Quick-installed High Definition Speed Dome User`s Manual
Contents
1. EXIT Move the cursor to INITIAL INFORMATION and then click confirm button you can see the above interface Here you can view dome basic information 2 4 1 2 Address Information 13 ADDR TYPE ADDR HARD ADDR SOFT BACK EXIT Move the cursor to SITE INFORMATION and then click confirm button ADDR TYPE There are two options soft and hard Please use the left right button on the keyboard or in the speed dome terminal menu to set Please click the OK button to confirm ADDR HARD It is an address you set the dial switch You can not modify it through software ADDR SOFT You can set address via software It is to say you can use menu to modify dome address The value ranges from 1 to 255 BACK Go back to the previous menu EXIT Log out system menu 2 4 1 3 System Time Setting Move the cursor to SYSTEM TIME SETING and then click confirm button you can go to the third submenu Please use the left right button on the keyboard or in the speed dome terminal menu to set After completed setup please click confirm button to save current setup After you see speed dome menu displays OK you can see the setup is valid now 2 4 2 Display Setting PRESET TITLE AZIMUTH DISP TIME DISP POSITION ZOOM DISP INSIDE TEMP TITLE DISP BACK EXIT Move the cursor to DISPLAY SETUP and then click confirm button you can go to the third submenu Please use the left right button on the keyboard or in th2. 28 3 171 System CONNECHON 28 31 2 GonnGctlon eric rro nre ei A ave E pe e de ii ree 29 4 30 4 1 Dally Maintenance 30 4 2 Problems and Solutions eee eee eerte esee esee tata tatnen tatnen eset toto tots en enen inen tn ene 30 5 APPENDIX I THUNDER PROOF AND SURGE 31 6 APPENDIX 2 TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS 32 Welcome Thank you for purchasing our product This user s manual is designed to be a reference tool for the operation of your system Here you can find information about this speed dome features and functions as well as a detailed menu tree Please keep it well for future reference Before installation and operation please read the following safeguards and warnings carefully Important Safeguards and Warnings e Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 24V AC in the IEC60950 1 We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any pr
3. ACTIVATE RESIZE DELETE SAVE BACK EXIT Note For security reasons please set privacy zone a little bit larger than the privacy object size Each time after modifications you need to move the cursor to SAVE button and then click confirm button to get all setup activated Otherwise privacy zone may not move correspondingly with the object Please enter privacy mask menu now all the privacy zones are closed Move the cursor to PRIVACY NO please use left right key to set different privacy zones For example shift to 001 section and then move the cursor to ACTIVATE Secondly use left right key to select ON mode Now there is a privacy zone in the screen centre Thirdly use PTZ to move camera so that privacy object fit well with screen centre Fourthly move the cursor to RESIZE and then click left and right key to adjust privacy zone direction and size Fifthly move the cursor to SAVE and then click confirm button to exit PRIVACY NO Here is to set privacy mask zones Please use the left right button on the keyboard or in the speed dome terminal menu to set The value ranges from 1 to 24 Please note the value here may vary due to different protocols ACTIVATE There are two settings on and off When activate function is on the privacy mask function will be activated and displays in the screen When activate function is off the privacy mask function will be closed and the blank will not displayed in the s
4. Housing Bearing Connection E E E Cable Motor C If possible Power If possible Bracket 5 5 If possible Accessories Note O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes 32 Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice e If there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website or contact your local service
5. CRUISE NO 001 PATTERN NO 001 SAVE BACK EXIT When there is no available command for specified time dome automatically goes on the previous set functions IDLE FUNCTION There are two modes ON OFF Please use left right key to set IDLE TIME System idle period Please use the left right button on the keyboard or in the speed dome terminal menu to set IDLE ACTION There are several functions you can select NONE PRESET SCAN TOURING PATTERN Please use the left right button on the keyboard or in the speed dome terminal menu to set PRESET NO Here is for you to set preset number System goes to specified preset when idle status is on AUTO SCAN NO Please use the left right button on the keyboard or in the speed dome terminal menu to set System begins specified scan when idle status is on CRUISE NO Please use the left right button on the keyboard or in the speed dome terminal menu to set System begins specified touring when idle status is on PATTERN NO Please use the left right button on the keyboard or in the speed dome terminal menu to set System begins specified pattern when idle status is on SAVE Move the cursor to SAVE and click confirm button to save current setup BACK Go back to previous menu EXIT Log out system menu 2 4 4 7 Auto Run Schedule task TASK NO TIME TASK TASK SETTING TASK INFORMATION DELETE TASK BACK EXIT TASK NO Here you can set task number Please use the left right butto
6. Connection Multiple function combination cable consists of network cable audio video terminal and relay in out terminal Please refer to the following instruction labels for further reference RS485 audio video interfaces are shown below Name Function A 485 A It is to control dome built in PTZ 485 B 485 B It is to control dome built in PTZ GND Ground VIDE GND Ground O OUT Video output AC24V 24V power port Connect to the power cable EARTH Ground port AC24V 24V power port Connect to power cable 1 Please refer to the label instruction for the alarm connection information of the multiple function combination cable 2 Relay in out interfaces are shown below GND Alarm in 1 7 e Note Name Function Alarm out 1 2 1 a Two alarm output channels When there is an alarm from current channel system activates relay or not b Alarm output relay default setup is NO You can use the jump cap near the power board relay to set C NO Normal open alarm output d NC Normal close alarm output Alarm input ground end Seven alarm input channels It is to receive relay signal from the external alarm source You can go to dome menu to activate specified preset or patter When the activation mode is NO normal open dome alarms when there is low voltage High voltage will not activate the alarm When the activation mode is NC normal close dome
7. address The dome will begin an auto touring between these addresses You can set 8 touring paths Each touring path can contain max 32 presets 1 2 8 Auto Pattern Memorize dome operation such as pan tilt and zoom to repeat Focus and iris are in auto mode during auto pattern For each pattern the time should be less than 60 seconds 1 2 9 Privacy Masking Privacy masking is a user defined four sided area that can not be viewed by you The masking area will move with pan and tilt functions and automatically adjust in size as the lens zooms 1 2 10 Action on Alarm This series quick installed high definition speed dome has 2 alarm inputs normal open or normal close and 1 alarm outputs normal open Alarms can be individually programmed to initiated pattern or go to an associated preset scanning touring when received Dome will return to a previously programmed state after alarm acknowledgement or to its previous position before alarm 1 2 11 Auto Flip As long as you continue to hold the keyboard joystick in the down position the dome rotates 180 degrees and repositions itself for uninterrupted viewing of any subjects that passes directly beneath the dome 1 2 12 Self diagnosis There is a self diagnosis procedure when dome boots up Tilt and vertical engine check Camera diagnostics Display dome information and diagnosis information such as address protocol baud rate type 1 2 13 Day Night Mode B W amp Color Mode Auto manual
8. diagnosis There is a noise Power supply is inadequate Replace power socket Mechanical malfunction Need electrical engineer help Video signal loss occurs in high speed rotation Power supply is not sufficient Replace power socket Video signal is not successive Circuit connection is too loose Connect tightly Video switch or power problem Need electrical engineer help Video is not clear Dome cover is dirty Focus is in manual mode Control manually Wash dome cover During camera Switch there is a tilt movement in the monitor Camera power is not in the same Phase When several domes are connected to one transformer please connect the transformer output cable to the domes same side 30 5 Appendix Thunder Proof and Surge Protection This series speed dome adopts TVS lighting protection technology It can effectively prevent damages from various pulse signals below 1500W such as sudden lighting and surge While maintaining your local electrical safety code you still need to take necessary precaution measures when installing the speed dome in the outdoor environment The distance between the signal transmission cable and high voltage device or high voltage cable shall be at least 50 meters Outdoor cable layout shall go under the penthouse if possible For vast land please use sealing steel tube under the land to implement cable layo
9. is Time Move the cursor to DAY TIME item and then click confirm button to go to setup Please user up down button to set the value After completed setup please click confirm button to exit and move the cursor to Save button to save current setup NIGHT TIME Current setup becomes valid when day night mode is Time Move the cursor to DAY TIME item and then click confirm button to go to setup Please user up down button to set the value After completed setup please click confirm button to exit and move the cursor to save button to save current setup THRESHOLD The speed dome can switch the day night mode when it reached the threshold you set here SAVE This button is for DAY TIME and NIGHT TIME setup After you set the day time or night time you need to move the cursor here and then click confirm button to save current time setup For other Setups you do not need to use this button BACK Go back to previous menu EXIT Log out system menu 2 4 3 4 Next Page Move the cursor to NEXT PAGE and then click confirm button you can go to the submenu APERTURE RESTRAIN DIGITAL ZOOM PICTURE FLIP FREEZE FUNC AF SENSITIVITY CAMERA FACTORY DEFAULT CAMERA RESTATRT BACK EXIT APERTURE RESTRAIN It can automatically control the aperture in the low illumination environments It can reduce the noise DIGITAL ZOOM You can use the left right button to enable disable the digital zoom function PICTURE FLIP This function allo
10. setup here will not lose when encounter power failure 2 4 1 System Information INITIAL INFORMATION ADDR INFORMATION SYSTEM TIME SETTING SET NORTH LANGUAGE ENGLISH FACTORY DEFAULT RESTART BACK EXIT INITIAL INFORMATION Move the cursor to INITIAL INFORMATION and then click confirm button to go to the third submenu ADDR INFORMATION Move the cursor to SITE INFORMATION and then click confirm button to go to the third submenu SYSTEM TIME SETTING Move the cursor to SYSTEM TIME SETTING and then click confirm button to go to the third submenu SET NORTH DIRECTION Set dome benchmark direction so that you can know the angel between the benchmark and then current location Please move the cursor to the option and then click confirm button until you see O K Now you have set north direction LANGUAGE The dome menu language There are several languages for you to select Please use the left right button on the keyboard or in the speed dome terminal menu to set FACTORY DEFAULT Restore dome factory default setup Please move the cursor to the option and then click confirm button until you see O K Now you can see the IP dome begin rebooting to restore factory default setup RESTART Reboot the speed dome BACK Go back to the previous menu EXIT Log out system menu 2 4 1 1 Initialization information ADDR 001 BAUD RATE 9600 PARITY NONE PROTOCOL PELCO D MODEL SD6663 HN 032 C TEMP SOFTWARE
11. IDLE PTZ AUTO STOP HEATER SAVE BACK EXIT e PRIVACY MASK Here you can set the privacy mask number and etc It includes the third menu Please move the cursor to the current item and then click the confirm button to go to the next interface e PTZ SPEED It is to set PTZ speed Please use the left right button to set e SET ZERO It is to set the PTZ initial position Please move the PTZ to the corresponding position and then click the confirm button to complete the setup e POWER It is to set the PTZ action when the speed dome boots up Click the confirm button to go to the next interface To set e MENU PASSWORD It is to set the password to go to the PTZ menu Click the confirm button to go to the next interface To set e MENU IDLE If current setup is ON once you open the menu and leave it idle for specified period the menu may automatically disappear If current setup is OFF the menu is always there and will not disappear Please use the left right button to set e PTZ AUTO STOP The speed dome will stop all the PTZ operations when there is no command for the specified time It includes various setups Please use the left right button to set e HEATER SETTING There are three options NO NC Auto The default setup is auto e BACK Go back to the previous menu e EXIT Log out the system menu ian Mask Move the cursor to PRIVACY MASK and click confirm button system goes to privacy mask setup interface 24 PRIVACY
12. Quick installed High Definition Speed Dome User s Manual Version 1 0 Table of Contents 1 FEATURES AND FUNCTIONS on 7 1 1 General 7 1 2 7 1 2 1 On Screen 7 1 2 3 Support multiple protocols 7 1 2 3 s Proportional Pan arnd Tilt t e qr ERI ED IGI e es 7 1 24 On screen PpS scene R A 7 1 2 5 PresetSetup and Call Rech Romi EO 7 1 2 6 Auto SCAM oed teen eR eG eR EAR Ue eei qiie p 7 CAT Auto TOUT c e ARRIERE Oe ONT LATINO ORI 7 1 2 8 Pattern sos ehh cde a eee cepe n ae ee Eis 7 1 2 9 Privacy MASKING s c eer On ptam e Een ERU 7 1 2 10 Action on Alartm epus eque eter d 8 1 2 11 Auto Flip neh ae hee Ail RS du e ett attulisset bates 8 1 2 12 SEM GIAGNOSIS E 8 1 2 13 Day Night Mode B W amp Color Mode eene etre nennen 8 1 2 14 Auto FOCUS iicet RENE ER ARR IR RR RR ER REN IER cte lecti 8 1 2 15 Backlight Compensatii a RR RH RR RR RR 8 1 2 16 Pan Tilt arid Zoom sce A diete he C Re 8 1 2 17 3D Intelligent intet dte Es 8 1 2 18 Idle Statli
13. RE SETTING DAY NIGHT SETTING FOCUS MODE AUTO FOCUS LIMIT 30CM ZOOM SPEED 08 APERTURE 09 NEXT PAGE BACK EXIT Move the cursor to CAMERA SETTING and then click confirm button you can go to the submenu WHITE BALANCE SETUP Move the cursor to current option and then click confirm button you can go to the third menu EXPOSURE SETTING Move the cursor to current option and then click confirm button you can go to the third menu DAY NIGHT Set day night mode Move the cursor to current option and then click confirm button you can go to the third menu There are three options auto manual off Please use the left right button on the keyboard or in the speed dome terminal menu to set Please makes sure your product supports this function FOCUS MODE There are two modes Manual Auto Please use the left right button on the keyboard or in the speed dome terminal menu to set FOCUS LIMIT It is to set the distance between the camera and the object It can prevent the focus distance is too small which may result in focusing on the enclosure At the same time you can change the distance to change the focus speed ZOOM SPEED The bigger the value the faster the speed Please use the left right button on the keyboard or in the speed dome terminal menu to set APERTURE It is to adjust the lens to achieve clear video Please use the left right button on the keyboard or in the speed dome terminal menu to set NE
14. UTO GAIN LIMIT AUTO SLOW SHUTTER LOW LIMIT NOISE CONTROL BLC WDR BACK and EXIT Move the cursor to the item and then click the left right button to set o AUTO GAIN LIMIT Please click the left right button to set 16 SLOW SHUTTER LOW LIMIT Please click the left right button to set NOISE REDUCTION There may noise when the camera is monitoring the low illumination environments You can use the digital filter to process the noise to guarantee the clear video o Itis an abbreviation for back light compensation System can compensate the object in the dark light to achieve a clear video Please use the left right button on the keyboard or in the speed dome terminal menu to set WDRENBALE It is an abbreviation for wide dynamic region Please make sure your camera supports current function This function can adjust the video brightness when the contrast between the strong light and the dark light is too high Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 2 4 3 3 Day Night Setting Move the cursor to DAY NIGHT SETTING and then click confirm button you can go to the submenu DAY NIGHT AUTO DAY TIME 07H 00M NIGHT TIME 19H 00M THRESHOD 4 SAVE BACK EXIT DAY NIGHT Please use the left right button on the keyboard or in the speed dome terminal menu to set DAY TIME Current setup becomes valid when day night mode
15. XT PAGE It includes the following options APERTURE RESTRAIN DIGITAL ZOOM PICTURE FLIP FREEZE FUNCTION AF SENSITIVITY CAMERA FACTORY DEFAULT SETUP CAMERA RESTART Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 2 4 3 1 White Balance Setup WB MODE AUTO R GAIN B GAIN BACK EXIT Move the cursor to WHITE BALANCE MODE and then click confirm button you can go to the submenu WHITE BALANCE MODE Set white balance adjustment mode There are two modes auto manual Please use the left right button on the keyboard or in the speed dome terminal menu to set R GAIN Before you set GAIN option please note the mode shall not be auto Please use the left right button on the keyboard or in the speed dome terminal menu to set B GAIN Before you set B GAIN option please note the mode shall not be auto Please use the left right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 2 4 3 2 Exposure Setting AE MODE AGC GAIN LIMIT GAIN SETTING SLOW SHUTTER LIMIT SHUTTER NOISE REDUCTION IRIS SETTING BLC EXPOSURE COMP WDR ENABLE SLOW AE 01 BACK SLOW SHUTTER EXIT NEXT PAGE BACK EXIT MODE Here you can set the camera exposure mode It includes auto manual AV iris priority TV shutter priority Pleas
16. Y BACK CAMERA SETTING WB SETTING EXPOSURE SETTING DAY NIGHT SETTING S MOD AUTO AUTO MANUAL 08 01 08 06 01 16 FUNCTION SETTING AUTO SCAN CRUISE PATTERN IDLE MOTION AUTO RUN E PAGE ALARM SETTING ALARM NO ACTION CONTACT PRESET AUTO SCAN CRUISE 001 RELAY OUT OFF OFF 1 5S 2 5S 1 amp 2 5S RESET DELAY 35 EXIT SAVE 11 The above diagram illustrates the overall structure of the speed dome setup menu Note ERR means current setup is invalid Please make sure all the cable connections are right 2 2 Self diagnosis System Information ADDR 001 H BAUD RATE 9600 PARITY NONE PROTOCOL PELCO P MODEL SD66XX SOFTWARE V1 04 3 BACK EXIT After installation please connect speed dome to power The system goes on a self diagnosis and then it pops up the above interface to show the system information If there is anything wrong during the self diagnosis system pops up error code The above interface disappears after speed dome received the first command or the display time lasts for 4 minutes ADDR Here you can view dome address information For example 001 1 is the address number H is hard address mode is software address mode Baud rate Dome communication baud rate Parity Communication parity bit format Protocol Current communication protocol Model Dome type Software Dome PTZ software version 2 3 Main Menu You can
17. alarms when there is high voltage Low voltage will not activate the alarm Dome alarm input message is ground mode Dome alarm input signal are two modes normal open and normal close 3 1 System Layout 3 1 1 System Connection 28 Please refer to Figure 3 1 for system connection information Network Output B Figure 3 1 AC24V AC24V Input Transfor mer 3 1 2 Alarm Connection Please refer to Figure 3 2 for alarm connection information Alarm Controller Figure 3 2 29 4 FAQ 4 1 Daily Maintenance Please clean dome cover regularly to get vivid image Handle the cover with care Use water to wash Don t use cloth to clean Use mild detergent to clean if there is too much dust Note The sweat from your hand may erode plating surface your nail may scrape dome cover result in blur image 4 2 Problems and Solutions SYMPTOM CAUSE SOLUTION No self diagnosis no video signal when connect dome to power Red LED is not on 24V AC does not apply to the power Or connection is Check 24V AC power is connected or properly earthed too loose Check power supply condition Power off or Transformer or check 24V transformer problem Red LED light is on 24V AC power is low Something wrong with power socket Use multimeter to check dome load Please contact retailer to replace power socket No self
18. chnical Specifications Power AC 24 10 Includes temperature control circuit Camera Driver Consumption 12W Decoder Built in Engine Stepper motor Preset 255 In PELCOD PELCOP protocol 80 In industrial protocol Please note the value may vary due to different protocols Auto Tour 8 Auto Pattern 5 Auto Scan 5 Privacy Mask 8 zones in one window The different series products support different amount depends on the camera type Alarm Input Output 7 2 Environment 40 C 60 C outdoor Information Time address dome title dome coordinates temperature alarm and etc Lens Adjust speed in accordance with lens Auto Rotation Tilt 92 auto rotates to pan 180 Auto Pan 0 360 continuously Manual Pan Motion 0 1 200 S Speed Preset Maximum 300 Speed Manual Tilt Motion 0 19 1209 5 Manual Tilt Scan 0 180 Section PTZ Scan Accuracy 0 06 0 015 Signal Format PAL NTSC Camera mode S N Ratio gt 50dB Humidity lt 90 10 2 Menu 2 1 Screen Menu Index Note ERR means current setup is invalid means there is submenu INITIAL INFORMATION SYSTEM ADDR INFORMATION INFORMATION SYSTEM TIME SETTING SET NORTH LA ENGLISH NGUAGE FACTORY DEFAULT START DISPLAY SETTING PRESET TITLE AZIMUTH DISP TIME DISP POSITION ZOOM DISP INSIDE TEMP TITILE DISPLA
19. click confirm button to exit start time setup and then move the cursor to the SAVE button to save current setup END TIME Here you can set the task end time Move the cursor to current item and then click confirm button to set the time Please use the up down button to set the detail value and then use left right button to go to the next setup item After you completed the setup please click confirm button to exit end time setup and then move the cursor to the SAVE button to save current setup TASK ACTION The option here includes none tour scan preset patter and etc Please use left right button to set OPERATION NO It is the corresponding serial number of the schedule task The number here may vary due to different action types BACK Go back to the previous menu EXIT Log out the system menu Task Information Move the cursor to the TASK INFORMATION and then click the confirm button to go to the following interface Here you can see the corresponding task information Click the confirm button again you can exit current interface 23 TIME ACTION 00 00 00 5 001 00 00 00 5 001 00 00 00 5 001 00 00 00 5 001 00 00 00 5 001 00 00 00 5 001 00 00 00 5 001 2 4 4 8 Page Move the cursor to the NEXT PAGE and then click the confirm button you can go to the third menu to set the PTZ SPEED SET ZERO POWER UP and etc PRIVACY MASK PTZ SPEED SET ZERO POWER UP MENU PASSWORD MENU
20. confirm button You can see the following interface Here you can add or remove the preset and set the corresponding dwell time and call speed NO PRESET DWELL SPEED 01 000 005 013 02 000 005 013 03 000 005 013 32 000 005 013 20 B DWELL Here is t set dwell time Please use the left right button the keyboard or in the speed dome terminal menu to set B SPEED Here you can set the speed value When you move the cursor to one cruise number you can use left right button to turn the page When you move the cursor to one cruise number please click confirm button to set the cruise Please use up down button to set preset number dwell time and speed Use the left right button to go to the next cruise Click confirm button you can exit the setup After you completed the setup move the cursor to back button to go to the previous interface DELETE CRUISE Here is to delete a cruise Input cruise number in CRUISE NO and then move the cursor to DELETE cruise click confirm button to delete CALL Here is to activate cruise Input touring number in touring NO and highlight CALL click confirm button to activate touring STOP Here is to terminate touring BACK Go back to previous menu EXIT Log out system menu 2 4 4 5 Pattern PATTERN NO 001 PROGRAM START PROGRAM STOP RUN STOP BACK EXIT Pattern function can memory PTZ operation and camera focus zoom in and zoom out From the start position dome begins au
21. creen RESIZE It is to adjust the privacy zone size Please continue pressing direction button to widen or narrow zone size lt is to narrow the horizontal width is to widen the horizontal width 7 is to widen vertical height and is to narrow the vertical height SAVE Here is to save user setup DELETE Here is to delete setup and restore default setting BACK Go back to previous menu EXIT Log out system menu Power Up Move the cursor to the POWER UP item and then click the confirm button you can go to the fourth menu POWER UP PARAMTER BACK EXIT e POWER UP It is to set the PTZ operation when the speed dome boots up The option includes NONE AUTO SCAN PRESET PATTERN TOUR and etc Please use the left right button to set e PARAMTER Here you can set the serial number of the corresponding operation such as the scan preset pattern tour Please use the left right button to set 25 e BACK Go back to the previous menu e EXIT Log out the system menu Menu Password Move the cursor to the MENU PASSWORD and the click the confirm button to go to the fourth menu PASSWORD PASSWORD 1 2345 SETTING 6 7890 BACK SAVE BACK EXIT e PASSWORD It is to set the speed dome menu password Please use the left right button to set e SETTING Click the confirm button to go to the password setup interface Please use the left right button to set the value and then click the confirm button t
22. cursor to PATTERN and then click confirm button to go to the third submenu IDLE MOTION Move the cursor to IDLE MOTION and then click confirm button to go to the third submenu TIME TASK Move the cursor to TIME TASK and then click confirm button to go to the third submenu NEXT PAGE It includes PRIVACY MASKING PTZ SPEED SET ZERO POWER UP MENU PASSWORD MENU IDEL PTZ AUTO STOP and HEATER Move the cursor to the item and then click the confirm button to set BACK Go back to previous menu EXIT Log out system menu 18 2 4 4 1 Preset Setup PRESET NO 001 TITLE PRESETOO1 SETTING CALL BACK Move the cursor to PRESET button and then click confirm button to go to set interface PRESET NO Please use left right key to modify preset number The different protocols support different preset values The PELCOD and PELCOP support 1 to 255 For the industrial protocol the value ranges from 1 to 80 TITLE Title text is the label used for you to identify the camera System will automatically name a title for the camera SETTING Please input preset number first and then select the monitor zone Please move the cursor to setting and click confirm button The system will pop up a message PRESET Here means preset number And the SETTING column pops up an OK Now you successfully added a preset Please note you need to enable display preset title function first Main menu gt display setting gt prese
23. d or in the speed dome terminal menu to set The camera will begin auto scan after alarm occurs 26 CRUISE Please use the left right button on the keyboard or in the speed dome terminal menu to set The camera will begin auto cruise when alarm occurs RELAY OUT Here is to set relay alarm mode and reset time There are several options off 1 5S 2 5S 18 amp 2 5S lt 1 55 1 means the first relay output 5S means the relay will reset automatically in five seconds after alarm occurs lt 182 55 1 amp 2 means the first relay and the second relay work at the same time RESET DELAY Here is for you to set alarm reset time Please use the left right button on the keyboard or in the speed dome terminal menu to set 3 seconds 10 seconds 30 seconds 60 seconds 120seconds The dome will go back to previous setup after alarm acknowledgement SAVE Move the cursor to SAVE and then click confirm button to save current setup BACK Go back to previous menu EXIT Log out system menu 2 5 Dome Abnormal Phenomenon Operation 2 5 1 Restore to Factory Default Setup From main menu SYSTEM INFORMATION move cursor to FACTORY DEFAULT and click confirm button Dome will reboot and all the setups restore to factory default setup 2 5 2 PTZ Movement is not smooth From menu to SYSTEM INFORMATION move cursor to RESTART and click confirm button This reboot will not modify all activated setup such as preset tour and pattern 27 3 Cable
24. e speed dome terminal menu to set After completed setup please click save button to save current setup PRESET TITLE Display dome preset title or not Please use the left right button on the keyboard or in the speed dome terminal menu to set You can go to Function Setup gt Preset section to set corresponding preset value and preset title AZIMUTH DISP Display dome current coordinates or not Please use the left right button on the keyboard or in the speed dome terminal menu to set TIME DISP Display dome system time or not Please use the left right button on the keyboard or in the speed dome terminal menu to set POSITION Display the angel between the benchmark and then current location Please use the left right button on the keyboard or in the speed dome terminal menu to set 14 ZOOM DISP Display speed dome zoom speed or not Please use the left right button on the keyboard or in the speed dome terminal menu to set INSIDE TEMPERATURE Display dome internal temperature or not There are three options C F Off Please use the left right button on the keyboard or in the speed dome terminal menu to set TITLE DISPLAY Here you can set to display speed dome position information and etc You can use the speed dome control terminal to set the detailed title information Please use the left right button to set BACK Go back to the previous menu EXIT Log out system menu 2 4 3 Camera Setting WB SETTING EXPOSU
25. e use the left right button on the keyboard or in the speed dome terminal menu to set o Auto It becomes valid after you set the exposure compensation backlight compensation BLC slow shutter wide dynamic region WDR o Manual It becomes valid after you set the gain setting shutter iris setting wide dynamic region WDR o It becomes valid after you set the exposure setting iris setting wide dynamic region WDR o TV It becomes valid after you set the shutter setting exposure compensation wide dynamic region WDR GAIN SETTING Please use the left right button on the keyboard or in the speed dome terminal menu to set SHUTTER Please use the left right button on the keyboard or in the speed dome terminal menu to set IRIS SETTING Please use the left right button on the keyboard or in the speed dome terminal menu to set EXPOSURE COM Please use the left right button on the keyboard or in the speed dome terminal menu to set SLOW AE In the strong light environment you can lower the camera exposure speed to capture the image and enhance the definition Please use the left right button on the keyboard or in the speed dome terminal menu to set SLOW SHUTTER In lower illumination environment you can lower the cameras auto exposure time to capture the image and enhance the definition Please use the left right button on the keyboard or in the speed dome terminal menu to set NEXT PAGE It includes A
26. ection board No data loss when power off occurs e Integrated design high stability e Quick installed high definition speed dome max support 255 presets Support 8 auto touring Each touring max has 32 presets e Low and medium speed dome max support 80 presets e 5 auto scan e 5 auto pattern Each pattern can max support 400 commands and the interval shall be less than 60s e Built in direction indicator e Support max 24 privacy mask zones Depends on the camera type e 7 alarm inputs 2 alarm outputs Built in PTZ e Fine stepper driver stable performance react quickly precisely positioning e Integrated design tight structure e Elegant mechanical driver device Support 360 degrees continuous rotation no monitor blind spot e 0 1 s rotation speed while maintain stable image e 180 degrees tilt continuous monitor Built in zoom Set 7 channel alarm inputs and 2 channel alarm outputs Set auto patter Set auto day night switch Auto B W amp color switch Depends on the camera type e Set privacy mask zones lens high sensitive e Auto focus high e Auto resolution e Auto brightness control integrated e Auto white balance digital e Auto day night switch Auto B W amp color switch Depends on the process camera type color camera e Preset title display e View dome initial setup information e Modify camera parameter e Set preset OSD Set auto scan e e 1 3 2 Te
27. engineer for more information 33
28. n The dome begins 360 degrees continuous rotation STOP Highlight stop item and then click confirm button The dome stops rotation BACK Go back to previous menu 19 EXIT Log out system menu 2 4 4 3 Scan SCAN NO 001 SET LEFT LIMIT SET RIGHT LIMIT SCAN SPEED 160 RUN STOP BACK EXIT Move the cursor to SCAN button and then click confirm button SCAN NO Here is to set auto scan number Please use the left right button on the keyboard or in the speed dome terminal menu to set SET LEFT LIMIT Here is to set camera left address Click confirm button to save current setup SET RIGHT LIMIT Here is to set camera right address Click confirm button to save current setup SCAN SPEED Please use the left right button on the keyboard or in the speed dome terminal menu to set RUN Please input auto scan number first and then please move the cursor to RUN and click confirm button to activate auto scan function STOP Here is to terminate auto scan function BACK Go back to previous menu EXIT Log out system menu 2 4 4 4 Cruise Touring CRUISE NO 001 CRUISE SETTING DELETE CRUISE RUN STOP BACK EXIT Move the cursor to highlight CRUISE item and then click confirm button to go to set interface CRUISE NO Here is to ser tour number Please use the left right button on the keyboard or in the speed dome terminal menu to set CRUISE SETTING Move the cursor to cruise setting item and then click
29. n to set TIME TASK The schedule task allows the speed dome to implement corresponding setup during the specified time There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set TASK SETTING Here you can set task time operation operation SN and etc Please click the confirm button to go to the fourth menu to set TASK INFORMATION Here you can view the corresponding task information Please click the confirm button to go to the fourth menu to set DELETE TASK Please input the task number to be deleted in the TASK NO and then move the cursor to the current item Click the confirm button you can remove all the setups in the current schedule task Now current task is null BACK Go back to the previous menu EXIT Log out the system menu Task Setting Move the cursor to the TASK SETTING and then click the confirm button you can set the task begin time end time action and etc WEEK START TIME END TIME RUN ACTION PRESET NO SAVE BACK EXIT WEEK Here you can set the week information Please use the left right button to set You can set for one day or you can set for the whole week START TIME Here you can set the task begin time Move the cursor to current item and then click confirm button to set the time Please use the up down button to set the detailed value and then use left right button to go to the next setup item After you completed the setup please
30. o confirm current option Move the cursor to the SAVE button and then click the confirm button to save current setup Click the BACK button to go to the previous menu e BACK Go back to the previous menu e EXIT Log out the system menu If you have forgot your password After three times of login failure system may pop up an 8 digit internal code Please contact our technical engineer for help 2 4 5 Alarm Setup ALARM NO ACTION CONTACT PRESET AUTO SCAN CRUISE 001 E d OUT OFF 1 55 2 53 182 RESET DELAY 35 SAVE Move the cursor to highlight ALARM SETTING button and then click confirm button ALARM NO Here is to set alarm input Alarm input value ranges from 1 to 7 Please use the left right button on the keyboard or in the speed dome terminal menu to set ACTION Action on alarm function It includes NONE PRESET AUTO SCAN TOURING functions Please use the left right button on the keyboard or in the speed dome terminal menu to set CONTACT You can set system activation operation once alarm occurred There are two alarm signal mode normal open N O and normal closed N C Please use the left right button on the keyboard or in the speed dome terminal menu to set PRESET NO Please use the left right button on the keyboard or in the speed dome terminal menu to set The camera will turn to the specified preset to monitor after alarm occurs AUTO SCAN Please use the left right button on the keyboar
31. oblems caused by unauthorized modification or attempted repair Transportation Security No heawy stress violent vibration or water splash are allowed during transportation storage and installation Please use the original packing material or the material of the same quality when you ship it back to the manufacturer Installation Do not apply power to the product before completing installation Do not put object on the product Environment This series product should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc Please keep it away from the electromagnetic radiation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the device Please make sure the CCD CMOS component is out of the radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage Daily Maintenance Current series product has no power button Please unplug all corresponding power cables before your begin installation or daily maintenance work Please keep the dustproof cap back to protect the CCD or CMOS part if the device does not work for a long time Do not touch CCD CMOS component You can use the blower to clean the dust on the surface of the device You can use the dry cloth with some alcohol or mild detergent to clear if necessary Do not use the volatility solvent such as the benzene or thinner o
32. open the IP dome menu via control keyboard matrix or speed dome control terminal SYSTEM INFORMATION DISPLAY SETTING CAMERA SETTING FUNCTION SETTING IR LIGHT SETTING ALARM SETTING EXIT SYSTEM INFORMATION Dome self diagnosis information address information system time setup set north direction language factory default setup reboot and so on DISPLAY INFORMATION Display dome preset title azimuth display time direction dome internal temperature and etc information CAMERA PARAMETERS Display dome white balance setup camera function setup day night setup shutter setup and etc FUNCTION SETTING Set preset pan scan auto cruise pattern idle motion time task and privacy mask function ALARM SETTING Set dome alarm number action contact preset scan cruise replay out reset delay save setup and etc EXIT Log out the system menu 12 2 4 Menu Operation In the speed dome main menu you can use the left right button on the keyboard or in the speed dome terminal menu to configure the system menu Before setup please move the cursor to the current item you want to configure In main menu please click confirm button to go to the sub menu or use left right key to configure setup Use up down button to select back option and then click confirm button to go back to the previous menu Use up down button to select exit option and then click confirm button to log out system menu All
33. r detergent with strong abradibility It may result in lens damage or it may adversely affect the device performance If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device 6 About Accessories Always use all the accessories recommended by manufacturer Before installation please open the package and check that all the components are included in the package Contact you local retailer ASAP if something is missing in your package 1 Features and Functions 1 1 General Introduction The six inch megapixel high speed smart network dome camera integrates the functions of network based remote surveillance and integrated high speed smart dome which makes it convenient to install and easy to use This product enjoys a megapixel resolution which meets the customers needs for surveillance at HD level This product is also qualified with intelligent identification ability privacy masking settings alarm activation WDR and some other functions In addition one can transmit audio video and control data via internet in a safe way Thus the surveillance is free from the restriction caused by the changes of time and places to realize a real time surveillance With the built in high speed PTZ this product can realize a fast accurate fixed positioning surveillance in a convenient way 1 2 Features This series speed dome has the following feat
34. s 5 aie eiie a e t eia ed rtr eie mr ed 8 1 2 19 Mage eir loliraz siio 8 1 3 Specifications me 8 1 3 4 Performance Specifications 8 1 3 2 Technical 9 AME bee 11 2 1 Screen MENU INGOX ee 11 2 2 Self diagnosis System Information sssessesossssosescosesossssosescosesossssososeosesossssososcosesessssosescssesessssosessosesesessososese 12 2 3 E E E E EE N E E H 12 2 4 Melee 13 2 4 1 sire St rt tede Ut qm 13 EASIER 14 2 4 3 Camera Setting atenta EORR ERE Ra Rem ORO OR 15 2 44 Function Setting etre n II e Pr een E ERN ERRA 18 24 5 Alarm Setup ete a tad E n BR ER RR Oa ARRAS 26 2 5 Dome Abnormal Phenomenon Operation eerie esee eene esee en en ena neon tata enata tne te tata enses eese tata 27 2 5 1 Restore to Factory Default Setup 27 2 5 2 PTZ Movement is not smooth sss e eee ne e en neret nnns 27 3 cin cea eun eem cuan eeu e cux n ex m tuv n eu m tux 28 3 1
35. switches in low illumination Auto camera will automatically adjust CCD light level Manual use menu or function keys to select day night mode This function needs the speed dome driver camera supported 1 2 14 Auto Focus Auto focus allows the lens to remain in focus during zoom in zoom out and motion functions to get vivid image You can use FAR or NEAR button to adjust focus manually 1 2 15 Backlight Compensation Balance the brightest and darkest sections of a scene to produce a more vivid picture 1 2 16 Pan Tilt and Zoom Supports zoom in and zoom out during tilt and pan movement In this period focus and iris are both in auto mode to get vivid image 1 2 17 3D Intelligent Location Working with DVR just click part of the current scene will be displayed in the central window and automatically zooms All of these allow you to trace precisely 1 2 18 Idle Status When there is no available order you can use menu to set dome idle status after specified duration The idle status includes turn to specified preset or go to scan tour or pattern function 1 2 19 Image Stabilizer Flip You can enable image stabilizer function and flip in the menu When there is vibration this IS function can guarantee video stability and when flip you can view video more clearly This function needs speed dome driver camera supported 1 3 Specifications 1 3 1 Performance Specifications Built in Decode All digital design All data are in the conn
36. t title Repeat the above procedures to set more presets Once you want to modify a preset you can input the preset number you want to modify and then follow the above steps to set the preset You can successfully modify a preset content CALL Here is to recall preset Move the cursor to PRESET NO and then input corresponding preset value Then move the cursor to CALL and then click confirm button to go to a preset BACK Go back to previous menu EXIT Log out system menu For PELCO protocol user please refer to the following special functions Call preset Call preset 28 or preset 95 to go to dome menu Call preset 29 or preset 99 to go to scan Call preset 24 or preset 81 to go to pattern Call preset 25 or preset 82 to go to cruise tour Call preset 30 or preset 96 to stop scan or pattern Call preset 31 or preset 83 to begin rotation Call preset 33 to enable PTZ 180 degrees rotation Call preset 34 to set dome position as 0 Set preset Set preset 26 or 92 to set scan left limit Set preset 27 or 93 to set scan right limit Set preset 22 or 79 to begin record Set preset 23 or 80 to stop record 2 4 4 2 Pan PAN SPEED 160 RUN STOP BACK EXIT Move the cursor to PAN button and then click confirm button to go to setup interface PAN SPEED Set dome rotation speed Please use the left right button on the keyboard or in the speed dome terminal menu to set RUN Move the cursor to call item and then click confirm butto
37. to movement repeatedly This series IP dome supports maximum 5 patterns and one pattern can max support 400 commands Move the cursor to PATTERN and click confirm button PATTERN NO Here is to set pattern number The value ranges from 1 to 5 Please click left right key to configure PROGRAM START Here is to memorize pattern starting point An icon OK pops up in screen to prompt you system begins memory pattern PROGRAM STOP Here is to set pattern stop point After all the movement move the cursor to PROGRAM STOP and then click confirm button Now you have set one pattern System pops up an icon OK to prompt you system has memories one pattern RUN Here is to activate pattern Input pattern number move the cursor to RUN and click confirm button system begins running pattern STOP Here is to stop current pattern Input pattern number move the cursor to STOP and click confirm button System stops current pattern BACK Go back to previous menu 21 EXIT Log out system menu Note The dwell time between two orders should be less than one minute otherwise system will set to default value as one minute After click PROGRAM STOP do not click CALL button before icon disappears completely Any manual operation during the pattern procedure will terminate current dome pattern operation 2 4 4 6 Idle Motion IDLE FUNC OFF IDLE TIME 010MIN IDLE ACTION PRESET PRESET NO 001 AUTO SCAN NO 001
38. ures 1 2 1 On Screen Menu This series product menu supports multiple languages It is easy for you to view dome information and configure dome camera parameters 1 2 2 Support multiple protocols You can use various devices such as matrix control keyboard and DVR and protocols to operate speed dome 1 2 3 Proportional Pan and Tilt This function keeps the image from moving too fast when there is a large amount of zoom The quick installed high definition speed dome continually decreases or increases pan and tilt speeds in proportion to depth of zoom When zooms speed is increasing the camera moving speed becomes slow When zooms speed is decreasing the camera moving speed becomes fast 1 2 4 On screen Tips Here you can view Dome title and system version Software and hardware Dome system temperature Optional You can disable this function Dome pan tilt coordinates preset ID 1 2 5 Preset Setup and Call Preset function is to save the address information such as PTZ pan tilt focus and etc to the memory so that you can quickly adjust the dome and PTZ to the correct position This series quick installed high definition speed dome supports 255 presets 1 2 6 Auto Scan Camera scans back and forth regularly in a horizontal field Here you need to set left and right limit and scan speed You can set 5 scanning paths 1 2 7 Auto Touring Add addresses into a routine in a desired order and then set time and stop duration for each
39. ut and connects one point to the earth Open floor cable layout is forbidden In area of strong thunderstorm hit or near high sensitive voltage such as near high voltage transformer substation you need to install additional high power thunder protection device or lightning rod The thunder protection and earth of the outdoor device and cable shall be considered in the building whole thunder protection and conform to your local national or industry standard System shall adopt equal potential wiring The earth device shall meet anti jamming and at the same time conforms to your local electrical safety code The earth device shall not short circuit to N neutral line of high voltage power grid or mixed with other wires When connect the system to the earth alone the earth resistance shall not be more than 4 9 and earth cable cross sectional area shall below 25 mm2 See Figure 5 1 Video Lighting Rod Communication _ Liqhting Rod Power Xs xa Lighting Rod The speed dome shall be installed within the 45 angel of the lighting rod Earth cable resistance shall be less than 40 Steel tube shield Figure 5 1 3l 6 Appendix 2 Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Pb Hg Cd Cr VI PBB PBDE Sheet Metal Plastic Parts
40. ws you to turn the image rotation 180 degrees There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set FREEZE FUNCTION This function allows the system from one preset to another preset without showing the video during the PTZ movement There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set AF SENSITIVITY You can set the auto focus threshold value here CAMERA FACTORY DEFAULT SETTING Move the cursor to current item and then click confirm button to restore factory default setup CAMERE RESTART Move the cursor to current item and then click confirm button to reboot the camera BACK Go back to previous menu EXIT Log out system menu 2 4 4 Function Setting PRESET PAN AUTO SCAN AUTO CRUISE AUTO PATTERN IDLE MOTION TIME TASK NEXT PAGE BACK EXIT Please go back to main menu and move the cursor to FUNCTION SETTING click confirm button You can see the above interface PRESET Move the cursor to PRESET and then click confirm button to go to the third submenu PAN Move the cursor to PAN and then click confirm button to go to the third submenu AUTO SCAN Move the cursor to SCAN and then click confirm button to go to the third submenu AUTO CRUISE Move the cursor to AUTO CRUISE and then click confirm button to go to the third submenu AUTO PATTERN Move the
Download Pdf Manuals
Related Search