ELR10 Manual - Elektra Underfloor Heating
Contents
1. 3 INSTALLING THE FLOOR SENSOR The floor sensor must be installed in a blinded installation pipe e g a flexible PVC pipe which should be positioned in the upper layer of the floor concrete between heating cables The sensor wire can be extended up to 50m of length Plaster box ny Temperature controller s Temperature sensor wire Protection pipe e g PVC Temperature sensor even distance between heating cables Plug Floor Heating mat Tile cement Sand concrete mortar Insulation Ceiling Fig 3 Installing the floor temperature sensor with Elektra heating mats used ELEKTRA 4 INSTALLING THE CONTROLLER WITH BUILT IN AIR SENSOR The controller should be positioned in a draught free location and cannot be exposed to direct sunlight or another source of heat which could disturb proper temperature measurements The sensor should be installed between 120 and160 cm above floor level ww w elektra pl A 120 160 cm Fig 4 Proper location for the controller ELEKTRA 5 INSTALLING THE CONTROLLER WITH BUILT IN AIR OR FLOOR SENSOR AND ADDITIONAL SENSOR LIMITING FLOOR TEMPERATURE TO 40 C In this configuration the floor sensor prevents the mats and heating cables from overheating Prepare the controller according to the guidelines see tab 1 fig 4 and install the floor sensor see fig 3 www ele 6 TECH2. NICAL SPECIFICATIONS power supply voltage 230 VAC 50 Hz power load at cos 1 max 3600 W res temperature adjustment range from 5 C to 35 C sensitivity lt 0 5 C floor 1 C safety class IP 20 dimensions h w l 80 x 82 x 36 mm installation mode on the plaster surface control light LED switch 1 pole ELEKTRA 7 INSTALLING THE CONTROLLER Once the appropriate temperature measurement method has been chosen and the proper controller installation spot has been determined the installation process can begin Follow the steps described below slacken the fixing screw and remove the controller cover put all wires through the opening in the bottom of the cover using two screws positioned vertically tighten the controller to the installation box observing the diagram connect all wires to the connection strip install the front cover and tighten the fixing screw MA AAA 8 SWITCHING THE CONTROLLER ON AND ITS ADJUSTMENTS The controller is switched on and off with the help of the switch located on the left hand side of its cover position 0 off position 1 on 1 The desired temperature is set with the knob 2 The red LED comes on when the heating circuit is powered 3 ELEKTRA elektra Fig 5 Electronic temperature controller Elektra ELR 10 ww w elektra pl www elektra pl ELEKTRA Our offer comprises Floor heating heating mats and c
3. USER S MANUAL ELEKTRA ELR I0 4 5 electronic temperature Br controller for everyone ww w elektra pl Congratulations on purchasing the Elektra ELR 10 electronic temperature controller Thank you for the trust you have placed in our company The controller will be of use for you and your family for many years to come It will signifi ELEKTRA ELR 10 cantly reduce your energy expenses and will improve the thermal comfort Please read this manual carefully before operating the controller ELEKTRA TABLE OF CONTENTS ntroduction Classification nstalling the floor sensor nstalling the controller with built in air sensor nstalling the controller with built in air or floor sensor and additional sensor imiting floor temperature to 40 C 6 Technical specifications 7 Installing the controller 8 Switching on and adjustments 9 Warranty conditions DI a a gd YAV VAY 1 INTRODUCTION The Elektra ELR 10 electronic temperature controller manages the supply of power to heating elements so that the required optimal temperature can be acquired thus ensuring reduced electricity consumption Elektra ELR 10 uses the three following temperature measurement methods air sensor floor sensor air and floor sensors Depending on the temperature measurement method used prepare the controller in advance by opening or closing relevant connectors The controlle
4. ables temperature controllers self adjusting heating cables frost protection systems heating cables for industrial applications unit heaters bathroom dryers and heaters thermal storage heaters water heaters heat recovery ventilation systems central vacuum cleaning systems ESG EN 29 06 03 1 a XL
5. r preparation procedure is presented in the table below Tab 1 Preparing the controller depending on the temperature measurement method Temperature measurement method Preparing the controller 1 air sensor connectors C D open the controller uses the built in air temperature sensor www elektra pl Temperature Proparin measurement P 9 the controller method 2 floor remove the C D jumper sensor connect the floor sensor to the A D connector 3 air sensor connectors C D closed with floor the controller uses temperature the built in air temperature limited sensor Connect the floor to 40 C sensor to connectors A B ELEKTRA NOTE Electricity supply shall be cut off while installing the controller pi jumper jumper floor floor sensor sensor Fig 1 Preparing the controller depending on the temperature measurement method used ww w elektra pl 2 CLASSIFICATION The product complies with the 2nd protection class reinforced insulation and has to be wired in the following manner connector N neutral wire connector L phase wire connectors N L1 heating device max 3600W Fig 2 Connection diagram for the heating device and controller power supply NINIGIL Heating device max 3600 W 230V 50Hz 230V 50Hz 2 Heating device max 3600 W ELEKTRA
Download Pdf Manuals
Related Search