User Manual Program GMG – VD 1.0 - gte
Contents
1. is occupied by the mouse which means that you have the choice of Com 2 Com 3 or Com 4 Not existing interfaces are displayed covered up The suppliers adjustment is Com 1 because normally the program is installed on a Laptop which has an integrated mouse Choice of interface C Coma C Eons Coni A new connection may be tested by command Connection test in the GMG menue A faulty or noe connection is displayed in another windows below the tool box as status display no connection 6 Start information Data may be transferred from GMG via menu GMG and data transfer or from hard disk via file and data transfer One set of data consists of all data of the instrument i e alll measurements and the appropriate travels scans Via the menu file and measurement transfer the measurements and the scans can be transferred The file names for a set of data are dat and for a single measurement mes The same names are also valid for the saving of data 7 First measurement Bring the GMG to the measuring place and switch it on Now perform the desired number of measurements or scans According to the standard 5 travels scans must be carried out for each measurement After 2 test scans 3 further scans must be carried out From these last 3 scans the average value of the sliding friction coefficient is determined which is then saved together with the2. 7 GMG VD Seite 2 GTE Abt Ind SW 1 The GMG Program The program GMG VD 1 0 allows to visualize and to record measurements of sliding friction Together with a Laptop and the GMG 100 SC instrument the sliding friction of floor surfaces may be tested at any place The measured data ofthe GMG 100 SC can be transferred to and saved on a data medium Saved measurements can be visualized at any time The program furthermore allows to establish a record of the measurements with can be saved and printed The program also shows the data transferred from the GMG 100 SC instrument as an instructive diagram Standard display The data of the GMG 100 SC their calculation and evaluation and the measuring curves used for the calculation of the final result are visualized The part of the measuring curves used by the instrument to form the average value are also visualized and dispolayed Since the instrument GMG 100 SC is in total retractably calibrated and the program in this mode is only used to visualize and to record the calculated data the indicated values are equally retracably calibrated Special mode For testing purposes the program offers the possibility to choose that part of the measuring curves used for and calculation of average values This special mode does not influence the standard values in the instrument but offers further possibilities of processsing measured values by visualization 2 System requirements 486 33M
3. measuring diagram The measuring diagram and the computed values remain saved also when the instrument is switched off The GMG can save totally 90 scans e g 18 measurements with 5 scans each GMG VD Seite 4 8 Data transfer from GMG instrument Connect the GMG via the special cable to the serial interface of the PC of Laptop Switch it on Start the GMG program and click on function GMG and data transfer Now the data are transfered If not the following instructions are displayed on your monitor During data transfer a fault has occured Please check the following points e The GMG instrument is not switched on e Wrong interface chosen e Connection GMG to PC faulty or not existing GTE Abt Ind SW For further information click on Help i amp Choice of measurement After transfer of data from hard disc or GMG the following windows is desplayed on the monitor GMG choice of measurements Please choose the measurement to be treated Measurement 1 30 Saved measurements Scans per measurement This example shows only 1 measurement with 5 scans GMG evaluation Measurement 2 Sliding friction coefficient Measuring range cm SE SE SR ee t tot GMG VD Seite 5 GTE Abt Ind SW Now the diagrams to be displayed may be chosen The column Average value GMG shows the sliding friction values measured by the GMG On each diagram that range of th complete curve is di
4. GTE Abt Ind SW Gesellschaft f r phys Technologie u Elektronik mbH Gr Entwicklung elektronischer Syteme Industrielle Steuerungstechnik i stechni Sicherheit k Umweltanalytik RE Sensoren und Aktoren Remanufacture Centre mm Dum ne Automotive Electronics SSS Saeed User Manual Program GMG VD 1 0 for evaluation and recording of sliding friction measurments GMG Analysis Sliding Friction Coefficient p ra L a m 1999 by GTE GTE Ind Elektronik Helmholtz Str 38 40 D 41747 VIERSEN Tel 49 02162 3703 0 Fax 49 0 2162 3703 25 May 1999 GTE Elektronik GMG VD Seite 1 GTE Abt Ind SW Contents I The GMG Program eee ea che etn ae a TOR che ee eS 3 2 System requirements eiie l nge nennen RRSS BUN IIND ERDE De ge eR US 3 3 Installation ce REO AR EROR TEE RR Rv ck eee RE NETUS 3 A Start of prostan pinna ERO Wa te eA RB Reda 3 X Eirstst rt M taste 4 6 Start information ze oco A pete E late kA a E R A 4 7 First measurement eee eie ls it e e iode ecd 4 8 Data transfer from GMG Instrument sees eene nnn 5 9 Choice of language onec bo las Eee EUR Haul RE NE ROPA S 6 10 State of delivery of GMG Program and GMG 100 SC instruments eee 7 11 Read data from data medium cse etii ie tede e es 7 12 Prmtng 54 tendo demam deas n Be aie dele en e
5. T THE COMPANY GTE IS IN NO WAY RESPONSIBLE FOR ANY INDIRECT OR CONSEQUENTIAL OR ANY SIMILAR DAMAGE INCLUDING DAMAGE CAUSING GAIN OR LOSS OF DATA CAUSED BY INCORRECT USAGE OF THE SOFTWARE OR INCAPABLITY WHILST USING THE SOFTWARE EVEN IF GTE IS INFORMED OF THIS POSSIBILITY SOME STATES DO NOT ALLOW THE LIMITED OR COMPLETE EXCLUSION OF THE RESPONSIBLITY FOR ACCOMANYING OR CONSEQUENTIAL DAMAGE SO THAT THE ABOVE MENTIONED RESTRICTIONS OR COMPLETE EXCLUSIONS MAY NOT AFFECT YOU IN ANY CASE THE GTE LIABILITY IS LIMITED TO THE SELLING PRICE OF THE SOFTWARE The above exclusions and limitations are independent of your acceptance of the software GMG VD Seite 7
6. contained in it The software obtained with this license following identified as software is the property of the Company GTE or their license producer and is protected through national aws and international contracts With acceptance of the license conditions you receive the right to use the software As long as no other additional agreements are delivered with this license the following conditions apply for the use of the software You are entitled a to use a copy of the software on an individual computer b to make a copy of the software for archive use or to copy the software onto the hard disc of your computer and keep the original disc for archive purposes You are not entitled a to copy the documentation delivered with the disc b to lend lease or pass on part or all of the software or issue secondary licenses c to reverse engineer decompile or disassemble the software or try to use any other methods to render accessible the original coding to change the software or to translate or produce products derived therefrom d after receiving an exchange disc or an upgrade version as a replacement for an earlier version received previously or the earlier version itself to use the earlier software version In all other cases all earlier versions of the software must be destroyed after receipt of an updated version INDEPENDENT OF THE FACT THAT IF ONE OF THE LAWFUL CONDITIONS LAID DOWN HEREIN EVEN THE ESSENTIAL AIMS ARE NOT ME
7. hz or higher 8 16 MB main memory serial interfaces and mouse 3 A drive 5 MB free space on hard disc graphic card with 800 x 600 Windows 95 98 3 Installation Your PC or Laptop must be equipped with Windows 95 98 Put diskette 1 of GMG installation diskettes into your drive and start the setup program from the Explorer of Windows 95 by double click on setup exe Follow the instructions of the setup program It will aks for the directory into which the GMG program should be installed The proposal to use the standard directory should be altered only for compelling reasons Futher adjustments are now made automatically You will only be asked to put the next installation diskette into the drive and to acknowledge 4 Start of program The setup program automatically installs an individual program group for the GMG program In Windows 95 you can find the program via start menue left below in the task bar Move the cursor to Programs In the menue displayed you will find GMG VD 1 0 program from where the program can be started or you may use the icon on the desktop produced by the setup program 5 First start First check the connection between GMG 100 SC instrument and your PC or Laptop If necessary the com parts must be changed in menue Adjustments and sub menue Interfaces GMG VD Seite 3 GTE Abt Ind SW The window shows the number of interfaces in your PC On most PC s the interface Com 1
8. nction Treatment and Record a recording window is opened into which all relevant data may be inserted These insertions are printed out together with the measuring diagrams With the function Remarks additional remarks may be inserted 9 Choice of Language not yet installed At option 2 languages are incorporated in the program German and English Choice can be made via menu Adjustments The language may be changed during working 10 Delivery status of GMG program and GMG 100 SC instruments The GMG program is only compatible with the supplied GMG 100 SC instruments During data transfer the program compares the lincensed internal numbers of the GMG instruments If a GMG instrument which is not licensed for the relevant program is connected to the GMG program an error message will be displayed instrument not licensed for this program GMG VD Seite 6 GTE Abt Ind SW If at a later date further GMG instruments are supplied and should be operated with the initial program a new update diskette will also be supplied which contains the license numbers of these additional instruments 11 Read data from data medium All saved data may be read directly from the hard disc or the diskette 12 Printing Under this function a record with diagram is printed The optimum print qulity especially of the diagram is obtained by using a laser printer If an inkjet or wire printer is used the print quality ma
9. splayed which was automatically chosen to determine the average value and during which the reuired speed accuracy was maintained By clicking on the button Treatment you change from the disply mode to the treatment mode Now you have the possibility to choose a measuring range from a certain curve The distance between the 2 range limiting cursors can be adjusted to less than 1 cm IE GMG Analysis 5 x Ele GMG Edi Display Options Info Help Measurement 1 m x Sliding Friction Coefficient p Diagram Average GMG edited C m 0 77 valid 24 28 Rubber EH VW Scan2 0 49 valid 24 28 Rubber E Scan3 0 45 valid 24 1 28 Rubber EH Scan4 0 50 valid 242 30 I Rubber WI Scan5 0 46 valid 24 3 29 Rubber Average of scan 3 5 0 47 r BMG p Scan editing Surface preasure N cn FS PGSIGTI M 13cm 85 rei Ti Cursor 1 EM Last Calibration m Heset 11 11 39 E d J Distance 123cm Waiting for instruction Recordset from GMG The appropriate average value of the selected range is displayed in the column treated average value Below the column of the 5 scans the average value of scans 3 to 5 is displayed if these 3 scans 3 to 5 have been valid By clicking on the button Return the cursor positions return to the original range selected by the instrument with the fu
10. y be poorer To achieve highest printing quality the printer has to be adjusted to grayscale printing Information The function Help is not yet installed License Agreement GTE ISSUES YOU A LICENSE FOR THIS SOFTWARE ONLY UNDER THE STIPULATION THAT YOU RECOGNISE ALL CONDITIONS LAID DOWN IN THIS LICENSE AGREEMENT PLEASE READ THE CONDITIONS CAREFULLY BEFORE INSTALLING THE SOFTWARE WITH THE INSTALLATION OF THE SOFTWARE YOU ACKNOWLEDGE THAT YOU ARE IN AGREEMENT WITH ALL CONDITIONS LAID DOWN IN THIS LICENSE AGREEMENT License and Warranty The media on which you receive GTE software are warranted not to fail to execute programming instructions due to defects in materials and workmanship for a period of 90 days from date of shipment as evidenced by receipts or other documentation GTE will at ist option repair or replace software media that do not execute programming instructions if GTE receives notice of such defects during warranty period GTE does not warrant that the operation of the software shall be uninterrupted or error free GTE believes that the information in this manual is accurate The document has been carefully reviewed for technical accuracy In the event that technical or ypographical errors exist GTE reserves the right to make changes to subsequent editions of this document without prior notice to holders of this edition In no event shall GTE be liable for any damages arising out of or related to this document or the information
Download Pdf Manuals
Related Search