location & removal installation location & removal installation
Contents
1. Pairing For detailed directions please see the TOOKI MB user manual Insert the vehicle key and wait for the Comand head unit to start if the unit does not pass the manufacturer logo or requires you to press the ON button then please check your optical connections When the Command head unit has fully started press the TEL button the bottom right of the screen should display Searching and an empty signal display Using the phone handset begin the Bluetooth pairing procedure Please see the handset user manual for detailed guidance and security settings When you have Tooki XXXXXXxX in your handset found devices list select and enter the pin code 6888 when asked When you are successfully paired the searching display should now say Ready and show your available service provider signal After a short time the phone book icon will be active with your loaded phonebook COMPATIBLE PRODUCTS Video In Motion Allow TV DVD to work in motion passenger use VIMCANMER 1 CL S SL Class VIMCANMER 2 E CLS SLK Class VIMCANMER 3 A B C CLK GL ML R Class Audio amp Video Input OPV 1 MER No TV Tuner models A B C CLK GL ML R Class OPV 2 MER With TV Tuner models A B C CLK GL ML R Class OPV 3 MER With Rear Camera Models A B C CLK GL ML R Class Auxiliary Audio Input MOST MOSTAUXMER All Mercedes models equipped with MOST OPTICAL TROUBLE SHOOTING If when entering the vehicle key2. the unit does not automatically turn on you should check your power connections and also your optical cables for the correct INPUT and OUTPUT configuration Also if you have removed a factory phone module ensure you have correctly connected the optical cables using the supplied joiner If when entering the vehicle key the unit freezes on the manufacturer logo you should check your power connections and also your optical cables for the correct INPUT and OUTPUT configuration Also if you have removed a factory phone module ensure you have correctly connected the optical cables using the supplied joiner If when pressing the TEL button the unit displays phone not available check all connections turn off the vehicle and remove the key Remove all plugs from the Interface re fit after a few moments and re test If you have an active paired handset but no phone book list please check security settings on the handset or see handset manual Note that the phone book will take up to 2 minutes to fully load in some cases depending on handset type If the TOOKI MB fails to pair or functions are not active please check the factory phone module has been disconnected from both power and optical connections If the handset you are using will not pair to the TOOKI MB please check that there are no other handsets paired at the time or that the maximum number of paired phones 6 is not reached Please see the TOOKI MB
3. LOCATION amp REMOVAL Firstly you will need to determine if your Command unit is equipped with a fac tory fit phone module as this will depend on location of fitting Press the TEL button if the message please insert phone appears then the phone module is present If the message phone not available appears then there is no phone module present If no Phone Module present Installation is made at the Command head unit All removal methods vary from vehi cle to vehicle all other models follow very similar procedures these models shown CLK C Remove the gear selector gaiter and pull the trim below it then remove two screws holding the ashtray and remove Next remove two more screws holding the panel below the command Pull the panels above and below the Command to expose the four screws holding in the unit ML R Open ashtray and remove two screws then close ashtray and remove Heater control panel can be pulled from bottom to re move Next take out two screws below unit and pull down the two silver locking bars shown opposite E CLS First remove the trim surrounding the gear lever Next remove the ash tray assembly Then remove the two screws holding the CD Chang er storage pocket E class located behind the ash tray and remove the unit Then locate the two screws that move the head unit locking tabs These are locat ed on the underside of the Command Unit head Unit These will need to be turned unt
4. OVAL If Phone Module present You will need to locate the phone module SLK located behind the boot back panel remove the carpet panel and all screws securing the metal panel The unit is mounted on the rear side of metal panel CLS located under the boot carpet at the front section of the boot inside the black plastic casing se cured with two bolts E Follow CLS ML located under the passenger side UK rear seat under the carpet cover The unit is mounted on the silver metal bracket GL Follow ML C Located on the Right Hand side of the boot be hind the right hand carpet trim The unit is mount ed on the reverse side of the metal bracket simi larly to the SLK picture SL Under the boot floor liner above the navi computer CLK Under the boot floor at the front almost up against the back of the back seats it is then under a black metal panel held in by a number of bolts INSTALLATION Using the same method as opposite you will need to remove the OUT optical cable and insert it into the OUT location of the optical plug supplied then insert the optical cable supplied into the OUT location of the factory plug Your Interface and Factory plugs should now appear as the picture below INTERFACE PLUG FACTORY PLUG OUT CABLE FROM FACTORY PLUG IN CABLE FROM FACTORY PLUG Plug in and mount the microphone in the required location plug in the optical plug and the power plug to complete the installation Basic use and
5. il they stop t these screws cannot be removed SLK Remove the gear selector and surround next remove two screws from behind the rubber stoppers in the ashtray and two screws also behind the rubber stoppers in the compartment above the Command head unit then remove both the ashtray and top compartment Finally remove four screws that secure the command head unit itself INSTALLATION Phone Module present The factory phone module shown below will need to be removed from its pow er and optical connection It is possible to then install the TOOKI MB at the Factory phone location using the optical directly from the phone module and using the 12v Permanent and 12v ground found in the 32 way plug The optical cable supplied is then not needed ETUE E N ar a ra al Se Dh E rik i Ensure you have sufficient length of supplied Microphone cable If this is not possible then installation will need to be made at the Command head unit see No Phone Module present Using the supplied optical Joiner to connect the optical cables from the Phone Module end to end to continue the optical loop shown below also leave the 32 way Phone module plug removed No Phone Module present With the Command head unit now removed locate the 12v permanent and 12v ground and the black optical plug Same as above in the Command head unit wir ing Take note of the two arrows marked on the optical plug LOCATION amp REM
6. user manual for instruction with deleting paired phones NAV TV TOOKI MB BLUETOOTH PHONE CONNECTION MOST ALL MERCEDES 2003 2009
Download Pdf Manuals
Related Search