Dexxo Pro io
Contents
1. clear all settings from the remote control refer to Keytis io remote control documentation change the system key memorised by the remote control Resetting all settings Fig 50 Press the SET button until the light goes out 7 s This clears all previously stored settings and retums them to their default values LOCKING PROGRAMMING Fig 51 Used to lock the programming settings end limit setting self learning setup Simultaneously press the SET and buttons start by pressing SET pressing and must take place within two seconds To access programming mode once again repeat the same procedure REFITTING COVERS Refit the motor head and built in light covers Fig 52 11 Operating codes displayed C1 Waiting for a command C2 Door opening C3 Waiting for the door to close C4 Door closing C5 Obstacle detection Displayed during obstacle detection then for 30 s C6 Safety input active Displayed after a movement request or during movement when the safety input is active This display is maintained as long as the safety input is active C9 Pedestrian door safety contact active Displayed after a movement request or during movement when the pedestrian door contact is open The display is maintained as long as the pedestrian door contact remains open Ca Safety mechanism self test Displayed during safety mechanism self tes2. 2 When replacing the light bulb select a 230 V 40 W E14 type Fig 3 Regularily check the operation of the door to identify any sign of wear deterioration or incorrect balancing Do not operate the door if repairs or adjustments are required Remain at a safe distance when operating the door In accordance with standard EN12453 concerning the safe use of motorised doors and gates the remote control of an automatic garage door which is not visible to the user particularly using the TAHOMA unit always requires a photoelectric cell type safety device to be installed on this automatic function Failure to comply with these instructions absolves SOMFY of any liability resulting from damage that may be caused 230 V 40W max PRODUCT PRESENTATION Description Fig 4 The Dexxo Pro system is designed to power garage doors in residential use This motor drive system comprises A motor head 1 with integrated light 2 and digital operating display 5 Arail assembly 3 with a manual release cord 4 OPERATION AND USE Normal operation Using Keytis or similar remote controls Open Fig 5 Stop Fig 7 General stop Fig 8 BIP BIP BIP BIP BIP BIP H 1 Using Keygo or similar remote controls Open Fig 12 Close Fig 13 Obstacle detection operation Fig 15 and 16 The detection of an obstacle duri
3. to the Public Programmable no effect or motion refused Adjustable sensitivity 4 levels Programmable partial re opening or full reopening Yes can be selected adjustable partial opening position Yes Programmable from 3 5 cm s to 18 cm s 10 possible values Programmable from 3 5 cm s to 18 cm s 10 possible values Programmable does not slow down short slowdown zone 30 cm long slowdown zone 50 cm Recording and accessing data Cycle counter cycle counter with obstacle detection number of radio channels stored history of the last ten defects recorded 1 Maximum load for motor to start and drive door for at least 5 cm according to RAL GZ definition Dimensions Overall length 3 295 3 895 Available travel 2 555 3 155 171 ef Fixation 2 982 3 582 Rail 2 900 3 500 Overall length 3 153 3 753 Rail 2 900 3 500 13 14 somfy com 5048554E HOME MOTION BY EN CONTENTS GENERAL PRESENTATION The world of Somfy Support SAFETY INSTRUCTIONS Standards Safety instructions PRODUCT PRESENTATION Description OPERATION AND USE Normal operation Special operation TROUBLESHOOTING Digital display Power outage PERIPHERALS MAINTENANCE Replacing the bulb in the light unit Checking Replacing a Keytis remote control battery Replacing
4. a Keygo remote control battery TECHNICAL SPECIFICATIONS SS oooo O CO o0 O0 on Ah LW ww C9 nm DD GENERAL PRESENTATION Thank you for choosing a Somfy product This product is designed and manufactured by Somfy in line with quality procedures that are ISO 9001 compliant The world of Somfy Somfy develops produces and sells automation systems for residential and commercial applications Alarm systems automatic blinds and shutters garage doors and gates all Somfy products are designed to fulfill your needs in terms of safety comfort and security At Somfy the quest for quality is a continual process Somfy has built its reputation on the quality of its products and is synonymous with innovation and technological leadership worldwide Support Getting to know you listening answering your needs is all part of the Somfy approach Please contact your local Somfy retailer or installer for details on other Somfy products Internet www somfy com SOMFY SOMFY SAS capital 20 000 000 Euros RCS Annecy 303 970 230 SAFETY INSTRUCTIONS Standards This product complies with the safety specific rules for powering vertically opening garage doors in residential use requirements standard EN 60335 2 95 When installed in line with these instructions and in compliance with the Installation Checklist the product will be compliant with standards EN 13241 1 and EN 12453 The instructions referred to in the Installation
5. exit the setup menu Press for 2 s start learning Press for 7 s clear learning and settings Stop learning Selecting a setting Modifying a setting value e Using the forced mode Q Start the learning cycle Confirm setting selection Confirm setting value End limit setting and self learning Fig 16 N For swinging doors change the P9 setting before starting self learning 1 Press the SET button until the light comes on 2 s The display shows S2 2 Control the motor using the or buttons so that the transmission system runner moves to link up with the trolley and closes the door Pressing and holding the button closes the door Release the button before the motor has time to force against the door Pressing and holding the button opens the door 3 Adjust the closed position using the or buttons Release the button before the motor has time to force against the door 4 Press OK to validate the closed end limit position and start the self learning cycle The door runs through a complete Open Close cycle If learning was correct the display will show C1 If the learning cycle was not completed correctly the display will show S1 During the learning cycle If the door is moving pressing any button will stop the movement and interrupt the learning mode If the door is stopped pressi
6. of channels that can be memorised Situoio 6 Others unlimited CONNECTIONS Safety input Type Dry contact NC Compatibility Photoelectric TX RX cells Reflex cell Sensor strip with dry contact output Pedestrian door safety input Dry contact NC Wired control input Dry contact NO Remote lighting output 230 V 500 W class 2 Orange light output 24 V 15 W with built in flashing control 24 V controlled power supply output Yes for possible photoelectric TX RX cell self test Safety input test output Yes for possible reflex cell or sensor strip self test Accessory power supply output 24 V 500 mA max Remote aerial input Yes lo aerial compatible R f 9013953 Backup battery input Yes battery pack compatible R f 9001001 Autonomy 12 hours 1 to 3 cycles depending on door Charge time 48 hours OPERATION Forced operation mode By pressing and holding the motor control button Lighting time delay after movement Programmable 60 s to 600 s Automatic closing mode Yes programmable closing time delay from 10 to 120 s Orange light pre warning Programmable with or without prior warning duration set to 2 s Safety input operation While closing Programmable Stop Partial re opening Full reopening Built in obstacle detection Operation when an obstacle is detected Preset partial opening command Progressive start up Opening speed Closing speed Closure approach speed Troubleshooting Before opening Dangerous Movement Area Accessible
7. to sequence at the end of the installation procedure or install a sensor 9 fastest speed approx 18 cm s bar If spurious detection of obstacles occurs when this parameter is By default 6 12 de sate d d PES approx 12iems modified end limit setting and auto programming will have to be carried out again P6 Partially open position Storing the position as illustrated in Fig 42 P7 Closure approach speed 0 no slowdown P7 0 the door does not slow before closure 1 short soft stop P7 1 the door speed slows 20 centimetres before closure 2 long soft stop P7 2 the door speed slows 50 centimetres before closure f this setting is changed it is essential to run the force measurement sequence at the end of the installation procedure or install a sensor bar f spurious detection of obstacles occurs when this parameter is modified end limit setting and auto programming will have to be carried out again P8 Opening speed 0 slowest speed approx 3 5 cm s f spurious detection of obstacles occurs when this parameter is to modified end limit setting and auto programming will have to be 9 fastest speed approx 18 cm s carried out again P9 Choice of operating direction 0 direction 1 all types of doors except If this setting requires modification the end limit setting must be type of door swinging doors repeated along with self learning 1 direction 2 swinging doors A0 Safety action prior to 0 no effect If value 1 is selected triggering the s
8. up and over door B Sectional door if the door s upper profile is a specific one use the sectional door mounting bracket ref 9009390 ifthe door surface exceeds 10 sq metres use the sectional door adapter ref 2400873 C Sideways opening sliding door for side wall mounting use a belt transmission rail an adjustable cranked arm ref 9014481 for ceiling mounting use an articulated arm ref 9014482 D Swinging door Use the swinging door kit ref 2400459 E Semi and non projecting door Use a high performance transmission rail the semi and non projecting door kit ref 2400458 Some doors of this type may prove impossible to automate Contact SOMFY s technical department Door dimensions Fig 3 For maximum door heights the motor travel can be optimised By installing the motor head at a 90 angle Fig 7 O By fixing the lintel bracket to the ceiling behind the lintel itself by up to 200 mm Fig 5 By cutting the link arm to size POINTS TO CHECK PRIOR TO INSTALLATION Preliminary checks Check the garage door can be operated manually and runs smoothly Ensure the door is in good mechanical condition pulleys mounts and is correctly balanced spring tension A Remember that any work performed on door springs may be dangerous The structure of your garage walls lintel inside surfaces cross members door rails are used to mount
9. 1153 Netherlands Somfy BV 31 0 23 55 44 900 Norway Somfy Norway 47 67 97 85 05 Poland Somfy SP Z 0 0 48 0 22 618 80 56 Portugal Somfy Portugal 351 229 396 840 Romania Somfy SRL 40 0 368 444 081 Russia cf Germany Somfy GmbH 7 095 781 47 72 Singapore Somfy PTE LTD 65 0 638 33 855 Slovak Republic Somfy Spol s r o 421 33 77 18 638 South Korea Somfy JOO 82 0 2 594 4333 Spain Somfy Espana SA 34 0 934 800 900 Sweden Somfy Nordic AB 46 0 40 165900 Switzerland Somfy A G 41 0 44 838 40 30 Syria Somfy Syria 963 9 55580700 Taiwan Somfy Taiwan 886 0 2 8509 8934 Thailand Somfy Thailand 66 0 2714 3170 Turkey Somfy Turkey 90 0 216 651 30 15 United Arab Emirates Somfy Gulf 971 0 4 88 32 808 United Kingdom Somfy LTD 44 0 113 391 3030 United States Somfy Systems Inc 1 0 609 395 1300 PATENTS AND DESIGN PATENTS PENDING FOR SOME COUNTRIES e g US Somfy SAS capital 20 000 000 Euros RCS Annecy 303 970 230 06 2011
10. 23 This function is used to move the door at any time remote control lost safety mechanism failure etc Remove the built in lighting cover Control door motion using the and buttons Pressing and holding the button will trigger closure Pressing and holding the button will trigger opening Operation after a power outage After a power outage the next time the door is moved it must be opened completely Always allow the door to open fully TROUBLESHOOTING Digital display The LCD display is situated under the lighting cover It provides motor operation status The main operating codes are as follows Code Description Comments C1 Waiting for a command C2 Door opening C3 Waiting for the door to close C4 Door closing C5 Obstacle detection Indicates that the door encountered an obstacle The display is maintained for 30 s after detection C6 Safety input active Indicates that an obstacle preventing door closure is present between the photoelectric cells or is in contact with the safety sensor bar installed on the door C9 Pedestrian door safety contact active Indicates that the pedestrian door within the garage door is open Door operation is inhibited Cd Working from back up battery Indicates that the main power supply to the motor is cut and that the motoris powered by the battery Waiting for a command back up pack If other codes are display
11. 3 Code keypad 8 Photoelectric cells 4 Keyswitch 9 Reflex type cells 5 Aerial 10 Sensor bar Electrical connections for the various peripherals Fig 30 to 39 Cut the electric power supply to the motor before performing any work on peripherals If the display remains off after working on the system check the wiring for possible short circuits or polarity reversals General electrical diagram Fig 30 Photoelectric cells Fig 31 It is compulsory to install photoelectric cells If automatic closing is activated P0 1 If the automatic function is controlled remotely not visible to the user Two types of connections can be made A Standard without self test program the setting P2 2 B With self test program the setting P2 1 This means that an automatic test is conducted to check photoelectric cell operation every time the door operates If the test fails no door movement is possible Reflex photoelectric cell Fig 32 With self test program the setting P2 1 This means that an automatic test is conducted to check photoelectric cell operation every time the door moves If the test fails no door movement is possible Sensor bar Fig 33 With self test program the setting P2 1 This is used to perform an automatic test of sensor bar operation every time the door moves If the test result is negative no door movement is possible AN Make sure you have correctly configu
12. Manual and Instructions for Use of this product are designed to ensure that damage to property and injury to persons is avoided along with compliance with the above standards Failure to comply with these instructions absolves Somfy from any liability for any damage that may be caused Dexxo Pro is a product that must be installed inside the garage with a built in back up control system Somfy hereby declares that the device is compliant with the essential demands and other relevant requirements of directive 1999 5 CE A declaration of compliance is available from the web site at www somfy com ce Dexxo Pro io This product is usable in the European Union and in Switzerland These are important safety instructions For safety reasons it is important to always follow all instructions Retain these instructions for future reference Safety instructions Every month test that the motor drive unit reverses its motion when it encounters an obstacle that is at least 50 mm from ground level If this is not the case call your installation specialist Always be very careful when using the manual release cord for a manually operated door may fall quickly due to weak or broken springs or if it is badly balanced Before manually operating the door or performing maintenance work always turn the power off and where necessary remove the battery Fig 1 Never let children play with door control systems Keep the remote controls out of reach of children Fig
13. N Always reengage the motor drive mechanism before sending another command to the motor drive unit Special operation Depending on the peripherals installed and the operating options set by your installer the Dexxo Pro system may perform the following special operations Using Telis Situo or Composio Fig 18 Safety photoelectric cell operation An obstacle detected between the cells will prevent the door from closing The door will stop and then completely or partially reopen depending on the setup selected during installation when an obstacle is detected during the close cycle The light will flash for 30 seconds during this process Pedestrian door safety function Opening a pedestrian door within the garage door will prevent the door from moving The light will flash for 30 seconds during this process Flashing orange light The orange warning light will flash every time the door moves A two second delay before the door starts to move can be selected during installation Remote lighting operation The light comes on every time the motor drive unit is operated The light will go out one minute after the door stops moving The time delay can be adjusted during installation Partial opening operation with a Keytis remote control If this option is selected Ashort press on the remote control button will partially open the door Fig 19 Along press on the remote control button will fully open the door Fig 20
14. The partially open position will only operate from the closed position BIP Partial opening operation with a Keygo remote control If this option is validated Pressing a remote control button programmed for partial opening causes the door to open partially Fig 21 Pressing the remote control button programmed for full opening causes the door to open fully Fig 22 The partial open position can only be achieved if the door is previously closed Automatic closure mode operation The door is automatically closed after a time delay set at the time of installation An additional command during this time will cancel the automatic closure and the door will remain open The next command will close the door Working from the back up battery If a back up battery is installed the Dexxo Pro motor will operate when a power cut occurs The following conditions apply to operation Door speed is reduced The light will not come on The safety devices are disabled Battery specifications Endurance The battery will last for 12 hours with a maximum of 1 to 3 operating cycles depending on the weight of the door Recharging time 48 hours Service life prior to replacement approx three years To ensure optimum battery life we recommend that the power to the motor is switched off and the door is operated for a number of cycles using battery power three times a year Forced operation mode Fig
15. This may take from a few seconds to around a minute depending on the number of products connected to the system 3 Briefly press the button chosen to control the Dexxo Pro motor The remote control sounds a confirmation beep and the Dexxo Pro motor s light blinks for five seconds Programming by copying a previously programmed Keytis remote control Completely copy the programming of a Keytis remote control Fig 22 This operation is used to copy all of the buttons programmed from an already programmed remote control 1 Press the PROG button on the previously programmed remote control until the green indicator comes on two seconds 2 Briefly press the PROG button on the new remote control Wait for the second beep and for the green indicator to start blinking rapidly a few seconds Individually copy the programming of a Keytis remote control button Fig 23 This operation is used to copy the programming of a single button from an already programmed remote control 1 Press the PROG button on the previously programmed remote control until the green indicator comes on two seconds 2 Briefly press the button to copy on the previously programmed remote control 3 Briefly press the PROG button on the new remote control Wait for the confirmation beep after a few seconds 4 Briefly press the button chosen to control Dexxo Pro on the new remote control It is impossible to program Keytis re
16. afety input will inhibit door opening safety ADMAP 1 movement rejected opening A1 Safety action during closure 1 stop Value 1 is not allowed when using a sensor bar on the safety input 2 stop partial re opening 3 fully reopen A2 Obstacle detection action 2 stop partial re opening during closure 3 fully reopen t0 Automatic closure time delay 0 to 12 time delay value value x 10 s 2 20s tl Lighting time delay 0 to 60 time delay value value x 10 s Remark Due to the thermal cut out protection system the integrated 6 60 s light may cut out automatically if it is used for an extended length of time We therefore recommend selecting a light time delay in excess of 2 mn t1 12 or 120s only when remote lighting is used Boldface text default values Programming example setting the P7 closure approach speed Fig 41 Setting up a long soft stop function zone P7 2 Special case adjusting the position of the door for partial opening Fig 42 Select setting P6 and validate by pressing OK Move the door to the desired partially open position Pressing and holding the button will close the door Pressing and holding the button will open the door Validate by pressing OK Exit the menu with SET Forced mode Fig 43 This function is used to move the door to a specific position Pressing and holding the button will close the door Pressing and
17. at you wish to use for full opening within 10 seconds The button for full opening has been memorised 10 SPECIAL OPERATION After a power outage the next time the door is moved it must be opened completely the motor must be stopped at the upper stop before it can start operating normally again For other specific operations see page 5 of the user manual CLEARING REMOTE CONTROLS AND ALL SETTINGS Clearing remote controls Fig 47 to 49 Clearing Keytis or Keygo remote controls Individually clearing a remote control button This can be done by programming from the Dexxo Pro motor Fig 21 Programming a previously programmed button automatically clears any previously stored programming settings by directly clearing the remote control only for Keytis remote controls Fig 47 Simultaneously press the PROG button and the BUTTON to be cleared on the remote control Clearing all remote controls Fig 48 1 Press the PROG button on Dexxo Pro until the light blinks seven seconds This will Clear the system key memorised by Dexxo Pro Clear the programming for all memorised remote controls 2 For Keytis remote controls repeat the direct clearing procedure for all of the Keytis remote control buttons programmed on the Dexxo Pro system Fig 47 Keytis remote control general reset Fig 49 Simultaneously press the PROG and KEY buttons This will perform a program general clear action all buttons
18. care when handling the motor drive system Never connect the mains power supply or the battery back up system before completing the installation process Never use high pressure water systems for cleaning purposes INSTALLATION Installation height Fig 4 Measure the distance D between the door s highest point and the ceiling If D is between 35 and 200 mm mount the complete system straight onto the ceiling If D exceeds 200 mm mount the complete assembly so that the height H falls between 10 and 200 mm Detailed description of installation steps Fig 5 to 15 Mounting the lintel bracket and the door bracket Fig 5 When installing the system directly onto the ceiling flush with the ceiling the lintel bracket can be mounted on the ceiling if necessary recessed from the lintel by up to 200 mm max Fig 5 O Assembling the two part rail Fig 6 1 2 3 Unfold the two parts of the rail A Ensure that the chain or belt is not twisted 4 Assemble the two parts of the rail using the sleeve 5 Mount the complete assembly using the eight mounting screws 6 Tighten the nut to tension the chain or belt The compressed rubber must measure 18 and 20 mm The mounting screws must not penetrate the rail do not drill When installing the system directly onto the ceiling do not use the sleeve mounting screws Fitting the rail onto the motor head Fig 7 Fitting the complete assembly onto the gara
19. des displayed Accessing stored data TECHNICAL SPECIFICATIONS Dimensions io homecontrol provides advanced and secure radio technology that is easy to install o io homecontrol labelled products communicate with each other improving comfort security and energy savings homecontrol www io homecontrol com o o O wm CO xau AY soon a A coc C9 coco C9 mih nn N GENERAL PRESENTATION This product complies with the safety specific rules for powering vertically opening garage doors in residential use requirements standard EN 60335 2 95 When installed in line with these instructions and in compliance with the Installation Checklist the product will be compliant with standards EN 13241 1 and EN 12453 The instructions referred to in the installation manual and instructions for use of this product are designed to prevent damage to property and personal injury along with compliance with the above standards Failure to comply with these instructions absolves Somfy from any liability resulting from damage that may be caused Dexxo Pro is a product that must be installed inside the garage with an integrated back up control system Somfy hereby declares that the device is compliant with the essential demands and other relevant requirements of directive 1999 5 CE A declaration of compliance is available from the web site at www somfy com ce Dexxo Pro io This product is suitable for use in the European Union and
20. ed contact your Somfy installer Power outage Following a power outage the motor must recognise its fully open position again Open the door fully using a memorised remote control The door will open at a degraded speed N Allow the door to open to the fully open position PERIPHERALS A number of peripherals are available Key Description Comments 1 Keytis4 io Hand held 4 channel remote control 2 Keytis 4 home io Hand held 4 channel remote control general closure function 3 Keygoio Hand held 4 channel remote control 4 Photoelectric cells To prevent door closure if an obstacle is detected 5 Orange light To signal a warning when the door operates 6 Keyswitch Keyswitch designed for use outside the garage 7 Battery For guaranteed operation even during a power break 8 Release lock To engage the manual release system from the outside using the existing door handle Highly recommended when the garage door is the only access point into the garage 9 Outside release lock 10 Door locking kit A system to reinforce door locking MAINTENANCE Replacing the bulb in the light unit Fig 25 1 2 Remove the light cover 3 4 Unscrew and replace the defective light bulb 5 6 7 Refit the light cover Use a 230 V 40 W E14 socket light bulb Checking The obstacle detection function Every six months check that
21. fety mechanism If value 0 is selected the safety input is not taken into account 1 safety mechanism with self test If value 1 is selected the system s self test is run at the start of every 2 safety mechanism without self test operating cycle If value 2 is selected the safety system runs without a self test it is essential to test its proper operation every six months P3 Obstacle detection 0 low sensitivity If this setting is changed it is essential to run the force measurement sensitivity 1 low sensitivity sequence at the end of the installation procedure or install a sensor 2 standard bar 3 high sensitivity P4 Partial opening cycle 0 not valid If the partial opening cycle is validated 1 valid For Keytis remote controls a short press on the remote control button causes partial opening along press on the remote control button causes full opening For Keygo remote controls Pressing the button programmed for partial opening causes partial opening pressing the button programmed for full opening causes full opening When this parameter is activated pressing a previously programmed remote control button will partially open the gate an additional command must then be performed so that the button fully opens the gate again refer to Programming Keygo io remote controls for full and partial opening operation PS Closing speed 0 slowest speed approx 3 5 cm s If this setting is changed it is essential to run the force measurement
22. ge ceiling Fig 8 to 10 Fitting to the lintel bracket Fig 8 Ceiling mounting Flush with the ceiling mount the system directly onto the ceiling using the rail Fig 9 It is possible to add mounting points at the motor head level Fig 9 O Hung from the ceiling two options mount the system at the motor head Fig 10 O mount the system at the rail Fig 10 To add an adjustable intermediate mounting along the rail or a mounting at a dimension h between 250 mm and 550 mm use the ceiling mounting kit ref 9014462 Fig 10 O Fitting the arm onto the door and the trolley Fig 11 1 Release the trolley using the manual release cord 2 Bring the trolley up to the door 3 Attach the arm to the door bracket and the trolley Adjusting and fastening the opening travel stop Fig 12 1 Release the trolley from the runner using the manual release mechanism and bring the door to the open position Do not open the door fully but position it so that it does not reach its own travel stop 2 Slot the travel stop 10 into the rail then turn it by 90 3 Position the travel stop against the trolley 4 Moderately tighten down the mounting screw Do not tighten the mounting screw all the way down Excessive tightening can damage the screw and cause the travel stop not to remain in place Fitting the chain retainer pads Fig 13 For chain rails only These pads are used to limit spurious noise
23. holding the button will open the door Programming a Situo Telis Composio Impresario type remote control Fig 44 Before programming the remote control make sure that it has already memorised the system key Refer to the corresponding remote control documentation 1 Press the PROG button on Dexxo Pro until the light comes on 2 Briefly press the PROG button on the remote control Wait for the Dexxo Pro light to blink This may take from a few seconds to around a minute depending on the number of products connected to the system Remark Dexxo Pro can memorise up to six Situo remote controls For other types of remote controls no limit applies PROGRAMMING KEYGO IO REMOTE CONTROLS FOR FULL AND PARTIAL OPENING OPERATION In order for the garage door to open fully and partially parameter P4 must be activated refer to the section entitled Parameter setting When parameter P4 is activated all the remote control buttons previously programmed during commissioning become programmed buttons to partially open the garage door An additional memorising command must be performed on buttons which are used to fully open the garage door The operations to be performed differ according to the desired function for the button being programmed full or partial opening and depending on the memorisation which has already been performed on the button prior to activation of parameter P4 Switch to full opening for a button
24. in Switzerland SAFETY INSTRUCTIONS Caution These are important safety instructions Always follow the instructions incorrect installation may lead to serious injury Safety instructions Before installing the motor drive unit remove all unessential lines or chains and switch off all equipment that is not essential for motorised door operation Before installing the motor drive unit make sure that the door is in good mechanical condition that it is properly balanced and that it opens and closes correctly Locate all control systems at least 1 5 metres above floor level making sure that they are visible from the entrance to the garage but safe from moving parts Position the manual release cord no more than 1 8 metres above floor level Where a removable release mechanism is used we recommend storing it close to the door Fix the label describing the manual release procedure close to the release mechanism Fix the warning labels describing the hazards of door motion close to any fixed control mechanisms installed and make sure that the labels are clearly visible to the user After installation make sure that the mechanism is correctly adjusted and that the motor drive unit reverses its motion when the door encounters an obstacle that is at least 50 mm from floor level After installation make sure that no part of the door overhangs an area accessible to the public After installation make sure that the motor drive unit inhibit
25. linked to chain friction within the rail Position each of the pads in the first hole in the rail after the travel stop Make sure that the pad is pressed in all the way so that its positioning pin is accessible outside of the rail Checking the chain or belt tension Fig 14 The rails are supplied ready tensioned and inspected If necessary adjust the tensioning N The rubber or tension spring must never be fully compressed during operation Connecting the mains power supply Fig 15 1 Remove the motor cover and the protective sheet 2 Fit the light bulb 3 Connect to the antenna 4 Connect to the mains supply supply must be suitably protected a fuse or circuit breaker with a 5 A rating and a residual current device 30 mA An omnipolar disconnection mechanism must be provided for the power supply by using a power cord with a mains splug that can be disconnected or by fitting a switch that ensures a contact separation distance of at least 3 mm for each pole refer to standard EN60335 1 Make sure that the manual release cord is located at a maximum height of 1 80 metres off the ground If necessary extend the cord Plug the power cable into a suitable power outlet that complies with electric power requirements The electric PROGRAMMING Programming button description Press for 2 s memorise remote controls le b o Press for 7 s delete remote controls Q Press for 0 5 s call up and
26. mote controls in the following cases The remote control has not memorised the system key A number of installation receivers are in programming mode Anumber of remote controls are in key transfer or programming modes Any incorrect programming is indicated by a series of fast beeps together with the orange indicator blinking on the Keytis remote control At this stage in the installation process the Dexxo Pro motor drive unit is ready to run Programming Keygo remote controls Fig 24 and 25 Each control button is programmed individually To clear a previously programmed button refer to the section entitled Clearing Keygo remote controls There are two ways to program the remote control Programming from a Dexxo Pro motor Programming by copying a previously programmed Keygo io remote control Programming from a Dexxo Pro motor Fig 24 1 Press the PROG button on the Dexxo Pro until the light comes on 2 seconds 2 Simultaneously press the outer right and outer left buttons on the remote control The remote control indicator light flashes 3 Briefly press the selected button to actuate the Dexxo Pro motor The light of the Dexxo Pro motor flashes for 5 seconds Programming by copying a previously programmed Keygo io remote control Fig 25 This operation is used to copy the programming of a previously programmed remote control button 1 Simultaneously press the outer right and outer left button
27. must be able to establish radio communication with an installation receiver Memorising the system key Fig 20 1 Set existing remote control no 1 to the key transfer mode With a Keytis Telis Impresario Composio remote control press the KEY button until the green indicator comes on two seconds With another remote control refer to its documentation 2 Briefly press the KEY button on the new remote control Wait for the confirmation beep a few seconds Programming the Keytis remote control Fig 21 to 23 Before programming the remote control make sure that it has already memorised the system key Each control button is programmed individually A button that is already programmed cannot be programmed on a second receiver To see if a button is already programmed press it button programmed green indicator comes on button not programmed orange indicator comes on To clear a previously programmed button refer to the section on Clearing Keytis remote controls There are two ways to program the remote control Programming from a Dexxo Pro motor Programming by copying a previously programmed Keytis remote control Programming from a Dexxo Pro motor Fig 21 1 Press the PROG button on the Dexxo Pro until the light comes on two seconds 2 Briefly press the PROG button on the remote control Wait for the second beep and for the green indicator to start blinking quickly
28. ng SET once will exit the learning mode You can call up the learning mode at any time even when the learning cycle has already been executed and the display shows C1 Keytis remote control description Fig 17a El Individual control buttons El General STOP button E General CLOSE button Keytis 4 home io only E Operation indicator light Mc On PA Intermittent cC Blinking H Low battery indicator light 3 Closing clip PROG button programming the transmitter EJ KEY button memorising the system key Keygo remote control description Fig 17b El Individual control buttons E Operation indicator light HE On X Intermittent c Blinking ij EN Fitting the battery for Keytis remote controls Fig 18 Programming Keytis remote controls Fig 19 to 23 then you must perform the Memorising the system key step before programming the remote controls Fig 20 If the Keytis io remote control to be programmed is the system s first remote control then go straight to Programming the Keytis remote control step Fig 21 to 23 If the installation already comprises other io homecontrol amp products with at least one programmed remote control only possible at the installation location To gain authorisation to transfer its system key or its programming the previously The operations for memorising the system key and to program a remote control by copying another Keytis remote control are IN programmed remote control
29. ng door opening will stop the door and cause it to reopen slightly to clear the obstacle Fig 15 When an obstacle is detected during the close cycle the door will stop and then reopen Fig 16 Once an obstacle has been detected the light will flash for 30 seconds Light operation The light will come on each time the motor drive unit is operated The light will go out one minute after the door stops moving Repetitive use that causes the light to be continually on may result in a thermal cut out this will automatically turn the light off Manual release cord operation Fig 17 Dexxo Pro is fitted with a manual release mechanism so that you can move the door manually should a power failure occur for example The manual release mechanism should be easily accessible and located no more than 1 80 metres above floor level 1 Disengaging the motor drive mechanism Pull on the manual release cord until the door drive mechanism is disengaged 2 Manually moving the door This is possible as long as the door drive mechanism is disengaged 3 Reengaging the motor drive mechanism Move the door manually until the drive mechanism comes to reengage itself into the transmission rail N When disengaging the motor drive mechanism use caution for a badly balanced door may cause sudden door movement that may be dangerous N Only use the cord to disengage the motor drive mechanism Never use the cord to move the door manually
30. previously memorised during commissioning Fig 45 1 Simultaneously press the large button and the small button in the centre of the remote control The remote control indicator light flashes 2 Press the remote control button previously memorised during commissioning within 10 seconds The button for full opening has been memorised Memorise a button that has not yet been programmed to trigger partial opening Fig 24 1 Press the PROG button on the Dexxo Pro until the light comes on 2 seconds 2 Simultaneously press the outer right and outer left buttons on the remote control The remote control indicator light flashes 3 Briefly press the selected button to partially open the Dexxo Pro motor The light of the Dexxo Pro motor flashes for 5 seconds The button for full opening has been memorised Memorise a button that has not yet been programmed to trigger full opening Fig 46 1 Press the PROG button on the Dexxo Pro until the light comes on 2 seconds 2 Simultaneously press the outer right and outer left buttons on the remote control The remote control indicator light flashes 3 Briefly press the selected button to operate the Dexxo Pro motor for full opening The light of the Dexxo Pro motor flashes for 5 seconds 4 Simultaneously press the large button and the small button in the centre of the remote control The remote control indicator light flashes 5 Press the remote control button th
31. red parameter P2 taking into account the photoelectric cells or the sensor bar Orange light Fig 34 Program the setting P1 depending on the required operating mode Without warning before door movement P1 0 With a 2 s warning before door movement P1 1 Code keypad Fig 35 Pedestrian door safety kit Fig 36 When the pedestrian door contact is fitted it must be connected in place of the jumper normally fitted between terminals 5 and 6 N If the pedestrian door contact is removed the jumper between terminals 5 and 6 Battery Fig 37 Aerial Fig 38 Remote lighting Fig 39 Class 2 double insulation light units that are connected do not require an earth connection Various types of lighting can be connected without exceeding a total power consumption of 500 W SETUP General setup diagram Fig 40 Meanings of the various parameters Code Description Values Comments PO Operating mode 0 sequential Automatic closure mode operation is only possible if photoelectric 1 automatic closure cells are fitted i e P2 1 or P2 2 In automatic closure mode the door is automatically closed after the end of the time delay set with setting t0 P1 Orange warning light 0 without advance warning If the garage opens onto a public road always select with advance 1 with 2 s advance warning warning P1 1 P2 Safety input 0 no sa
32. rgentina 55 11 0 4737 37000 Australia Somfy PTY LTD 61 0 2 9638 0744 Austria Somfy GesmbH 43 0 662 62 53 08 0 Belgium Somfy Belux 32 0 2 712 07 70 Brasil Somfy Brasil STDA 55 11 0 6161 6613 Canada Somfy ULC 1 0 905 564 6446 China Somfy China Co Ltd 8621 0 6280 9660 Cyprus Somfy Middle East 357 0 25 34 55 40 Czech Republic Somfy Spol s r o 420 296 372 486 7 Denmark Somfy Nordic AB Denmark 45 65 32 57 93 Finland Somfy Nordic AB Finland 358 0 957 13 02 30 France Somfy France 33 0 820 374 374 Germany Somfy GmbH 49 0 7472 9300 Greece Somfy Hellas 30 210 614 67 68 Hong Kong Somfy Co Ltd 852 0 2523 6339 Hungary Somfy Kft 36 1814 5120 India Somfy India PVT Ltd 91 0 11 51 65 91 76 Indonesia Somfy IndonesiaEra 62 0 21 719 3620 Iran Somfy Iran 0098 217 7951036 LA RAL G TEZEICHEN TORANTRIEBE Israel Sisa Home Automation Ltd 972 0 3 952 55 54 Italy Somfy Italia s r l 39 024 84 71 84 Japan Somfy KK 81 0 45 475 0732 81 0 45 475 0922 Jordan Somfy Jordan 962 6 5821615 Kingdom of Saudi Arabia Somfy Saoudi Riyadh 966 1 47 23 203 Jeddah 966 2 69 83 353 Kuwait Somfy Kuwait 00965 4348906 Lebanon Somfy Middle East 961 0 1 391 224 Malaisia Somfy Malaisia 60 0 3 228 74743 Mexico Somfy Mexico SA de CV 52 0 55 5576 3421 Morocco Somfy Maroc 212 2295
33. s on the previously programmed remote control A until the green indicator light comes on 2 seconds 2 Press the button for 2 seconds to copy the previously programmed remote control A 3 Simultaneously briefly press the outer right and outer left buttons on the new remote control B 4 Briefly press the selected button to actuate the Dexxo Pro on the new remote control B At this stage in the installation process the Dexxo Pro motor drive unit is ready to run OPERATING TEST Using Keytis remote controls Fig 26 Using Keygo remote controls Fig 27 Obstacle detection function Fig 28 and 29 The detection of an obstacle during door opening will stop the door Fig 28 The detection of an obstacle during door closure will reopen the door Fig 29 Make sure that obstacle detection works when the door encounters an obstacle 50 mm from the ground Built in lighting operation The light will come on every time the motor drive unit is operated It will go out automatically after one minute once the door stops This time delay is adjustable refer to the Setup chapter Repetitive use which causes the light to stay on continually may result in an automatic cut off condition triggered by the thermal cut out protection mechanism CONNECTING PERIPHERALS Description of the various peripherals Fig 30 Key Description Key Description 1 Orange light 6 Battery 2 Remote lighting 7 Pedestrian door safety kit
34. s or stops the door opening motion when the door is loaded down with a 20 kg weight attached to a central position of the door s bottom edge In accordance with standard EN12453 concerning the safe use of motorised doors and gates the remote control of an automatic garage door which is not visible to the user particularly using the TAHOMA unit always requires a photoelectric cell type safety device to be installed on this automatic function Failure to comply with these instructions absolves SOMFY of any liability resulting from damage that may be caused PRODUCT DESCRIPTION Product components Fig 1 Key Number Description Key Number Description 1 1 Motor head 16 2 Shaft 2 1 Motor cover 17 2 Circlips 3 1 Built in light cover 19 4 Self shaping Y 4x8 screw 4 1 Lintel bracket 20 2 Special screw for plastic 3 5x12 5 1 Door bracket 21a 1 Single part rail 6 2 Ceiling bracket 21b 1 Two part rail 7 2 Motor head bracket 21b1 1 Sleeve 8 1 Manual release cord 21b2 8 Self shaping 4x8 screw 9 1 Link arm 22 2 HMS8 self locking nut 10 1 Travel stop 23 2 Bracket 11 4 Chain retainer pad 24 1 Spacer 12 1 Power cable 25a 1 Keytis 4 io remote control 13 4 Hex head M8x16 bolt 25b 2 Keygo io remote control 14 4 Hex head M8x12 bolt amp washer 26 1 230 V 40 W E14 socket light bulb 15 6 HU8 nut 27 1 Antenna Area of application Fig 2 Types of doors Fig 2 A Projecting
35. select the Ud setting then press OK as shown in Fig 40 Data Deseription U0 Total cycle counter tens and units U1 Total cycle counter thousands and hundreds U2 Total cycle counter hundreds of thousands U3 Cycle counter with obstacle detection tens and units U4 Cycle counter with obstacle detection thousands U5 Number of control channels memorised single direction remote control only d0tod9 Log of the last ten faults dd Clears the fault log press OK for 7 s Fig 40 12 TECHNICAL SPECIFICATIONS Dexxo Pro 800 io Dexxo Pro 1000 io BASIC TECHNICAL CHARACTERISTICS Mains supply 230 V 50 Hz Max power consumption Standby Operation 5 W 600 W with 500 W remote lighting Traction force Peak force 800 N 1000 N Starting force 1 650 N 800 N Use 20 cycles max per day with a standard rail 50 cycles max per day with a high performance rail Number of Opening Closing cycles per day tested for 36 500 cycles with a standard rail and 90 000 cycles with a high performance rail Max speed 18 cm s Programming interface 7 buttons 2 character LCD display Operating temperature 20 C 60 C indoor dry IP 20 Travel end limits Mechanical stopper at opening Memorized end limit position at closing Electrical insulation Class 2 double insulation Built in lighting 230 V 40 W E14 socket Somfy radio frequency 868 870 MHz Number
36. somfy com E Installation manual MD Installatiegids GB Instrukcja montazu Ey son Situo io Telis 1 io Impresario Telis Keytis io Keygo io Situo io A M Chronis io Composio io Keytis Home io Situo io mobile HOME MOTION BY 5048554E CONTENTS GENERAL PRESENTATION SAFETY INSTRUCTIONS Caution Safety instructions PRODUCT DESCRIPTION Product components Area of application POINTS TO CHECK PRIOR TO INSTALLATION Preliminary checks Safety instructions INSTALLATION Installation height Detailed description of installation steps PROGRAMMING Programming button description End limit setting and self learning Keytis remote control description Keygo remote control description Fitting the battery for Keytis remote controls Programming Keytis remote controls Programming Keygo remote controls OPERATING TEST Using Keytis remote controls Using Keygo remote controls Obstacle detection function Built in lighting operation CONNECTING PERIPHERALS Description of the various peripherals Electrical connections for the various peripherals SETUP General setup diagram Meanings of the various parameters PROGRAMMING KEYGO IO REMOTE CONTROLS FOR FULL AND PARTIAL OPENING OPERATION CLEARING REMOTE CONTROLS AND ALL SETTINGS Clearing remote controls Resetting all settings LOCKING PROGRAMMING REFITTING COVERS TROUBLESHOOTING Operating codes displayed Programming codes displayed Error and failure co
37. the Dexxo Pro system Reinforce them where necessary Never splash water onto the system Never install Dexxo Pro in a location where water may cause damage The bottom edge of the door should be fitted with a rubber strip to avoid hard contact and enhance the contact surface If the garage door is the only entry point into the garage fit an external release external release keylock ref 9012961 or an external release ref 9012962 and include a back up battery ref 9001001 If the garage door includes a separate pedestrian door the door must be fitted with an interlock to prevent garage door movement when the pedestrian door is open pedestrian door safety kit ref 2400657 If the garage door opens on to a public road install an indicator light such as a flashing orange light ref 9015171 If the garage door operates in automatic mode install a photoelectric cell type safety system ref 9014994 or ref 9013647 and a flashing orange light type indicator Make sure that the door does not comprise any accessible parts N Unlocking the door may trigger uncontrolled door movement if the door is not balanced correctly Safety instructions Safety instructions must be complied with throughout the installation process Take off any personal jewellery bracelet chain or others during installation work During drilling and welding work always wear safety glasses and suitable protection Always use suitable tools Take
38. the door reverses direction when an obstacle prevents the door from closing at least 50 mm above floor level The safety mechanisms cells pedestrian door contact sensor bar Check correct operation every six months refer to page 5 The back up battery To ensure optimum battery life we recommend that the power to the motor is switched off and the door is operated for a number of cycles using battery power three times a year Replacing a Keytis remote control battery Do not dispose of your scrapped appliances nor your used batteries with household waste You are liable to dispose of all your electronic or electrical equipment waste by relocating over to a dedicated collection point for recycling Mains power supply 230 V 50 Hz Power consumption on standby Sw Max power consumption 600 W with 500 W remote controlled lighting Traction force 800 N 1000 N Use 20 cycles per day with a standard rail tested for 36 500 cycles 50 cycles per day with a high performance rail tested for 90 000 cycles Number of channels that can be memorised Situo io 6 Others unlimited Somfy radio frequency 868 870 MHz Integrated light 230 V 40 W max E14 socket Remote controlled lighting 230 V 500 W max Class 2 CT Operating temperature 20 C 60 C somfy com Lists of subsidiaries Lijst van filialen Lista oddziatow Argentina Somfy A
39. ts Cd Working from back up battery Waiting for a command Programming codes displayed Des criptior ommen st Awaiting setting 1 Pressing the SET button for 2 s starts the learning mode 2 Learning mode Pressing the OK button starts the learning cycle the S2 display blinks during the entire cycle Pressing the or buttons will control the motor in forced mode FO Awaiting motor control memorisation Pressing a remote control button will assign this button to motor control Pressing the PROG button will call up the Awaiting remote lighting control memorisation mode F1 Error and failure codes displayed El Maximum force reached During learning the door requires too Check door balance and correct operation by manual much force for the motor Operation E4 Safety mechanism self test fault The safety device self test failed Check that P2 is setup correctly depending on the devices connected to the safety input Check safety device wiring When photoelectric cells are used check their proper alignment Eb Other faults and failure conditions These codes correspond to various Cut the power supply mains amp battery back up wait for a few electronic circuit board failures minutes then re connect the power supply Perform a learning cycle If the fault persists contact Somfy Technical Support Accessing stored data To access stored data
Download Pdf Manuals
Related Search