either floor or ceiling mounted For floor mounting installations the unit is supplied with four rubber mounting feet on the base For ceiling mounted installations we reccommend the use of appropriate clamps to fix the unit to the mounting surface The supporting structure from which the unit is hung should be capable of bearing the weight of the unit as should any clamps used to hung it Four 1 4 turn Fast Locks connections placed in the base of the units allow to hang the DELTA 10 R by using the Omega Clamp provided in the box addittional clamps needed for truss installation 8 1 Safety cable AN We recommend the use of a safety cable or chain connected to the DELTA 10 F ZOOM and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail Make sure that the iron cable or chain can bear the weight of the entire unit You may attach the safety chain to the holes located on the base of the fixture 8 2 Protection against liquids The projector contains electric and electronic components which should under no circumstances come into contact with oil water or any other liquid The proper unit functioning would be compromised should this occur 8 3 Movement The projector has a maximum movement of 90 for Tilt DO NOT place any obstructions
13. Y CONDITIONS The unit is guaranteed for 36 months from the date of purchase against manufacturing material defects 5 DELTA 10 F ZOOM 4 TECHNICAL FEATURES DELTA 10 F ZOOM RGBW is a new LED colour changer featuring a motorized zoom 13 5 40 ideal for rental applications that demand intense and nearly continuous usage DELTA 10 F ZOOM RGBW is the brightest LED colour changer in its category 6 200 Lux at 5 m 13 59 In fact its light source is composed of 240 LEDs 60 x Red 60 x Green 60 x Blue 60 x White with 19 500 total lumens The LEDs even distribution pattern featuring the same quantity of red green blue and white LEDs guarantees high mixing quality for RGBW colours and a uniform projection on surfaces no matter what colour is used DELTA 10 F ZOOM RGBW can generate 16 million colours colour temperature can be varied over a linear range from 2800 K to 6500 K DELTA 10 F ZOOM RGBW offers an IP20 protection rating DELTA 10 F ZOOM RGBW has a full range AC 90 260 V 50 60 Hz power supply and therefore ensures reliable operation even in the case of voltage drops DELTA 10 F ZOOM RGBW can be used without external consoles in chains of colour changers including up to 32 units All functions of the internal DELTA 10 F ZOOM RGBW menu can be programmed and memorized in a sequence of events including different luminosity settings generation of 16 million different colours special effects etc which can be played back in a pre
14. al connected the Antenna transmitter will flash red green display blinking on Delta 10 F To log Delta 10 F off from a transmitter simply select UNLINK function under WIRELESS DMX MENU IO 1 111 and press ENTER When Delta 10 F is logged off the display is blinking meaning its available for log in on a new transmitter Logging out a Delta 10 F 417 oy Ud AH Select UNLINK function LMA 11 under WIRELESS DMX MENU and press ENTER When Delta 10 F is logged off the display is blinking meaning its available for log in on a new transmitter Logging out all Delta 10 F linked to a transmitter Press and hold the function button of the transmitter for about 3 seconds When the display is blinking on Delta 10 F it mean that the units are logged out Transmitter Status LED Flashing red green no dmx connected Solid green dmx signal detected and transmitted Fast flashing red green log in mode every free Delta 10 F unit not logged in to any other transmitter will be logged on Delta 10 F Status Display blinking not logged on to a transmitter free Solid display logged on to a transmitter and receiving dmx data 16 nc MENU Up Down II C1 ENTER Up Down EMERGENCY Emergency operating mode By setting Emergency mode it will be possible to select one of the 16 preprogrammed WHITE cues that will then ran if DMX signal is missing or not available Usefull for Emergency EXIT ilumination on public areas gt gt ENTER
15. connector with a 120 ohm resistor Between pin 2 and 3 The DMX terminator must be plugged into the last unit DMX out panel connector of the DMX line PLACE A 120 OHM RESISTOR BETWEEN PIN 2 AND 3 OF A MALE XRL CONNECTOR AND PLUG IT INTO THE DMX OUT PANEL CONNECTOR OF THE LAST UNIT CONNECTED TO THE DMX LINE PIN 3 PIN 2 11 DELTA 10 F ZOOM 10 1 DMX Addresses DELTA 10 F ZOOM can be used in 3 different DMX modes 12 DMX control channels 8 DMX control channels or CUSTOM mode channels Here below is described the DMX channels addressing for the controller when DELTA 10 F ZOOM is set to 12 DMX control channels Projector 1 A001 Projector 2 A013 If you want to select the next projector just add 12 Projector 3 A025 Lera A projector 6 A061 10 2 Selelcting the DMX address 1 Press the UP DOWN key until you reach the required DMX address The numbers on the display will start to flash but the new DMX address hasn t yet been set 2 Press ENTER to confirm your selection The numbers on the display will stop flashing and the projector is now controlled by the new DMX address TIPS if you keep pushed the UP or DOWN keys the channels are calculated more quickly and you get a faster selection 11 FIRMWARE UPDATING Warning This procedure require a base knolewge of computer applications and Windows Hyperterminal program Please refer to an authorised D T S service centre To update the soft
16. ctions by using the D T S infrared remote control D T S Code 0514L008 Not implemented on DELTA 10 F TH we ZOOM bole WIRELESS DMX SYSTEM IS ES Lien ENTER Up Down ES La IS ENABLED WIRELESS DMX SYSTEM WIRELESS DMX DISABLED Wieless DMX enabled disabled By activating WDMX MODE it will NOTE be possible to control DELTA 10 F Wireless DMX receiver card ZOOM via D T S ANTENNA needed cod 03 LA 012 Wireless DMX Transmitter cod External IP65 2dbi 03 E1271 omnidirectional Antenna WIRELESS DMX system on IS UNLINK LOG OUT needed cod 0508A040 DELTA 10 F ZOOM is available ENTER on request Logging on Delta 10 F WIRELESS DMX must be enabled on Delta 10 F unit S SELES S Ga To log on the Delta 10 F in the WIRELESS system simply press and quickly release the function button on the transmitter The transmitter will start flashing rapidly red green scanning for new free receivers Delta 10 F units When a Delta 10 F logs on to the transmitter the LINK green light on transmitter starts to flash rapidly After approximately 10 seconds the transmitter will jump back to normal mode and continue transmitting data The Delta 10 F now try to synchronize to the transmitter When synchronized to the transmitter 2 different modes are possible 1 Antenna transmitter has detected and transmits a DMX signal in this mode a solid green light is seen on the transmitter and solid display is seen on Delta 10 F 2 No DMX sign
17. determined sequence over an entire week The DELTA 10 F ZOOM RGBW can operate in vertical horizontal or inverted positions and can be positioned on the floor or ground or fitted to trusses it is complete with a practical accessory DELTA 10 F ZOOM is also available as DELTA 10 F CT ZOOM 240 LEDs 180 x White 60 x Amber On demand the unit is also available in RGBA version DELTA 10 F ZOOM RGBW Cod 03 LDF003 T e Electronic Power Supply 90 260VAC 50 60 Hz Motorized Zoom e Grey glitter finish Cod 03 LDF003 TWS e Electronic Power Supply 90 260VAC 50 60 Hz Motorized Zoom Wireless DMX ready external Antenna needed e Grey glitter finish LED technology 240 LEDs 60 x Red 60 x Green 60 x Blue 60 x White LEDs average lifespan 100 000 hours Total luminous flux 19 500 Lumens 6 200 Lux at 5 m 13 5 RGBW colour generation 16 million colours Colour temperature variable on a linear range 2 800 K 6 500 K no infrared no ultraviolet emissions Optical units Motorized Zoom 13 5 40 User interface 4 eight digit LED display with 4 buttons Independent operation Fully programmable via built in user interface Master or Slave capability chains of up to 32 interconnected units Control Remotely controlled by cable or wireless on request USITT DMX 512 serial digital protocol reception transmission DMX channels 12 Protection IP20 protection level 6 DELTA 10 F ZOOM 4 TECHNICAL FEATURES Power
18. ge is present inside the unit Isolate the projector from the mains supply prior to performing any function which involves touching the inside of the unit The level of technology inherent in the DELTA 10 F ZOOM requires the assistance of specialised personnel for all servicing Please refer to an authorised D T S service centre A good earth connection is essential for proper functioning of the projector Never connect the unit without proper earth connection The fixture should be located in places with a good air ventilation 6 3 Protection against direct light radiation Never turn the unit on if any of the lenses or the glass lenses protection is damaged Never look directly the leds when they are on 6 4 Safety AN The projector should always be installed with bolts clamps and other tools that are capable of supporting the weight of the unit Always use a second safety chain to sustain the weight of the unit in case of the failure of the main fixing point The external surface of the unit at various points may exceed 80 C Never handle the unit until it s on Never install the fixture in an enclosed area lacking sufficient air flow The ambient temperature should not exceed 40 C A 6 5 Level of protection against the penetration of solid and liquid matter The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid matter is IP20 8 DEL
19. iquid matter 7 VOLTAGE AND FREQUENCY 8 INSTALLATION 8 1 Safety cable 8 2 Protection against liquid 8 3 Movement 8 4 Risk of fire 8 5 Forced ventilation 8 6 Ambient temperature 9 MAINS CONNECTION 9 1 Protection 10 DMX SIGNAL CONNECTION 10 1 DMX Addresses 10 2 Selecting the DMX address 11 FIRMWARE UPDATING 12 DISPLAY FUNCTIONS 13 AUTOMATIC OPERATION 13 1 CUPr RAIn CU01 CU16 Wh01 Wh16 13 2 ChPr MASTER SLAVE 13 3 Rec mode 14 PERIODIC CLEANING 15 PERIODIC CONTROLS 16 DMX PROTOCOL 8 8 10 11 17 19 20 4 DELTA 10 F ZOOM 1 SYMBOLS Graphic symbols used on this manual THIS SYMBOL INDICATES A HOT SURFACE THIS SYMBOL INDICATES ELECTRIC SHOCK RISK THIS SYMBOL INDICATES GENERAL RISK THIS SYMBOL MEANS DO NOT PLACE THE UNIT ON INFLAMMABLE SURFACES THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO 1 M BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT 2 GENERAL WARNING Read the instruction contained in this user manual carefully as they give important information regarding safety during installation use and maintenance The device is not for domestic use and must be installed by a qualified electrician or experienced person Always disconnect the device from the mains before replacing the lamp The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating The device must always be equipped with an efficient ground connection 3 GENERAL WARRANT
20. it en cas d ventuelles inexactitudes Tous droits r serv s Ce document ne peut tre copie photocopi ou reproduit dans sa totalit ou partiellement sans le consentement pr alable de D T S D T S se r serve le droit d apporter toutes modifications et am liorations esth tiques fonctionnelles ou de design sans pr avis a chacun de ses produits D T S d cline toute responsabilit sur l utilisation ou sur l application des produits ou des circuits decrits Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y controladas Con todo no se asume ninguna responsabilidad por eventuales inexactitudes Todos los derechos han sido reservados y este documento no puede ser copiado fotocopiado o reproducido total o parcialmente sin previa autorizaci nescrita de D T S D T S se reserva el derecho a aportar sin previo aviso cambios y modificaciones de car cter est tico funcional o de dise o a cada producto suyo D T S no se asume responsabilidad de ning n tipo sobre la utilizaci n o sobre la aplicaci n de los productos o de los circuitos descritos INDEX 1 SYMBOLS 2 GENERAL WARNING 3 GENERAL WARRANTY CONDITION 4 TECHNICAL FEATURES 5 ACCESSORIES 6 IMPORTANT SAFETY INFORMATION 6 1 Fire prevention 6 2 Prevention of electric shock 6 3 Protection against direct light radiation 6 4 Safety DELTA 10 F ZOOM WN IW US 6 5 Level of protection against the penetration of solid and l
21. le through REC mode To confirm game activation press ENTER on the selected GAME 13 1 CUPr RAIn CU01 CU16 Wh01 Wh16 The first unit that will work as a Master should be placed in Automatic mode AUTO the other units have to be placed in 12 channels DMX mode MODE 12CH and the DMX address should be set at A001 For Raln rainbow game it is possible to select the speed for the colour changhing SPEE DIMMER function in AUTOMATIC MODE is active for all the programs SHUTTER function in AUTOMATIC MODE is active only for CU01 CU16 and Wh01 Wh16 macros 13 2 ChPr MASTER SLAVE The first unit that will function as a Master must be set to Automatic mode AUTO the other units must be set to Slave mode SLAV selectable through the menu In this way all the Slave units will be synchronised with the master and running their own ChPr game On the master unit it is possible to vary the Speed time SPEE for the colour changhing and the Wait time UAIt between the steps Speed time and Wait time on the Master have priority on the slave units NB It is possible to run GA Pr on the other units even though these do not have GA Pr programmed You can do this by setting the units to 10 channels DMX mode MODE 10CH and selecting DMX address A001 18 DELTA 10 F ZOOM 13 3 Rec mode It is possible to program your own game on DELTA 10 F ZOOM that will then run it in AUTO mode ChPr Each unit can have its own programmed game In REC mode the u
22. ls for Red Green Blue and Amber Up Down IS RGBA MAXIMUM VALUES This menu allow to select the maximum levels for Red Green Blue and Amber These settings have priority on Master Dimmer DMX channel 2 SMOOTH VALUE This menu allow to select the value of the delay in millisecons for RGBA and Dimmer channels reaction to DMX or Program variation Off 25 ms delay Fast response 20 250 ms delay Slow response Up Down COMPRESSION This menu allow to select between Linear current output or Quadratic current output for LEDS Default Linear SYNC This menu allow to adjust the PWM frequency value Hz in order to reduce flickering in the process of your camera recordings Up Down Up Down BOOST DRIVING This menu allow to increase the LED s current from 350mA to 500 mA Up Down Orie mii 13 DELTA 10 F ZOOM ES ES ENTES ENTER ENTER Up Down ENTER ENTER ENTER Up Down ENTER Default 100 IS ENTER ENTER Up Down ENTER Default 100 IS ENTER LJ Range Off 20 ES UN Down l Default 4 ENTER Linear Linear ES ES Down current output ENTER Quadratic Linear light ENTER output Range 610 Hz 10 KHz ES UN Down Default 610 Hz ENTER With BOOST active the LED s ES is Down current is set to 500mA 30 more gain Default Disable Up Down AUTOMATIC gt PUED Automatic demo game without DMX controller ChPr Chase with 16 steps previously created in REC MODE Speed and Wait
23. luminous output substantially Regularly clean the front lenses glass using a soft cotton cloth dampened with a specialist glasses cleaning solution 15 PERIODIC CONTROLS Mechanical parts Periodically check all mechanical parts and the gaskets replacing them if necessary Electrical components Check all electrical components for correct earthing and proper attachment of all connectors refastening if necessary Fuse replacement A Locate the fuse which protect the electronics in the base of the DELTA 10 F ZOOM Using a multimeter test the condition of the fuse replacing it with one of equivalent type if necessary Attention Disconnect mains power prior to removing the projector housing A 20 DELTA 10 F ZOOM 16 DMX PROTOCOL 12 CHANNELS MODE Default 1 SHUTTER 2 DIMMER 3 RED 4 GREEN 5 BLUE 6 AMBER 7 WHITE Pre programmed whites at different colour temperatures 8 CTC 9 COLOURS MACRO 10 FUNCTIONS 11 ZOOM 12 RESET Parameter SHUTTER DMX range Mode Option Function Value a 5 poo Black out 10 19 14 Open 2029 24 Black out 30 119 Strobe at variable speed from slow to fast 3400ms 20ms 120 149 Pulse open at variable speed from slow to fast 43s 100ms 150 179 Lg Pulse close at variable speed from slow to fast 43s 100ms 180 204 192 Random Strobe Master and RGBA active 205 229 218 Random Strobe Full 230 255 240 Open Parameter DIMMER CA Mo
24. nit must be set to 12 channels mode To program the ChPr by using a DMX controller you need 3 more channels in addition to the 12 channels necessary to control the unit So that in RECORDER mode via DMX the unit will need 15 DMX channels to be correctly programmed The three new DMX channels are DMX channel 13 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 14 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 15 RECORDING channel Records the set scene with a variation between 0 to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed 19 DELTA 10 F ZOOM 14 PERIODIC CLEANING Front lenses Glass The dust can reduce the
25. pply 90 260VAC 50 60Hz DMX IN OUT Panel connector for Metal support for external WIRELESS DMX Antenna external WIRELESS DMX Antenna 9 1 Protection The use of a thermal magnetic circuit breaker is recommended for each DELTA 10 F ZOOM A good earth connection is essential for the correct operation of the projector 10 DELTA 10 F ZOOM 10 DMX SIGNAL CONNECTION The unit operates using the digital DMX 512 1990 signal Connection between the mixer and the projector or between projectors must be carried out using a two pair screened g 0 5 mm cable and a XLR 5 or 3 pins connector Ensure that the conductors do not touch each other Do not connect the cable ground to the XLR chassy The plug housing must be isolated Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one This way all the projectors are cascade connected NB If the display showing the DMX address flashes then one of the following errors has occurred DMX signal not present DMX address not valid DMX reception problem CONTROLLER STANDARD DMX 512 I N a 1 GND 2 DATA 4 ES 2 3 DATA 3 I DMX OUT DMX IN DMX OUT DMX IN DMX OUT DMX IN i DMX OUT S2 For Installations where long distance DMX cable connections are needed we suggest to use a DMX terminator The DMX terminator is a male XLR 3 5 pins
26. ve DAMA renge range Mode Option Function Value E ENEE 0 255 Proportional dimmer _ DMX CHANNEL Parameter RED AE Move DAMA range range Mode Option Function Value AA grees 0 255 Proportionalcolour 21 DELTA 10 F ZOOM DMX CHANNEL ES Parameter GREEN NS Move DID renge range Mode Option Function Value 0 255 Proportionalcolour DMX CHANNEL Parameter BLUE as Move DMX range range Mode Option Function Value A eee 0255 Proportionalcolour DMX CHANNEL nasa JE Parameter AMBER Move AMIR range Mode Option Function Value O ang 0 255 Proportionalcolour Parameter WHITE Pre programmed White at diff color temperature DMX range Mode Option Function Value o 055 No Function 56 105 4 Full Red Green Blue at Full 106 155 130 White DTS IF CHANNEL 10 FUNCTIONS CUSTOM WHITE RECALL Dmx range value 0 79 156 205 180 Custom White Recall White CTC Channel 8 CTC enabled 2000295 ane 43 color temp Correction Macros 2800 K 6500 K IF CHANNEL 10 FUNCTIONS CUSTOM WHITE CREATE Dmx range value 80 160 156 205 Custom White Create RGB levels selectable by DMX 206 255 White CTC Channel 8 CTC enabled 43 color temp Correction Macros 2800 K 6500 K 22 DELTA 10 F ZOOM _DMX CHANNEL 8 Parameter CTC Color temperature correction Move LAS minge range Mode Option Function Value degrees IF CHANN
27. ware version of the DELTA 10 F ZOOM you need D T S RED BOX interface D T S Code 03 LA 008 USB DMX Driver for the D T S RED BOX interface D T S Firmware upgrade utility program The driver and the installation procedure are available in our web site www dts lighting it Updating the software version Please follow the procedure below to perform the update 1 Install the D T S RED BOX USB DMX driver on the PC you will use to update the unit software 2 Connect the D T S RED BOX interface to the PC by using a USB cable 3 Connect the D T S RED BOX interface to the fixture by using a DMX cable 4 Download the new software version into the unit by using D T S Firmware upgrade utility program It will be possible to download the software from the reserved area of D T S web site www dts lighting it 12 DELTA 10 F ZOOM 12 DISPLAY FUNCTIONS DOW UP DISPLAY FUNCTIONS The DELTA 10 F ZOOM display panel shows all the available functions Using these functions it is possible to change some of the parameters and add some functions Changing the D T S setting can vary the functions of the unit so that it does not respond to the DMX 512 signal used to control it Carefully follow the instructions below before carrying out any variations or selections NOTE the symbol I shows which key has to be pushed to obtain the desired function Software version 2 17 IS IS IS IS IS IS Fio IS MENU Up Down ENTER Up
Download Pdf Manuals
Related Search