Oregon Scientific Breaking Dawn Sunrise Clock User Manual
Contents
1. RESET 1 Remove and reinsert the batteries 2 Press RESET to return to the default settings SPECIFICATIONS TYPE DESCRIPTION MAIN UNIT LxWxH 257 x 199 x 140 mm 10 12 x 7 84 x 5 51 in Weight 386 g 13 6 oz without battery FM 87 5 to 108 MHz Power Input AC 230V 50Hz EU version Input AC 100 120V 50 60Hz US Canada Japan version 2 x UM 4 AAA 1 5V batteries for backup NOTE Connection type of the switch E Range of lamp load Lamp 20W 60W The apparatus shall not be exposed to dripping or splashing To be completely disconnect the power input the mains plug of apparatus shall be disconnected from the mains The mains plug of apparatus should not be obstructed OR should be easily accessed during intended use No naked flame sources such as lighted candles should be placed on the apparatus TROUBLESHOOTING The below table lists out some of the problems you could encounter If you are unable to solve the problem contact the Customer Care Centre in your country Contact us via www2 oregonscientific com service support asp Problem Possible cause Solution Remarks The unit does not work Power supply Ensure plug has been properly inserted into the wall socket Ensure there is no power failure Check by connecting another appliance to the wall socket functions the unit does not respond The unit does not Normal use This is normal as the light bulb generates heat2. However work ensure there is enough ventilation and vents are not covered as this can pose a fire hazard When setting Normal use Press RESET at the base of the unit or remove and reinsert plug into wall socket The appliance will then be reset to factory default settings The light does not work Light intensity is too low Alarm function disabled Light bulb is defective Light bulb not properly screwed in Press Oto increase light intensity Ensure alarm time is displayed on LCD screen Press ALARM to enable Replace the light bulb Unscrew and screw in the light bulb again Lamp does not turn on again immediately after it has been switched off Normal operations Allow 3 seconds for the lamp to dim Please wait until the lamp reaches the preset intensity level No sound when the alarm goes on Alarm function disabled Radio is defective Ensure alarm time is displayed on LCD screen If is displayed press ALARM to enable If radio has been selected for alarm mode check that radio works Press RADIO after you disable the alarm or press ALARM The radio is defective produces a crackling sound Positioning of external antenna Broadcast signal is weak Change position of external antenna if necessary Press RADIO TUNEP to search for the correct signal Alarm did not activate today but it did yesterday Alarm function disabled Power failure Ensure al
3. RADIO OFF will be displayed on screen To activate deactivate soothing sounds 1 Press NATURE SOUND to play sounds 2 Press NATURE SOUND repeatedly to select desired sound 1 4 or to turn sound off To adjust volume Press when radio or nature sound is turned on TIP Press and hold to rapidly adjust volume ALARM To setthe alarm 1 Press SET ALARM to enter setting mode 2 Press to change the settings or press and hold to rapidly change the settings 3 Press SET ALARM to confirm and move to next setting 4 Repeat steps 2 3 for all setting options The settings order is time alarm sound select from beep I radio bird sound NOTE If radio alarm is selected radio will play for 60 minutes at set alarm time at maximum volume level If bird sound alarm is selected bird sound will gradually increase in volume to maximum and play for 2 minutes at set alarm time To activate deactivate alarm Press ALARM indicates alarm function has been disabled To silence the alarm Wave your hand up to 8 cm 3 inches in front of the SNOOZE SENSOR to silence it for 8 minutes 3 KJ will continue flashing to indicate snooze function has been activated EN EN To activate deactivate wake up light Slide WAKE UP LIGHT switch to ON OFF When wake up light has been activated will be displayed next to ALARM on the LCD screen NOTE Light will fade in gradual
4. first time use take out provided light bulb and go directly to step 2 1 Unplug unit from wall socket and allow unit bulb to cool for approx 15 minutes CAUTION Always allow unit to cool for 15 minutes prior to cleaning storing replacing parts as unit can be very hot 2 Turn the unit around to view back of the product UNLOCK COVER tab facing you 3 Using left thumb press and hold UNLOCK COVER tab 4 While continuously pressing on UNLOCK COVER tab place right hand around the side of the product Push in the side of the cover area above tab and hook and lift up to release cover Left handed individuals can use right thumb and left hand if more comfortable 5 Unscrew old light bulb 6 Screw in new light bulb 7 Holding cover with the top part at a slight angle away from you align the 2 front plastic tabs to the allotted space 8 Tilt cover down and towards you until lamp cover clicks back into place NOTE This unit uses 60 W light bulbs The built in protection feature will automatically shut down the unit when the temperature inside the lamp cover is too high Remove the power plug from the socket and only plug in again after unit has cooled down sufficiently IMPORTANT Please allow this unit to cool until the temperature inside is within a safe range Memory backup 1 Remove the battery compartment cover 2 Insert the batteries 2xAAA matching the polarities 3 Replace the battery compartme
5. reduce the hours 1 Lamp Holder 2 SNOOZE SENSOR Motion sensor for snooze function 3 Adjust volume only when radio nature sound is playing change values of the setting 4 SLEEP View remaining time enable sleep function with radio nature sound light set sleep timer 5 4RADIO TUNE P Enable auto search for radio station adjust radio frequency marginally by 0 05MHz 6 NATURE SOUND Toggle through selection Crickets Brook Ocean Rain 7 SET CLOCK Enter clock settings 8 SET ALARM View alarm status enter alarm settings 9 Adjust brightness only when LAMP function has been activated 10 LAMP Turn on off light 11 ALARM Enable disable alarm function 12 RADIO Turn on off radio 1 Battery compartment 2 WAKE UP LIGHT ON OFF Enable disable light for alarm sequence 3 DISPLAY BRIGHTNESS LOW HIGH Select LCD display brightness LOW HIGH 4 AUDIO LINE IN Socket for connecting to external music storage device 5 RESET Reset unit to default settings AM PM 1 2 a Beep kw Radio EN Bird chirp alarm selected 3 Alarm with wake up light enabled 4 Q Batteries low no battery 5 Alarm time 6 Radio Mode is ON and frequency is displayed 7 8 9 1 Volume is displayed Sleep mode is ON and remaining time is displayed EFE Nature sound selected 1 4 0 ET Sound from external source plugged into unit GETTING STARTED For
6. that interference will not occur in a particular installation If this equipment does cause harmful interfer ence to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The following information is not to be used as contact for support or sales Please call our customer service number listed on our website at www oregonscientific com or on the warranty card for this product for all inquiries instead We Name Oregon Scientific Inc Address 19861 SW 95th Ave Tualatin Oregon 97062 USA declare that the product Product No WS902 Product Name Sunrise Wake Up Clock Manufacturer iPM Concepts Limited Address Block C 9 F Kaiser Estate Phase 1 41 Man Yue St Hung Hom Kowloon Hong Kong is in conformity with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation
7. Orecon SCIENTIFIC Sunrise Wake up Clock Model WS902 USER MANUAL Orecon Sunrise Wake up Clock Model WS902 USER MANUAL CONTENTS Contents Introduction Overview Front View Bottom View LCD Display Getting Start Replacing Lamp Connect to Power Source Alarm with Wake up Light Sleep Timer Reading Lamp Play Music Spectifications Main Unit Troubleshooting Precaution EU Declaration of Conformity About Oregon Scientific OOOUARRRRARARRROOOOOOONNNNNNN EN EN INTRODUCTION Thank you for selecting the Oregon Scientific TM Sunrise Wake up Clock Our body clock is often not in sync with the demands and rhythm of modern life Our biological clock is affected by external cues such as sunlight Light at dawn stimulates production of cortisol which gets the body ready to work and wake up By simulating dawn Oregon Scientific s Sunrise Wake up Clock WS902 prepares the body to wake up by gradually increasing brightness to the set level in the 20 minutes prior to desired set alarm time Start your day better and feel energised to tackle the day Wake up as nature intended NOTE Please keep this manual handy as you use your new product It contains practical step by step instructions as well as technical specifications and warnings you should know about IMPORTANT of sleep needed OVERVIE This device does not
8. arm time is displayed on LCD screen If is displayed press ALARM to enable Perhaps there was a power failure which lasted longer than the capacity of the back up system The display will show an incorrect time and alarm will be 00 00 Do settings again The light wakes me too early late Location of unit is not suitable It is recommended that the unit is not placed too far and not lower than your head while in a sleeping position Make sure the light is not blocked by bed duvet or pillow Snooze does not work Distance Wave your hand in front of the SNOOZE SENSOR at a distance range of approx 1cm to 8cm 0 5 to 3 in LCD backlight is too weak to see Display brightness Slide DISPLAY BRIGHTNESS to HIGH There is no sound after plugging to an external source External device Connection Make sure external device is playing Make sure cable is firmly connected with the external device and the unit EN EN PRECAUTIONS Do not subject the unit to excessive force shock dust temperature or humidity Do not cover the ventilation holes with any items such as newspapers curtains etc Remove dust regularly with a dry cloth Accumulated dust poses a potential fire hazard Do not immerse the unit in water If you spill liquid over it dry it immediately with a soft lint free cloth Do not clean the unit with abrasive or corrosive materials Do not tam
9. egonscientific com service support asp For international inquiries please visit www2 oregonscientific com about international asp E CE amp Roms COUNTRIES RTTE APPROVAL COMPLIED All EC countries Switzerland Ep and Norway N gt ABOUT OREGON SCIENTIFIC Hereby Oregon Scientific declares that this Sunrise Wake Up Clock Model WS902 is in compliance with EMC directive 2004 108 EC A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service FCC STATEMENT This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer ence in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee
10. ly increase in brightness to maximum 20 minutes prior to set alarm time Light Will stay on even after SNOOZE has been activated after set alarm time for 60 minutes SLEEP TIMER To adjust sleep timer setting 1 Turn on desired option OPTION PRESS Radio RADIO Light LAMP Nature sound NATURE SOUND 2 Press SLEEP to activate 3 Press SLEEP repeatedly to change the sleep timer setting 120 90 60 30 15 0 min After 5 seconds of inaction the timer will automatically be confirmed and set TIP Press SLEEP again to change sleep timer 120 90 60 30 15 0 min NOTE Ensure radio or sound and or light has been selected to activate sleep timer NOTE If light option has been chosen for sleep timer light will fade out READING LAMP To turn on off light Press LAMP To adjust level of brightness e Press O 6 to increase or decrease brightness TIP Press and hold O 6 to rapidly change level of brightness 1 20 For your convenience the level of brightness will be stored in memory for the next time reading lamp is turned on NOTE Do not look directly at the light PLAYING MUSIC Using a cable plug one end to your music storage device and one end to AUDIO LINE IN located at the back of unit When cable has been successfully connected will be displayed on the LCD screen and sound will emit from speakers LCD BACKLIGHT To adjust brightness Slide DISPLAY BRIGHTNESS switch to LOW HIGH
11. nt cover NOTE Batteries should not be exposed to excessive heat such as sunshine or fire Before selecting a location to place the unit consider the following Ensure there is approximately 15 cm between unit and closest object such as walls or other objects Ensure there is at least 40 cm space above the top of the unit for ventilation purposes e Ensure distance between unit location and wall socket is not longer than the power cord itself Batteries serve as a back up power supply To fully utilize all features plug into wall socket To completely disconnect from power the unit should be disconnected from the wall socket NOTE The main unit should not be exposed to wet conditions No objects filled with liquid such as vases should be placed on the main unit CLOCK 1 Press SET CLOCK to enter setting mode 2 Press or to change the settings or press and hold to rapidly change the settings 3 Press SET CLOCK to confirm and move to next setting The settings order is 12 24 hr format time RADIO To activate deactivate radio Press RADIO to turn radio on off To set radio station 1 Press RADIO to turn radio on 2 Press and hold RADIO TUNEP to auto search or press RADIO TUNE to manually select frequency For your convenience the volume and radio frequency will be stored in memory for the next time radio is turned on SOOTHING NATURE SOUNDS NOTE Deactivate radio first
12. per with the unit s internal components This invalidates the warranty Only use fresh batteries Do not mix new and old batteries Images shown in this manual may differ from the actual display e When disposing of this product ensure it is collected separately for special treatment e Placement of this product on certain types of wood may result in damage to its finish for which Oregon Scientific will not be responsible Consult the furniture manufacturer s care instructions for information e The contents of this manual may not be reproduced without the permission of the manufacturer Do not dispose old batteries as unsorted municipal waste Collection of such waste separately for special treatment is necessary Please note that some units are equipped with a battery safety strip Remove the strip from the battery compartment before first use NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice NOTE If the external flexible cable or cord of this luminair is damaged it shall be exclusively replaced by manufac turer or his service agent or a similar qualified person in order to avoid hazard NOTE For indoor use only EU DECLARATION OF CONFORMITY Visit our website www oregonscientific com to learn more about Oregon Scientific products If you re in the US and would like to contact our Customer Care department directly please visit www2 or
Download Pdf Manuals
Related Search