User Manual - Pro-Ject Audio Systems
Contents
1. Project INSTRUCTIONS FOR USE Pro Ject 2 Xperience SB 2 Pro Ject Audio Systems Pro Ject 2 Xperience SB Ortofon 2M Silver Revision 2015 02 10 Pro Ject 2 Xperience SB Controls features and connections O1 amp ND 7 17 10 11 12 13 14 15 16 18 19 20 21 22 Motor transport foam inserts Motor pulley Drive belt Sandwich platter Tonearm counterweight 5a Downforce scale Tonearm lift lever Tonearm rest and removable transport lock Tonearm tube 8a Tonearm base Lid Lid hinges Hinge fasteners Power supply socket Phono output sockets and earth connection Anti skating stub with anti skating weight adjustment scale Anti skating weight Anti skating weight support Power switch Headshell with finger lift and optional fitted cartridge Ortofon 2M Silver Motor Adjustable tip toe feet with anti scratch cups Screw down record clamp Connection cable not shown Universal power supply not shown Single adapter not shown Pro Ject Audio Systems Pro Ject 2 Xperience SB Ortofon 2M Silver Revision 2015 02 10 3 Dear music lover thank you for purchasing a Pro Ject Audio System s record player In order to achieve maximum performance and reliability with this record player you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse ies Important notice The record player is supplied without2. plinth the acoustic energy emanating from your loudspeakers during replay It is therefore recommended that the lid be removed for optimum sound quality The record player should be positioned on a low resonance surtace such as wood or multiple layer ply board to avoid structural vibrations disturbing replay Adjusting the vertical tracking angle vta Put a record on the platter When the needle is lowered into the record groove and the tonearm is not resting on the lift arm the tube of the tonearm should be parallel to the surface of the record If this is not the case loosen both screws in the tonearm base just enough to allow vertical movement of the arm pillar without force and slide the arm up or down until it is parallel Carefully retighten the screws without applying excessive force which would deform the arm pillar finger tight is quite sufficient Adjusting the azimuth The cartridge needle must be vertical in the record groove in Azimuth setting screw order to trace the groove wall modulations correctly A small screw at the bearing end of the arm allows incorrect azimuth to be corrected if your needle is not mounted exactly perpendicular to the cartridge body which is often the case t ce Slacken off the screw just enough to be able to revolve the arm tube without applying force Please note do not remove the screw completely With the aid of a good magnifying glass adjust the needle until it is vertic
3. No earth connection from cartridge or arm or arm cable to amplifier or earth loop Distorted or inconsistent sound from one or both channels e Record player is connected to wrong input of amplifier or MM MC switch incorrectly set e Needle or cantilever damaged e Wrong r p m drive belt overstretched or dirty platter bearing without oil dirty or damaged Service Should you encounter a problem which you are not able to alleviate or identify despite the above information please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Guarantee repairs will only be effected if the unit is returned correctly packaged For this reason we recommend keeping the original packaging Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide Please remove these parts and pack them separately lid 10 counterweight 6 anti skating weight 16 platter 5 and belt 3 Fit the cartridge protection cap Insert the transport lock for the tonearm 18 prior to carefully packaging the record player Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions neg for use and or by transportation without the original packaging Modification or change to any part of the pr
4. The record player has gold plated female RCA phono sockets 13 so you can substitute the interconnect cables supplied with higher quality cables such as the Pro Ject Connect it interconnect cables for connection to the amplifier if you wish Use the Phono input sometimes labelled gram disc or RIAA on your amplifier Make sure that the phono input offers correct matching and amplification for the type of cartridge used Line inputs such as CD Tuner Tape or Video are not suitable Take care to connect the lef and right channels correctly The right channel is usually marked red the left channel black or white Check the manual supplied with your amplifier for relevant information An earthing wire may be connected to the screw terminal between the sockets if you encounter hum problems when using the record player If your amplifier does not have an input suitable for phono cartridges you will require a separate phono amplifier stage for MM or MC cartridges which is then connected between the record player and a free line level input of the amplifier For detailed product information regarding Pro Ject Audio interconnect cables and phono amplifiers please refer to the Pro Ject website www project audio com ES The recommended load impedance for the factory fitted cartridge is 47kohms MM input Mains power connection The turntable is supplied with the universal power supply with 3 exchangeable sockets adapters suitable for all countries Select
5. al in the groove i e perpendicular to the record s surtace Ideally this should correspond to the top surtace of the cartridge body being parallel to the record surface When you are satisfied that the needle is vertical retighten the screw carefully Please note Under no circumstances should the arm tube be adjusted with the needle still in the record groove Irreparable damage may be caused to the cantilever suspension The arm must be lifted to make each adjustment and lowered afterwards to check it Fitting and connecting the cartridge All cartridges with half inch mounting holes can be fitted Leaving the needle s protection cover on fit the cartridge to the headshell using the screws supplied with the cartridge by passing one screw through each slot in the headshell 19 Do not tighten the nuts yet Connect the tonearm wires to the cartridge pins as follows white left channel positive L red right channel pos R green right channel return R blue left channel return L The full sound quality of the record player can only be achieved if the cartridge is correctly adjusted Particular tools like the Pro Ject alignment tool are required to accomplish this job properly If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of your Pro Ject dealer to accomplish this task for you Adjusting a cartridge and tonearm calls for the greatest care in order to avoid damagi
6. cartridge or with a factory fitted and adjusted cartridge Ortofon 2M SILVER The following instructions for adjusting the cartridge are provided in case the cartridge is replaced by a different model at a later date During assembly and adjustment of the deck small parts could be lost if not carefully placed in a suitable receptacle Before starting assembly make yourself acquainted with the parts listed above and correspondingly numbered in the technical drawings above Separately packed items are marked with an asterisk Safety instructions The power supply is used to connect and disconnect the unit from the mains Make sure that the plug is easily accessible at all times Hold the plug when unplugging the power cord Never handle the power cord while your hands are wet or damp Avoid letting liquids enter the device Never place any item containing liquid such as a flower vase V on or near the device Never spill any liquid on the device Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Keep plastic bags away from children to prevent any risk of suffocation Set up The deck is supplied partially disassembled and carefully packaged for safe transport Carefully remove all parts from the transport packaging Screw the three feet 21 onto the threaded bolts located on the un
7. derside of the plinth Make sure the surface you wish to use the turntable on is level use a spirit level before placing the turntable on it Remove the two motor transport foam inserts 1 which secure the motor 20 during transportation Carefully place the platter bearing housing over the bearing axle Level the plinth using a spirit level and the adjustable feet 22 Fit the drive belt 3 around the platter 4 and the motor pulley 2 Avoid getting sweat or grease on the belt as these will deteriorate the performance and reduce the belt s lifespan Use absorbent kitchen paper to remove any oil or grease from the outer edge of the platter and the belt Remove the transport lock 17 from the tonearm Store it together with the two motor transport foam inserts 1 in the original packaging so they are available for any future transportation neg Please note We recommend to use the record player without a mat on the platter Cartridge downforce adjustment The counterweight 5 supplied is suitable for cartridges weighing between 5 7 5g counterweight no 28 Alternative counterweights for cartridges weighing between 10 14g no 29 7 10g no 46 are available as accessory parts Pushing carefully turn the counterweight 5 onto the rear end of the tonearm tube 9 so that the downforce scale 5a shows towards the front of the player Lower the armlift and position the cartridge in the space between arm rest and platter Care
8. fully rotate the counterweight 5 until the armtube balances out The arm should return to the balanced position if it is moved up or down This adjustment must be done carefully Do not forget to remove the cartridge protection cap if fitted Once the arm is correctly balanced return it to the rest Hold the counterweight 5 without moving it and gently revolve the downforce scale ring 5a until the zero is in line with the anti skating stub 14 Check whether the arm still balances out Pro Ject Audio Systems Pro Ject 2 Xperience SB Ortofon 2M Silver Revision 2015 02 10 Rotate the counterweight counter clockwise seen from the front to adjust the downforce according to the cartridge manufacturer s recommendations One mark on the scale represents 1 mN 0 1g 0 1 Pond of downforce EA Please note Adjust the downforce prior to installing the anti skating weight The recommended downforce for the factory fitted cartridge is 18mN Anti skating force adjustment The anti skating force must be adjusted corresponding to the downforce as follows 3 2 D Downforce Groove in the stub 15 10 14mN 1 from bearing rings 15 19mN DE 4 20mN and bigger a 1 i 14 Hang the loop of the thread of the anti skating weight in the groove of the anti skating stub 14 corresponding to the downforce applied to your cartridge and feed the thread through the loop of the wire support 16 Connection to the amplifier
9. ng the cartridge or tonearm bearings Leave this work to your dealer if you are in any way unsure of the necessary steps and precautions to be taken 6 Pro Ject Audio Systems Pro Ject 2 Xperience SB Ortofon 2M Silver Revision 2015 02 10 Maintenance and cleaning Your record player requires little or no regular maintenance Remove dust with a slightly moistened antistatic cloth Never use a dry cloth because this will create static electricity which attract more dust Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching VA Always disconnect the record player from the mains power supply as a precaution before maintenancel Technical specifications PRO JECT 2 Xperience SB Pro Ject 9cc Evolution Nominal speeds Speed variance Wow and flutter Signal to noise Effective tonearm mass Effective tonearm length Overhang Power consumption Outboard power supply Dimensions W x H x D Weight 33 45 r p m 33 0 12 45 0 28 33 0 12 45 0 11 70dB 8g 9 230mm 18mm 4W gt 0 5W standby mode 15V 800mA DC universal power supply 460 x 160 x 360mm dust cover open 460 x 400 x 445mm 8 kg Technical specifications MM Cartridge O
10. oduct by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer Pro Ject Audi tems is a Regist T k PAS Audie syslems isa Registered Tradera The information was correct at the time of going to of H Lichtenegger press The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development This guide was produced by Pro Ject Audio Systems Copyright 2015 All rights reserved 8 Pro Ject Audio Systems Pro Ject 2 Xperience SB Ortofon 2M Silver Revision 2015 02 10 Accessories Instruction for use onearm transport lock 7 fr a Motor pulley cover p LE Power supply Counterweight LT 3x Feet Pro Ject Audio Systems Pro Ject 2 Xperience SB Ortofon 2M Silver Revision 2015 02 10 9
11. rtofon 2M Silver Frequency range Channel separation Output voltage Recommended load impedance Compliance stylus type Recommended tracking force Weight 20 22 000Hz 23dB 1kHz 4mV 47kohms amplifier connection MM input 20um mN elliptical 18mN 7 2g Pro Ject Audio Systems Pro Ject 2 Xperience SB Ortofon 2M Silver Revision 2015 02 10 7 Potential incorrect use and fault conditions Pro Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances Therefore the following list of common fault symptoms is included The platter doesn t turn although the unit is switched on e The unit is not connected to the mains power supply e No mains at the socket e Drive belt is not fitted or has slipped off No signal through one or other channel or both channels e No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier This could be due to a faulty plug broken wire or solder joint or simply loose plug socket connection Phono input not selected at amplifier Amplitier not switched on Amplifier or speakers defective or muted e No connection to the loudspeakers Strong hum on phono input e
12. the correct adapter for your country and insert the adapter to the exchangeable part of the power supply Connect the low voltage plug from the power supply to the socket 12 on the rear of the record player before connecting the power supply to the mains Fitting the lid Fit the lid dust cover 9 carefully over the hinge prongs and adjust the screws 11 until the lid stays open where you want it to without being too stiff to open or close Switching on and off Press the button START to start the turntable For change the speed from 33 r p m to 45 r p m please press the START button again Speed is correct when the LED diode stops blinking To switch turntable to STAND BY mode please hold the button START for 3 seconds nes For detailed product information please refer to the Pro Ject web site www project audio com Pro Ject Audio Systems Pro Ject 2 Xperience SB Ortofon 2M Silver Revision 2015 02 10 5 Playback of vinyls Remove stylus guard from cartridge 19 Start motor for platter rotation Carefully move Headshell with finger lift 19 to lead in groove of record Move tonearm lift lever 6 to down position Adjust amplifier volume to desired level Amplifier input should be set to Phono position If a Tape Monitor functionality is available only activate when recording unit is switched on Useful tips The lid is not only a dust cover but also a resonant structure likely to be excited by and to pass into the
Download Pdf Manuals
Related Search