COUNTER - Electronic Displays, Inc.
Contents
1. b b B b 0000 0606 COUNTER User s Manual 1 KEYPAD LAYOUT 12 24 Key RST key U D key L R key S 1 key S 1 key START key STOP key i DISPLAY BOARD SECTION Set 12 24 hour format only for the TIMER Reset the Counter The Counter toggles between upcount and downcount Select the left or right two digits to adjust Increase by 1 Decrease by 1 Run the Counter Stop the Counter 2 POWER ON SET UP THE DISPLAY BOARD 100 240AV sej 1 Plug the appropriate end of the DC Power Adapter into the power receptacle on the Display Board 2 Plug the DC Power Adapter into a standard 100 240VAC outlet 3 Once the Display Board is powered on it begins to work First It will cycle through a diagnostic display and then run the last selected function 3 SELECT THE DISPLAY BOARD FUNCTION There are function selection switches on the side of the Display Board Below is the function list when selection switches are at different status The Counter function switch mo MODEL 109 on Up Counter mas Lo MODEL 110 on Up Down Counter Note After selecting a new function by selection switches you need to reboot the Display Board to let the new function take effect 4 OPERATION INSTRUCTION up counter model 109 1 Press S 1 key will increase by 12. 2 Press Reset key will make the Counter reset and display 0 up down counter model 110 1 Press U D key will make the Counter alternative between up count and down count 2 Press S 1 will increase by 1 and press S 1 will decrease by 1 3 To adjust the preset number press L R key to select two digits which will be adjusted The selected two digits will flash 4 Press S 1 or S 1 to set desired number If press S 1 or S 1 for 3 seconds the number will be adjusted quickly 5 Press L R key again to select the other two digits and then adjust to desired number 6 Press START to finish presetting the number 5 COMMUNICATION PROTOCOL HE nterface method RS232 RS485 Baud Rate 9600 bps 8 N 1 Data structure lt STX gt message lt ETX gt lt STX gt are ASCII code lt S T X amp gt denotes the beginning of data package lt ETX gt are ASCII code lt E T X amp gt denotes the end of data package The middle messages between lt STX gt and lt ETX gt may vary according to detailed function or operation 1 Set Display Board ID lt STX gt lt ID gt lt xx gt lt ETX gt lt ID gt ASCII code lt TV D amp gt xx the range from 00 to FF the Hex number in ASCII format 1 UP COUNTER MODEL 109 2 UP DOWN COUNTER MODEL 110 lt STX gt lt xx gt lt IN gt lt ETX gt lt STX gt lt xx gt lt DAyyyy gt lt ETX gt Send the preset number Increase the Counter by 1 xx denotes t
3. elect the 2 Click on OK when your settings are complete Gom Eon 4 SET DISPLAY BOARD ID y 1 Select proper ID number 2 Click OK button ID fu 5 FUNCTION INTERFACE 1 Up Counter Model 109 2 Up Down Counter Model 110 zoja Jali He tetCon Funzicns Hep ak tiom Functors def Mcde 109 Upto rter Moda 1 0 _p oan Canler Display Board ID ico vl Dizjlag Ruca ID Mm El Pim kosi Th m il Cmm y R SPECIFICATIONS 4 COUNTER VIEWING DISTANCE lt 131 Feet 40m DIMENSION 16 7 424mm Width 5 4 137mm Height 1 8 45mm Depth DISPLAY DIGIT 4 POWER INPUT DC12V CONSUMING POWER 9 Watts H 2 3 COUNTER VIEWING DISTANCE lt 75 Feet 23m DIMENSION 10 8 274mm Width 3 5 89mm Height 1 9 47mm Depth DISPLAY DIGIT 4 POWER INPUT DC12V CONSUMING POWER 9 Watts For indoor use only Avoid outdoor storage Keep away from high temperatures humidity dew water and direct sunlight Always disconnect power cord and other cables by holding plug Clean with damp cloth only 1M062160010
4. he ID two ASCII characters yyyy the preset number 4 ASCII characters lt STX gt lt xx gt lt RE gt lt ETX gt lt STX gt lt xx gt lt IN gt lt ETX gt Reset the Counter Increase the Counter by 1 xx denotes the ID two ASCII characters lt STX gt lt xx gt lt DE gt lt ETX gt Decrease the Counter by 1 xx denotes the ID two ASCII characters lt STX gt lt xx gt lt UP gt lt ETX gt Begin to count up lt STX gt lt xx gt lt DN gt lt ETX gt Begin to count down lt STX gt lt xx gt lt RE gt lt ETX gt Reset the Counter SOFTWARE SECTION 1 SOFTWARE SCREEN lolxl Fie zetZom Functions Help Model 1NA Hr Paunte mm xi 7 Select Model Model 109 Up Co nter Model 110 Up DownCounter I Show this window when progam staris Cancel 2 SET UP CONNECTING THE CABLE 1 Connect Display Board to the PC using RS232 RS485 cable 2 On the back of your computer identify a COM PORT If you have trouble locating a COM PORT on your computer please reference your computer user manual or contact the manufacturer of your computer 3 Connect the 9 Pin connector end to the COM PORT you will be using If the 9 pin connector is not connected to the correct COM PORT computer communication will not work RS232 RS485 3 CONFIGURE SOFTWARE EE 1 Select COM port I COM Por om x S
Download Pdf Manuals
Related Search