LED wireless alarm system(plastic)
Contents
1. 1 2 3 A o POWER 4 5 6 v O 7 8 9 SET Q ALARM F 0a A ENT 2 nro Confirm Program Record Emergency Back Space Number Esc Disarm 3 Specifications Operating power 9 15VDC Static current lt 60MA e Alarm current lt 380mA Away Home Power Llight Alarming Light Lower Voltage Recording Light Play o o BE ANT POWER IN TEL OUT ON OFF ON i In Out Mic Battery Wired siren Antenna Power Recording on off Operating environment Temperature 10 50 Humidity lt 80 Maximum available quantity of keychain remotes 8 PCS e Maximum available quantity of wireless sensors 60 PCS o Dimensions 180 120 38 mm Rechargeable battery Ni Mh 4 8v 600mAh up to 8hrs long e Speaker siren 100dB built in 4 Type and definition of Defense Line Types of Defense Line and what they mean 1st Defense line Indicates the first detecting defense areas or the perimeter zone such as doors and windows This is the perimeter or areas where thieves initiate when attempt to break in These zones are generally composed of wireless door magnet sensors and wireless curtain PIR sensors 2nd Defense line Indicates the second detecting defense areas areas such as living room aisles and bedrooms hall ways a2. CONTENTS User s Manual Foreword amp Main Features amp Brief introduction of the Product Understanding of Alarm Host Specifications Type and definition of Defense Line Programming the alarm host To setup Alarm ID Number AUN G How to change User code operation 6 Understand and Configure Wireless Accessories o Wireless Keychain Remote e Wireless Door Magnet Wireless wide angle PIR Sensor 7 LED wireless alarm manufacture default setting 8 Wireless default zone code chart 9 Common Problems and Solution 10 Daily Maintenance and Care Thank you for purchasing and using LED intelligent wireless home alarm system This is a Hi tech household security product It will make your life safer and colorful Please read the below information carefully before using for a proper usage Brief introduction of the Product A Product components This product is composed of alarm host basic accessories and optional accessories Alarm Host Basic Accessories Optional Accessories Jl j OL ra IU e bea na k ie l e ae a 7 NG Keychain wireless wireles wide angle gasalam smokealarm remote a remote door sensor HR sensor LED Alarm Host 3 ppa p i wirel curtain Wireless GSM auto dialer PIR sensor indoor siren Wire less outdoor siren Wireless keypad B Representative models M o de INO A larm ing W ay Com ponents 80 88 E O
3. light will appear solid red Note The XX indicate group number of the 2nd defense zones including zone 11 through zone 15 Press the Learning Emitting Switch twice consecutively to trigger PIR sensor the alarm host will beeps in series and the e Learn light will flash five times and then turns off to indicate the motion sensor 25 has been successfully added To Cancel e Press SET User code ENT then e 71 ENT XX ENT The alarm host will beeps then the Learn light will flash once and then turns off to indicate the PIR motion sensor has been successfully cancelled Note The alarm host can only learn 1 wireless device Wireless Wide Angle PIR Motion Sensor at a time a total of 4 wireless devices PIR Motion Sensors to a zone group can be added For example for the 2st defense line if 4 sensors were to be added to zone group 11 through zone group 15 it total 20 sensors in all If 1 device is removed from the group of 4 devices then all 4 devices in that same group will be automatically removed and each device s will have to be added again to the alarm host 7 LED wireless alarm manufacture default setting 26 Defense Defense Bypass Delay Time to Compatible Remark Zone Code Zone Type Zone Alarm Accessories 00 to 01 No No Wireless Support Keychain up to 4 remote amp sensors Wireless per zone Keypad 01 to 05 24 hour No No Wireless Smoke Support
4. enter User code of host gt beep gt enter O 5 beep and the host will then automatically hang up after last beep to 16 successfully complete the operation Alarm dialing mode After the alarm host triggered or goes off the alarm host will starts to dial the first enlisted telephone number then the second third fourth and so on Unless any of the enlisted telephone numbers answers otherwise this routine auto dial will continues for three times Alarm priority If the telephone line is busy when the alarm host goes off the alarm host will take priority and it will automatically cut off the busy used line to resume automatic dial to the enlisted alarm telephone numbers to convey the crime Telephone line disconnection Alarm Alarm Sounds if PhoneLine is Cut or comes off the hook the host will beep every 5 seconds after the telephone line are cut off or disconnected It will continue to beep until the phone line are fixed or reconnected AWAY mode In this state after any detection in the 1st 2nd or 24hrs defense line is triggered the alarm host will immediately sound the sirens and at the same time automatically dial the enlisted alarm telephone numbers in sequence 17 Home mode In this state after any detection in the 1st or 24hrs defense line is triggered the alarm host will immediately sound the sirens and at the same time automatically dial the enlisted alarm telephone numbers in sequence In HOME
5. To Playback the recorded voice message greeting Slide the switch on the left side of the alarm host to DC ON press and hold the playback button to playback 13 the recorded voice message greeting One key Arm By keychain remote Press the AWAY All Alarm or the HOME Part Alarm button on the remote control to arm and the alarm host will beep once to confirm the operation is successful See Wireless Remote Controller page for more detail By Keyboard on alarm host Press AWAY All Alarm or the HOME Part Alarm the alarm host will beep once to confirm the operation is successful See 2 Understanding of alarm host page for more detail One key Disarm By Keychain remote Press the DISARM button on the remote control to disarm the alarm and the alarm host will beep twice to confirm the operation is successful By Keyboard on alarm host Programming Password ENT Press the button follow by the User code and then ENT to disable alarm siren using the alarm host The host will beep twice to confirm the operation is successful Emergency Panic Distress 14 By Keychain remote Press the EMERGENCY HU button on the keychain remote at times of an emergency to immediately activate the sound siren on the alarm host and wireless sirens By Keyboard on alarm host Press the EMERGENCY KU button on the alarm host at times of an emergency to immediately activate the siren sound on the alarm host and wireless sirens
6. prevent system failures and resolves problems in time 5 Check batteries in all wireless sensors and replace them as needed to ensure normal operation 6 Power off and remove all batteries from all wireless system before storing them on shelves 32
7. the Learn light will flash once and then turns off to indicate the Keychain remote has been successfully cancelled e Note The alarm host can only learn 1 Keychain remote at a time a total of 8 Keychain remotes can be added to a host Wireless Door Magnet La a iF a Pa Functions Features Mainly detect open close Door states of doors and windows generally set as a 1st Defense Line or perimeters If any doors or windows are opened it will transmit the alarm signal to notify the alarm host Specifications Operating power 23A 12V alkaline battery Wireless Transmitting distance 2450ft in open area Service life s2 years Alarm Distance 5 4cm installation and Usage Mount the magnet or smaller piece onto the door in a position of about 5 6ft above the ground to prevent any child ren from pampering with it Use the included mounting bracket if the door and the door frame are not flush Mount the emitting or larger piece onto the door frame ensure the magnet piece and the emitting piece are flush or in parallel The spaces between the two shall be less than 10mm in gap Replace the batteries if the red LED light flashes frequently 21 Adding and Cancelling Door Window senor To Add Press set User code ent then 7 O ent 00 ent gt The Learn light will appear solid red Note The XX indicate group number of the 1st defense zones including zone 06 through zone 10 Trig
8. D Y TA 8 0 88 E OD W TA G SM E OD Y TA G SM E O DW TA Main Features gs LY SPP J je ge m Er 2 e Easy to use and cost effective D I Y do it yourself wireless intruder alarm system kit Supports up to 60 wireless sensors 15 wireless defense zones and 4 wireless sensors per zone Transmit at 430 433MHz frequency band wireless transmitting distance up to 300 5 feet Keychain remote smoke sensor amp siren and up to 450 feet magnetic door window sensor amp PIR motion sensor Can dial up to 5 phone numbers in sequence Arm disarm the system by Main Host Keypad Wireless Keypad Keychain remotes or even remotely by phone Available in both ACIDC with low voltage Indicators Programmable silent alarm or audible alarm Recordable alarm voice message up to 9 seconds record time Telephone line disconnection alarm sound every 5 seconds Smart 3 defense lines configuration 1st defense line is the perimeter 2nd defense line for in room amp 24 hour defense line Internal rechargeable backup battery in alarm host last up to 8 hours Battery alkaline included for keychain remotes wireless door sensor and wireless motion sensor last up to 2 years Remembers programming settings when power is disconnected Ademco CID compatible protocol 2 Understanding of Alarm Host
9. Defense Alarm Wireless up to 4 Line Gas Alarm amp sensors Panic button per zone 06 to 10 1st Defense No No Wireless Door Line Magnet amp Wireless Curtain PIR 11 to 15 2nd Defense No No Wireless Wide Line Angle PIR Motion Sensor PA Wireless Sensor Type The default Defense Zone Code Keychain Remote 00 Wireless Door Window Sensor 06 Wireless Wide Angle PIR Motion Sensor 11 Wireless Curtain PIR Sensor N A 12 Wireless Gas Alarm N A 02 Wireless Smoke Alarm 01 9 Common Problems and Solutions Problems Possible Cause The alarm host sounded off immediately after connecting the power The telephone incoming line has not been connected not well connected or short circuit Double check test and secure the incoming telephone line or use other standard phone to test the line to ensure working status 28 The alarm host cannot record or partially records The record switch is not turned on The record buttons not presses down and hold while attempting to record or not held down all the way Slide the record switch to the ON position Securely press and hold down the RECORD button during recording Speak up close to the rear speaker of the host Repeatedly receiving the alarm telephone Failed to operate according to the operation instruction of the telep
10. Telephone alarm After receiving the phone call from the alarm host the recorded voice message will repeatedly plays for 22 seconds Before the 22 seconds expires one of the following action must be take place A Press the number 8 on the phone pad to extend the time intervals for an additional 20 seconds to enter the listening state In the listening state the built in microphone on the alarm host will be active to pick up any sound that takes place near the alarm host 15 B Press the pound button to immediately replay the recorded voice message C Press the star button the host will end the call and stop to dial the enlisted alarm telephone numbers Note the is required to use in order to stop the alarm host from continuing to dial the next enlisted telephone numbers D Hang up the telephone without any command the host will end the call and automatically continues to dial the next enlisted alarm telephone numbers ARM remotely by phone 30 seconds after successfully dial the telephone number of alarm host there will be a beep enter User code of host gt beep gt enter 1 gt beep and the host will then automatically hang up after the last beep to successfully complete the operation Note Arm remotely by phone requires the alarm host to be armed or in the Away mode DISARM remotely by phone 30 seconds after successfully dial the telephone number of alarm host there will be a beep
11. ails groups below 01 Group 1 reserved for CID Protocol number for management center not for 10 personal numbers 02 Group 2 personal telephone number 03 Group 3 personal telephone number 04 Group 4 personal telephone number 05 Group 5 personal telephone number 06 Group 6 personal telephone number Delay time to Arm XX ent Setup a dwell time in which the alarm will become activated or armed Enter 10 for XX to setup Delay Time to Arm for 40 seconds enter 15 to setup Delay Time to Arm for 1 minute and press the ENT button to confirm The default setting is 10 or 40 seconds alarm dwell time Delay time to Alarm XX ent Setup a dwell time in which the alarm will sound or trigger Enter 20 for XX to setup immediate alarm sound triggering enter 21 to setup a 15 seconds Delay Time to Alarm The default setting for Delay Time to Alarm is 20 Emergency Alarm Voice XX ent Enter 30 for XX to disable Emergency Alarm Voice enter 31 to setup audible alarm The default is 31 11 Alarm voice for 1st and 2nd defense line XX ent Enter 40 for XX to disable alarm voice for 1st amp 2nd defense line enter 41 to enable Audible alarm The default is 41 Telephone Disconnection Alarm XX ent Enter 60 for XX to disable Telephone Disconnect Alarm enter 61 to enable Telephone Disconnect Alarm The default is 61 To upload arm disarm to management center XX ent Enter 50 to disable upload
12. e operation instruction of Adding and Cancelling sensors devices of newly added wireless sensor s Follow the operation instruction of Adding and Cancelling to activate the new wireless sensor s The PIR motion sensor flashes frequently in green Battery is drained or low Replace with new battery of the same voltage specification The door window sensor indicator flashes frequently in green after alarming Battery is drained or low Replace with new battery of the same voltage specification The distance of the keychain remote gets shorter Battery is drained or low Replace with new batter of the same voltage specification 10 Daily Maintenance and Care 31 This alarm system is hi tech with outstanding design and sophisticated product which should be used carefully To make the alarm system operable in long terms and to stably prolong the service life the follow are strongly recommended 1 Installed alarm system and alarm host in the dry and well ventilated places 2 Do not put the alarm host and any wireless sensors in cold hot or dusty places to prevent it from shortening the life of electric parts preventing the plastic shell from distorting and accelerating to age 3 Do not install the wireless alarm system in low easy to reach and exposed places to prevent the children from pampering with or thieves easy access 4 Regular scheduled testing is necessary to help
13. e alarm host 23 It is immunity to pets cats dogs etc that are less than 10KGS will not cause false alarm specifications Operating power 9V alkaline battery Wireless Transmitting distance 2450m in open area Service life s2 years Detection Area 110 1010m installation and Usage Mount the bracket to a desired wall surface location or corner at a height of about 6ft to 7ft above the ground Open the sensor cover and connect the 9VDC battery Next refers to the diagrams above to adjust and select the Jumper Line timer between 5S or 5MIN for the motion sensor to detect once every 5 seconds or the sensor to detect once every 5 minutes Recommended to use 5S for testing and default SMIN for normal use Skip below to add motion sensor for newly added motion sensor before closing the sensor cover and proceed to the next step 24 Match the grooves of the sensor to the bracket and slide the motion sensor down from top to bottom to secure e Adjust the sensor to a proper angle and then slide the power switch located on the side to the ON position The motion sensor takes 30 seconds to become active for operation normal working state after switching ON e A red light will flashes for motion detection a frequent green light flashes mean it is time to replace the battery Adding and Cancelling PIR motion sensor To Add e Press set User code ENT then 70 ENT XX ENT The Learn
14. enter 51 to enable upload to management center The default setting is 50 or disable Leave this disable if management center is not in service Alarm ID Number 80 ent XXXX ent Enter an integers between 0000 9999 for XXXX to setup Alarm ID Number for management center The default is set as random apply to management center use only To setup Alarm ID Number SET 999999 ent 80 ent enter Alarm ID Number ent Press SET button the programming LED will light on enter 999999 press ENT then input a 12 new Alarm ID Number press ENT to complete the Alarm ID Number change Notice the programming LED light will disappear after the final ENT is pressed How to change User Code SET 999999 ENT six Digital New User Code ENT six Digital New User code ent Press SET button the programming LED will light on enter 999999 press ENT then input a new six digital user code press ENT re input the new six digital user code and then press ENT to complete the user code change Notice the programming LED light will disappear after the final ENT is pressed operation e To record a voice message greeting Slide the switch on the left side of the alarm host to the RECORD ON press and hold the Microphone button speak close into the rear side speaker of host and then release the microphone A when finish with voice message greeting Voice message greeting can be anywhere between 0 9 seconds long e
15. gers the Door Window magnet twice consecutively the alarm host will beeps in series and the Learn light will flash five times and then turns off to indicate the remote control has been successfully added To Cancel Press set User code ent then 71 ent 00 ent The alarm host will beeps then the Learn light will flash once and then turns off to indicate the keychain remote has been successfully cancelled Note The alarm host can only learn 1 wireless device Magnet Door Window Sensor at a time a total of 4 wireless devices magnetic sensors to a zone group 22 can be added For example for the 1st defense line if 4 sensors were to be added to zone group 06 through zone group 10 it total 20 sensors in all If 1 device is removed from the group of 4 devices then all 4 devices in that same group will be automatically removed and each device s will have to be added again to the alarm host Wireless wide angle PIR Functions Features oO oO NI Power Switch Down Off w V Ligh I Up On O Ka Learning Emitting Switch Mainly monitor and control e9 Jump Line Fix the PIR by pushing indoor stereoscopic space generally set as a 2nd o a a ua BA uy g Defense Line When human body enters the detection areas the motion sensor will transmit the alarm signal to th
16. hone alarm After answering the alarm phone calls and hearing the recorded message pls advanced to telephone Alarm page of this user s manual as a reference to try to resolve this problem The alarm host does not sound the alarm after the detector triggered the alarm in armed mode 1 Caused by the functions of armed Away or Armed Home 2 Have already setup time for Entry Delay or Exit Delay 1 In Armed Home mode make sure the sensor or wireless devices triggering is notin the 2nd Defense Line 2 Ensure the sensor detectors are not active within the system setup Entry Delay Time or Exit 29 Delay Time The PIR motion sensor does not work Weak battery power not switched on or the PIR motion detector isin the power down mode Open the sensor shells to install the battery and slide the power switch to On Power down mode may be in affect 5S detect once every 5 seconds 5MIN detect once every 5 minutes please refers to the user s manual for PIR setup The detecting distance of PIR motion sensor gets shorter The ambient temperature in the detecting area is too high When the ambient temperature in the detecting area exceeds the human body temperature the detecting distance will 30 get shorter it s normal The alarm host does not alarm after the new added wireless detector is triggered Failed to follow th
17. mode the 2nd defense line will be disabled and cannot be triggered 6 Understand and Configure Wireless Accessorie Away Wireless Keychain Remote Functions Features Disarm e Used to armed amp disarmed alarm host Home Emergenc e Emergency button for emergency or lia panic help specifications e Operating power 27A 12V alkaline battery e Wireless Transmitting distance 2300ft in open area 18 Service life s2 years installation and Usage Ideal for keychain and to take it when the alarm host in set to AWAY mode Press the AWAY button to arm before leaving home or in AWAY mode and press the DISARM button to disarm Press the HOME button to part arm or 1st defense line enabling and protecting the perimeters of home at night time before going to sleep Please replace the batteries within 2 years of usage or any time when it becomes less sensitive or shorter controlling distance Adding amp Cancelling Keychain Remote To Add Press set User code ent _ then 70 ent 00 ent mummy the Learn light will appear solid red Press any button on Keychain remote twice consecutively the alarm host will beeps in series and the Learn light will flash five times and then turns off to indicate the keychain remote has been successfully added 19 To Cancel e Press SET User code ENT then 71 ENT 00 ENT the alarm host will beeps then
18. nd etc These zones are generally composed of the wireless wide angle PIR sensors where it can detect movements in open spaces 24 hour Defense line Indicates the detecting defense areas in a 24 hour monitoring statue commonly used in areas such as emergency distress medical rescue gas leakage and fire alarm and etc These zones are generally composed of panic button wireless gas sensors and wireless smoke sensors 5 Programming the alarm hos Function operation Operation Explanation Notes 1 The alarm host will automatically exit from the programming status if inactive for 9 20 seconds 2 Programming is effective after Start to program use ESC button to go to previous step 3 The alarm host will beep in series to indicate the operation is successful and beep twice to indicate operation failure set User code ent This command applies throughout whenever programming the alarm host before attempting to change other programming features such as Delay Time to Arm Delay Time to Alarm Emergency Alarm Voice Adding and Cancelling wireless devices and etc For example to change Delay Time to Arm below from default 40 seconds to 1 minute press SET 888888 ENT follow by 15 ENT The default of user code is 888888 6 digits long Input Alarm telephone Number XX ent telephone Number ent XX indicate telephone group number which can be of personal numbers or management center See det
Download Pdf Manuals
Related Search