Dual Rail LCD PS/2 - USB Console RM-KB
Contents
1. Chapter 3 Operation 4 Reach underneath and pull the keyboard module all the way out until it clicks into place Opening Together Refer to the diagrams in the Opening Separately section as you do the following 1 Pull the release catch and pull the top and bottom panels out until the keyboard module clicks into place Note Once the console has been released you can let go of the catch 2 Pull the top panel the rest of the way out until it clicks into place 3 Rotate the top panel all the way back to expose the LCD screen Note Refer to the warning regarding placing excessive weight on the keyboard module on the following page RM KB LCD 17 User Manual Operating Precautions The maximum load bearing capacity of the keyboard module is 30kg Failure to heed the information below can result in damage to the keyboard module RIGHT Rest your hands and arms lightly on the keyboard module as you work WRONG DO NOT lean your body weight on the keyboard module DO NOT place heavy objects on the keyboard module 18 Chapter 3 Operation Closing the Console 1 Pull the release catches located on either side of the keyboard toward you to release the keyboard module then slide the module slightly in 2 Let go of the catches Using the2. 1 Slide the Firmware Upgrade Recovery Switch see page 6 to the Normal position 2 Power off and restart the RM KB LCD17 according to the instructions given in the Powering Off and Restarting section see page 21 30 Appendix Safety Instructions General Read all of these instructions Save them for future reference Follow all warnings and instructions marked on the device Do not place the device on any unstable surface cart stand table etc If the device falls serious damage will result Do not use the device near water Do not place the device near or over radiators or heat registers The device cabinet is provided with slots and openings to allow for adequate ventilation To ensure reliable operation and to protect against overheating these openings must never be blocked or covered The device should never be placed on a soft surface bed sofa rug etc as this will block its ventilation openings Likewise the device should not be placed in a built in enclosure unless adequate ventilation has been provided Never spill liquid of any kind on the device Unplug the device from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning The device should be operated from the type of power source indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company The device is des
3. After a device is inserted into the rack carefully extend the rail into a locking position and then slide the device into the rack Do not overload the AC supply branch circuit that provides power to the rack The total rack load should not exceed 80 percent of the branch circuit rating Ensure that proper airflow is provided to devices in the rack Do not step on or stand on any device when servicing other devices in a rack Technical Support Technical support is available both by email and online with a browser over the web TechSupport middleatlantic com Phone 973 839 1011 When you contact us please have the following information ready beforehand Product model number serial number and date of purchase Your computer configuration including operating system revision level expansion cards and software Any error messages displayed at the time the error occurred The sequence of operations that led up to the error Any other information you feel may be of help 33 RM KB LCD17 User Manual Specifications Function RM KB LCD17 Computer Connections 1 Console Selection Hotkey Console Ports External Keyboard 1 x 6 pin Mini DIN Female Purple 1 x USB Type A Female Black Connectors Video 1 x HDB 15 Female Blue Mouse 1 x 6 pin Mini DIN Female Green 1 x USB Type A Female Black KVM Ports 1 x SPHD 18 Female Yellow External Mouse 1 x USB Type
4. devices on the RM KB LCD 17 installation Changes may have been made to the manual since it was put on the CD Please visit our web site at www middleatlantic com to download the most up to date version of the manual RM KB LCD 17 User Manual Contents FCCInformation xa k an DERA a J l n k dak ii User Notice ocios pestle deal Seer keira eaten hoe a gra iii Package ContentS kK cece KK KK KK KK KK KK eee eee iv About This Manual aa Xa rara raja Beale d ka vii QOV6IV W cnica Ed a e l 4 el a E A Ke ee vii GCONVENTIONS aii tdt khe nk Hehe ee tcp viii Chapter 1 Introduction OVENVICW sere Firth nt ate ale ote oath foe wei in y D az 1 a Hm Doe hm we eo tee eed 2 Requirements Ser apa r n 3 LGD Consoles cnn ewa disk Ma Win A GIR nan Ay QEW uk s 3 External Console WW kk kk cece cette KI KK KK KK 3 Operating Systems i kk kk kk kK KK KK KK KK KK KK KK KK KK ee 3 Component srice i id A Vee a e 4 Front VIEW A eth ees Su wi ee 4 Keyboard Module 0 0 ka k kk eee 5 EGDM QUIS swine cee oie anda ewok ene atin y Satna Hen h asa 6 Rear Vi w sacs xanan ie eee Pee HOS ae Es 7 Chapter 2 Hardware Setup Before you Begin 2 2 2 0 kk kak kk kk kk kK kk kk kk kk kk eee 9 Rack Mounting perri pasa 5k dk A a ak kl aa AJA AA cele A nA Da W eke 10 Connecting Ups s as bee la A e e ke E an ee eke atta fi 13 Chapter 3
5. A Female Black FW Upgrade 1 x RJ 11 Power 1 x 3 prong AC Socket Switches Reset 1 x Semi recessed Pushbutton Power 1 x Rocker F W Upgrade 1 x Slide LCD Power 1 x Pushbutton LCD Adjustment 4 x Pushbutton LEDs Power 1 Blue LCD Power 1 Orange Lock Num 1 Green Caps 1 Green Scroll 1 Green Emulation Keyboard Mouse PS 2 USB Video 1280 x 1024 75Hz DDC2B I P Rating 100 240VAC 50 60Hz 1A Power Consumption 29 6W Environment Operating Temp 32 104 F 0 40 C Storage Temp 4 140 F 20 60 C Humidity 0 90 RH NC Physical Housing Metal amp Plastic Properties gt Weight 35 05 Ibs 15 90 kg Dimensions L x W x H 22 76 in x 18 98 in x 1 73 in 578mm x 482 7mm x 44mm 34 Appendix Sun Keyboard Emulation The PC compatible 101 104 key keyboard can emulate the functions of the Sun keyboard when the Control key Ctrl is used in conjunction with other keys The corresponding functions are shown in the table below PC Keyboard Sun Keyboard Ctrl T Stop Ctrl F2 Again Ctrl F3 Props Ctrl F4 Undo Ctrl F5 Front Ctrl F6 Copy Ctrl F7 Open Ctrl F8 Paste Ctrl F9 Find Ctrl F10 Cut Ctrl 1 m Ctrl 2 O mq Ctrl 3 Q mg Ctrl 4 C Ctrl H Help E Compose as Note When using key c
6. Num Lock Caps Lock and Scroll Lock LEDs will continually flash on and off To exit the Firmware Upgrade Mode see Exiting Firmware Upgrade Mode page 30 26 Chapter 4 Firmware Upgrade Performing the Upgrade Starting the Upgrade 1 With the RM KB LCD17 in Firmware Upgrade Mode run the downloaded Firmware Upgrade Package file from your computer either by double clicking the file icon or by opening a command line and keying in the full path and filename The Firmware Upgrade Utility main screen appears 25 Firmware Upgrade Utility xi If Check Firmware Version is checked the utility compares the device s firmware level with the upgrade files If the device s version is newer the utility lets you decide whether to continue or not If it is not checked the utility performs the upgrade directly Click Next to begin Device List Status Messages le gt Loading amp testing fil testing fi gt Loading amp te Searching fo les les Device Description IV Check Firmware Version Progress Help View Log The Utility inspects your installation All the devices capable of being upgraded by the package are listed in the Device List panel 27 RM KB LCD17 User Manual 2 Click Next to perform the upgrade Ifyou enabled Check Firmware Version the Utility compares the device s firmware level with that of the upgrade files If it finds that t
7. Operation Opening the Console 0 0 0 kK KK KK tte 15 Opening Separately 0 0 0 0 cece eee 15 Opening Togethers sa ii redie aa aa Aa eee 17 Operating Precautions s asuaan aaee 18 Closing the Console kk kk kK KK KK KK KK KK KI KK KK KK KK IK KK 19 HotPlt qingi tie ceed a E Kake wide ee U alan a kad wl S ra 21 Powering Off and Restarting 00 00 kK KK KK KK KK KK KK 21 LCD OSD Configuration 0 0 0 KK KK KK KK KK KK KK KI KK KK KK 22 The LGD Buttons ocio nta o Bar dee anne creda oan lara 22 LCD Adjustment Settings kk kk KK KK KK KK KK KK KK KK KK 23 Console Selection 0 0 0 cece KK KK KK KK KK KK K KK 24 RM KB LCD 17 User Manual Chapter 4 Firmware Upgrade The Firmware Upgrade Utility oooooooooooooo o 25 Before You Begin i kk kk kak kk kk kk kK eee 25 Firmware Upgrade Mode WWW kk kK KK KK KK KK KK KK eee 26 Performing the Upgrade uk kk kk eee eee eee 27 Upgrade Failed WA kk kk kk kk KEK KIR KIR eee 29 Firmware Upgrade Recovery ooococcccoco KK KK KK KK KI KK 30 Exiting Firmware Upgrade Mode kk KK KK eee eee KK 30 Appendix Safety Instructions 45 53 i 4 532451344 a a 2d in Dad D r d n 31 CA RR RrRr en 31 Rack Mounting crre una a a zal wd poi w ak aw Wl Al a aa ia alal 33 Technical Support 2 0 0 0 ay a a D aa bela ae re a eee 33 Specifications A4 4 a a de AS Y 34 Sun Key
8. Upgrade Recovery Switch see page 26 is in the Normal position Ctrl Alt Shift L Enter Enable Local LCD console Disable Remote external console Ctrl Alt Shift R Enter Enable Remote external console Disable Local LCD console Ctrl Alt Shift L R Enter or Enable both consoles default Ctrl Alt Shift R L Enter Note 1 Press the keys in sequence one key at a time First Ctrl then Alt then Shift etc 2 Console selections are not saved If the RM KB LCD 17 is powered off it reverts to the default setting of both consoles enabled when it is powered on again 3 If the KVM switch connected to the RM KB LCD 17 uses the Ctrl Alt Shift combination to invoke its hotkey mode you won t be able to access any of its hotkey operations because the RM KB LCD 17 will capture the combination for console selection first 24 Chapter 4 Firmware Upgrade The Firmware Upgrade Utility As new firmware revisions become available for the RM KB LCD17 firmware upgrade packages are posted on our web site The Windows based Firmware Upgrade Utility FWUpgrade exe provides a smooth automated process for upgrading the RM KB LCD17 s firmware Check the web site regularly to find the latest firmware packages and information relating to them Before You Begin To prepare for the firmware upgrade do the following 1 From a computer that is not part of your RM
9. in a 1U high system rack Easy Installation Rack Mount Kit single person installation included Supports an external console with either PS 2 or USB connectors Dual interface Supports computers and KVM switches with PS 2 or USB keyboards and mice Additional hot pluggable USB mouse port on front panel Internal power supply High video resolution Upto 1280 x 1024 75Hz Supports DDC DDC2 DDC2B DDC emulation of the LCD monitor Video settings of attached computers are automatically adjusted for optimal output to the LCD monitor Standard 105 key keyboard Sun keyboard emulation Dual rail design allows LCD monitor and keyboard touch pad modules to operate independently Adjustable depth to fit within the rack Firmware upgradeable Supports Microsoft Intellimouse 5 keys Supports Logitech and Microsoft wireless mice Locking mechanism to securely lock the keyboard drawer in the open position DDC emulation video settings of each computer are automatically adjusted for optimal output to the monitor Chapter 1 Introduction Requirements LCD Console The LCD console supports most KVM switches that have PS 2 and USB console port connectors If you are unsure whether your switch is supported or not check with Middle Atlantic The integrated LCD monitor s maximum resolution is 1280 x 1024 75Hz Make sure that none of the resolution settings of the connected computers exceed
10. only the monitor is off not the KVM switch itself 4 Firmware The Firmware Upgrade Cable that transfers the firmware Upgrade Port upgrade data from the administrator s computer to the RM KB LCD17 plugs into this RJ 11 connector 5 Firmware During normal operation and while performing a firmware Upgrade Switch upgrade this switch should be in the NORMAL position If a firmware upgrade operation does not complete successfully this switch is used to perform a firmware upgrade recovery See Firmware Upgrade Recovery page 30 for details Chapter 1 Introduction Rear View 1 2 3 4 gt Eb No Component Description 1 Power Socket This is a standard 3 prong AC power socket The power cord from an AC source plugs in here 2 Power Switch This is a standard rocker switch that powers the RM KB LCD17 on and off 3 External For flexibility and convenience the RM KB LCD17 supports Console Section an independent external LCD Console The external console s keyboard monitor and mouse cables plug in here 4 KVM Port The cable linking the RM KB LCD17 to a computer or switch Section plugs in here Note The shape of this SPHD connector has been specifically modified so that only KVM cables designed to work with this console can plug in see External Console page 3 for details Do NOT attempt to use ordinary 15 pin VGA connector cable to link this
11. the LCD monitor s maximum resolution External Console A VGA SVGA or MultiSync monitor capable of displaying the highest resolution provided by any computer in the installation USB or PS 2 keyboard and mouse Operating Systems Supported operating systems are shown in the table below OS Version Windows NT and higher Linux RedHat 7 1 and higher SuSE 9 0 and higher Mandriva Mandrake 9 0 and higher UNIX AIX 4 3 and higher FreeBSD 4 2 and higher Sun Solaris 8 and higher Novell Netware 5 0 and higher DOS 6 2 and higher RM KB LCD17 User Manual Componenits Front View No Component Description 1 Upper Handle Pull to slide the LCD module out push to slide the module in See Opening the Console page 15 for details on sliding the console in and out 2 LCD Module See LCD Module page 6 Keyboard Module See Keyboard Module page 5 4 Lower Handle Pull to slide the keyboard module out See Opening the Console page 15 for more details on sliding the console in and out 5 Power LED Lights blue to indicate that the unit is receiving power 6 LCD Release These catches one on each side release the LCD module Catch so you can slide it away 7 Rack Mounting Tabs The rack mounting tabs located at each corner of the unit secure the chassis to a system rack See Rack Mounting page 10 for details Chap
12. Dual Rail LCD PS 2 USB Console RM KB LCD 17 User Manual o Middle Atlantic Products Phone 973 839 1011 www middleatlantic com 1 00386 1 Rev B RM KB LCD 17 User Manual FCC Information This is an FCC Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense RoHS This product is RoHS compliant Ze Intertek RM KB LCD 17 User Manual User Notice All information documentation and specifications contained in this manual are subject to change without prior notification by the manufacturer The manufacturer makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties as to merchanta
13. KB LCD17 installation go to our Internet support site and choose the model name that relates to your device to get a list of available Firmware Upgrade Packages 2 Choose the Firmware Upgrade Package you want to install usually the most recent and download it to your computer 3 Use the Firmware Upgrade Cable provided with this unit to connect a COM port on your computer to the Firmware Upgrade Port of the RM KB LCD17 E AN Vis BE E OEEO ENO EBRO E GER CARRERO HIE K 2 2 J 25 RM KB LCD17 User Manual Firmware Upgrade Mode The RM KB LCD17 s firmware upgrade mode can be accessed one of two ways by entering a hotkey sequence see Console Selection page 24 or by placing the RM KB LCD17 in firmware upgrade recovery mode see Firmware Upgrade Recovery page 30 Note In order to activate the Firmware Upgrade Mode using a hotkey sequence the Firmware Upgrade Recovery Switch see page 6 must be set to the Normal position 1 Turn off the power to the RM KB LCD17 using the power switch located on the back side of the console 2 Slide the firmware switch to RECOVER see page 6 3 Turn on the power to the RM KB LCD17 using the power switch located on the back side of the console When the RM KB LCD 17 is in Firmware Upgrade Mode the
14. KVM cable into their respective ports on a computer If you are installing an external console plug your keyboard monitor and mouse into their respective ports on the Console Section of the LCD Console The ports are color coded and marked with an icon for easy identification Plug the power cord into the AC power socket of the RM KB LCD17 and the other end into the AC power source Turn on the computer Turn on the power to the RM KB LCD17 Installation Diagram RM KB LCD17 User Manual This Page Intentionally Left Blank Chapter 3 Operation Opening the Console The RM KB LCD 17 s console consists of two modules an LCD display module located under the top cover and a keyboard touch pad module below the LCD module The modules can either slide together or independently This allows you to have the LCD display available for viewing while the keyboard touch pad module is conveniently out of the way when not in use Opening Separately 1 Pull the top panel a few centimeters toward you SAP Continues on next page RM KB LCD 17 User Manual Continued from previous page 2 Pull the top panel all the way out until it clicks into place QS
15. apter 4 Firmware Upgrade Upgrade Failed If the upgrade failed to complete successfully the Upgrade Failed screen appears 25 Firmware Upgrade Utility xl The Firmware upgrade failed Click Cancel to close the utility then try again Device List Status Messages gt Loading amp testing files gt Loading amp testing files OK gt No device attached to the serial Firmware upgrade failed Device Description IV Check Firmware Version Progress lt Back Finish Cancel Click Cancel to close the Firmware Upgrade Utility See the next section Firmware Upgrade Recovery for how to proceed 29 RM KB LCD17 User Manual Firmware Upgrade Recovery There are basically three conditions that call for firmware upgrade recovery When the unit s firmware becomes corrupted for some reason and you are unable to operate it When a firmware upgrade procedure is interrupted When a firmware upgrade procedure fails To perform a firmware upgrade recovery do the following 1 Slide the Firmware Upgrade Recovery Switch see page 6 to the Recover position 2 Power off and restart the RM KB LCD17 according to the instructions given in the Powering Off and Restarting section see page 21 3 Slide the Firmware Upgrade Recovery Switch back to the Normal position 4 Repeat Step 2 Exiting Firmware Upgrade Mode To exit the Firmware Upgrade Mode do the following
16. ation ii Rear View 7 Features 2 Rear View DC Power 8 Firmware upgrade Restarting 21 cable 25 RoHS ii Mode 26 recovery 30 S utility 25 Safety Instructions Front View 4 General 31 Rack Mounting 33 H Specifications Hot Plugging 21 AC Power Model 34 SPHD Connectors 36 K System Requirements Keyboard Emulation External Console 3 Sun 35 LCD Console 3 Keyboard Module 5 Operating Systems 3 L T LCD Technical Support 33 Adjustment Settings 23 Troubleshooting 36 Buttons 22 OSD configuration 22 U LCD Module 6 User Notice iii 37
17. bility or fitness for any particular purpose Any of the manufacturer s software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not the manufacturer its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software The manufacturer of this system is not responsible for any radio and or TV interference caused by unauthorized modifications to this device It is the responsibility of the user to correct such interference The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE RM KB LCD 17 User Manual Package Contents The RM KB LCD 17 package consists of 1 RM KB LCD 17 Dual Rail LCD PS 2 USB Console 1 Single Installation Set 1 Hybrid KVM Cable 6 feet 1 8m 1 Power Cord 1 Firmware Upgrade Cable 1 User Manual Soft copy in CD 1 Quick Start Guide Soft copy in CD Check to make sure that all of the components are present and in good order If anything is missing or was damaged in shipping contact your dealer Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the console or to any other
18. board Emulation kk kK KK KK KK KK KK KK KK KK KK gt 35 Troubleshooting merci keka it Sa Ak nA DAY nS AA 36 About SPHD Connectors kk kK kK KK KK KK KK KK KK KK KK KK K 36 vi RM KB LCD 17 User Manual About This Manual This User Manual is provided to help you get the most from your RM KB LCD 17 system It covers all aspects of installation configuration and operation An overview of the information found in the manual is provided below Overview Chapter 1 Introduction introduces you to the RM KB LCD 17 KVM Console Its purpose features and benefits are presented and its components are described Chapter 2 Hardware Setup provides step by step instructions for setting up your installation and explains some basic operation procedures Chapter 3 Operation describes the fundamental concepts involved in operating the RM KB LCD 17 Chapter 4 Firmware Upgrade explains how to upgrade the RM KB LCD 17 s firmware with the latest available versions An Appendix provides specifications and other technical information regarding the RM KB LCD 17 vii RM KB LCD 17 User Manual Conventions This manual uses the following conventions Monospaced 1 Indicates text that you should key in Indicates keys you should press For example Enter means to press the Enter key lf keys need to be chorded they appear together in the same bracket with a plus sign between them Ctrl Alt Number
19. choice with the navigation buttons pressing this button brings up its adjustment screen gt ja When navigating through the menus this button moves you Right or Up When making an adjustment it increases the value dy When navigating through the menus this button moves you Left or Down When making an adjustment it decreases the value EXIT When you have not entered the LCD OSD Menu function pressing this button performs an auto adjustment An auto adjustment automatically configures all the settings for the LCD panel to what the OSD considers their optimum values to be When you have entered the LCD OSD Menu function pressing this button exits the current menu and returns you to the previous menu Use it to leave an adjustment menu when you are satisfied with the adjustment you made When you are at the Main Menu pressing this button exits the LCD OSD 22 Chapter 3 Operation LCD Adjustment Settings An explanation of the LCD OSD adjustment settings is given in the table below Setting Explanation Brightness Adjusts the background black level of the screen image Contrast Adjusts the foreground white level of the screen image Phase If pixel jitter or horizontal line noise is visible on the display your LCD may have the wrong phase setting Adjust the phase setting to eliminate these problems Clock If vertical banding is visible on the display your LCD ma
20. d with this package to loosely attach the front of the RM KB LCD17 to the front of the rack only tighten the screws part way Phillips head M4L6 RM KB LCD17 User Manual 3 Slide the rear attachment sliding brackets along the slide bars until they contact the rear of the RM KB LCD17 then use the bracket screws supplied with this package to attach the bars to the rear of the RM KB LCD17 tighten the screws all the way Phillips head M4L6 1909500505008 Y sz o po DDE oe el t DED DE ZE DE U TE E TE E 4 Slide the RM KB LCD17 open and closed a couple of times to be sure that it is properly aligned and operating smoothly See Opening the Console page 15 for opening and closing procedures 5 After determining that the RM KB LCD17 is lined up and operating correctly finish by fully tightening the front attached bracket screws inserted in Step 2 Note Allow at least 2 inches 5 cm on each side for proper ventilation and at least 5 inches 12 5 cm at the back for the power cord and cable clearance Chapter 2 Hardware Setup Connecting Up Refer to the example installation diagram as you perform the following steps 1 Plug the SPHD connector end of a KVM cable either supplied with the unit or purchased separately see External Console page 3 into the LCD Console s KVM port Plug the keyboard monitor and mouse connectors of the
21. ed lists represent procedures with sequential steps Bullet lists provide information but do not involve sequential steps Indicates selecting the option on a menu or dialog box for example that comes next For example Start Run means to open the Start menu and then select Run Indicates critical information viii Chapter 1 Introduction Overview The RM KB LCD17 is a LCD Console module featuring an integrated 17 LCD panel a full keyboard and a touch pad in a 1U rack mountable sliding housing with an AC based power input source The RM KB LCD17 s LCD and keyboard touch pad modules slide independently of each other To maximize space in your data center the keyboard touch pad module slides back to hide away when not in use while the thin profile LCD monitor rotates back flush against the rack allowing convenient monitoring of computer activity For added convenience ports for an external PS 2 or USB keyboard and mouse as well as a monitor are provided on the rear panel permitting you to manage the switch from a local console up to 20 meters away Since the RM KB LCD17 s firmware is upgradable you can stay current with the latest functionality improvements simply by downloading firmware updates from our web site as they become available RM KB LCD17 User Manual Features Integrated LCD Console with 17 LCD monitor in a dual rail housing with top and bottom clearance for smooth operation
22. front handle push the keyboard module all the way in Continues on next page 19 RM KB LCD 17 User Manual Continued from previous page 3 Rotate the LCD module all the way down then pull the rear catches to release the LCD module 2 EEE DE EDED z p po DE r ZEDE DD DD D D os t DD T 20 Chapter 3 Operation Hot Plugging The RM KB LCD 17 supports hot plugging components can be removed and added to the console by unplugging their cables from the ports without the need to shut down the RM KB LCD 17 Powering Off and Restarting If 1t becomes necessary to Power Off the RM KB LCD 17 to upgrade the firmware for example simply turn off the power to the unit using the rear panel power switch Restarting the RM KB LCD 17 is as easy as turning the rear panel power switch back on 21 RM KB LCD 17 User Manual LCD OSD Configuration The LCD Buttons The LCD OSD allows you to set up and configure the LCD display Four buttons are used to perform the configuration as described in the table below Button Function MENU When you have not entered the LCD OSD Menu function pressing this button invokes the Menu function and brings up the Main Menu When you have entered the LCD OSD Menu function and have reached a setting
23. he device s version is higher than the upgrade version it brings up a dialog box informing you of the situation and gives you the option to continue the upgrade A A 9 The firmware Ver 1 0 071 is not newer than current Firmware Ver 1 0 081 y in device MAIN 001 001 Continue the upgrade Yes No If you didn t enable Check Firmware Version the Utility installs the upgrade files without checking whether they are a higher level or not As the Upgrade proceeds status messages appear in the Status Messages panel and the progress toward completion is shown on the Progress bar Upgrade Succeeded After the upgrade has completed a screen appears to inform you that the procedure was successful 25 Firmware Upgrade Utility x The Firmware upgrade was successful Click Finish to close the utility Device List Status Messages DEA gt Loading amp testing files gt Loading amp testing files OK gt Searching for devices gt Preparing firmware upgrade gt Preparing firmware upgrade OK gt Upgrading device MAIN 001 001 gt Upgrading device MAIN 001 001 OK gt Upgrading device KB 001 002 gt Upgrading device KB 001 002 OK Device Description Device FAW Ver 1 1 101 Upgrade FAW Ver 1 0 071 MID 001 002 IM Check Firmw ersion Progress f Help View Log Back Cancel Click Finish to close the Firmware Upgrade Utility 28 Ch
24. igned for IT power distribution systems with 230V phase to phase voltage The device is equipped with a 3 wire grounding type plug This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not attempt to defeat the purpose of the grounding type plug Always follow your local national wiring codes Do not allow anything to rest on the power cord or cables Route the power cord and cables so that they cannot be stepped on or tripped over Continues on next page 31 RM KB LCD17 User Manual Continued from previous page If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes To help protect your system from sudden transient increases and decreases in electrical power use a surge suppressor line conditioner or uninterruptible power supply UPS Position system cables and power cables carefully Be sure that nothing rests on any cables Never push objects of any kind into or through cabinet slots They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock Do not attempt to service the device yourself Refer all servicing to qualified service personnel If the followi
25. ng conditions occur unplug the device from the wall outlet and bring it to qualified service personnel for repair The power cord or plug has become damaged or frayed Liquid has been spilled into the device The device has been exposed to rain or water The device has been dropped or the cabinet has been damaged The device exhibits a distinct change in performance indicating a need for service The device does not operate normally when the operating instructions are followed Only adjust those controls that are covered in the operating instructions Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair Do not connect the RJ 11 connector marked UPGRADE to a public telecommunication network 32 Appendix Rack Mounting Before working on the rack make sure that the stabilizers are secured to the rack extended to the floor and that the full weight of the rack rests on the floor Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack Always load the rack from the bottom up and load the heaviest item in the rack first Make sure that the rack is level and stable before extending a device from the rack Use caution when pressing the device rail release latches and sliding a device into or out of a rack the slide rails can pinch your fingers
26. ombinations press and release the first key Ctrl then press and release the activation key 35 RM KB LCD17 User Manual Troubleshooting Symptom Action There are ghost images on the external monitor Some characters enter from the keyboard do not display correctly can t use the special keys on the Sun external keyboard to control Sun computers The distance between the external console and the RM KB LCD17 is too great The maximum VGA cable distance should not exceed 65 62 feet 20 m and in some cases may need to be shorter Replace the VGA cable with one of an appropriately short length The keyboard layout setting for the port does not match the keyboard you are using On your switch change the keyboard layout setting for the port to match the layout of the keyboard you are using Use Sun keyboard emulation keystrokes page 35 to achieve all Sun keyboard functions About SPHD Connectors This product uses SPHD connectors for its KVM and or Console ports We have specifically modified the shape of these connectors so that only KVM cables that we have designed to work with this product can be connected 36 Index C O Closing the Console 19 Opening the Console 15 Connecting Up 13 Operating Precautions 18 Console Closing 19 P Opening Separately 15 Package Contents iv Opening Together 17 Powering Off 21 Console Selection 24 R F Rack Mounting 10 FCC Inform
27. port to a computer or switch RM KB LCD17 User Manual This Page Intentionally Left Blank Chapter 2 Hardware Setup Before you Begin A Important safety information regarding the placement of this device is provided on page 31 Please review it before proceeding Make sure that power to all the devices you will be connecting up has been turned off You must unplug the power cords of any computers that have the Keyboard Power On function Packing material has been inserted to protect the RM KB LCD17 during shipping Slide the LCD module out see Opening the Console page 15 until the packing material is visible Remove the packing material before installing the unit as shown in the diagram below RM KB LCD17 User Manual Rack Mounting To rack mount the RM KB LCD17 do the following 1 Attach the left and right mounting rails to the inside of the rack with the rackmount screws provided The flange that supports the RM KB LCD17 will be to the inside Rear Flange Slide Bar Front Flange Rear Attachment Sliding Bracket LEFT Support RAIL Flange Chapter 2 Hardware Setup a Screw the front flanges to the rack first b Slide the bars with the rear flanges toward the rack until the flanges make contact with the rack then screw the rear flanges to the rack HP 10 32 thread inch 2 Slide the RM KB LCD17 onto the support flanges Use the bracket screws supplie
28. ter 1 Introduction Keyboard Module No Component Description 1 Keyboard Release Catch These catches one on each side release the keyboard module so you can slide it away 2 Reset Button Pressing and holding this button while powering on the unit causes the RM KB LCD17 to revert to the original factory installed firmware version allowing you to recover from a failed firmware upgrade Pressing and holding this button for more than three seconds performs a system reset Note The button is recessed and must be pushed with a thin object such as the end of a paper clip or a ballpoint pen 3 Lock LEDs The Num Lock Caps Lock Scroll Lock LEDs are located here 4 Keyboard Standard 105 key keyboard Touch pad Standard mouse touch pad 6 External Mouse Port This USB mouse port is provided for users who prefer to use an external mouse RM KB LCD17 User Manual LCD Module No Component Description 1 LCD Display To access the LCD monitor slide the LCD module out and flip up the cover See Opening the Console page 15 for details on sliding the LCD module out 2 LCD Controls These buttons control the position and picture settings of the LCD display See LCD OSD Configuration page 22 for details 3 LCD On Off Push this button to turn the LCD monitor on and off The Button button lights when the LCD monitor is off to indicate that
29. y have the wrong clock setting Adjust the clock setting to eliminate vertical banding H Position Positions the display area on the LCD panel horizontally moves the display area left or right V Position Positions the display area on the LCD panel vertically moves the display area up or down Color Temperature Adjusts the color quality of the display You can adjust the warmth value color balance etc The Adjust Color selection has a further submenu that lets you fine tune the RGB values Language Selects the language that the OSD displays its menus in OSD Duration Lets you set the amount of time the OSD displays on the screen If there is no input for the amount of time you choose the OSD display turns off Reset Resets the adjustments on all menus and submenus to their factory default settings Note The Language setting does not return to the factory default but remains at the one that you have set it to 23 RM KB LCD 17 User Manual Console Selection Console selection on the RM KB LCD 17 is accomplished with hotkey combinations as described in the following table Combination Action Ctrl Alt Shift P C Enter to select normal mode pc etc Ctrl Alt Shift S U N Enter to select SUN Ctrl Alt Shift Activates the Firmware Upgrade Mode u p g r a d e Enter Note this Hotkey sequence only works when the Firmware
Download Pdf Manuals
Related Search