Home

iSocket Environment Pro (EN)

1. Store conditions Important notes While the product can operate at low temperatures below zero this is not supported due to the technical specification for most SIM cards A SIM card is not supplied with the device and is therefore not a part of the device You must not turn on the device when the temperature falls below zero the device must be already turned on at this moment and then the heat from the electronics will compensate for the low ambient temperature You must not turn on the device if there has been an abrupt change of conditions from cold to warm or vice versa Please wait a few hours to stabilise conditions before turning on the device Weight Net Gross 258g 0 56lb 410g 0 9lb Temperature sensors ITS00J 7g 0 240z ITS30J 729 2 50z Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 24 English iSocket Environment Pro www isocketworld com 17 Troubleshooting Please read the safety instructions carefully Chapter 2 as well as the warranty terms Chapter 18 You may not repair the device yourself Here are descriptions of the possible problems and their rectification Only the simplest problems are mentioned More information can be found on the website www isocketworld com Some of the described situations may not be a malfunction If you are unable to eliminate any problem yourself then during the warranty service you can take the device to the store from which you bo
2. Monitoring Rooms Using Sensors With iSocket Environment Pro you can set up security or safety monitoring of your premises You can connect various sensors motion sensor door opening detector smoke detector water sensor etc on the input black 3 5mm jack of your iSocket Notification will be sent to your cell phone when the sensor is activated Both N C and N O types of sensors are supported The output can also be controlled by input you can set up a particular time for which main power socket should be switched on or off when a sensor is activated This allows you to activate external equipment which will behave according to your specific environment e g pump will start to drain water when the water sensor detects a signal or a siren will be activated when door movement is detected Unique iSocket Smart Software installed on your iSocket provides plenty options for configuration which allows you to create a really advanced but at the same time simple system This section only provides brief explanations needed for a specialist to configure the device and not a detailed explanation If you do not have the required skills then ask for help from a specialist The features described in this section are supplementary options only and should not be considered a substitute for professional security systems Nevertheless at a reasonable cost you can set up simple protection for your home or office because we sell ready to go pre wired senso
3. should not be activated on the phone from which you are sending messages or making calls to iSocket 6 1 Confirmation of SMS commands If you activate this notification you will be informed about each command execution It is the default setting but you can disable these notifications to save the cost of SIM card messages Command Description Response Type SMSCONFIRM ON Response messages to SMS commands will be SMSCONFIRM ON OK Conf sent SMSCONFIRM OFF Do not send response messages to SMS SMSCONFIRM OFF OK Conf command SMSCONFIRM Information about SMSCONFIRM configuration SMSCONFIRM ON OFF Inf The next commands are not affected by the SMSCONFIRM setting due to the specific nature of the commands STATUS TEMPERATURE RUNTIME SHOWALARMLOG CREDIT HARDWARE SERIALNUM FIRMWARE DATE and all information commands Inf 6 2 Confirmation for Phone Calls When managing by phone call your command will be also confirmed by return SMS but you can configure the device to call back to the mobile phone instead of sending SMS In this case iSocket will call to your phone within about 10 seconds and then hangs up So SIM card credit will not be spent This allows you to perform reboot or switch operations free of charge Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 12 English iSocket Environment Pro www isocketworld com Command Description Respon
4. RELAYTIME ON120 As soon as the door is opened you will get an SMS and the siren will sound for maximum 2 minutes or until the door is closed Example 3 motion detection with siren A motion sensor is connected to the input and a siren to the output You want the siren to sound for 10 seconds each time motion is detected and you get a notification by SMS You should configure RELAYTIME ON10 and ALERT SMS As soon as motion is detected you will get an SMS and the siren will sound for 10 seconds If new motion is detected after one minute or more you will get another SMS and the siren will sound again for 10 seconds 9 4 Alarm Function We assume that sensors have been connected and configured and a phone number for notifications has been installed Now when you leave the home or office you can activate the Alarm Function Now when the sensor is triggered the event will occur according to configuration For example you will receive an alert and or equipment connected to main power socket will be switched on or off Before entering on returning room you need to deactivate the Alarm Function Command Description Response Type ALARMON Switch sensors to standby mode activates the Alarm ALARMON OK Ctrl Function ALARM function Enabled ALARMOFF Deactivates standby mode for sensors nothing happens ALARMOFF OK Ctrl if sensor is triggered ALARM function Disabled ALARM Information about Alarm Function status ALARM function Disa
5. a password Password 12345 11111 abcde and other such passwords are not secure NOTE Don t forget to add the old password before the command PASSWORD x if you are going to remove password protection or update the password Command Description Response Type PASSWORD 12abc Set password 12abc PASSWORD OK Conf PASSWORD NO Disable password PASSWORD NO OK Conf 5 3 Configuration of the Numbers for Alerts Before enabling different alerting Chapter 7 3 9 2 and 10 you must setup at least one number for alerts There are few optional ways to setup this number One is the feature Make me boss see introduction in the Quick Start Chapter 3 Step 3 and more in Chapter 5 1 Another option is the feature Alert me send the command ALERTME from the number which you want to be the number for alerts and the system will automatically assign the phone number from which you have sent it as the number for all types of alerts You can send ALERTME from any number which is included on the security list Chapter 5 1 You can also use the command ALERTNUMBER to add a number for alerts manually see description in the table below Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 11 English iSocket Environment Pro www isocketworld com NOTE Make sure that you don t use the hide my number option for the number from which you execute the command ALERTME and make sure that the num
6. all senders By default this option is set to ON so that during the familiarisation period you can get all responses about errors and will not be confused when there is no response from the device Once you are familiar with the device you can then disable the error message responses In the beginning however we strongly recommend configuring the list of allowed numbers Chapter 5 1 and keeping the option SMSCONFIRMUNAUTH which is set to OFF by default Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 13 English iSocket Environment Pro www isocketworld com 7 Measurement and Control of Temperature iSocket Environment Pro supports one external digital temperature sensor that can measure the temperature of different elements air liquid solid etc from 55C 67F to 120C 248F with an accuracy of 0 5 C You can buy sensors with different lengths of cable from us Sensors are waterproof The sensor must be connected to the RED 3 5mm jack socket on the rear of device y Short sensor to measure temperature near a device Can be a good option if you want to monitor the temperature just inside a zt room No messy cables Model ITSOOJ Sensor with long cable e g 3m 10ft Can be a good option to measure temperature outside or temperature of a liquid or some surface The probe has a wing for screwing A sensor with a long cable is also a good option if the iSocket unit is located clo
7. below because all the next numbers from which you try to execute the MAKEMEBOSS command will already be treated as non authorised Command Description Response Type MAKEMEBOSS This will add the number from which you Your phone number has been Conf send message to the list and will enable assigned for all types of alerts security list SECLIST ON will be active and was added to security list also it will add your number for all types which has been activated of other alerts Chapter 7 3 9 2 and 10 SECNUMBER 35 Add new number to security list SECNUMBER 3589123456789 Conf 89123456789 OK SECNUMBER Delete specific number from security list SECNUMBER 3589123456789 Conf 3589123456789 OK SECNUMBER ALL Delete all numbers from the list SECNUMBER ALL OK Conf SECNUMBER Request for security list numbers SECNUMBERs 3589123456789 Inf 3589000000555 SECLIST ON Activate security list SECLIST ON OK Conf SECLIST OFF Disable security list SECLIST OFF OK Conf SECLIST Information about security list activation SECLIST OFF ON Inf Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 10 English iSocket Environment Pro www isocketworld com Telephone numbers must be added in international format with country code without spaces or hyphens Here are two UNITED STATES examples of how to add and remove number 5555555 SECNUMBER 12125555555 example of adding numbe
8. disable the switch of a remote device Do not use external equipment with a faulty plug Do not connect to appliances which cannot be left unattended e g certain heaters Do not exceed power load limit and other electrical parameters specified in the technical characteristics Check the power of the connected device The device is intended only for domestic private non commercial use Do not use in emergency environments e g military hospitals etc This product is not designed for safe disconnection of the controlled equipment from power network the device is not equipped with a residual current device RCD Make sure that your home electrical network meets safety standards The product is designed for indoor use in dry area Do not use it in wet or chemically aggressive environments For example do not use it in the bathroom It is also not designed for industrial operation in aggressive environments Do not use this device if the casing is damaged Do not shake or drop the product This could cause damage Keep away from direct sunlight Keep out of reach of children Block access to the management and set up of the device to unauthorised users Chapter 5 Read additional safety information in Chapter 18 iSocket Systems hereby declares that this iSocket Environment Pro complies with the essential requirements and other relevant provisions of Directive 1999 5 EC At the end of the product s useful life please dispose
9. information and content included on this User Manual including but not limited to text tables graphics logos icons images is the property of iSocket Systems or its suppliers and is protected by copyright laws You may not modify copy distribute transmit display publish sell or license any information from this User Manual without the express written consent of iSocket Systems and any applicable third party You may not create derivative works or use any information available in this User Manual for commercial or public purposes without the express written consent of iSocket Systems or any applicable third party In addition you may not reproduce transmit transcribe store in a retrieval system or translate into any human or computer language any part of the material from this User Manual in any form or by any means whatsoever without the express written consent of iSocket Systems
10. standard size SIM card from a GSM operator to be installed in the unit If you use a prepaid card you might need to activate it first with an unlocked GSM cell phone More information is available from www isocketworld com prepaid Install SIM card into the special slot and push until fixed you will hear a click SIM card orientation is shown on the front side of the device Do not insert or eject the SIM card on a running device Switch off the device before you insert or eject SIM card Do not use SIM cards that contain messages Remove all messages from the SIM card Do not use SIM cards with NFC chip embedded in a SIM chip for payments from mobile phone NOTE You must disable PIN code authorisation for the SIM card You can only disable PIN authorisation by using mobile phone that support standard size SIM card Insert the SIM card into mobile phone and disable PIN usage using the phone menu You can find more information in the manual for the phone or ask assistance from the shop where you purchased the mobile subscription If you have forgotten to disable PIN code the GSM indicator will be blinking every second and the POWER and OUT indicators will signal this by specific blinks see Chapter 15 The same blinking can occur when the SIM card is not inserted correctly or is damaged Step 2 Apply power to the device Connect iSocket to a wall socket POWER and OUT indicators blink three times simultaneously If everything is funct
11. temperatures TFALLALERT OFF Disable temperature fall alert TFALLALERT OFF OK Conf TFALLALERT Show current settings for TFALLALERT TFALLALERT 15C 60F Inf 8 Date and Time Date and time are used for logging alarms Chapter 9 3 and to configure the scheduler Chapter 11 The date can also be seen in the STATUS response The device automatically sets the date as soon as you start to use it No action is required However if for some reason at the beginning of the operation an incorrect date or time was set and then set it again manually or automatically Automatic date time settings are based on the GSM operator s network date time The device saves date and time settings for several hours after a power failure Command Description Response Type DATESMS This message is automatically set with the date DATE yy mm dd Conf based on time taken from the SMS hh mm ss zz OK DATE yy mm dd hh Manually set the date and time DATE yy mm dd Conf mm ss zZz zz is GMT time zone hh mm ss zz OK DATE Request for actual date and time in device DATE yy mm dd Ctrl hh mm ss zz Would you like to see more features or is there something in our software or documentation that you dislike You are welcome to send us your feedback http www isocketworld com feedback Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 17 English iSocket Environment Pro www isocketworld com 9
12. the POWER and OUT indicators blink 3 times and the device starts to search the network Your device is now returned to the original factory configuration NOTE All your personal settings will be erased during this reset procedure Default factory setting Main socket is switched off SMSCONFIRM ON THERMOSTAT HEATING Alarm function is deactivated RINGCONFIRM SMS SWITCHOFFTEMP 10C 50F Scheduler is empty ERROR ON SWITCHOFFALERT OFF Thermostat is not activated SMSCONFIRMUNAUTH OFF TRISEALERT OFF RESTARTIME 10 RELAYTIME 0 TFALLALERT OFF RING NOACTION SENSORTYPE NO TSENSFAILALERT OFF SECLIST OFF ALERT SMS POWERALERT ON PASSWORD NO CRDITUMS NO POWERSTATE REMEMBER Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 23 English iSocket Environment Pro www isocketworld com 15 LED Indicators The LED positions were described in Chapter 1 Below we list possible LED modes POWER green Lights constantly Blinks 4 times per second then lights 2 seconds Blinks every second Blinks 4 times per second GSM blue Blinks every second Blinks every 3 seconds OUT red No light Lights constantly Blinks 4 times per second Input power to device is OK SIM card problems missed incorrect placed PIN protection is enabled Alarm Function is enabled sensors are not in active status Sensors triggered so sensors in active status Not logged to GSM network yet searching the same blinking if PIN p
13. Description Response Type SWITCHOFFALERT ON Enable SMS sending when SWITCHOFFALERT ON OK Conf SWITCHOFFTEMP is reached and main socket is therefore deactivated Works only if thermostat is enabled SWITCHOFFALERT OFF Disable above alert SWITCHOFFALERT OFF OK Conf SWITCHOFFALERT Show current settings for SWITCHOFFALERT OFF ON Inf SWITCHOFFALERT TSENSFAILALERT ON Enable sending alerts if some TSENSFAILALERT ON OK Conf temperature sensor failed TSENSFAILALERT OFF Disable failed alerts TSENSFAILALERT OFF OK Conf TSENSFAILALERT Show current settings of TSENSFAILALERT Inf TSENSFAILALERT ON OFF TRISEALERT 35C Set the temperature at which you TRISEALERT 35C 96F OK Conf should receive a temperature rise alert or Values from 55C to 120C or from 67F to 248F Do not forget to type C TRISEALERT 96F means Celsius or F means Fahrenheits after value Only integer values must be used Please only use even numbers for Fahrenheit temperatures TRISEALERT OFF Disable temperature rise alert TRISEALERT OFF OK Conf TRISEALERT Show current settings for TRISEALERT TRISEALERT 35C 96F Inf TFALLALERT 15C Set the temperature at which you TFALLALERT 15C 60F OK Conf should receive a temperature fall alert or Values from 55C to 120C or from 67F to 248F Do not forget to type C TFALLALERT 60F means Celsius or F means Fahrenheits after value Only integer values must be used Please only use even numbers for Fahrenheit
14. Pro www isocketworld com IMPORTANT NOTES e Do not insert alarm sensors to the red 3 5mm jack which is the socket for the temperature sensor only e Do not insert or remove sensors on a running device Switch off the device before you insert or remove sensors e Check that the sensor is inserted to the 3 5mm black jack socket to the very end Connection is taught and you have to ensure that there is no gap between connector of sensor and jack socket otherwise you may receive false alarms e You can connect several sensors in parallel but the sensors will not be recognised individually All sensors must be configured as N O in this case see table below and follow instruction supplied with specific sensor e The total power consumption of the sensors connected should not exceed 300mA e We recommend that you only use approved sensors purchased from us failing which we will not be held responsible for the operation of the device f you intend to install many different sensors we would recommend you take a look at our professional equipment from iSocket Smart House family on www isocketworld com e g iSocket Smart Relay 9 2 Sensor Activity Alerts iSocket Alarm Notifier iSocket Alarm Notifier a feature of the iSocket device which will notify you in the event of a break in and some other case when sensor was activated You can receive notifications in various ways iSocket Environment Pro can call you or send an
15. RESTARTTIME 5 seconds Inf STATUS Request for main power socket status Power socket ON Ctrl temperature GSM signal date sensor s status Signal Good 67dBm TEMP 25C 77F ALARMF Disabled ALARM status No act Time y m d h m s TEMPERATURE Informs about temperature See details in Chapter TEMPERATURE 25C 77F Ctrl 7 RUNTIME Informs how long main power socket has been Power socket is ON from Ctrl turned on since last restart or power on If you y m d h m s turn on the main socket manually before the correct date was installed on the device the start up time of the device will not be recorded correctly 4 2 Managing by Phone Call The main socket for external electrical equipment can also be managed by mobile or landline phone For example you can call to the phone number of the SIM card in the device and the equipment connected to the device e g modem will be restarted After a call to iSocket the action occurs immediately The action must be pre configured There is no action configured by default Keep in mind that you are not able to configure the active actions if the security number list Chapter 5 1 is not configured This is because the password protection is not available for calls so anyone can call to the SIM card number if there is no security numbers list protection and this call may cause unwanted reboot Accordingly if you are going to disable the security numbers list protection
16. SCHEDULER hh This command adds a new rule for a specified SCHEDULER hh mm Ctrl mm day action time valid for all days within a week ON OK SCHEDULER hh mm Delete record for configured time SCHEDULER hh mm OK Ctrl SCHEDULER ALL Remove all tasks SCHEDULER ALL OK Ctrl SCHEDULER Request for scheduler configuration 11 59 AON Inf any day 1 Monday 2 Tuesday 3 Wednesday 4 Thursday 5 Friday 6 Saturday 7 Sunday Hours and minutes must be typed with first zero so 08 and not 8 Actions ON Turn on main power socket OFF Turn off main power socket INF Send status of iSocket STATUS command execute AON Alarm function activation premises will be under surveillance AOF Alarm function deactivation disable premises surveillance Examples SCHEDULER 08 00 ON SCHEDULER 20 30 OFF SCHEDULER 09 00 1 AON SCHEDULER 18 00 5 AOF SCHEDULER 17 00 6 INF Turn on main power socket every day at 8 00 Turn off main power socket every day at 20 30 Activate Alarm function every Monday at B 09 00 Disable Alarm function every Friday at B 18 00 Send status of iSocket every Saturday at 17 00 11 iSocket Power Notifier amp Status After Resumption of Power Supply iSocket Power Notifier this feature of the iSocket device will notify you in the event of a power failure and or the restoration of the power supply Your iSocket is equipped with a high quality Li ion re chargeable battery with excess capacity unlike other c
17. SMS when the sensor is triggered You can also be informed by SMS on each change of sensor s status change of logical value To enable such notifications you must setup at least one number for alerts see Chapter 5 3 Place the most important numbers for notifications at the beginning of the list Read below to understand the reason Notification cycle logic If you have configured notifications by messages the device will send messages to all numbers If call alerts are configured the device will call you within about 20 seconds If you answer pick up the handset within these 20 seconds the call notification cycle is considered complete and no one else from the list receive call or message Thus by answering the call you will stop the notification cycle That means that you are aware of the alarm event and must act accordingly If you don t answer or if you drop the call hangs up after 20 seconds the device will try to reach the next number on the list The device will only try to call each number once The call notification cycle is considered complete as soon as someone answers If no number is answered during the call cycle the device will send messages to all alert numbers thus completing the notification cycle SMS notification cycle is considered complete as soon as all messages have been sent by the device Therefore the most important numbers for notifications have to be placed at the beginning of the list Alarm detection and aler
18. an carry out a simple test Try to call to the device s number If this works you will hear a ringing tone instead of a subscriber not available signal only if RINGZNOACTION If you are sure that the device is online you need to look for other possible problems One possibility is that the phone number from which you send a message is unauthorised and therefore you will not receive any messages and no action will be carried out Chapter 5 1 A mistake in writing the command could have occurred and error suppression could have been set ERROR OFF In this case you would not know if you had made a mistake in the command Check your outgoing messages to see what command was sent and check that it was written correctly according to the manual Read about other potential problems below Possible malfunction The OUT indicator reports an error blinking 4 times per second Possible solution If the OUT indicator blinks 4 times per second even only occasionally e g at the start of the device it is likely that there is some problem with the SIM card Check that the SIM card in the device doesn t contain any data such as stored phone numbers and messages If the SIM card has data on it then clean it using your cell phone Also try using another SIM card If the OUT indicator is blinking constantly and the blue GSM indicator is always off there is probably a problem with the power of the GSM module Contact the service department Possible malfunct
19. ber is in the security list If the system cannot recognise the number or if the number is not authorised it will not add it to the number for alerts Command Description Response Type ALERTME This will automatically add the number from Your phone number has Conf which you send the message to the list for all been assigned for all types of other alerts types of alerts ALERTNUMBER 358 Set the number for alerts manually ALERTNUMBER 358912 Conf 912345678 Instructions how to add a number are similar 345678 OK to those given in Chapter 5 1 see examples there DO NOT ADD THE PHONE NUMBER IN LOCAL FORMAT USE THE FULL INTERNATIONAL NUMBER ONLY WITH COUNTRY CODE ALERTNUMBER Remove number from list ALERTNUMBER Conf 3589123456789 3589123456789 OK ALERTNUMBER ALL Remove all numbers ALERTNUMBER ALL OK Conf ALERTNUMBER Information about numbers ALERTNUMBERs Inf 3589123456789 3589223456789 NOTE Do not keep wrong or non existent numbers in the list of ALERTNUMBERs Do not keep numbers in local format in the list of ALERTNUMBERs use only the international format with country code Ignoring this advice will delay alerts to good numbers 6 Command Confirmation It is important to confirm that the command was executed successfully For this purpose we have implemented notifications of each executed command If you wish to receive execution confirmations the setting hide my number
20. bject to change without notice Current terms are available from http www isocketworld com warranty The warranty terms below apply to customers who purchase products directly from iSocket Systems for personal use Warranty terms for products purchased from dealers may be different Contact the dealer who sold you the product for details Our products are subjected to stringent final quality inspection iSocket Systems guarantees that your device is free from material and production defects iSocket Systems will not be liable for any direct or indirect material loss to the owner or other persons caused by use of this device This warranty only covers production defects The rights and benefits under this guarantee are additional to your statutory rights which are not affected by this guarantee If your device produces any of the defects mentioned above within a period of 12 months after purchase for some countries 2 or 3 years extended warranty is available check our website iSocket Systems offers at its discretion either a free of charge repair or exchange The guarantee applies only for you as the original end customer It does not apply to damage to fragile components such as the housing damage caused by improper use culpable damage damage caused by breakage heat water or acts of God damage caused by unauthorised tampering with the device or exposure to chemicals damage caused by overloading in the house power network The life cycle ofthe re
21. bled Inf Sensor s Connected ALARM status No activity NOTE Entering the house without having disabled the Alarm Function will activate equipment connected to main power socket and or send you alert depend on your configuration In this event the Alarm Function can be deactivated manually by using the hidden button Push the hidden button once After this the button returns to the normal operation mode for which it is intended This facility is available should you have forgotten or lost your phone 9 5 Alarm Logs You can read alarm logs which record sensor activity The device keeps the last 10 events sorted by time One of the simplest ways to use this feature is to monitor people entering the room when room was visited Command Description Response Type SHOWALARMLOG Show alarm logs yy mm dd hh ss Ctrl Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 21 English iSocket Environment Pro www isocketworld com 10 Scheduler The main power socket can be controlled in the automatic mode based on pre scheduled rules Some other commands could be executed at pre defined intervals For example enable disable Alarm Function or regularly send status of the device Information about statuses is sent to the alert numbers see Chapter 5 3 for configuration The schedule accepts a maximum of 8 rules Command Description Response Type
22. boot can be performed by a call to iSocket and you can configure them to be absolutely free Thus you may reboot your computer or modem remotely for free See Chapter 4 2 and 6 2 for details For more information about the technical characteristics of isocket Environment Pro see Chapter 16 and also visit our website www isocketworld com Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 3 English iSocket Environment Pro v www isocketworld com Main power socket we Y Plug to connect Socket for connecting a iSocket to the wall external electrical i socket to provide equipment which can o power for device and be controlled remotely for connected U appliance Figure shows v plug socket type CEE 7 4 Schuko model ISGSMT70O7EU POWER Indicator of input o0 power from power Hidden button 6 network Used to switch the gt eg E main socket manual GSM Chapter 4 3 or reset Status indicator for device Chapter 14 GSM network OUT 0 Additional information Indicator of output sonore about the indicators is power for main socket emptis given in Chapter 15 Input for sensors Socket for SIM Socket for TEMPERATURE sensor 3 5mm jack BLACK card standard size 3 5mm jack RED See Chapter 7 See Chapter 9 GSM SIM card NOT FOR TEMPERATURE Warning If you insert the temperature sensor to the wrong SENSOR jack the temperature sensor will be destroyed Pictures below describe
23. ensors from the original Temperature manufacturer are supported Sensors are water proof measurement limits from 55C 67F to Sensor 120C 248F 0 5 C accuracy from 10 C to 85 C Temperature Thermometer and thermostat features temperature measurement provided by SMS turn on off control equipment by thermostat s settings isocket Temperature Notifier send temperature rise fall notifications Indicators POWER green GSM blue OUT red SIM socket Push push type plug in SIM card 3V for standard size GSM contract or prepaid PAYG SIM cards Mobile Network 4 band worldwide GSM 850MHz 900MHz 1800MHz 1900MHz built in antenna iSocket Online 24 7 gets the device back online even after a break in the GSM network Built in Li ion or Li po high quality batteries with excess capacity cater for signal delays in the event of a rechargeable break in the GSM network before sending the power failure alert Charging from internal charger battery about 10 hours if totally discharged iSocket Power Notifier power failure restore alerts Scheduler Scheduling the following functions to be executed at a particular time turn on off relay activation deactivation of Alarm Function sending status with temperature information Security Password phone number list limited configuration interval Operation Operation conditions Indoors dry conditions 10C 40C 14F 104F conditions Store conditions 30C 50C 22F 122F
24. er then unauthorised numbers will receive the message Access deny in response to an attempt to execute any command We do not recommend you to set ON value for this option because unauthorised users who know the phone number of the SIM card can deplete the card s credit with such response messages Therefore we also strongly suggest using protection with security list Chapter 5 1 and not just password protection This is due to the fact that a command typed without a password is considered an incorrect command and the illegal sender will receive command No such command exists on the device in response And he can also deplete SIM card credits by such responses Command Description Response Type ERROR ON Activates sending of information SMS for ERROR ON OK Conf each received SMS command which was not executed due to any error ERROR OFF Disable the error messages responses ERROR OFF OK Conf ERROR Information about ERROR configuration ERROR ON OFF Inf SMSCONFIRMUNAUTH ON Send reports errors not permitted time SMSCONFIRMUNAUTH Conf out to unauthorized numbers ON OK SMSCONFIRMUNAUTH OFF Don t send reports to unauthorized SMSCONFIRMUNAUTH Conf numbers OFF OK SMSCONFIRMUNAUTH Information about SMSCONFIRMUNAUTH SMSCONFIRMUNAUTH Inf configuration OFF ON Generally it should be noted that the ERROR OFF command disables all reports about errors and later configuration for
25. f sensor is activated OK RELAYTIME 0 Do not change status of main power socket when RELAYTIME 0 OK Conf sensor is activated RELAYTIME Information about RELAYTIME value RELAYTIME 0 Inf ALERT SMSCHANGE case If alert type is SMSCHANGE see Chapter 9 2 then the relay returns to the opposite status as soon as the sensor returns to default status regardless of the time configured by RELAYTIME ONxx or RELAYTIME OFFxx However when you configure permanent activation RELAYTIME ON or RELAYTIME OFF returning of sensor to its default status will not affect the relay Opposite statuses means the following If RELAYTIME ON or ONxx then the relay will be turned off after the sensor returns to default status Accordingly if RELAYTIME OFF or OFFxx then the relay will be turned on after the sensor returns to default status This logic is not affected by intermediate statuses of the relay It means that no matter what the relay s status was between the activation of the sensor and returning it to default status behaviour will be the same following above logic ALERT SMS CALL OFF For these types of alerts the relay will change its status only once when alarm is detected The relay will change its status according to the setting configured by the command RELAYTIME NOTE The relay changes its status according to RELAYTIME each time the alarm is activated Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 20 En
26. features in this device as well as functions related to temperature control are optional and cannot be considered as a substitute for professional systems iSocket Systems assumes no liability for damage to property in connection with the operation of these functions The ability to send different types of alerts depends on the mobile network and other factors iSocket Systems provides the best technological solutions to perform these operations successfully but isocket Systems do not allow use of the device for purposes related to life support and assumes no liability for damage to property loss of profit or any other loss in connection with the operation of device The maximum liability is limited by the cost of device in a case of its failure isocket Systems provides protection against unauthorised access to the device but gives no guarantees regarding the impossibility of such access and is not responsible for the consequences of such lack of access iSocket Systems reserves the right to modify the device and its software without further notice Differences in the software not covered in these instructions are acceptable and not considered as defects and cannot be a matter for warranty service Releasing new software including new functions is not an excuse for its replacement under warranty terms and can be done for an additional fee Illegal use of remote listening option and the illegal extraction of information is a violation of the law in most c
27. glish iSocket Environment Pro www isocketworld com The above allows you to configure any behaviour suitable for your environment Example 1 flood detection alarm and water drain The iSocket Water Sensor is connected to the input and the pump to drain water from basement is connected to the main power socket Assuming you do not know how much time the pump requires to drain all the water out of the basement You do not want the pump to circulate permanently but to stop as soon as the water is drained You configure ALERT SMSCHANGE for the water sensor and RELAYTIME ON turn on permanently because you do not know how much time it need As soon as the water sensor detects water the pump will be activated Imagine after 30 minutes the pump has drained all the water The sensor s contact becomes dry and the sensor returns to default status This deactivates the relay and the pump is switched off even though RELAYTIME ON was configured Example 2 door opening alarm with siren A door opening sensor is connected to the input and a siren to the output to main power socket Because of the nature of the door sensor it requires the ALERT SMSCHANGE setting see Chapter 9 2 Alarm detection and alert logic section You want thieves to be frightened off by the siren but you do not want to disturb neighbours permanently with the siren while the door is still open You want the siren to sound for two minutes only Therefore you configure
28. he iSocket from the wall socket You will soon get a power failure alert Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 7 English iSocket Environment Pro www isocketworld com 4 Managing the iSocket Device You can manage the device with SMS commands by phone call or manually SMS management offers more options 4 1 Managing by SMS Commands are sent in form of SMS messages to the SIM card number of the iSocket Messages have the following syntax COMMAND for example STATUS If a password was configured see Chapter 5 then you must use following syntax passwordCOMMAND for example 12345STATUS where 12345 is a password set by the command PASSWORD 12345 more details in Chapter 5 Commands are not case sensitive There are three types of commands on device 1 Configuration commands marked Conf in the tables These commands configure some parameters on the device and usually not always have the syntax COMMAND VALUE so they have symbol after the command name The configuration can only be performed within 30 minutes after device has been powered on or after the last configuration command has been received If you try to configure device after 30 minutes then you will get the message command Time for configuration expired Conf only if ERROR ON see Chapter 6 To disable this limitation you must configure security on device see Chapter 5 Settings are stored in non
29. heap products with weak batteries or an unreliable supercapacitor Using such a battery ensures that the customer will receive a power failure notification even in the event of a break in the mobile network The iSocket Smart Software is able to detect a break and wait for a signal before sending the power failure message The high quality battery allows a delay As soon as the message is sent the device will shut down The battery will be charged later when device is powered again To receive such alerts you need to configure at least one number for alerts see Chapter 5 3 Once numbers have been configured you will receive messages whenever power is interrupted and restored These numbers are also used for other notifications e g for Alarm Function Chapter 9 If you do not want to receive power failure alert you can disable it see table below You can install power resume mode for main power socket The option REMEMBER is the factory default and is suitable for most configurations so you probably will not need to change it Command Description Response Type POWERALERT ON Enable power failure restore alerts POWERALERT ON OK Conf POWERALERT OFF Do not send power failure restore alerts POWERALERT OFF OK Conf POWERALERT Information about POWERALERT setting POWERALERT ON OFF Inf POWERSTATE The main power socket remembers its state POWERSTATE REMEMB Conf REMEMBER and returns to it after the resumpt
30. iSocket Environment Pro User Manual English For all countries www isocketworld com ENGLISH Thank you for choosing iSocket Please take a few minutes to read through these operating instructions carefully before using the product so that you can get full advantage of the functionality and get maximum enjoyment from it Pay special attention to the safety instructions in Chapter 2 Incorrect use could affect your guarantee or jeopardise health or property We reserve the right to make design changes on the device and its software without prior notice Deviations not mentioned in this instruction might exist in the software which is considered acceptable and not considered a defect The latest version of these instructions can be found on our website www isocketworld com Be sure to read the terms of warranty before using the device so that you do not to lose your rights under the guarantee as a result of improper operation Chapter 18 You agree with the terms of warranty and limitation of liability described in Chapter 18 when you purchase this product Please keep these operating instructions in a safe place for easy access when needed We hope you thoroughly enjoy using your iSocket NOTE e The software supplied with this product is the exclusive property of iSocket Systems As an end user you are granted a non exclusive license to use this software solely in combination with the device on which it is installed and with
31. ion The phone from which device was controlled has been lost but the number was recorded in the list of allowed numbers So you cannot control the device any longer Possible solution The device must be reset to the factory defaults and set again with another phone Chapter 15 Possible malfunction The device is behaving strangely e g no response to commands Possible solution Try to reset to factory default and configure the device again Chapter 15 You can also check that the SIM card in the device doesn t contain any data such as stored phone numbers and messages If the SIM card has data on it then clean it using your cell phone Possible malfunction The device doesn t send power failure power restore alerts Possible solution Make sure that the number for alerts is installed properly see Chapter 5 3 Lithium ion batteries are subject to a natural ageing process When the capacity falls below a critical value you will not be able to receive the power failure alerts If this happens during the warranty period you have the Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 25 English iSocket Environment Pro www isocketworld com right to get a replacement battery for your product If you use the device outside the specified temperature range this can also be the reason for not receiving power failure alerts 18 Limits of Warranty and Liability These Warranty and Liability Terms terms are su
32. ion of ER OK power supply to the device POWERSTATE ON The main power socket always turns on when POWERSTATE ON OK Conf resuming power supply to the device POWERSTATE OFF Main power socket is always turned off when POWERSTATE OFF Conf resuming power supply to the device OK POWERSTATE Information about POWERSTATE POWERSTATE REMEM Inf configuration BER ON OFF Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 22 English iSocket Environment Pro www isocketworld com NOTE The unit might sometimes remain turned on after you have disconnected it from the power source This is because of the built in battery If this happens please remove the SIM card from the unit and wait for a while It will switch off after a maximum of 20 minutes 12 Credit Information and Subscription Management experimental NOTE Correct operation of these experimental features cannot be guaranteed We reserve the right to remove these features in future versions of devices The absence or incorrect function of these features on your device will not be covered by warranty You can get SIM card credit information Not all operators provide such service With prepaid cards this service is usually available For the monthly mobile subscriptions it is usually not available You can also activate some UMS codes remotely Command Description Response Type CREDITUMS X To insta
33. ioning correctly the POWER indicator will be a constant light green The GSM indicator blinks once a second during network search and every 3 seconds when the network has been found More information about the indicators in Chapter 15 Step 3 Execute your first command and make yourself the main user Your device with iSocket Smart Software has the unique feature Make Me Boss Send SMS command MAKEMEBOSS to the phone number of the SIM card installed in the unit and it will automatically assign the phone number from which you have sent it as the number for all types of alerts and will also enable protection by the list of phone numbers and will add the number to the list NOTE Make sure that you don t use the hide my number option for the number from which you execute the command If the system cannot recognise the number it will not add it to the number for alerts and to the security list Alternatively you can use the methods of adding these numbers which is described in Chapter 5 1 for SECNUMBER and 5 3 for ALERTNUMBER Please also read the IMPORTANT NOTE in Chapter 5 1 about the specific requirements of some mobile networks First test The device is now ready to work You can carry out a simple test Connect an appliance to the iSocket e g a desk lamp don t forget to turn on the lamp switch Send the message ON to the SIM card number and the lamp will switch on Send the message OFF and the lamp will turn off Remove t
34. lays depends on how often it is turned on and off but iSocket Systems guarantees its function at least during the warranty period Any replacement hardware product will be warranted for the remainder of the original warranty period or thirty 30 days whichever is longer or for any additional period of time that may be applicable in your jurisdiction on condition that the device was purchased through an authorised channel iSocket Systems does not guarantee the preservation of personal settings on the device after its repair Repair or replacement may involve the use of functionally equivalent new or used parts Replaced parts become the property of iSocket Systems The warranty will be lost if safety instructions not complied with see Chapter 2 when using the device and if the conditions of use were violated isocket Systems disclaims any responsibility for damage to health or property suffered as a result of using this device and failure to comply with safety instructions Improper use disassembling or product modification causes warranty loss iSocket Systems does not guarantee that this product will provide uninterrupted operation of the controlled equipment this device is not an uninterruptible power supply UPS This product is not designed for safe disconnection of the controlled equipment from power network the device is not equipped with a residual current device RCD Correct function of the switching function all that is guaranteed Alarm
35. ll UMS code for balance check For CRDITUMS 100 OK Conf ex CREDITUMS 100 Ask UMS code from your mobile operator CREDITUMS NO Remove UMS code for balance from memory CRDITUMS NO OK Conf CREDITUMS Information about CREDITUMS settings CRDITUMS 100 Inf CREDIT Information about balance CREDITUMS Response from mobile Ctrl must be pre installed operator SIMCARD X To manage your subscription by UMS codes Response from operator Conf 13 Version Information Command Description Response Type HARDWARE Reports the name of the product iSocket Environment Pro Ctrl SERIALNUM Reports the serial number of the device S N 1234567898 7654321 Ctrl FIRMWARE Reports the version of the firmware v1 0 0 c iSocket Systems Ctrl 14 Original Factory Settings Each new device has pre configured factory settings These are the so called default values These settings are described below The device can be returned back to these default values at any time The reset button is positioned on the front panel next to the logo see Chapter 1 To reset the device press this button with a suitable thin object hold it for about 10 seconds until the POWER and OUT indicators start blinking simultaneously Then release the button and the reset procedure will start Reset will take about 30 seconds and POWER indicator will blink every second during the reset procedure Then the device will restart
36. mediately the sensor is connected to iSocket Information available in Celsius and Fahrenheits Command Description Response Type TEMPERATURE Informs about temperature in the room TEMPERATURE 25C 77F Ctrl STATUS Request for socket s status and temperature Power socket OFF Ctrl information includes TEMP 25C 77F 7 2 Thermostat iSocket Smart Software has an advanced thermostat feature that allows you to control both heating and cooling systems with a wide choice of settings and be very simple in the same time The thermostat feature allows you to control the main power socket and change it depending on the pre configured switch off temperature The interval between temperature readings from sensors is one minute Command Description Response Type THERMOSTATON Activate thermostat THERMOSTATON OK Ctrl THERMOSTAT HEATING Switch off temperature 10C 50F Note Thermostat is working now THERMOSTATOFF Disable thermostat THERMOSTATOFF OK Ctrl Note Thermostat was disabled THERMOSTAT Set the condition of thermostat Use THERMOSTAT HEATING OK Conf HEATING this value if heating system is Switch off temperature connected to device 10C 50F THERMOSTAT Disabled THERMOSTAT Set the condition of thermostat Use THERMOSTAT COOLING OK Conf COOLING this value if cooling system is Switch off temperature connected to device 22C 72F THERMOSTAT Enabled SWITCHOFFTEMP 10C Set
37. meter oir ie ies Qesaq ctos bui ub eshte tarn bi rper bii tias briser a oia 15 Z2 Thermosbdl 22i x E RERER SER S SRARI ARAS At I DUANE ARMIN RR ANNE RU PERDRE AS DN HUE 15 7 3 Temperature Monitoring Notifications iSocket Temperature Notifier 16 GNERIICIUME QUIM 17 9 Monitoring Rooms Using SEFISOfS iisssasespax sae Eh RRAFEERERKERERIRARRRTRXSRRRA E SERRA RRXGPRA EE 18 9 1 TS0CckeL Sensors desna a E bxotid is a blo xbipubiltssatrbi corn a ad 18 9 2 Sensor Activity Alerts iSocket Alarm Notifier ccccccececeeeeeeeeseeeeseeensneanens 19 9 3 Input Output RelationS sssssssssssssssssrrnnnnnnnnrrrrrssssnnnnnnnnnnnrrnrersnnnnnnnnnnnnnnn 20 9 4 Alarmi FUNCION vac tecsdece se viecccusesctecasscasecus vrusa TuS ecacegscsicestasecesscagniescaus TERESET 21 PES ldugBBis AMe er TTE 21 10 SchedUlBr osdugsbrdi deti a bsorerds boni duo a e a a a 22 11 iSocket Power Notifier amp Status After Resumption of Power Supply 22 12 Credit Information and Subscription Management experimental 23 13 Version Information sse cc icesccsa devs assensceastanewsdeeecsageessanseeeeadeastiaetetesesisvenantasece 23 14 Original Factory Settings 35 2 FRE LER RR AE ARERER RU ERTAT RARE PEENE ARENAEN IM EAR RUE 23 I5 LED Indi c torS tosececednsiudidadcoshiauenahdd a e aaa ai 24 16 Technical Data suistoveteictateieistaveintatevedstalededotalateiaialotatwlaloteiehelac
38. nfiguration window and can be used at any time You will get a response after sending the commands This can be disabled if desired see Chapter 6 If you make a mistake in the command and send an incorrect command you will receive a message COMMAND No such command exists on the device Only Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 8 English iSocket Environment Pro www isocketworld com if ERROR ON see Chapter 6 If a command longer than 30 characters was sent it will be deleted without any response notifications The list of simple commands for management and configuration is shown in the following table The real response may differ from those indicated in the table depending on the command Command Description Response Type ON Turn on main power socket Power socket ON Ctrl OFF Turn off main power socket Power socket OFF Ctrl ON3O Turn on main power socket for 30 seconds Power ON for 30 seconds Ctrl Maximum value is 65000 seconds OFF30 Turn off main power socket for 30 seconds Power OFF for 30 seconds Ctrl Maximum value is 65000 seconds RESTART Restart return to the same status after a certain Power socket restarted Ctrl period of time main socket Time for restart set by RESTARTTIME RESTARTTIME 5 Configures time in seconds for RESTART RESTARTTIME 5 OK Conf command Maximum value is 600 seconds RESTARTTIME Informs about RESTARTTIME value
39. nsor Only one alert will be sent until you change something in thermostat settings and some new failure occurred If a temperature sensor has failed then the thermostat will remain activated but will not operate These two types of alert are related to the thermostat and work only if thermostat is enabled NOTE When a thermostat was deactivated because of temperature sensor failure or when you disable a thermostat manually the relay will remain in the same condition as it was just before thermostat was disabled This means that disabling the thermostat won t change the previous status of relay and you must do it yourself if you need to iSocket Temperature Notifier a feature of the iSocket device which notifies you in the event of the room temperature falling below TFALLALERT or rising above TRISEALERT critical levels This is another type of temperature alert which your iSocket can provide for you This feature does not affect the thermostat and can work independently This feature is not related to output but to temperature sensors connected to the unit If you need to know when the temperature drops below the specified level set TFALLALERT If you need to know when the temperature exceeds the specified value set TRISEALERT Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 16 English iSocket Environment Pro www isocketworld com Command
40. of it at appropriate collection points provided in your country NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures reorient or relocate the receiving antenna increase the separation between the equipment and receiver connect the equipment into an outlet on a circuit different from that to which the receiver is connected consult the dealer or an experienced radio TV technician for help Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 5 English iSocket Environment Pro www isocketworld com Safety Instructions for the Battery This unit use a Li ion battery The safety instruction does not tell you how to maintain the battery because this battery is installed inside the unit It is strictly p
41. other example is air conditioning activation when the temperature exceeds 22C 72F THERMOSTAT COOLING SWITCHOFFTEMP 22C or SWITCHOFFTEMP 72F THERMOSTATON This means that as soon as the room is cooled to 22C 72F the main socket is turned off If current temperature in the room is less than 22C 72F the main socket does not turn on until the temperature rises above 22C 72F 7 3 Temperature Monitoring Notifications isocket Temperature Notifier Before enabling alerts you must set up at least one number for alerts see Chapter 5 4 There are several type of alerts related to temperature in iSocket Smart Software installed on your iSocket Environment Pro switch off alert SWITCHOFFALERT temperature fall alert TFALLALERT temperature rise alert TRISEALERT and alert when temperature sensor has failed TSENSFAILALERT SWITCHOFFALERT enable SMS sending when switch off temperature is reached and a relay was therefore deactivated This just allows you to know that main power Socket was switched off and shows at which temperature this happened This feature is related with thermostat and works only if thermostat is enabled Note It will send an alert every time the switch off temperature was reached so this event could be too often during the work of thermostat We do not recommend to enable this alert eTSENSFAILALERT send alert if some temperature sensor has failed or a reading problem occurred on an active temperature se
42. ountries Before using this function consult with a lawyer iSocket Systems categorically prohibits the use of this device for unlawful purposes and is not responsible for illegal use of the device Please make sure that mobile network is available in the area Bad coverage is not a warranty matter Please ensure that mobile phones are permitted in the area before operating the unit eg hospitals petrol stations etc If the use of a mobile phone is forbidden do not use the device as it can have negative influence to other electronic systems iSocket Systems will not be responsible for changes in mobile operators networks if they for example cancel a service reduce performance change network settings or shut down a network which is required for operation of the device If the device stops operating due to any changes on mobile network it may not be considered as warranty case To get warranty service you must provide proof of payment and this guarantee The guarantee must be duly filled in and must specify the serial number of the device if it does not contradict the legislation of the country where product was legitimately purchased 19 Contacts The most current product and contact information can be found on the World of iSocket website www isocketworld com Thank you for choosing our state of the art products Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 26 English Copyright iSocket Systems 2015 All
43. p Notifications Settings Block access to iSocket management for unauthorised users If there are no security settings then anyone who knows the phone number of the SIM card will be able to manage the device and deplete the card s credit which is not advisable The device uses two methods of protection against unauthorised access e Only allowing access to authorised phone numbers e Authentication by password Both methods can be used separately or together In the first method the device ignores SMS commands and calls from numbers that are not listed The list can contain up to 10 numbers The second method involves the use of individual 5 characters password This password must be typed before the SMS commands without any space or special characters as shown here passwordCOMMAND for example 12abcSTATUS where 12abc is a password set by the command PASSWORD 12abc more details below 5 1 Security Numbers List Settings The security list allows you to configure up to 10 numbers and up to 15 digits for one phone number Below is a list of commands that explain how to activate the security list and how to add a number By default the security list is disabled and does not contain any numbers The first number can be added in a simple way by executing command MAKEMEBOSS see introduction to this feature in the Quick Start Chapter 3 Step 3 However all the next numbers must be added using the command SECNUMBER described in the table
44. r SECNUMBER 12125555555 example of removing number Here 1 is the United States country code 212 is the city code for New York and 5555555 is a 7 digit local number IMPORTANT NOTE Some mobile operators indicate international numbers when transmitting SMS s in our example 12125555555 but during the call such operators indicate number in local format in our example it will be 2125555555 or even 5555555 If such behaviour was noticed in your mobile network you have to add both international and local numbers to the list It means in addition to the international number you must also add the local number by the command SECNUMBER 2125555555 or and SECNUMBER 5555555 If you add a number to the list when the list is not activated the protection will be disabled Do not forget after adding number to activate security list by command SECLIST ON If you deleted all the numbers by command SECNUMBER ALL the protection will be disabled automatically SECLIST OFF became active Make sure that you don t use the hide my number option All numbers that the system does not recognise are considered to be unauthorised numbers We suggest that you always use security list protection even if you use password protection Chapter 6 3 lists more reasons for this 5 2 Password Protection The following table shows how to set a password for managing access The password must consist of 5 characters Do not use a simple combination of numbers for
45. rohibited to replace the battery yourself an authorised specialist must be consulted However this safety instruction does describe the care of units using a Li ion battery Read all the safety information and instructions Failure to comply with the safety information and instructions may cause fire and or serious injury We pay a great deal of attention to the design of every battery to ensure that we supply you with batteries which offer maximum durability and safety Despite all the safety precautions caution must always be exercised when handling devices with batteries Studies have shown that incorrect use and poor care are the main causes of the damage caused by batteries The following points must be obeyed at all times to ensure safe use e Don t throw battery or device with battery into an open fire There is a risk of explosion e Always comply with the storage conditions see Chapter 16 Don t keep the device with its battery in places where the temperature is liable to reach levels outside those specified In particular do not leave the device in a car that is parked in sunshine e If the battery suffers overloading and or overheating the integrated protective cut off will switch off the charging discharging for safety reasons If this happens you will not be able to get a power failure alert Using the battery at temperatures outside those specified in the technical information Chapter 16 will cause chemical damage and ma
46. rotection still activated Logged to GSM network Main power socket is turned off Main power socket is turned on An error or possibly a problem with SIM card see also Chapter 17 16 Technical Data Product iSocket Environment Pro Available Socket Plug Socket Plug CEE 7 4 Schuko Model Number ISGSMT707EU Socket Plug CEE 7 5 French Model Number ISGSMT707FR Socket Plug BS 1363 British Model Number ISGSMT707UK Socket Plug CEI 23 50 S17 P17 Italian Model Number ISGSMT707IT Socket Plug SEV 1011 Swiss Model Number ISGSMT707CH Socket Plug NEMA 5 15 North America Model Number ISGSMT707US Socket Plug AS NZS 3112 Australian Model Number ISGSMT707AU Socket Plug SI32 Israeli Model Number ISGSMT707IL Power Input 100 240VAC 50 60Hz Consumption Stand by power 1W Green Power Output Relay Max switching 16A 250VAC protected by 15A fuse Turn on off or restart of 120VAC 240VAC appliances by sms or call Hidden button For manual switching of main relay and for reset to factory defaults Input for Alarm input for external sensors motion door switch fire CO etc provide 12VDC 300mA Sensors fused by PTC resettable fuse 350mA mini jack 3 5mm connector on the rear of the device BLACK iSocket Alarm Notifier alarm notification over external sensors actuation Input for Mini jack 3 5mm connector on the rear of the device RED colour Only s
47. rs kits with detailed connection instructions 9 1 iSocket Sensors Sensors are not supplied with the device These can be bought directly from us or our dealer network Our wired sensor kits have several benefits compared to wireless solution The most important of them are e high reliability because of the reliable wired connections that use special professional copper alarm grade cable e high security because the connection cannot be interrupted by wireless scanners e maintenance free because you do not need to check and change batteries e mim Water Sensor iin VAN KIT1 for burglar KIT2 KIT3 for fire KIT4 for gas iSocket Water Splitter for alarm alarm leak alarm Sensor for water connecting several Model ISKIT1 Models ISKIT2 ISKIT3 Model ISKIT4 leak alarm sensors in parallel Model ISWSNO1 SPLIT2W15CM Refer to our website www isocketworld com for up to date information about the sensors we have for your iSocket Command Description Response Type SENSORTYPE NO The value depends on the sensor type Set SENSORTYPE NO OK Conf this value if the sensor is N O type SENSORTYPE NC The value depends on the sensor type Set SENSORTYPE NC OK Conf this value if the sensor is N C type SENSORTYPE Information about SENSORTYPE configuration SENSORTYPE NO NC Inf Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 18 English iSocket Environment
48. se Type RINGCONFIRM SMS Send response SMS after call to device RINGCONFIRMTYPE SMS OK Conf RINGCONFIRM CALL iSocket call back to your phone within RINGCONFIRMTYPE CALL OK Conf 10 seconds and then hang up RINGCONFIRM OFF Don t notify results after phone call to RINGCONFIRM OFF OK Conf the device RINGCONFIRM Information about RINGCONFIRM RINGCONFIRM SMS CALL OFF Inf configuration 6 3 Incorrect Commands Later Configuration and Commands From Unauthorised Users If an incorrect command was sent to the device typo mistake for example you will get the command No such command exists on the device response If you have password protection but forgot to specify it before command see Chapter 5 2 you will get the Invalid access password response If you are trying to assign an invalid value to the configuration command you get the message Incorrect value You will get Time for configuration is expired Conf response when you try to send a configuration command after the configuration time is up see Chapter 4 If an unexpected error occurred during the command execution you will get the message Execute error You can disable all the above error messages by setting options ERROR OFF If the security list was configured see Chapter 5 1 and someone tries to execute a command no response will be received until you install SMSCONFIRMUNAUTH ON If you set ON value for this paramet
49. se to the heating system which may i E affect temperature measurements A l A sensor with a cable will allow you to install d a the sensor far from the source of heating in that case and you can measure the a temperature at precisely the point you Po S want e g ceiling floor or in the middle of room Model ITS30J IMPORTANT NOTES e Do not insert the temperature sensor to the black 3 5mm jack which is input The temperature sensor will be damaged by 12V coming from this input e Do not insert or remove the temperature sensor on a running device Switch off the device before you insert or remove the temperature sensor e If the sensor shows 85C 127C or OC when the temperature is obviously different from these values it might be a sign that the sensor is not properly inserted or is damaged NOTE Check that the sensor is inserted into the 3 5mm red jack socket to the very end The connection is taught and you p have to ensure that there is no gap between the connector of the sensor and the jack socket Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 14 English iSocket Environment Pro www isocketworld com 7 1 Thermometer The external temperature sensor measures the temperature of the environment in the particular area where it is installed and iSocket can provide this information via SMS Information about the temperature can be available im
50. sensor s status is ALERT SMSCHANGE Conf SMSCHANGE changed logical value was changed OK ALERT CALL Notify by phone call to predefined numbers when the sensor ALERT CALL OK Conf is triggered It is just a call there is no any voice notification ALERT OFF Disable alerts This is useful if you want just to activate ALERT OFF OK Conf Micro relay when sensor was triggered ALERT Information about ALERT configuration ALERT SMS CALL Inf SMSCHANGE OFF NOTE Do not keep wrong or non existent numbers in the list of ALERTNUMBER This will delay alerts to good numbers 9 3 Input Output Relations The relay of the main power socket can be switched on or off for the time configured by command RELAYTIME when the sensor is triggered This allows you to activate external equipment according to your specific needs This feature is only available when Alarm Function is enabled Command Description Response Type RELAYTIME ONGO Turn on main power socket 60 seconds when sensor RELAYTIME ON60 Conf is activated Maximum value is 65000 seconds OK RELAYTIME ON Turn on main power socket permanently when RELAYTIME ON OK Conf sensor is activated RELAYTIME OFF60 Turn off main power socket 60 seconds when sensor RELAYTIME OFF60 Conf is activated Maximum value is 65000 seconds OK RELAYTIME OFF Turn off main power socket permanently when RELAYTIME OFF Con
51. sialsioteieialadedas 24 17 TROUDIESNOOUING visio ovas quus o pepe Dx Ep orsa xDD ERR caa a Diu Ra iuba S a aa 25 18 Limits of Warranty and Liability 1 25s5sa durius bu sias cibricka aerazczia c riePa egais 26 L9 CDDDdCES usine pSRazErirEruu EEEE EE URS EMI NAAR NA EUREN FRE 26 Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 2 English iSocket Environment Pro www isocketworld com 1 Device Description iSocket Environment Pro is designed for remote monitoring of the environment in your premises to give you peace of mind This intelligent socket is controlled remotely by SMS commands via the GSM network You can use either standard mobile phones old phones or smartphones to manage and configure iSocket It is also possible to carry out some operations by a phone call SIM cards from most GSM operators including prepaid cards can be installed in iSocket The following aspects of the environment can be monitored with iSocket e Power monitoring You will get an alert to your cell phone when the power fails or is restored to your system This is possible because the iSocket Environment Pro has a built in battery You do not need to buy any extra accessories to activate this feature e Temperature monitoring With a precision external sensor connected to iSocket you can measure the temperature of almost any element air water oil solid surfaces etc Information about temperature will be sent to
52. the plugs and sockets of other models fa Fe Pn Socket Plug Socket Plug Socket Plug BS 1363 NEMA 5 15 CEE 7 5 British North French America Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 8 Y X n Qe e i Socket Plug Socket Plug Socket Plug AS NZS 3112 SEV 1011 CEI 23 50 Australian Swiss S17 P17 Italian 4 Socket Plug SI32 Israeli English iSocket Environment Pro www isocketworld com 2 Safety Instructions This appliance complies with accepted technological standards with regard to safety Nevertheless as manufacturers we consider it our obligation to make you aware of the following safety information To ensure years of trouble free enjoyment and to maintain your guarantee please note the following oN O 3 Never carry out repairs yourself There are no serviceable parts in the device The operating voltage of the appliance and the mains voltage as well as the type of current must match see the rating plate on the underside of the appliance Only plug into a correctly installed earthed mains socket The device is not intended for direct plug in equipment which are not equipped with a plug External equipment that connects to the device must have a cord with appropriate plug Some devices are supplied with their own switch which needs to be disconnected before they are unplugged Do not use this product with such devices it cannot
53. the temperature for turning off SWITCHOFFTEMPZ10C 50F Conf the main socket when thermostat OK or enabled Values from 55C to 120C THERMOSTAT HEATING or from 67F to 248F Do not forget THERMOSTAT Disabled SWITCHOFFTEMP S50F to type C means Celsius or F means Fahrenheits after the value Only integer values must be used Please only use even numbers for Fahrenheit temperatures THERMOSTAT Information about thermostat THERMOSTAT Enabled Inf configuration THERMOSTAT HEATING Switch off temperature 10C 50F Do you particularly agree or disagree with anything in our software Give us your opinion http www isocketworld com feedback Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 15 English iSocket Environment Pro www isocketworld com Example of heating system control A typical example of temperature control would be heating activation in remote area if the temperature drops below 10C 50F The following settings must be used THERMOSTAT HEATING SWITCHOFFTEMP 10C or SWITCHOFFTEMP 50F THERMOSTATON With these settings the thermostat will keep the temperature in the range of about 10C 50F This means that as soon as the room is heated up to 10C 50F the main socket is turned off If the current temperature in the room is over 10C 50F the main socket does not turn on until the temperature drops below 10C 50F Example of cooling system control An
54. then the option RING goes into the value VOACTION automatically In response to the activating call the device will send you a message You can configure a call response instead of an SMS Read more about this in Chapter 6 2 The following table indicates which actions can be pre configured Command Description Response Type RING SWITCH Switching changing status to negative main power RING SWITCH OK Conf socket by phone call SECLIST is not active RING RESTART Restart return to the same status after a certain RING RESTART OK Conf period of time main socket by phone call Time for SECLIST is not active restart set by RESTARTTIME RING NOACTION Ignore phone calls RING NOACTION OK Conf RING Informs what action configured RING NOACTION Inf RESTART SWITCH Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 9 English iSocket Environment Pro www isocketworld com 4 3 Manual Managing The main power socket can be managed manually You can switch it manually by a hidden button which is on the front panel next to the logo The button can be activated with a suitable thin mechanic tool Pressing this button switches the main power socket to a negative value So if it was turned off it will be turned on and vice versa Would you like to see more features You are welcome to send us your feedback http www isocketworld com feedback 5 Security am
55. ting logic Only one alarm within 60 seconds is indicated This means that if two or more sensors were activated within one minute you will only get the one alert During the notification cycle the device will not detect new sensor triggering The device will be ready to detect sensor activity no later than one minute after completion of the notification cycle If the sensor is still active at this time the device will start a new session of notifications Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 19 English iSocket Environment Pro www isocketworld com For these reasons the alert by SMS or call is the ideal option for motion or vibration sensors which changes its logical O to logical 1 value and back to 0 In this case only one alert is generated and you receive a notification However this setting is not suitable for example for door smoke gas or water sensors which change their logical state from O to 1 and stay in this state Since they remain in this state you will receive endless alerts until you deactivate the Alarm Function For sensors that change their status and stay in that status the option SMSCHANGE was designed With this configuration you will be notified only once when a logical value is changed Command Description Response Type ALERT SMS Send SMS to predefined number when the sensor is triggered ALERT SMS OK ALERT Send SMS to predefined number when the
56. ught it Post warranty service is provided by the manufacturer or authorised service centres if such exist Some advice can be given by e mail When contacting sure to specify the device model and firmware version you can check this by sending the SMS commands FIRMWARE and HARDWARE to device Please read Chapter 15 for information about the indicators Indicators can signal different faults Possible malfunction No lights on indicators after iSocket switched into a wall outlet Possible solution Make sure that the wall outlet is functioning and that power is available Possible malfunction The device is plugged into a wall outlet the POWER indicator is on but the device does not accept any commands Possible solution Make sure that all indicators are correctly lit see Chapter 15 the SIM card is inserted correctly PIN code authorisation is removed on the SIM card and the GSM network is available Possible malfunction The device attached to the main socket will not turn on although the main socket itself is working Possible solution Check whether the connected device functions and whether its own switch is turned on Possible malfunction Command was sent but no response and nothing happens Possible solution The iSocket could have lost contact with the GSM network or there is no electricity in the home network If you re away from the device and cannot verify the existence of electricity in the home network or the GSM signal you c
57. volatile memory and are not lost when power is off Each configuration command has a default value This is the value that was installed at the factory for details see Chapter 14 2 Information commands marked Inf in the tables These commands inform you about different statuses of the device or about other corresponding statuses so they have information nature If a command has a question mark at the end COMMAND then this command will inform you about current value of the parameter which has the same name as the command These commands are available at any time Should a configuration command have different values these will all be seen in response to the information command associated with this configuration command The values will be comma separated and the current active value will be indicated in parentheses For example you send the information command COMMAND In response you will get the reply COMMAND VALUE1 VALUE2 This means that the current active value is VALUE2 and VALUE1 is another value acceptable for this command This syntax is made for your convenience you do not need to refer to the manual each time when to remember all possible values They will be given in the response The first value in the response is the factory default value see Chapter 14 3 Control and management commands marked Ctrl in the tables Used to control the iSocket device perform some active action They are not limited by co
58. which it is supplied The license is non transferable and you do not have the rights to grant sublicenses e Your iSocket device has a unique feature iSocket Online 24 7 that gets the device back online even after a break in the GSM network However the device needs a strong GSM signal in the area it has an internal antenna and may not operate efficiently if the signal in your area is weak Ensure that you have a strong GSM network before using the device Do not put metal or other conductive objects near the device this may cause signal loss This product is designed for home and office use only e Different types of alerts that iSocket send you power failure power restored temperature rise temperature fall sensor triggered etc rely on the correct configuration of the mobile phone number for the alerts see Chapter 5 3 e This product uses a Lithium ion battery and MUST NOT be used outside the specified temperature Please refer to technical information Chapter 16 for detailed information about operating conditions and read the safety instruction Chapter 2 carefully e If you wish to use the iSocket Power Notifier feature plug in the device for 10 hours before use This will charge the built in battery e If you use a prepaid card you might be need to activate it first with your cell phone network provider More information is available from wwwW isocketworld com prepaid iSocket Environment Pro www isocket
59. world com Content or rr T 2 L Device Descriptio eseas sosea aaa a aa aa a a E a aa KE ba aa 3 2 Safety INSEPUCIIONNS sieisen a a a a a iei 5 By QUICK St l e aA a AAAA A AEAN ENAN 7 4 Managing the iSocket Device s ssssssssssssrrrsnrrrrossssssannnnnnnnrrrosssssnannnnnnnnrrrenssnnnnn 8 4 1 Managing by SNIS iei c PIE Er uM DE E nM RM EIE E EE ES 8 4 2 Managing by Phone C alllacicccnudieabcnedscatuncdunatenedusahdnaiace desedunahummdareddsedacedwendaue 9 4 9 Marital ManagiN gesseren oinei ioe a ipio ia ol spp eif 10 5 Security amp Notifications SettingS uos odiis drbae ups d bru Doo bl vada pd vade bd uid iv v Dros but uds 10 5 1 Security Numbers List Settings iiiiiixssciv sas E Su xax SRRXRORXAFPAYRERERRIERAXSRRXGDR XS EAE 10 5 2 Password Protection 52223 Paese EP Ere FI Pu M Sax M FEDES E IE 11 5 3 Configuration of the Numbers for Alerts sssessseeeseen nmn 11 5 Command CONMMMAUOM 5acisusasiuiRkre ScERERRRRRARAIERKPIEGEERIF ERU ERI MR AREE RIE RENE RENE AE 12 6 1 Confirmation or SMS COMMANGS se iososoubitssatur big sione oxpibs bie ppitesbao spxpcbbspins bibis 12 6 2 Confirmation for Phone Calls 555 53x 328 aux SEREXRREXRSRX XIRYSRXERASERZN ERR RXDRRKEEENKE 12 6 3 Incorrect Commands Later Configuration and Commands From Unauthorised b M e 13 7 Measurement and Control of Temperature ssessssesssseeen enne 14 FAM Thermo
60. y cause a fire e In the event of incorrect use fluid may escape from the battery Avoid contact with this fluid If you touch it by mistake rinse the affected area with water If you get the fluid in your eyes seek medical advice Stop using the device if fluid is coming from it e Li ion batteries are subject to a natural ageing process The battery must absolutely be replaced when its capacity falls just 80 from the capacity as new A weak old battery is no longer capable of meeting the high power requirements and therefore poses a safety risk e Exhaustive discharge will damage the battery The most common cause of exhaustive discharge is lengthy storage or non use of a partly discharged battery Don t allow the device to be stored for a long time without use Never use a battery driven device if you suspect that the last time the battery was charged was more than 12 months ago There is a high probability that the battery has already suffered dangerous damage exhaustive discharge Rechargeable batteries contain materials that are potentially harmful to the ex environment Batteries may not be disposed of with normal domestic waste You should dispose of used batteries at your local collection point Copyright iSocket Systems 2015 All rights reserved Version 1 0 1 EN 6 English iSocket Environment Pro www isocketworld com 3 Quick Start Quick Start comprises three simple steps Step 1 Install SIM card You need a
61. your cell phone iSocket will notify you when the temperature rises beyond or falls below specified levels iSocket has a thermostat that turns equipment on and off according to your settings Unique features of iSocket Smart Software will allow you to create an advanced temperature monitoring system e Security and safety monitoring With a motion and or door opening sensor connected to the input of iSocket Environment Pro you can create a simple home alarm system in a few minutes An alert about a break in will be sent to your cell phone immediately You may connect various logical sensors to the input of the iSocket to monitor the safety environment to detect e g smoke fire water leaks or gas leakage The alert will be sent to your cell phone when something happens We manufacture pre wired sensor sets for simple installation You do not need specific skills to configure these features Please see Chapter 9 for more information Remote switching and reboot And of course iSocket supports remote switching and reboot of equipment connected to it You will definitely appreciate the elegant design of iSocket with plugs and sockets suitable for many countries No service fee We do not charge you monthly fees You pay for the equipment once up front and then you are free to choose subscriptions from your favourite GSM mobile operator or to use prepaid Pay As You Go cards Free of charge operations Some operations e g remote switching or re

iSocket Environment Pro (EN)

Contents

Download Pdf Manuals

Related Search

Related Contents