iSense - Isotera
Contents
1. S N 74 d a Ei On ST 1 i rilmia 4 iLir 1 Se EA Soe f gt a f EN S Ve TORORO The iSense sensor integrates PIR light sensor and controller functions in a compact unit for use with the Isotera LED lighting HFAC power distribution system It provides e PIR Movement sensor e Daylight detection e Light Level Maintenance and control Dimming control of iCouplers luminaires e On off control of iCouplers luminaires e Presence Absence detection Auto ON Auto OFF Manual ON Auto OFF Modes e Provides Interface for multiple switch dimmers See SIM data sheet e Provides control of the Power Hub PH user control port See Power Hub data sheet e BLUE connector Provides control of a zone It writes dimming levels on the 0 10V control line and reads commands from the Command line There can only be one BLUE Plug device connected to a zone e RED connector Reads the 0 10V Control line and writes commands on the Command line There can be multiple RED Plug devices connected to a zone e WHITE connector Sets up a special zone that writes to separate arrangement of command and control lines In this case the control line can be used only to signal the ON OFF states auxiliary OFF and does not provide 0 10V dimming drive The command line generates a coded ON OFF signal intended for use in soft on off control of the Power Hub see definition of Port CO2. 2 Light Level Maintenance EN to maintain the light level preset by the user e don t know what this means Switch on to enable the orientation mode whereby dimming below a preset level is inhibited 3 Orientation Night Light Lis still labl Controls Luminaire ON OFF control is still available MNN Light level setting P oul E peg User _ a Switch on to inhibit manual dimming from switch dimmers Use this to prevent users from overriding or cancelling configuration settings This rotary control is used to prevent PIR triggering Tanner avanti preset dimming levels in Light Level Maintenance for example e 1 to 30 minutes rotary Exit Timer with if there is sufficient ambient light or to set the automatic 5 minute session extend timer target level for Light Level Maintenance It can be Switch on to enable a unique slave mode that allows some of the control and command function of one zone to 5 Enable RED Plug response 5 to 1000 Lux level rotary setting disabled entirely if required be linked in e Blue red and white plug provide different OC 7 a B f If this switch is on the Auxiliary OFF signal is active on the WHITE plug Use this to generate an additional system control and functionality 6 Enable auxiliary OFF controlled zone that has simple ON OFF functionality in response to PIR or switch activity Switch on to ignore external PIR sensors The default mode is to allow inp
3. 11 iLink 3mtr Cabl TIPE PAR o 2004 108 EC Electromagnetic Compatibility Directive 2 way 50mm 2 way T piece with 50mm lead 2006 95 EC Low Voltage Equipment Directive Tech nN ical Data 3 way 50mm 3 way T piece with 50mm lead 2002 95 EC RoHS P Envi 2002 96 EC WEEE ower nvironment Extender Inverted coupler Consumption 50mW Max Normal Operating Temperature Range 10 C to Input voltage 5 5 to 7V 40 C Fixi n M al Nominal Operating Temperature 20 C 5 aterials a All materials are fire retardant low smoke and Ai aiin ai i Push in seli retaining ene cooing By et convection Ceiling hole diameter 40mm E ET Aporommatel adem Pam CityU ARE Don canaensing Minimum ceiling panel depth 18mm y Installation Category The device operates to IP20 adapter collar is available for thinner panels The specifications contained herein are believed to be correct at the time of publication and are subject to change without notice 7 Suite B Oakpark Business Centre Alington Road St Neots Cambridgeshire PE19 6WA United Kingdom Copyright Isotera 2013 All rights reserved ISS UK 100913 1 conta ctless power for LE D light ng 3 IS O te ra t 44 0 1480 476939 e info isotera ccom w www isotera com i
4. for output definition ITS e Plug and Play Check if we can use these words No mains wiring Flush fit less than 60 mm deep for shallow ceiling voids Single RJ11 cable provides power signalling and control system e Same sensor can act as master and slave e Many user settings See user manual Same sensor can act as master and or slave Easy to insert and remove without damage to ceiling tiles gt Light weight contactless power for LED lighting 3 isotera Suite B Oakpark Business Centre Alington Road St Neots Cambridgeshire PE19 6WA United Kingdom t 44 0 1480 476939 e info isotera com w www isotera com SS UK 100913 1 Se N se Multi functional sensor that integrates PIR light sensor and controller functions in a compact unit Se N se Multi functional sensor that integrates PIR light sensor and controller functions in a compact unit Indicators Pir Detection Area Configuration Switches e RED LED indicates PIR activity l F Sanaa Insert graphic we don t have a suitable No Switch Name Function e GREEN LED used in set up and commissioning graphic for publication ask Panasonic Manual On Auto OFF Enable Presence Absence selection If the switch is in the on position the Manual On Auto OFF mode is activated else Auto ON Auto OFF is activated Sessions agaa Switch on to enable the Light Level Maintenance function whereby the unit will attempt to dim luminaire output 17
5. ut from the PIR sensors of other 7 Inhibit External PIR response connected iSense devices PIR Slave mode It is especially useful to prevent Slave PIR response from a RED Plug enabled iSensor Exit Time Setting Switch on ignore the internal PIR sensor Use this to split PIR and Light Level control of a zone or zones over several This rotary control is used to set the value of a re triggerable timer in the approximate range of 1 to 30 8 Inhibit Internal PIR response iSensors for example minutes It is re triggered by PIR or switch activity and can be set to continuous if required Note that this does not prevent PIR signals being available externally There is also an unique Session Extension Timer feature whereby luminaire outputs are dimmed to a low level at the end of the Exit Time period Part Numbers Com pliance for a further 5 minute period during which the a Exit Timer may be re triggered by PIR or switch kaa pay Raabe Description The integrity of these references to be checked for before publication EN 61547 1996 Equipment for general lighting purposes EMC immunity Int Blue Switch Interface Blue requirements activity This usefully signals the imminent cessation of luminaire output and is especially useful in the Manual ON Auto OFF mode Int Red Switch Interface Red EN 55015 2006 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment 3mtr RJ
Download Pdf Manuals
Related Search