Hardware Manual
Contents
1. 18 permanently deactivated permanent illumination flashing at 10 Hz 50 ms on 50 ms off flashing at 2 5 Hz 200 ms on 200 ms off short illumination 200 ms then off for 1000 ms two short illuminations 200 ms then off for 1000 ms three short illuminations 200 ms then off for 1000 ms four short illuminations 200 ms then off for 1000 ms flashing at 0 5 Hz 1000 ms on 1000 ms off LED Array Controller V2 Manual Individual extended illumination 1000 ms then off for 200 ms interruption 4 3 3 Power LED S3 no power device is off on logic voltage present device is on 4 3 4 Green Software Status LED S1 booting phase firmware loading approx 10 seconds flashing device in NMT state PRE OPERATIONAL on device in NMT state OPERATIONAL one flash device in NMT state STOPPED 4 3 5 Red Software Error LED S2 no error flashing Invalid configuration general configuration error one flash too many error frames on CAN bus one of the CAN controller error counters has reached its warning limit on the CAN interface is in bus off state no CAN communication possible LED Array Controller V2 Manual 19 5 Initial Startup il IMPORTANT Please carefully read this manual and the associated software manual as well as the LED array manual before starting up your LED array 5 1 Software Installation Install the supplied software drivers before connecting the system The insta2. for inspection and repair 3 3 3 Safe Operation Measures 3 3 3 1 Electromagnetic Emissions The device is designed for usage in any facility including living areas and facilities directly connected to a public supply network that also supplies buildings used for residential purposes 3 3 3 2 ESD Discharge Floors should be wood or concrete or covered with ceramic tiles If floors are covered with synthetic material relative air humidity must be at least 30 3 3 3 3 Electrical Disturbances Supply voltage quality should be equal to a typical business or hospital environment 3 3 3 4 Magnetic Disturbances Power lines including those of other devices should not be placed near the device or its cables Portable and mobile two way radios should be kept at the minimum safe distance from the device and its wiring 3 3 4 Device Condition Despite flawless workmanship the device may be damaged during operation Therefore you should visually inspect the device before each use Pay particular attention to crushed cables and deformed plugs If you find any damage please refrain from using the device and contact cetoni GmbH immediately We will repair your device as soon as possible Never attempt to repair the device yourself LED Array Controller V2 Manual 13 3 4 Warranty and Liability The device has left our facilities in perfect condition and may only be opened by cetoni GmbH If the device is opened by an unautho
3. or intended for operation in potentially explosive environments Therefore using the device in such environments is forbidden e When operating the device the laws and regulations applicable at the place of operation must be observed In the interest of a safe work process operators and users are responsible for observing such regulations e When radiating substrates with light of various wavelengths energy enters into the substrate There is also a possibility of creating chemical exothermic reactions in the substrate The substrate may ignite e The operator must make sure that there is no ignition The operator must ensure that any ignition is extinguished immediately Flammable substances may be exposed to radiation only under continuous supervision e Before each operation of the device the user has to ensure that the device is functioning safely and is in proper condition e The user must be familiar with the operation of the device e Before starting operation the device and wiring must be checked for damage Damaged wires and plugs must be replaced immediately e If a support or tripod is used it must be sufficiently stable and able to support the required weight e Cables must be routed in such way as to rule out any trip hazards 12 LED Array Controller V2 Manual e If liquid enters the device the main power plug must be pulled out of the mains socket immediately The device must then be sent to cetoni GmbH
4. 3 05 2015 Text modification for ceLED LED array controller V2 6 LED Array Controller V2 Manual 2 Introduction 2 1 Preface Thank you for choosing a cetoni product With this manual we would like to support you in using the device For additional questions or comments please feel free to contact us directly Please read this manual carefully before operating the device 2 2 Symbols and Keywords This manual uses the following symbols intended to help you navigate the document TIP User tips and useful information to simplify the use of the software a IMPORTANT Important information and additional particularly useful information This symbol does not refer to dangerous or hazardous situations A CAUTION A potentially hazardous situation Failing to avoid it may cause damage to the product or its environment LED Array Controller V2 Manual 7 WARNING A potentially dangerous situation Failing to avoid it may cause light or insignificant injury or material damage LED Array Controller V2 Manual 3 Basic Information 3 1 Radiation Protection Advice A WARNING Emitted light can cause damage to skin and eyes including the risk of blindness Therefore when integrating this device into your application you should take special care not to expose persons animals or items to the emitted light inadvertently Persons operating the LED array must wear suitable gear to protect against dangers cause
5. CELED LED ARRAY Original Operating Manual 1 01 May 2015 ceLED LED Array Controller V2 Hardware Manual II a C2 cetoni The information and data contained in this document are subject to change without prior notice No part of this document may be copied or transmitted without the express consent of cetoni GmbH irrespective of the means used for this purpose electronic or mechanical The general terms of cetoni GmbH apply Agreements deviating from these terms must be made in writing Copyright cetoni GmbH Automation and Micro Systems All rights reserved 2 neMAXYS Hardware Manual C cetoni cetoni GmbH Wiesenring 6 07554 Korbussen Germany Tel 49 0 36602 338 0 Fax 49 0 36602 338 11 E Mail info cetoni de Internet www cetoni de LED Array Manual 1 Overviews and Directories 1 1 Contents 1 Overviews and Directories sentent eee 4 E CON MES 22 de a ea aa less E E a a 4 12 Revision HIStOFY sieisen 6 2 NtrodUCtiO Nesco serres enen neneeese EEEE EEEE aaah 7 21 PEAR ed le 7 2 2 Symbolsand KeyWwordS ssserssescssesiisserirssrserssisirerssvsinestsrisserinstseiiiiieress 7 3 Basic Information ce heaney a nm mea bee 9 3 1 Radiation Protection AAVICE x wisnsivaninvacnenseradersnnnpeandsiansteraiaaneinnsanniantianntres 9 3 2 Standards and GUIGSMMES pcssessnccsarccsorssargnerinensvacsseanvensoeiaderscarnoonecnennes 10 2 Intended USE an ur rs rate 11 3 3 1 General Description
6. d by artificial optical radiation It must also be ensured that persons without UV protection cannot enter the UV radiation area If required the UV radiation area must be enclosed by a radiation proof barrier Depending on the type of radiation additional safety measures stipulated by the LED manufacturer may apply Please be aware that the emitted radiation may cause various types of damage to skin and eyes LED Array Controller V2 Manual 9 The following table shows possible types of radiation damage Wave Length Skin Damage Eye Damage 280nm 400nm Accelerated skin aging Corneal inflammation UVA and UVB radiation isnot stronger pigmentation and conjunctivitis lens visible burns risk of cancer opacity 400nm 800nm Skin reddening burns Photochemical and visible spectrum thermal damage to retina and receptors 800nm 1550nm Skin reddening burns Lens opacity retinal IR radiation is not visible burns A WARNING Always avoid direct radiation into the eyes Even low radiation intensity can cause glare or even injury WARNING Never look directly at presumably inactive LEDs The LEDs in question may emit radiation outside of the visible spectrum which can also cause damage or injury 3 2 Standards and Guidelines cetoni GmbH hereby declares under its sole responsibility that the ceLED LED array controller complies with the health and safety requirements of the relevant European guide
7. lines 10 LED Array Controller V2 Manual 3 3 Intended Use 3 3 1 General Description of the Device The LED array controller controls LED array devices made by cetoni GmbH These LED arrays are used for the irradiation of separate areas with LEDs of similar or different wavelengths With this control unit the radiation intensity can be adjusted separately for each area channel The maximum intensity and wavelength of the emitted radiation is governed by the number and type of LEDs being used on the connected LED arrays At the time of creating this document LEDs ranging from 255 nm to 1550 nm in wavelength are commercially available fig IMPORTANT The device must not be used as a medical product or for medical purposes The device must not be used on people or for therapeutic purposes A WARNING The device must not be used in potentially explosive environments There is a risk of fire when exposing flammable substances substrates 3 3 2 Satety Measures Operator safety and failure free operation of the device can only be guaranteed when using original equipment parts Warranty claims are void if damage was caused by using third party equipment or third party material The device was developed in such way as to largely rule out dangers if used properly Nevertheless you should observe the following safety measures to rule out any residual danger LED Array Controller V2 Manual 11 e The device is not designed
8. llation is described in the software manual which is stored on the supplied CD or USB stick as QmixElements_Handbuch_DE pdf in the Manual folder n IMPORTANT Install the QmixElements software device drivers as described in the software manual before connecting the device to a PC via USB 5 2 Connecting the LED Array Module Connect the LED array modules to the LED array connector 1 J7 on the rear panel of the LED array controller using the supplied cable set 5 3 Connecting the Device to a PC Connect the USB plug of the supplied USB RS232 adapter to a free USB socket on the PC USB type A Connect the RS232 DSub plug of the USB RS232 adapter with the DSub socket of the RS232 connection cable Plug the DSub plug of the connection cable into the RS232 socket J4 on the LED array controller Connect the power supply to the 24V connector J6 on the LED array controller Connect the power cable of the power supply to the mains power outlet 20 LED Array Controller V2 Manual WARNING Risk of injury due to damaged wires and plugs Before operating the device check the device and all wires for damage Never operate the device with damaged wires or plug connectors 5 4 Establishing a Connection Launch the QmixElements software and establish a connection to the device Additional details about software operation can be found in the QmixElements software manual A PDF file of the software manual is stored on your compu
9. ntroller V2 4 2 Overview of Interfaces 4 2 1 Front Interfaces The front panel contains all interfaces needed to connect the LED array controller to a PC or other controller 16 LED Array Controller V2 Manual 6 2 Ep Image 2 Front Panel Interfaces Connector Interface J1 USB device interface optional J2 Ethernet interface optional J3 CAN interface optional J4 RS232 interface to connect a PC or other controller J5 CAN 24 V interface for connection to Qmix systems J6 Power connection J6 4 2 2 Rear Interfaces The rear panel contains all interfaces needed to connect LED arrays to the LED array controller Image 3 Rear panel interfaces Connector Interface J7 Connector for LED array 1 and LED array 2 optional J8 1 0 interface optional to connect external 1 0 signals LED Array Controller V2 Manual 17 AS Status LEDs 4 3 1 Overview The front panel contains various LEDs showing you the status of the device Image 4 LED signals on front panel Software Status LED S2 Software Error LED s3 Power LED illuminates when connected to a power supply S4 RS232 LED flashes during data transfer via RS232 interface S5 LED array 1 and LED array 2 status LEDs illuminate when the connected LED array is illuminated S6 4 3 2 Description of LED Status off on flashing flashing one flash two flashes three flashes four flashes flashing slowly
10. of the Device 11 3 3 2 Safety MeEaSUrES neue aE 11 3 3 3 Safe Operation Measures ss 13 3 34 Device Conditio Ms ae nn dan 13 3 4 Warranty and Liability essensen 14 3 5 SCOR SOT Supply oce naine 15 A Interfaces and Connections siemens 16 Beds IAtrOdUCtiON isinen aiaa a EEEE Taa eaaa 16 4 2 Overview of Interfaces nccsuiasnarncsinmgeanddnnwqreassansdnsstetaadiaaunnannemuyrnaey 16 4 2 1 Front Int rnfaCE Sisinnio nono 16 4 2 2 Real IM MAC SS nomma era landes 17 43 Statys LEDS da dan dr mn 18 3 1l OV rVieWi nes in cectea E T ait 18 4 3 2 Description of LED Satis seciassaatetasashacdadeasacsavds nantais 18 43 3 Power LED S3 misran ai nana conne 19 4 LED Array Controller V2 Manual 4 3 4 Green Software Status LED ST 4 sad ed 19 4 3 5 Red Software Error LED S2 ssssciciitincticccharsecpeueasiieesaneuedinaiiieieeneibiieascn 19 5 Initial StartUp a an nota ane ri niet 20 5 1 Software Imation man ana ne 20 5 2 Connecting the LED Array Module 20 5 3 Connecting the Device to a PC w ccccsccicccssisescssssecsancesissnndensdeccearsaecceannveces 20 5 4 Establishing a Connectidns ss una aie 21 6 Transport Maintenance Disposal ccccccssssssseeeeeceeeeeeseaaeeeeees 22 6 1 Transport and SOA assessment 22 6 2 Maintenance anale sua nd dal 22 6 3 DISSE asda asic Gaeta a Donets nn te 22 LED Array Controller V2 Manual 5 1 2 Revision History 1 00 02 01 2015 Creation of ceLED LED array manual 1 01 0
11. rized person all warranty and liability claims shall be void in particular those referring to personal injury The warranty period is 1 year from the day of delivery Any work done on the device within this period shall not extend or renew the warranty cetoni GmbH assumes responsibility for its devices with respect to safety reliability and function only if installation readjustment changes extensions and repairs are done by cetoni GmbH or an authorized party and if the device is used in accordance with the user manual The device complies with the applicable safety rules and standards cetoni GmbH reserves all property rights for the relevant wiring processes names software and devices 14 LED Array Controller V2 Manual 3 5 Scope of Supply The following items should be included in the delivery 24V Power Supply USB RS232 Adapter RS232 Connection Cable CD ROM QmixElements including e Device driver e QmixElements Software e Qmix SDK e Device configuration LED Array Controller V2 Manual 15 4 Interfaces and Connections 4 1 Introduction Each ceLED LED array consists of an LED array controller and one or several LED array modules The LED array modules vary in the number and typical wavelength of the LEDs used in them and are often customized The LED array controller contains the control electronics for the LED array modules and PC interfaces Image 1 ceLED LED array co
12. ter during the installation of QmixElements software LED Array Controller V2 Manual 21 6 Transport Maintenance Disposal 6 1 Transport and Storage If possible use the original package for transporting and shipping the device Otherwise use a stable box and a sufficient amount of padding material 6 2 Maintenance and Care When used properly the device is maintenance free Should you experience problems that you can t fix yourself or that require opening the device please contact cetoni GmbH to discuss further actions The device may only be opened by cetoni GmbH or authorized service personnel Violation of this rule will void the warranty and liability The software manual provides additional information about problems in connection with operating software Wipe the device with a moist not wet cloth Make sure that no liquid can enter the inside of the device For stronger soiling you may use a small amount of detergent or alcohol 6 3 Disposal Please return your old devices to cetoni GmbH We will take care of proper disposal according to the relevant electrical and electronic device regulations 22 LED Array Controller V2 Manual
Download Pdf Manuals
Related Search