Make Wiring Connections Mount the VAM Insert an SD/SDHC
Contents
1. return to the SMTP server page and verify the email settings The VAM displays Warning Email sending failed Please check SMTP settings If this is the case check the security settings for the email chosen through the provider Adding Z Wave Devices EXISTING NETWORK NOTE Z Wave products from other manufacturers can be included added into the VAM network Z Wave devices that are always powered can serve as repeaters regardless of manufacturer To add include Z Wave devices verify the device is properly installed log onto home screen then do the following 1 Press Automation gt Z Wave Setup gt Add Device 2 Press the Function Key on the device follow the on screen messages until Device added successfully NOTE Refer to the manufacturer s instructions for proper installation procedures Do not use any garage door automation with any garage door opener that lacks the safety features required by U S federal safety standards this includes any garage door opener model manufactured before January 1 1993 A garage door opener L that cannot detect an object and stop and reverse the door does not meet current U S federal safety standards Your garage door opener also must signal before unattended door operation For more information please consult your garage door opener manual Defaulting the Z Wave Controller To remove all Z Wave devices do the following 1 Press Automation gt Z Wave Setup to display the2. Z Wave Device Management screen 2 Press Z Wave Default to delete all devices from the controller 3 Select Yes The following message is displayed This Z WAVE controller is about to be factory defaulted and will NOTE IF SYSTEM DEFAULT IS PERFORMED If VAM lose all devices in the enrolled list is reset to Factory Defaults the controller will assign a All Z WAVE devices must be re enrolled after this reset new network ID All Z Wave devices must be re included Each device will have to be excluded before it can be re into the system even if they appear on the Device List enrolled Remove all Z Wave devices first then re include all Yes or No desired devices see Adding Z Wave Devices section Changing Z Wave Device Names and Icons To change the icons do the following 1 Press Automation gt Z Wave Setup to display the Z Wave Device Management screen 2 Press Z Wave device to be edited 3 Choose the icon to represent the device NOTE This applies to Binary and Multilevel switches only X Light Bulb Light Switch Garage Door Sprinkler Pool Water Faucet Strobe Window Siren Sounder Fan Using VAM as a Secondary Controller VAM can be used as a secondary controller when connected to another Z Wave network NOTE If VAM is configured as secondary controller it cannot be used with Total Connect Remote Services 1 Remove any Z Wave devices previously included in the VAM 2 Press Automation gt Z Wave Se
3. any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e If using an indoor antenna have a quality outdoor antenna installed e Reorient the receiving antenna until interference is reduced or eliminated e Move the radio or television receiver away from the receiver control e Move the antenna leads away from any wi
4. down for more than 5 seconds to clear e Shipping Storage 40 F to 158 F 40 C to 70 C Button the VAM s Wi Fi network connection You then need to reconnect the VAM to your Wi Fi network Factory Default Reset Double press Program the Control Panel for use with VAM this button then while the green blue and yellow LEDs blink in sequence At the control assign an appropriate touch screen AUI type device press and hold down this button for more address ECP address for VAM and set a partition if applicable than 5 seconds to set the VAM to its e Refer to the control s programming instructions for detailed factory default settings procedures NOTE Do not use VAM s Console Mode to program the control e After enabling the VAM device address in the control set the VAM to the selected address See the Program Device s ECP Address section NOTE The default address in the VAM is 1 e Changing the VAM s ECP address after initial installation will cause a reboot during this process the VAM will be inaccessible On VISTA Plus series or equivalent Use data field 189 to enable an unused device address 1 2 5 or 6 for the VAM Addresses 1 and 2 are enabled by default On VISTA Turbo and Commercial VISTA Series VISTA 128BP 128BPT VISTA 128FBP 128FBPT etc Use 93 Menu mode to enable an unused device address e For older controls under Rev 10 addresses 1 2 and 3 30 may be used e For VIS
5. for Z Wave scenes End User License Agreement EULA The end user license displays and gives you the option to skip or accept the EULA Choose the option to display the home page NOTE This option reappears during initial installation or after a factory default of the unit Program the VAM Device Address Default VAM device address 1 1 Press Setup gt System 2 Press ECP Address Using the Up Dn arrows choose the device address assigned for VAM in the control panel 3 Press Apply 4 The VAM automatically reboots after the device address is set Note The Primary RIS option is only selected if the customer is NOT using Total Connect remote services Enabling can cause unpredictable results Set the Time amp Date Get Time Date from the Control Panels Press Setup gt System gt Time Date Setup gt Verify the time is set in the control panel gt Get Time Note Some older Commercial panels do not support the get time feature Set Up Email Notification Users and or the installer can receive email notifications when one or more selected system events or conditions occur NOTE Email notification requires that the user has an active email address and note the disclaimer at the bottom of the page Email notification is strictly for convenience use only Avoid relying on this feature for life critical events It is not UL certified and may fail at any time without notice 1 Press Setup gt E Mail 2 Pre
6. must face you NOTES e Avoid touching the contacts on the card e 4GB SD card supplied e Supports up to 16GB SD SDHC Card See Software Upgrades section for details on automatic updates mx INSERT SD CARD Front Panel LEDs FUNCTION Power Status Indicates power status Honeywell Green e Blinking when it is powered up and booting SD SDHC Card Slot e Solid green when it is fully functional Power Status LED Network Status Indicates Wi Fi Status Green Blue e In normal operation the LED blinks when p piney Status LED VAM is booting Operation Status LED e Solid blue when VAM is ready as AP Yellow mode acting as an Access Point or Reset Button connects to the internet as station mode Oe STA mode STA mode is when the Default Button VAM is connected to the Wi Fi router only internet access may be available but the VAM disables all remote access Specifications Operation In normal operation the LED is normally off Width 7 58 192 5mm Status Yellow e It will blink slowly when there is no ECP Height 5 31 135 0mm including ECP error or Z wave Depth 0 53 13 45mm controller not responding Voltage 12VDC e Fast blinking indicates Z wave is in Current 180mA enrollment or deletion status Humidity 93 RH non condensing Temperature Wi Fi amp e Wi Fi Network Reset Press and hold e Operating 14 F to 131 F 10 C to 55 C Factory Default
7. Honeywell NOTE Visit www MyWebTech Honeywell com for the full Installation and Setup Guide VAM VISTA Automation Module Installation amp Setup Guide Introduction VISTA Automation Module herein referred to as VAM combines home automation and home security The VAM s features allow integration with VISTA installations to support Z Wave devices is intended for use with compatible VISTA series controls The VISTA Automation Module also supports Remote Services for controlling Z Wave devices and Scenes remotely from an associated Total Connect account or port forwarding option VAM is controlled using a web browser on a Wi Fi enabled smart device such as a Tablet PC laptop Smartphone etc VAM Features e Built in Web Server e Wi Fi and LAN Connectivity e Z Wave Technology e Honeywell Total Connect Remote Services Compatible Supports up to 32 IP Cameras 4 viewable at one time DISPLAY NOTE For optimum viewing of the screens and menus the tablet s font size setting may need to be adjusted Make Wiring Connections The VAM connects to the controls keypad data ECP terminals using the provided 4 wire keypad harness TO CONTROL PANEL ECP TERMINALS ai J J BLACK GREEN REFER TO THE CONTROL PANEL S INSTRUCTIONS FOR MAXIMUM WIRE LENGTHS vam 003 V1 4 WIRE CONNECTOR HARNESS Wire Connections to the Control Panel Mount the VAM Verify that VAM and oth
8. TA Turbo series controls Rev 10 and higher addresses 1 30 may be used These addresses are normally not defaulted for AUI type devices If using Remote Services Enable an appropriate RIS address in the control and verify the option is enable the in the control s programming e On VISTA Plus Series panels below revision 10 the second digit of field 91 must be enabled with a 2 On panels with revision 10 or higher the RIS option is automatic and not necessary to enable e On VISTA Turbo Series controls choose the device address to set to RIS and enter a device type of 12 NOTES e These options MUST match how the AlarmNet Communicator is programmed e Z Wave scene programming requires RIS enabled to assign different triggers and actions Quick Arming Options In PC or Mobile View when user presses arm Away Night Stay they will be prompted to enter a user code If Quick Arming is enabled a user code is not required Refer to the control s installation instructions for enabling the Quick Arm feature NO Initial Setup The initial set up of the VAM is performed in 3 steps 1 Choose the Language 2 Connect to the Wi Fi network 3 Collect user data and giving the VAM a name Language Settings Upon power up the first option is to select a language This also occurs after a factory defaulting the unit NOTE This can also be changed later by accessing pressing Setup gt Language The VAM can display one of 4 languages En
9. a list of all your Z Wave devices with an enable or disable option This enables or disables those chosen devices from appearing on the Total Connect 2 0 account Compatible Z Wave Devices Z Wave devices may vary follow the instructions in the online Installation Guide or User Guide provided for installation steps Door Locks Yale Real Living Push Button Lever Deadbolt Lock Yale Real Living Touchscreen Lever Lock YRL220 Yale Real Living Touchscreen Deadbolt lock YRD220 Schlage Link Deadbolt Lock BE369 Schlage Link Lever Lock FE599 Schlage Touchscreen Deadbolt BE468 BE469 BE469NX Kwikset Smartcode Lever lock 912 Kwikset Smartcode Deadbolt Lock 910TRL 910CNT 914TRL Kwikset Smartcode Touchscreen Lock 916TRL Thermostats Honeywell Z Wave Thermostat ZWStat Wayne Dalton Zwave thermostat Appliances HomeManageable Appliance Module Intermatic Wayne Dalton Small Home Settings Small Appliance Module HM AM001 GE Wireless Lighting Control Plug In Appliance Module Lights Leviton ViziaRF Switches VRPA2 1LW Leviton ViziaRF Dimmers VRPD3 1LW Leviton ViziaRF Plug in Modules ZRP15 GE Wireless Lighting Control Dimmers 45602 ZW4101 GE Wireless Lighting Control Switches 45602 ZW3101 GE Wireless Lighting Control Plug in Lamp Modules Wayne Dalton HomeSettings Lamp Module HAO3 Trane Zwave Thermostat TZMT400AB32MAA TZMT400BB32MAA Radio Thermostat Co
10. be viewed from the customers remote service account Settings are defaulted for Honeywell AlarmNet IP Cameras changing the model Number will not automatically adjust to the cameras correct settings Refer to the cameras setup utility to gather this information software Upgrades System Information To view the current software version installed on your system do the following Press Setup gt System Info Automatic Software Updates To receive automatic remote updates an SD card with a minimum of 200mb available space is required When an update is available the system will automatically update the system NOTES 1 After a software upgrade it is recommended that you delete your browser s Temporary Internet Files cache Undesired operation may occur if these files are not deleted 2 Upon next login to the VAM an End User License Agreement EULA will be prompted Press Accept then proceed to using the VAM as normal IMPORTANT This menu is intended for the installer only and should not be changed by the user See the Full Installation and Setup Guide for more information Set Up Remote Access Account Setup Remote access lets the user access the VAM s menus directly via the Internet when away from home The home router must first be configured for port forwarding Refer to the router s instructions for details on port forwarding NOTE When using VAM via remote access the System HTTP API link will not display To se
11. button to enter camera information manually 2 To edit camera information select the camera name and press the Edit button Enter required information and then press Save Manual Camera Setup 1 Connect an Ethernet cable to the back of the camera LAN connect the opposite end to the Ethernet port on the router NOTE A LAN connection is initially required and once configured the Camera WIFI P will change from a LAN to Wi Fi Apply power to the camera wait for initial power up press Multi Media gt Camera Setup Enter the camera details below AUN Camera Name Camera Model Camera IP Address or URL RTSP Streaming URL MJPEG Streaming URL Mobile Streaming URL RTSP Real Time Streaming Protocol Port HTTP Port Resolution Options are 160x120 320x240 640x480 Frame Rate Ranges from 1 30 Frames Per Second NOTES e In general VAM is designed to support cameras with the following features UPnP for camera discovery on LAN RTSP streaming MPEG4 H 264 and Onvif for streaming on the VAM MJPEG for streaming to browsers 6 NOTE Every camera manufacturer makes their cameras slightly different so it is not a guarantee that VAM will work with every camera that supports the above network and codec features e Maximum number of enrolled cameras cannot exceed 32 with only 4 viewable at any one time NOTE If using Total Connect 2 0 remote services only Honeywell AlarmNet IP cameras with a maximum of 6 have the capability to
12. er connected devices do not exceed the control s Aux Power output capability If it does use a supplementary power supply as shown IMPORTANT When VAM is powered from an auxiliary power supply always apply power to the control panel first and then VAM Failure to observe this sequence results in improper operation of VAM and may result in an ECP Error indication POWER FROM SUPPLEMENTARY POWER SUPPLY IF USED SUPPLEMENTARY 12 VDC POWER SUPPLY PN ADI 2612 CONTROL TERMINAL STRIP AUX AUX DATA DATA IN OUT YELLOW pwr_supp_conn 011 V0O Supplementary Power Connections VAM is for indoor use only and should be mounted near the control or a keypad connected to the control for ease of wiring NOTE If using Z Wave devices the best practice is to enroll a device see Adding Z Wave Device Section and position the VAM in centralized location to confirm best Z Wave reception VAM mounts to a wall surface by hanging on two screws See the diagram to the right e Leave the screw heads 1 8 above the wall surface e f necessary drill a hole in the wall for the wire harness to pass through e Connect the wire harness to the VAM before mounting Refer to controls installation instructions for correct data ECP terminal connections MOUNTING SCREW DRILL 3 16 DIA HOLES 2 PLACES vam 004 VO Mounting Diagram Insert an SD SDHC Memory Card When inserting the gold contacts on the card
13. glish default Espa ol Portugu s Fran ais Once you have selected the language press Save at the bottom of the page or Next Wi Fi network Configuration To set up the Wi Fi network for the VAM the following is needed Wi Fi enabled smart device Tablet PC laptop Smartphone etc VAM SSID and WPA2 password located on the VAM s label VAM default IP address 192 168 2 1 Home router SSID and WPA2 password typically located on the home router s label home router must use WPA2 encryption and have a password key assigned e The initial configuration for connecting to the VAM and retrieving a local IP address requires internet access to the local area network LAN NOTES e Before setting up the network set your smart device for Wi Fi operation only turn off 3G 4G option e f the wireless router is later replaced these steps must be repeated to connect the VAM to the new router e If SSID is lost contact technical support at 800 645 74924 e f AP only mode is desired press Skip on the bottom of the page to skip the Wi Fi Setup 1 Connect a smart device to the VAM a Power up the VAM K b Connect the smart device s Wi Fi to VAM using the device s Wi Fi settings menu VAM is a wireless access point C Enter the VAM SSID VAM_xxxx SSID is case sensitive NOTE xxxx the last 4 digits of the MAC address d Enter the Key found on the VAM and labelled WPA2 key 2 Connect the VAM to the ho
14. me router a Open a web browser on the smart device b Enter the VAM s default IP address 192 168 2 1 into the browser on your smart device c Enter the home routers SSID and security key SSID and security key are case sensitive d press Connect A 1 minute countdown begins and displays The device is connecting to Network A Name please keep this page open Go to Wi Fi setup and select the Network Name access VAM 005 VO point and return to this page During this time a new network IP address is assigned to the J VAM a Note If you have trouble connecting please follow the onscreen instructions and retry the connection i process If using DHCP option confirm the router is connected to the internet If using Static IP Router option verify an IP address is available e When completed the VAM connects to the assigned router and displays the User Data Screen 3 User Data Screen This page collects the user s data Enter the data or press Skip to continue to the VAMs home page Zip Code Mobile Number E mail ID NOTES Router e This page can be accessed from the home page by pressing Setup gt User Profile e The data for Region and Zip Code Postal Code synchronizes to the Time Date setup page if completed during the initial setup e The e mail address synchronizes to the e mail setup page if completed during the initial setup e The Zip Code option is needed for the sunset sunrise
15. mpany of America CT100 CT32 Trane Zwave Thermostat TZMT400AB32MAA TZMT400BB32MAA Current Innovations Touch Screen CI 300E Garage Door Module Linear Z Wave Garage Door Opener Remote Controller GDZ00Z 4 Water Valves Fortrezz Wireless Z Wave Water Valve WV 01 NOTE The listed companies above may manufacturer multiple Z Wave devices Installing like modules not included on this list may produce unpredictable results These devices have not been confirmed to be compatible Adding Cameras The VAM supports up to 32 cameras IMPORTANT Connect cameras only when accessing VAM via the home router network and follow the camera s instructions for mounting 1 To add a camera to VAM it must be initially connected via an Ethernet cable even if the camera is wireless After a wireless camera is added the Ethernet cable can be removed a Connect an Ethernet cable to the back of the camera LAN connect the opposite end to the Ethernet port on the router b Apply power to the camera wait for initial power up c Press Multi Media gt Camera Setup d Press the Discovery button to locate the camera The screen displays an in progress message NOTE For best performance set video resolution to 320 x 240 at 8 frames per second Normal quality e Maximum suggested camera resolution 640 x 480 e Maximum suggested frame rate 15 fps e If the camera information is not discovered automatically press the Add
16. nces Radio L antenne s utilis e pour cet metteur doit tre install e une distance de s paration d au moins 7 8 pouces 20 cm de toutes les personnes Z Wave devices are identified by the Z Wave logo and can be purchased from your local retailer Z Wave is a registered trademark Sigma Designs Inc and or its subsidiaries SUPPORT amp WARRANTY For the latest documentation and online support information please go to https mywebtech honeywell com For the latest warranty information please go to www honeywell com security nsc resources wa MyWebTech Honeywell HI iiil 2 Corporate Center Drive Suite 100 P O Box 9040 Melville NY 11747 Copyright 2014 Honeywell International Inc 800 15858V2 3 15 Rev B
17. re runs to the receiver control e Plug the receiver control into a different outlet so that it and the radio or television receiver are on different branch circuits e Consult the dealer or an experienced radio TV technician for help Industry Canada Class B Statement This Class B digital apparatus complies with Canadian ICES 003 Cet Appareil num rique de la classe B est conforme a la norme NMB 003 du Canada FEDERAL COMMUNICATIONS COMMISSION FCC PART 15 This device complies with Part 15 of the FCC Rules and RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Cet appareil est conforme a la partie 15 des r gles de la FCC amp de RSS 210 des Industries Canada Son fonctionnement est soumis aux conditions suivantes 1 Cet appareil ne doit pas causer d interf rences nuisibles 2 Cet appareil doit accepter toute interference re ue y compris les interf rences causant une r ception ind sirable RF EXPOSURE WARNING The VISTA Automation Module VAM must be installed to provide a separation distance of at least 7 8 in 20 cm from all persons and must not be co located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi transmitter product procedures Mise en Garde Exposition aux Fr que
18. ss User SMTP to select the email provider SMTP establishes the email server s domain the from Security Disarm Away Secured End of Exit Arm address Stay a From the drop down menu select the email Zones Alarm Trouble Restore provider Gmail Outlook Yahoo or Add New Thermostat Temperature Above and Below b Enter the email ID user name and password Door Lock an rLock Locked Unlocked gt o c The Email Server and SMTP port number fields Toor or Doked wu nleKee l y A Garage Door Closed Opened Operation Disabled Failed are automatically populated unless Add New wae ceeded Water Valve Closed Opened d If Add New was selected enter the appropriate SMTP and port number information see your email provider for details e Press Save 3 Select the email addresses that will be notified when event types and conditions occur a Press Event 1 to define the event types and conditions that will trigger notifications to the chosen email address es b There are 4 events Each event will allow you to send to 4 separate emails Choices for email notification options include Security Zone Thermostat Door Lock Garage Door and Water Valve c Press Save and you will get a response that says Notification Save Success 4 Repeat step 3 for Events 2 4 if desired Troubleshooting If an error is returned through the listed SMTP email provider stating that the email has blocked a sign in attempt
19. t up a remote access log in do the following 1 Press Setup gt Account 2 Enter the desired user name and password Passwords must be a minimum of 8 alphanumeric characters and must include at least one uppercase one lowercase and one number 3 Enable local access authentication will prompt the user to enter a user name and password This allows them to gain access to the VAM when connecting using the local IP address NOTE If the user forgets the password or one does not exist they can always locally access the VAM within 20 minutes of power up 4 Press Save The new user is displayed To clear a user s login Press the CLEAR icon NOTES e Remote login is blocked after 3 failed attempts To reset remote access you must connect to VAM locally via the home router then re enable remote access Press Setup gt Account then press the appropriate user Enable icon and press Save e Port 443 is the fixed port assigned to the VAM and cannot be changed It is a secure login procedure the URL must begin with HTTPS then the external IP address If not you may receive an error of There is a problem with this devices security certificate e For an external dynamically assigned IP address using a DYNDNS can prevent troubles logging in due to the external IP address changing Refer to the DYNDNS provider for set up instructions FEDERAL COMMUNICATIONS COMMISSION FCC AND INDUSTRY CANADA IC STATEMENTS The user shall not make
20. tup to display the Z Wave Management screen press Z Wave Default and press Yes 3 Press the Z Wave Primary icon to switch the VAM to a secondary controller The Z Wave Primary icon changes to Z Wave Secondary accordingly 4 Start the inclusion process at the other network s primary controller see controller s manual then press the Add Device icon in the VAM s Z Wave Management screen To remove exclude VAM from the primary controller start the exclusion process at the primary controller then press the Remove Device button in VAM NOTES e Some manufacturers have software that can configure the network If this is the case after all devices are enrolled in the network you must learn in the VAM as a secondary controller to import all the devices over to the VAM Once this is complete you can switch roles to primary This is done by accessing the role shift option on the primary controller and on the VAM by pressing Setup gt System gt Z Wave advanced Setup gt Z Wave Secondary Controller Shift to Primary When VAM is configured as secondary it cannot be used with Total Connect 2 0 Integrating Total Connect 1 Pressing the Diagnostic Connect icon in the bottom left corner will test the AlarmNet server s connection status If the test has failed check your network connection 2 Verifies the Z Wave status if enabled it will communicate Z Wave status to Total Connect 2 0 Pressing the TC icon will populate
Download Pdf Manuals
Related Search