Home
SlimPANEL Tri 12 User Manual Rev. 4
Contents
1. 2 INTRODUCTION Product Overview Touch Display Power In Power Out DMX In Mounting Bracket DMX Out m d SlimPANEL TRI 12 IP User Manual Rev 4 Page 5 of 18 Product Dimensions d Page 6 of 18 SlimPANEL TRI 12 IP User Manual Rev 4 3 SETUP AC Power The SlimPANEL TRI 12 IP has an auto ranging power supply and it can work with an input voltage range of 100 240 VAC 50 60 Hz To determine the products power requirements circuit breaker power outlet and wiring use the current value listed on the label affixed to the product s back panel or refer to the product s specifications chart The listed current rating indicates the product s average current draw under normal conditions Always connect the product to a protected circuit circuit breaker or fuse Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire To eliminate wear and improve its lifespan during periods of non use completely disconnect from power via breaker or by unplugging it Never connect the product to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch Power Linking The product provides a power linking option via the pigtails located on the back of the unit You can daisy chain up to 19 units on 120 VAC or up to 39 units on 230 VAC If you choose not to use the power linking feature b
2. ENTER to disable the touch panel lock 2 Press MENU to move through the menus as normal In situations where water may flow onto the touch display use the Touch Panel Control Lock so that the water does not reset the product s settings Master Slave The Master Slave mode allows a single SlimPANEL TRI 12 IP unit the master to Mode control the actions of one or more SlimPANEL TRI 12 IP units the slaves without the need of a DMX controller The master unit will be set to operate in either Automatic or Sound Active mode while the slave units will be set to operate in Slave Mode Once set and connected the slave units will operate in unison with the master unit Configure the units as indicated below Slave units 1 Press MENU repeatedly until Addr shows on the display Press ENTER to accept Set the DMX address to 001 Connect the DMX input of the first slave unit to the DMX output of the master unit Connect the DMX input of the subsequent slave units to the DMX output of the previous slave unit 6 Finish setting and connecting all the slave units Master unit 1 Set the master unit to operate in Static Color Mode Automatic or Custom Static Color mode 2 Make the master unit the first unit in the daisy chain Configure all the slave units before connecting the master unit to the daisy chain Never connect a DMX controller to a DMX string configured for Maste
3. UP or DOWN to select the starting address 3 Press ENTER Page 10 of 18 SlimPANEL TRI 12 IP User Manual Rev 4 DMX Channel Assignments and Values 3 CH Channel Function Value Setting 0000 255 0 100 2 Green 0000 255 0 100 3 Blue 000 255 0 10025 4 CH Channel Function Value Setting 1 Dimmer 0000 255 0 007 2 Red 255 o 100 3 Gren 0000 255 o 100 4 Blue 000 U 255 0 100 5 CH Channel Function Value Setting 1 000 255 0 100 Green 1 0000 255 0 100 000 U 255 0 100 Dimmer 0000 255 0 100 000 010 No function Strobe 011 U 255 Slow to fast O1 SlimPANEL TRI 12 IP User Manual Rev 4 Page 11 of 18 9 Channel Function Value Setting 1 Dimmer 0000 255 0 100 2 0000 255 0 100 3 Green 0000 255 0 100 4 Blue 0000 255 0 100 000 U 010 function 014 200 Color Macros 201 0 205 White 1 3200K 206 U 210 White 2 3400 211 U 215 White 3 4200K 216 0 220 White 4 4900 5 Color Macros 221 225 White 5 5600K 226 230 White 6 5900K 231 235 White 7 6500K 236 240 White 8 7200K 241 245 White 9 8000K 246 250 White 10 8500K ma p 255 White 11 10000K 000 U 009 No function 255 0 10095 slow to fast 000 U 051 No function 052 0 101 Auto Program 1 102 U 152 Auto Program 2 7 Auto Programs 9 153 U 203 Auto Program 204 U 254 Au
4. As a suggestion proper UPS packing or double boxing is always a safe method to use Chauvet reserves the right to use its own discretion to repair or replace returned product s SlimPANEL M TRI 12 IP User Manual Rev 4 Page 17 of 18 CONTACT US Page 18 of 18 WORLD HEADQUARTERS Chauvet General Information Technical Support Address 5200 NW 108 Avenue Voice 954 577 4455 Press 4 Sunrise FL 33351 Fax 954 756 8015 Voice 954 577 4455 Email tech chauvetlighting com Fax 954 929 5560 Toll free 800 762 1084 World Wide Web www chauvetlighting com UNITED KINGDOM AND IRELAND Chauvet Europe Lid General Information Technical Support Address Unit 1C Email uktech chauvetlighting com Brookhill Road Industrial Estate Pinxton Nottingham UK World Wide Web NG16 6NT www chauvetlighting co uk Voice 44 0 1773 511115 Fax 44 0 1773 511110 MEXICO Chauvet Mexico General Information Technical Support Address Av Santa Ana 30 Email servicio chauvet com mx Parque Industrial Lerma Lerma Mexico C P 52000 World Wide Web www chauvet com mx Voice 52 728 285 5000 CHAUVET EUROPE Chauvet Europe BVBA General Information Technical Support Address Stokstraat 18 Email Eutech chauvetlighting eu 9770 Kruishoutem Belgium World Wide Web www chauvetlighting eu Voice 32 9 388 93 97 Outside the U S United Kingdom Ireland Mexico or Benelux contact your dealer Follow their instructions to request support or
5. If you are located in Benelux contact Chauvet Europe BVBA If you are located in any other country DO NOT contact Chauvet Instead contact your local distributor See www chauvetlighting com for distributors outside the U S UK Ireland Mexico or Benelux distributor of record and follow their instructions on how to return Chauvet E If you are located outside the U S UK Ireland Mexico or Benelux contact your EZ ial products to them Visit our website www chauvetlighting com for contact details Returns the corresponding Chauvet Tech Support office and request a Return Merchandise Authorization RMA number before shipping the product Be prepared to provide the model number serial number and a brief description of the cause for the return You must send the merchandise prepaid in its original box and with its original packing and accessories Chauvet will not issue call tags Clearly label the package with the RMA number Chauvet will refuse any product returned without an RMA number Write the RMA number on a properly affixed label DO NOT write the RMA number directly on the box Before sending the product clearly write the following information on a piece of paper and place it inside the box Your name Your address Your phone number The RMA number A brief description of the problem Be sure to pack the product properly Any shipping damage resulting from inadequate packaging will be your responsibility
6. S Strobe rate S 1 Auto program selection and speed Auto Programs pe 5100 selection P5 SlimPANEL TRI 12 IP User Manual Rev 4 Page 9 of 18 Configuration Set the product in DMX mode to control with a DMX controller DMX 1 Connect the product to a suitable power outlet Turn the product on 3 Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the product DMX The SlimPANEL TRI 12 IP has 4 DMX personalities from a 3 channel mode for basic Personalities control to a 9 channel mode with more advanced control over the lights The SlimPANEL TRI 12 IP uses up to 9 DMX channels in its 9 channel DMX mode and Starting which defines the highest configurable address to 504 Address When selecting a starting DMX address always consider the number of DMX channels the selected DMX mode uses If you choose a starting address that is too high you could restrict the access to some of the product s channels If you are not familiar with the DMX protocol you may refer to the DMX Primer at www chauvetlighting com To select the DMX personality do the following 1 Press lt MENU gt repeatedly until PERS shows on the display 2 Use UP or lt DOWNs gt to select 3CH 4CH 5CH or 9CH Press ENTER to choose your DMX personality when it appears on the display To then choose your starting address 1 Press lt MENUs gt repeatedly until Addr shows on the display 2 Use
7. of 18 6 TECHNICAL SPECIFICATIONS Dimensions and Length Width Height Weight Weight 14 in 358 mm 7 in 180 mm 3 5 in 90 mm 10 5 Ibs 4 8 kg Note Dimensions in inches rounded to the nearest decimal digit Power Power Supply Type Range Voltage Selection Switching internal 100 240 V 50 60 Hz Auto ranging Parameter 120 V 60 Hz 230 V 50 Hz Consumption 46 W 46 W Operating 0 4A 0 2A Power linking current units 8 A 19 units 8 A 39 units Power I O U S Worldwide UK Europe Power input connector Proprietary Proprietary Power output connector Proprietary Proprietary Power Cord plug Edison U S Local plug Light Source Type Power Lifespan LED 3 W 50 000 hours Color Quantity Current Tri color 12 350 mA x3 Photometrics Parameter Strobe Rate 0 to 27 Hz Illuminance 2m 3 576 lux Beam angle 20 Field angle 34 Thermal Maximum External Temp Minimum Startup Temp Cooling System 113 F 45 C 4 F 20 C Convection DMX Connectors Connector Type Channel Range 3 pin XLR Proprietary 3 4 5or9 Ordering Product Name Item Code UPC Number SlimPANEL TRI 12 IP 03030525 781462208738 UL 1573 8 CSAC22 2 No 166 C US E113093 Page 16 of 18 SlimPANEL TRI 12 IP User Manual Rev 4 In case you need to get support or return product If you are located in the U S contact Chauvet World Headquarters If you are located in the UK or Ireland contact Chauvet Europe Ltd If you are located in Mexico contact Chauvet Mexico
8. to return a product Visit our website for contact details SlimPANEL TRI 12 IP User Manual Rev 4
9. SIMPANEL 6 12 IP User Manual TABLE OF CONTENTS Page 2 of 18 Ms Idee 3 La arse GG ERE 3 Unpacking IASTUCIONS tse eb c E 3 E ante m rey 3 Text GODVellllolS re yi fo PP Pe PT an CP 3 ICONS NR ER TORO UD 3 BB fer are te et UNTERE nn 3 gp 00 Uy Bers prs WC g gt T D OT EU 4 M c T 4 2 iris Ub Ra an Dun eure cu rel ER un pau rx OR 5 PFOOCUGCT OVER VIC RR T T rrr 5 Product DIMENSIONS cla esent istssck kn 6 UU we 7 AC FOWO 7 Power ONKIN t P e ea O 7 MOUNN UE 8 osos n Me i e IE tas ELE EE 8 mise PEPEE E ES EET 8 d EEE 9 Control Panel Operation cccccccccecccsssseeeececeeeeeeeeseeceeeeeeseeeseeeeeeeeesseaegeeeeeeees 9 Menu II OM ETE TR Tm 9 Configuration DMX ssssesssssseeseeeeeeennnn nennen nennen nnn nn nnn nnns nnn nnn nnns 10 DMX Personalities and Starting Address 10 DMX Channel Assignments and 11 or Kr ae Pe nn en ee een VERTE Aer ee a ee eee 11 n E m 11 ERY ree ete ESEE ah RM Ex M MM E MEI MIR MEE 11 SG r ae d LM I MM IU M 12 Configuratio
10. d mount the products close enough for the cable to reach This product is for indoor or outdoor use IP65 Do not expose to harsh or excessively corrosive environmental conditions whether indoors or outdoors including but not limited to extreme temperatures humidity atmospheric conditions including salinity or pressure radiation UV infrared or nuclear shock and conditions which exceed the product s Ingress Protection IP rating Do not submerge this product Mounting Bracket SlimPANEL TRI 12 IP User Manual Rev 4 4 OPERATION Control Panel To access the control panel functions use the four buttons located underneath the ai Please refer to the Product Overview to see the button locations on the control Button Function lt MENU gt Press to find an operation mode or to back out of the current menu option lt UP gt Press to scroll up the list of options or to find a higher value lt DOWN gt Press to scroll down the list of options or to find a lower value lt ENTER gt Press to activate a menu option or a selected value Menu Map Mode Programming Steps Description DMX Address Addr d_1 d512 Selects the DMX starting address Personalities Selects DMX personality Dimmer UN Change dimmer speed mx 3 EN Static Colors eee eens 3 rales ate Touch Control ON Locks touch control panel Panel Lock OFF Pesscodei is UPDOWN UP DOWN ENTER Custom Color Mixing a
11. e stated on the decal or rear panel of the product This product is for indoor or temporary outdoor use IP65 Do not expose to harsh or excessively corrosive environmental conditions whether indoors or outdoors including but not limited to extreme temperatures humidity atmospheric conditions including salinity or pressure radiation UV infrared or nuclear shock and conditions which exceed the product s Ingress Protection IP rating Do not submerge this product Always install the product in a location with adequate ventilation at least 20 in 50 cm from adjacent surfaces D Be sure that no ventilation slots on the product s housing are blocked Never connect the product to a dimmer Make sure to replace the fuse with another of the same type and rating Never carry the product from the power cord or any moving part Always use the hanging mounting bracket or the handles The maximum ambient temperature Ta is 104 F 40 C Do not operate the product at higher temperatures In the event of a serious operating problem stop using the product immediately Never try to repair the product Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Keep this User Manual for future consultation If you sell the product to another user be sure that they also receive this document Page 4 of 18 SlimPANEL TRI 12 IP User Manual Rev 4
12. e sure to use the included screw on cap to prevent any water from getting into the power cords The power linking information above corresponds to the North American version of the product ONLY If using the product in other markets you must consult with the local Chauvet distributor as power linking connectors and requirements may differ in your country or region SlimPANEL M TRI 12 IP User Manual Rev 4 Page 7 of 18 Mounting Orientation Rigging Mounting Diagram Page 8 of 18 Before mounting the product read and follow the safety recommendations indicated in the Safety Notes The SlimPANEL TRI 12 IP may be mounted in any position however make sure adequate ventilation is provided around the product Before deciding on a location for the product always make sure there is easy access to the product for maintenance and programming purposes Make sure that the structure onto which you are mounting the product can support the product s weight See the Technical Specifications for weight information When mounting the product overhead always use a safety cable Mount the product securely to a rigging point whether an elevated platform or a truss When rigging the product onto a truss you should use a mounting clamp of appropriate weight capacity The bracket has a 13 mm hole which is appropriate for this purpose When power linking multiple products you must always consider the length of the power linking cable an
13. n Standalone cccccccsseeeeceeceeeesceeeeseecseeeeesaeeeceseesaaeeeeeesseeeeees 13 AUTOMATIC M dra naen a 13 Golfo gt Sener nee nee DR en EE ROR CR ne Ee CO ONO ee 13 Custom Static Color Mode essen emen nennen nnne nnne nnns 13 Dimmer Adjustment ate c cS 13 TouchGontrol Panel EO6Kuseioi ero oo due t RUE ve eo quo ma Dex t adeat e due que 14 Visi fie zh MISTER T 14 5 Technical Information 15 mide eU EMI RIT TT TT 15 6 Technical Specifications 16 aiia Tp c 17 OAC ai DH 18 SlimPANEL TRI 12 IP User Manual Rev 4 1 BEFORE YOU BEGIN What Is SlimPANEL TRI 12 IP Power Cord DMX In Adapter Warranty Card Included P y DMX Out Adapter Quick Reference Guide Unpacking Immediately upon receipt carefully unpack the product and check the container to make sure you have received all the parts indicated above in good condition Instructions Claims f the container or the material inside the container the product and included accessories appear damaged from shipping or show signs of mishandling upon receipt notify the carrier immediately not Chauvet Failure to do so in a timely manner may invalidate your claim with the carrier In addition keep
14. r Slave operation because the controller may interfere with the signals from the master unit Do not connect more than 31 slave units to the master unit Page 14 of 18 SlimPANEL TRI 12 IP User Manual Rev 4 5 TECHNICAL INFORMATION Product Dust build up reduces light output performance and can cause overheating This can lead to reduction of the light source s life and mechanical wear To maintain optimum Maintenance performance and minimize wear you should clean your lighting products at least twice a month However use and environmental conditions could be contributing factors to increased cleaning To clean the product follow the instructions below 1 2 3 Unplug the product from power Wait until the product is at room temperature Use a vacuum or dry compressed air and a soft brush to remove dust collected on the external surface vents Clean all external optics and glass transparent surfaces with a mild soap solution ammonia free glass cleaner or isopropyl alcohol Apply the solution directly to a soft lint free cotton cloth or a lens cleaning tissue Softly drag any dirt or grime to the outside of the external optics or glass transparent surface Gently polish the external optics and glass transparent surfaces until they are free of haze and lint cleaning them D Always dry the external optics and glass transparent surfaces carefully after SlimPANEL M TRI 12 IP User Manual Rev 4 Page 15
15. tatic Color Mode follow the instructions below Color Mode 1 Press MENU repeatedly until U shows on the display Press ENTER to choose between colors r g b Press UP or lt DOWNsS to choose the intensity of the color 000 100 Repeat the steps to mix additional colors to create the color you need Press ENTER You also manually adjust the strobe rate do so do the following 1 Press MENU repeatedly until U shows on the display 2 Press ENTER until S shows on the display 3 Press UP or lt DOWNS to choose the strobe rate S 0 5 20 4 Press ENTER once you have chosen your desired strobe rate Dimmer You can manually control the dimmer speed to suit any need To set up your preferred Adjustment dimmer speed do the following 1 Press MENU repeatedly until DIM shows on the display 2 Press ENTER 3 Use UP or DOWN to choose between the dimming types OFF DIM3 4 Press ENTER SlimPANEL M TRI 12 IP User Manual Rev 4 Page 13 of 18 Touch Control enable the touch panel lock follow the instructions below Panel Lock 1 Press lt MENUs gt repeatedly until PASS shows on the display 2 Press ENTER 3 Press UP or lt DOWN gt until ON shows on the display to enable the touch panel lock To disable the touch panel lock so you can resume functionality follow the steps below 1 Press UP DOWN UP DOWN
16. the container and all the packing material for inspection For other issues such as missing components or parts damage not related to shipping or concealed damage file a claim with Chauvet within 7 days of receiving the merchandise Text Convention Meaning Conventions 1 512 A range of values 50 60 A set of values of which only one can be chosen Settings A menu option not to be modified Menu Settings A sequence of menu options to be followed ENTER A key to be pressed on the product s control panel ON A value to be entered or selected Icons Icon Meaning Critical installation configuration or operation information Failure to comply with this information may render the product partially or completely inoperative cause damage to the product or cause harm to the user Important installation or configuration information Failure to comply with this information may prevent the product from functioning correctly Useful information Je gt Disclaimer The information and specifications contained in this document are subject to change without notice Chauvet assumes no responsibility or liability for any errors or omissions that may appear in this manual Chauvet reserves the right to update the existing document or to create a new document to correct any errors or omissions You can download the latest version of this document from www chauvetlighting com O Copyright 2015 Chauvet All rights reserved Electronically p
17. to Program 4 Auto Program 5 8 Auto Program Speed 000 U 255 Slow to fast when Ch 7 is between 052 255 Default speed 052 0 101 Linear dimmer 9 Dimmer Curve 102 U 152 Nonlinear dimmer 1 153 U 203 Nonlinear dimmer 2 204 U 255 Nonlinear dimmer 3 Page 12 of 18 SlimPANEL TRI 12 IP User Manual Rev 4 Configuration Set the product in one of the standalone modes to control without a DMX controller Standalone 1 Connect the product to a suitable power outlet Turn the product on Automatic or Sound to a DMX string connected to a DMX controller Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller Never connect a product that is operating any standalone mode Static Automatic Mode To enable the Automatic Mode follow the instructions below 1 Press MENU repeatedly until P shows on the display Press ENTER Use UP or lt DOWNs to choose an auto program P1 P5 Press ENTER to adjust the speed of the program Use UP or DOWN to adjust the duration of each step of the automatic program from S 1 fast to S100 slow 6 Press ENTER CE cm Static Color Mode To enable the Static Color Mode follow the instructions below 1 Press MENU repeatedly until C shows on the display 2 Press ENTER Use UP or DOWN to choose a color C1 C7 4 Press ENTER Custom Static enable the Custom S
18. ublished by Chauvet in the United States of America Author Date Editor Updated M Trouard 05 07 15 R Isenstadt 05 07 15 SlimPANEL TRI 12 IP User Manual Rev 4 Page 3 of 18 Auto Programs Auto ranging Power Supply Product at Use on Dimmer Glance Outdoor Use Sound Activated DMX Master Slave User Serviceable Duty Cycle P P x X X Safety Notes Please read the following Safety Notes carefully before working with the product The Notes include important safety information about installation usage and maintenance Always connect the product to a ground fault interrupter circuit to avoid the risk of electrocution To eliminate wear and improve its lifespan during periods of non use completely disconnect from power via breaker or by unplugging it Always disconnect the product from the power source before cleaning or replacing the fuse N Avoid direct eye exposure to the light source while the product is on Make sure the power cord is not crimped or damaged Never disconnect the product from power cord by pulling or tugging on the cord If mounting the product overhead always secure to a fastening device using a safety cable Make sure there are no flammable materials close to the product when operating Do not touch the product s housing when operating because it may be very hot Always make sure that the voltage of the outlet to which you are connecting the product is within the rang
Download Pdf Manuals
Related Search
Related Contents
INSTRUCTION MANUAL MODEL No.: PL167GWA "取扱説明書" Global Door Controls GAL-1151L-R-626 Installation Guide Mode d`emploi K 05 NF, K 08 NF, K 06 NF, K 09 NF Mode d ASUS A88X-PRO F8565 User's Manual 取扱説明書 - 日立の家電品 Koolatron TCFT02 User's Manual Copyright © All rights reserved.
Failed to retrieve file