E1 SFP Programming Module User Manual MS100079
Contents
1. and NMS Ethernet Interface Compliant with 802 3 802 3u standards 100 Base TX with RJ45 connector Full duplex Support Auto negotiation oaonvco LED indicator for Ethernet Link status and activity 3 Power Supply a 5 VDC Power Jack b Maximum Power Consumption lt 5 watts 4 Operating Environment a Ambient temperature 0 40 C for indoor application b Storage temperature 0 85 C c Relative humidity 5 95 non condensing 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com E1 SFP Programming Module User Manual Page 4 of 10 Front Panel 1 System Indicators PWR Power on off LED ALM System failures errors 2 Reset Button Use this button to restart the system 3 LAN Ethernet Interface The LAN interface is a RJ45 connector with two LED indicators Two LED indicators are described below ORANGE LED Solid orange indicates Ethernet link is up GREEN LED Blinking green indicates Tx Rx traffic is traversing the port 4 NMS Ethernet Interface The NMS interface is a RJ45 connector with two LED indicators Two LED indicators are described below GREEN LED Solid green indicates Ethernet link is up ORANGE LED Blinking orange indicates Tx Rx traffic is traversing the port 5 CONSOLE port A RS232 interface with baud rate 115200bps via DB9 female to DB9 male cable is provided for diagnostic The user commands CLI command are listed in Table 1 6 5VDC Powe2. bit 1 Flow control none Login password microsens The CLI commands are summarized as follows Table 1 CLI Command Description CLI Command Description version Display software version and related information cdisp Display current configurations of the programming box ipset ip_addr net_mask Set NMS port IP address subnet mask and gateway address gw_addr ip_addr NMS port IP address to be assigned net_mask subnet mask of IP address gw_addr gateway IP address Example ipset 192 168 1 11 255 255 255 0 192 168 1 254 ipget Display NMS port current IP address upgrade tftp_server_ip Upgrade software image from TFTP server file_name tftp_server_ip TFTP server IP address file_name the file name of software image to be upgraded EX upgrade 192 168 1 12 file_to_be_upgraded bin ping ip_addr Use ICMP to check connection EX ping 192 168 1 11 csave Save current configurations to FLASH logout Logout CLI System 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com E1 SFP Programming Module User Manual Page 10 of 10 Disclaimer All information in this document is provided as is and subject to change without notice MICROSENS GmbH amp Co KG disclaims any liability for the correctness completeness or quality of the information provided fitness for a particular purpose or consecutive damage Any product names mention
3. page Configuration gt SFP Configuration MICROSENS Log Out General Configuration Version Information Version Information Project Name E1 SFP Programming Module Hardware Version 1 00 Software Version 2 O5br Firmware Version MS100079_250510 bintag Build Time 2014 9 23 10 30 STEP V Move the mouse pointer over the Configuration name and click the SFP Configuration name again The programming web page will read back just saved parameters and display them on the screen Please check if they are correct or not If not please repeat the above steps MICROSENS General Configuration SFP Configuration Monitor Debug SFP zul Duden ne A O TX PWID Unframed E1 OFramed E1 Current Framed Mode Unframed E1 CRC Enable CRC Enable Current CRC Status CRC Disable Time Slot Number 32 Current Time Slot Number 32 Time Slots Active PCMSO ieee Current Time Slot FFFF Time Slot En Current WAN Packet 782 Bytes Current Jitter BD 11 ms Current E1 TxCLK Adaptive Apply New Setting 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com E1 SFP Programming Module User Manual Page 9 of 10 Command Line Interface for Setup Hyper terminal as Local Craft Terminal When logging into the Hyper terminal set up the craft port as follows Bit rate 115200bps Data bit 8 Parity none Stop
4. 0 Software Version 2 05br Firmware Version MS100079_250510 bin tag Build Time 2014 9 23 10 30 STEP III Configuration gt E1 SFP Configuration Move the mouse pointer over the Configuration name and click the SFP Configuration name The programming web page will get the current settings from the E1 SFP and display them on the screen Once you ve finished making changes you need to commit them by clicking Apply New Setting button MICROSENS Log Out General Configuration SFP Configuration Monitor Debug SFP Configuration Source NMAC in a aa se Destination NMAC 00 so r foo foo or Source IP ADDR h2 fies ft ft Destination IP Addr ma tes ff f2 TX PWID PR PWID Framed Unframed E1 OFramed E1 Current Framed Mode Unframed E1 CRC Enable CRC Enable Current CRC Status CRC Disable Time Slot Number 32 _ Current Time Slot Number 32 Time Slots Active PCM30 DIPCM31 2 ul sf ef elo Current Time Slot FFFF Current Time Slot FFFF Current WAN Packet 782 Bytes Current Jitter BD 11 ms Current E1 TxCLK Adaptive Apply New Setting 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com E1 SFP Programming Module User Manual Page 8 of 10 STEP IV After saving new settings to the E1 SFP the programming web page will go back to Home
5. MICROSENS E1 SFP Programming Module User Manual MS100079 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com E1 SFP Programming Module User Manual Page 2 of 10 Caution Circuit electrical equipment is sensitive to the impact of static electricity which can endanger their delicate electronics Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge To protect your equipment please pay attention to the following Touch the metal chassis of your computer to ground the static electrical charge before you pick up the circuit equipment Pick up the device by holding it on the left and right edges only Put on the strap of static electricity proof to avoid impacting the function during the equipment is operating Functional Description The E1 SFP programming module is designed for an engineer to configure and check E1 SFPs parameters via a webpage before they can be installed in the real network for E1 service It contains 2x Ethernet ports 1x sub D9 console port and 1x 5VDC power jack for connecting to an external power adaptor It is intended for use with E1 SFP MS100070 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com E1 SFP Programming Module User Manual Page 3 of 10 Technical Specifications 1 Physical Dimension Height 29 mm Width 158 mm Depth 114 mm Weight 0 5 kg 2 LAN
6. ed herein may be trademarks and or registered trademarks of their respective companies 2014 MICROSENS GmbH amp Co KG Kueferstr 16 59067 Hamm Germany All rights reserved This document in whole or in part may not be duplicated reproduced stored or retransmitted without prior written permission of MICROSENS GmbH amp Co KG Sh av MS100079_MAN_EN_V1 0 1 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com
7. r Jack Inner diameter 2 0 mm Outer diameter 5 6 mm Center Voltage Polarity Positive 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com E1 SFP Programming Module User Manual Page 5 of 10 E1 SFP Configuration I Configuration Architecture Media Converter or Switch Programming Box 100Base FX PC 192 168 1 12 II PC IP configuration Before configuring E1 SFPs please set your PC IP address as follows IP Address 192 168 1 12 Subnet Mask 255 255 255 0 Gateway 192 168 1 11 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com E1 SFP Programming Module User Manual Page 6 of 10 III E1 SFP Configuration STEP I Invoke the web browser and enter the following URL http 192 168 1 11 6868 MICROSENS Log Out General Configuration Please Log In STEP II Key in the user name amp password User name admin Password microsens MICROSENS Log Out General Configuration Please Log In jadmin 2014_MICROSENS GmbH amp Co KG_K ferstr 16_59067 Hamm Germany_www microsens com E1 SFP Programming Module User Manual Page 7 of 10 After clicking on the Log In button the Version Information screen will be displayed MICROSENS General Configuration Version Information Log Out Version Information Project Name E1 SFP Programming Module Hardware Version 1 0
Download Pdf Manuals
Related Search