MULTI XS 7000
Contents
1. MULTI XS 7000 Battery charger For lead acid batteries 14 225Ah User Manual and guide to professional battery charging for Starter and Deep Cycle batteries Model 1007 CEN INTRODUCTION Congratulations on your purchase of your new professional MULTI XS 7000 Switch Mode Charger with Pulse Maintenance Float Analysis and Recond MULTI XS 7000 is a member of a family of professional chargers from CTEK SWEDEN AB It represents the state of the art technology for battery charging A MULTI XS 7000 will prolong the lifetime of your battery Read this user manual and follow the instructions carefully before using the charger SAFETY The charger is designed for lead acid batteries from 14 225Ah Do not use the charger for any other purpose e Use safety glasses and turn your head away when connecting or disconnecting a battery e Battery acid is corrosive Rinse immediately with water if acid comes into contact with skin or eyes Seek medical advice e Make sure that the cable is not pinched or in contact with warm surfaces or sharp edges e While charging a battery can emit explosive gases so it is important to avoid sparks in the immediate area e Always provide for proper ventilation during charging e Avoid covering the charger e Make sure that the electrical cable does not come into contact with water e Never charge a frozen battery e Never charge a damaged battery Do not place the charger on the battery while c2. the flat euro connector is intended for Switzerland VIKMANSHYTTAN SWEDEN 2006 01 23 Borje Maleus VP CTEK SWEDEN AB Rostugnsvagen 3 776 70 VIKMANSHYTTAN SWEDEN Fax 46 225 30793 www ctek com CHARGING TIME The table shows the length of time for bulk charging Battery size Ah Time to 80 charge h 100 INDICATIONS paa SUPPLY O recono 0 LON 5 000980 NORMAL gt SUPPLY RECOND Indication Description 0 Error mode the charger suspends the charging voltage maintenance See further description below Start mode Bulk charging maximum voltage Absorption charging voltage limited to chosen voltage Pulse maintenance charging Supply mode fixed output voltage no counter voltage requirement Recond charging oor wh STANDBY Mode NORMAL 14 4V Mode SNOWFLAKE 14 7V Mode SUPPLY 13 6V Mode RECOND 15 7V 1 5A 0 5 4h moou gt Error mode The charger enters error mode before start in the following situations e The battery is connected with poles reversed to the charger s terminals e The terminals on the charger are short circuited Error mode before start is reset by removing the error situation The charger restarts in the latest selected mode The charger enters steady error mode in the following situations e The charger s analysis function has interrupted charging e The charger is overloaded in Supply mode e The charger has been in start mode lo
3. error mode is indicated This indicates a battery which is faulty or has too large capacity If a large battery is charged that has been severely discharged it may be necessary to restart the charger after 8 hours Start is indicated by lamp 1 Bulk Lamp 2 Primary charging where approximately 80 of the charging happens The charger delivers maximum voltage until the terminal voltage has risen to the preset level After a number of hours the charger goes on to the next phase even if maximum voltage is not reached Bulk is indicated by lamp 2 Absorption Lamp 3 Final charging voltage is kept at the preset level During this phase the voltage is gradually reduced If the maximum length of time for Absorption is exceeded the charger automatically continues with Analysis Absorption is indicated by lamp 3 Analysis Lamp 3 Charging is suspended for a short period and the battery voltage measured If it falls too quickly the battery is probably faulty Charging is suspended and an error is indicated lamp 0 Maintenance charging float Lamp 4 During the first 10 days of maintenance charging the battery is maintained with constant volt age 13 6V Float maintenance is indicated by lamp 4 Maintenance charging pulse Lamp 4 The state of charge varies between 95 and 100 The battery receives a pulse when the voltage sinks keeping the battery in good shape when it is not being used The charger can be connected for months at a
4. the negative pole Connecting the provided cables with eyelet terminals Make sure that the cable is not pinched or in contact with warm surfaces or sharp edges When the cable is mounted on the battery it should not be connected to the charger Connect the eyelet terminals to the battery s poles the red cable to the positive pole and the black cable to the negative pole After this the quick connector can be connected Reverse Polarity Protection If the battery cables are connected incorrectly the reverse polarity protection will make sure that neither the charger nor the battery are damaged In this case the red warning lamp 0 will be lit Start charging 1 Connect the power cord to the power outlet 2 Set the proper charging mode for the battery by pushing the Mode button until the correct setting is lit Choosing settings for your battery is described under BATTERY TYPES AND SETTINGS 3 The lamp for Deep Discharged battery 1 will indicate if the battery voltage is low If lamp 1 blinks this indicates that the battery is lightly sulphated Read more under CHARGING PHASES 4 Normal charging is indicated by the following lamps Deep Discharged 1 Bulk Charge 2 Absorption Charge 3 or Maintenance Charging 4 When the maintenance lamp is lit the bat tery is fully charged The charge will restart if the voltage drops The charger can be connected for months SUPPLY or RECOND are indicated when the lamps for the
5. the output voltage from the charger falls below around 9V and the current is around 7A In the event of an overload the charger goes into error mode lamp 0 Supply mode is indicated with lamp D and lamp 5 Chosen mode RECOND MULTI XS 7000 has a Recond mode which is used to recondition a battery that has been severely discharged The battery is first charged using the mode NORMAL When the analysis phase is complete the charger begins reconditioning the battery by providing a constant current of 1 5A and a maximum voltage of 15 7V After 0 5 4 hours the battery is completely reconditioned and the charger goes into pulse maintenance The battery is ready to be used or store it with pulse maintenance active until you are ready to use the battery Recond is indicated by lamp E and lamp 6 Note that the recond phase begins with normal charging and that the charger therefore will indicate the charging phases according to the descriptions above first Lamp 6 is first lit when the reconditioning begins TEMPERATURE PROTECTION MULTI XS 7000 is protected from being overheated The power will be reduced if the ambient temperature is raised MAINTENANCE The charger is maintenance free Note that disassembly of the charger is not permitted and will void the warranty If the power cord is damaged the charger must be left to the reseller for maintenance The case can be cleaned with a soft damp cloth and mild cleanser The charger should be di
6. time If the battery is charged and or the battery s terminal voltage drops the charger starts a charge pulse until the voltage has reached the preset level 14 4V or 14 7V The charge pulse is then interrupted and the cycle is repeated as long as the charger is in pulse maintenance phase If the terminal voltage drops even lower the charger automatically reverts to the beginning of the charging curve Pulse maintenance phase is indicated by lamp 4 If possible check the water level in the battery Chosen mode SUPPLY MULTI XS 7000 has a Supply mode setting which has a constant voltage of 13 6V and current up to 7A This mode can also be used for maintenance charging of an already fully charged battery called Float maintenance This type of charging keeps the battery at 100 charge The constant small overcharge can also increase water loss A battery does not have to be connected for the charger to deliver voltage This means that the spark protection is not active in this mode Itis not appropriate to charge a completely discharged battery in Supply mode since this will not result in a completely charged battery In this mode MULTI XS 7000 can also be used as a power generation unit for operating equipment that requires 13 6V and a maximum of 7A If the selected current exceeds 7A the output voltage will drop as the load increases The charger has electronic overload protection in this mode which is activated if the charge is so great that
7. MULTI XS 7000 is a multi stage fully automatic charger Type of batteries All types of 12 V lead acid batteries Wet MF AGM and GEL Battery Capacity 14 225Ah Dimensions 191 x 89 x 48 mm Lx Wx H Insulation Pags Weight 0 8kg Back Current Drain is what the charger uses to drain the battery if the power cord is disconnected Quality of the current and voltage are very important High current ripple heats up the battery and makes the positive electrode age prematurely High voltage ripple could harm other equipment connected to the battery MULTI XS 7000 produces a high quality current and voltage with very low ripple If the electrical plug is of the flat euro connector type the battery charger has insulation class IP63 except in Switzerland where IP65 is valid MANUFACTURER S DECLARATION CTEK SWEDEN AB Rostugnsv gen 3 776 70 VIKMANSHYTTAN SWEDEN Declares under sole responsibility that the battery charger MULTI XS 7000 to which this declaration relates is in conformity with the following LVD standards EN 60335 1 EN 60335 2 29 according to the terms of directive 73 23 EEC with the addition of 93 68 EEC This product also is in agreement with the following EMC standards EN 55011 EN 61000 3 3 EN 61000 3 2 EN 55014 1 and EN 55014 2 according to the terms of directive 89 336 EEC with the addition of 92 31 EEC and 93 68 EEC The charger comes in different models with different types of electrical plugs The charger with
8. harging e The electrical connection must fulfil the national heavy current requirements e Check charger cabling before use Make sure there are no cracks in the cabling or in the protective covering A charger with damaged cables may not be used e Always check that the charger has gone over to maintenance charging mode before leaving the charger unattended and connected for long periods If the charger had not gone over to maintenance charging within 3 days this is an indication of a problem In this case the charger must be disconnected manually All batteries fail sooner or later A battery that fails during charging is normally taken care of by the chargers advanced control but certain uncommon errors in the battery can still arise Don t leave the battery charger unattended for a longer period of time e Only mount the charger on a flat surface This equipment may not be used by children or by those who can not read and understand the manual if they are not supervised by a responsible person who can guarantee that the battery charger is being used in a safe manner Store and use the battery charger out of the reach of children Make sure that children do not play with the battery charger BATTERY TYPES AND SETTINGS MULTI XS 7000 can easily be configured to charge many different types of 12V lead acid bat teries wet batteries MF AGM and for most GEL batteries The following recommendations should however only be seen as guideli
9. nes When in doubt always consult the battery manufacturer for further instructions Settings are made by pressing the MODE button and stepping forward by pressing the button one step at a time releasing the button when the required mode is reached After approx 2 seconds the charger activates the chosen mode The selected mode is saved in the charger s memory and remains even when the charger is switched off MODE NORMAL 14 4V Normal setting for wet batteries MF and for most Gel batteries Mode SNOWFLAKE 14 7V This setting is recommended for batteries at temperatures below 5 C It is also recommended for many AGM batteries This setting is not recommended for maintenance charging when the temperature at times exceeds 5 C In this case the NORMAL mode is recommended Mode SUPPLY 13 6V In this mode the charger provides a constant voltage of 13 6V This is the best maintenance mode for batteries where maximum capacity is important for instance for cleaning machinery and golf carts It is not appropriate to charge a completely discharged battery in Supply mode since this will not result in a completely charged battery The MULTI XS 7000 can also be used as a power supply without a battery attached in this setting No counter voltage is required to start the charger in this mode Note that the charger is not spark free in this mode Mode RECOND 15 7V 1 5A 0 5 4h This mode is used to recondition
10. nger than maximum time Steady error mode is acknowledged reset by pressing the MODE button The charger restarts in the latest selected mode a80y0100Z
11. sconnected from the power supply while cleaning EQUIPMENT MULTI XS 7000 is delivered with a set of battery cables with battery pole clamps and a set of battery cables with eyelet terminals WARRANTY CTEK SWEDEN AB Rostugnsvagen 3 776 70 VIKMANSHYTTAN SWEDEN provides a lim ited warranty to the original purchaser of this product This limited warranty is not transferable The unit is warranted against defective workmanship or materials for two years from the date of purchase The customer must return the product together with the original purchase receipt to the place of purchase This warranty is void if the unit is handled carelessly opened or repaired by anyone other than CTEK SWEDEN AB or its authorized representative CTEK SWEDEN AB makes no warranty other than this limited warranty and expressly excludes any implied warranty including any warranty for consequential damages This is the only expressed limited warranty and CTEK SWEDEN AB neither assumes nor authorizes anyone to assume or make any other obligation towards the product other than his limited warranty TECHNICAL SPECIFICATION Model 1007 Voltage AC 170 260VAC 50 60Hz Back current drain lt 1mA Voltage Charging Voltage Nominal 12V 13 6V 14 4V 14 7V or 15 7V Ripple Max 150mV rms max 0 3 A 4 Current 7A max Ambient Temperature 20 C to 50 C power is reduced automatically at increased ambient temperature Cooling Natural convection Charging cycle
12. se settings are lit 5 or 6 5 If the battery cables are connected incorrectly the reverse polarity protection will make sure that neither the charger nor the battery are damaged In this case the red warning lamp 0 will be lit 6 If nothing happens If the setting lamp is lit but no other light comes on the connection to the battery or to the chassis may be poor or the battery may be faulty Start by improving the contact between the battery and the charger 7 Charging can be interrupted at any time by disconnecting the power cord from the wall socket or by putting the charger in Standby mode lamp A Always disconnect the power cord from the socket before removing the battery cables When you interrupt charging of a battery mounted in a vehicle always disconnect the battery cable from the chassis before removing the other battery cable CHARGING PHASES Mode chosen NORMAL or SNOWFLAKE MULTI XS 7000 is a multi stage fully automatic charger Lamp B for chosen setting NORMAL and lamp C for chosen setting SNOWFLAKE Desulphation Lamp 1 blinking Desulphation with pulsing for sulphated batteries Indicated by blinking lamp 1 Start Lamp 1 Starting phase for charging The starting phase continues until the battery s terminal voltage has risen over a preset level At this point charging goes into the bulk phase If the terminal voltage has not reached the preset level within 8 hours charging is suspended The
13. very discharged batteries where you could expect a stratified acid high acid weight in the bottom low on top Use this mode with care because it can cause some water loss 15 7V is normally not a problem for electronics but consult the manufacturer when in doubt Life of light bulbs can be reduced by higher voltages Try to avoid using 12V lamps connected to the battery during this phase Maximum effect and minimum risk for electronics is achieved by disconnecting the battery before charging CHARGING Charging batteries mounted in a vehicle 1 The power cord should be disconnected before connecting or disconnecting the battery leads 2 Identify the pole that is grounded attached to the chassis Ground is normally connected to the negative terminal 3 Charging a negatively grounded battery Connect the red cable to the positive pole of the battery and the black cable to the vehicle s chassis Be careful not to connect the black cable in the vicinity of a fuel pipe or the battery 4 Charging a positively grounded battery Connect the black cable to the negative pole of the battery and the red cable to the vehicle s chassis Be careful not to connect the red cable in the vicinity of a fuel pipe or the battery Charging of a battery not connected to a vehicle 1 The power cord should be disconnected before connecting or disconnecting the battery leads 2 Connect the red cable to the positive pole of the battery and the black cable to
Download Pdf Manuals
Related Search