User Manual IDK-1115P-40XGC1E
Contents
1. 1 Li 118 35 H 152 85 1 5 Absolute Maximum Ratings 1 5 1 Absolute Ratings of Environment Value Symbol Min Max Unit Note Operating Ambient Top 20 70 C Temperature Storage Temperature 20 75 C 4 Note 1 Temperature and relative humidity range is shown in the figure below 2 90 RH Max Ta lt 40 3 Wet bulb temperature should be 39 C Max Ta 40 C 4 Humidity 896 9096 5 No condensation 1 5 2 Electrical Absolute Ratings 1 5 2 1 TFT LCD Module Value Item Symbol Min Max Unit Note Power Supply Voltage VCC 0 3 4 V 1 3 IDK 1115P User Manual 1 5 2 2 Backlight Unit Value Item Symbol Min Max Unit Note Converter Voltage Vi 0 3 18 V 1 2 Enable Voltage EN 5 5 V Backlight Adjust ADJ 5 5 V Note 1 Permanent damage to the device may occur if maximum values are exceeded Function operation should be restricted to the conditions described under Normal Operating Conditions 2 Specified values are for lamp Refer to 3 2 for further information 1 6 Block Diagram TFT LCD PANEL 1024x3x768 RXO 1 LVDS RX2 1 2 RECEIVER DC DC CONVERTER amp EEN REFERENCE VOLTAGE CONVERTER CONNECTOR LED BACKLIGHT Connector 3823K F05N 00L H 1 35mm Spin Entery UNIT Figure 1 1 TFT LCD module RX3 RXCLK vcc SEL68 DI YIAIJO NYOS 3 z4 zo o 8 2 m 29 KI TO E2. 0 3 TF 17 22 White Variation SW 0x 0 0y 0 123 14 5 6 Viewing Horizontal gt 10 70 80 Deg 1 5 Angle 0X USB2000 70 80 Vertical 60 70 60 70 IDK 1115P User Manual 28 Note 1 Definition of Viewing Angle 12 o clock direction 6 o clock 8x 90 6y 90 Note 2 Definition of Contrast Ratio CR The contrast ratio can be calculated by the following expression Contrast Ratio CR 1255 10 L255 Luminance of gray level 255 LO Luminance of gray level 0 CR CR 5 CR X is corresponding to the Contrast Ratio of the point X at Figure in Note 6 Note 3 Definition of Response Time TR TF Gray Level 255 Gray Level 255 90 Optical Response Gray Level 0 10 0 lt gt gt Time Te Tr Sd amp oO 66 67ms 66 67m Note 4 Definition of Luminance of White LC Measure the luminance of gray level 255 at center point LC L 5 L x is corresponding to the luminance of the point X at Figure in Note 6 29 IDK 1115P User Manual Note 5 Measurement Setup The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change during measuring In order to stabilize the luminance the measurement should be executed after lighting Backlight for 20 minutes in a windless room LCD Module _ LCD Panel USB2000 CS 1000T Center of the Screen 500 mm Note 6 Definition of W
3. IDK 1115P User Manual 4 Electrical Characteristics 2 1 TFT LCD Module Value Parameter Symbol Min Unit Note Power Supply Voltage 3 0 3 3 3 6 V Ripple Voltage 100 Rush Current InusH 2 0 A 2 Power Supply Cur White 1c x 410 510 mA 3 a rent Black c 590 690 mA 3 b Differential Input H Level Vu 100 mV Voltage for LVDS Receiver L Level 100 S p Threshold Terminating Resistor 100 Ohm Note1 The module should be always operated within above ranges Note2 Measurement Conditions lt 3 3V Note 3 The specified power supply current is under the conditions at Vpp 3 3 Ta 25 2 C DC Current and f 60 Hz whereas a power dissipation check pattern below is displayed IDK 1115P User Manual 6 2 2 a White Pattern Active Area Backlight Unit b Black Pattern Active Area Value Parameter Symbol Min Typ Max Unit Note Converter Power Supply Voltage Vi 10 8 12 0 132 V Converter Power Supply Current li 0 73 083 O Vi 12V Duty 100 Backlight Power Consumption Ppp 8 76 W Vi 12V Duty 100 EN Control Level Backlight on 2 0 3 3 5 0 V Backlight off 0 0 8 V PWM High 2 0 3 3 5 0 V PWM Control Level PWM Low 0 0 15 Level PWM Control Duty Ratio 1 100 200Hz PWM Control Frequency fpwM 190 2
4. User Manual IDK 1115P 40XGC1E TFT LCD 15 XGA LED Backlight AD ANTECH Enabling an Intelligent Planet Copyright The documentation and the software included with this product are copyrighted 2012 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements AMI is a trademark of American Megatrends Inc IBM and PC are trademarks of International Business Machines Corporation Intel Core 2 Quad Pentium Dual Core and Celeron are trademarks of Intel Corpo ration WinBond is a trademark of Winbond Corporation All other product names or trademarks are properties of their respective owners Part No 2006111510 Edition 1 Printed in China Jun 2012 IDK 1115P User Manual ii Message to the Customer Advantech Customer Services Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of indus tria
5. top surface Oil Ammonia Glass Cleaner Mayonnaise Ketchup Wine Salad Oil Vinegar Lipstick etc Temperature Condition Test Following test are performed in the condition with no dew condensation Cold Test Tested after leaving the parts in 40 C 3 C for 240 hours and in the room temperature for 2 hours Heat Test Tested after leaving the parts in 75 C 3 C for 240 hours and in the room temperature for 2 hours Humidity Test Tested after leaving the parts in the temperature 60 C 3 C humidity 90 to 95 for 240 hours and in the room tempera ture for 2 hours Cycle Test Tested after 5 cycles of leaving the parts in the temperature 30 C 3 C for 1 hour and in the room temperature for 0 5 hours then leaving the parts in the temperature 70 C 3 C for 1 hour and in the room temperature for 0 5 hours IDK 1115P User Manual 18 5 5 5 6 5 6 1 5 6 2 Judgment Must satisfy the following Function Operate properly Appearance Must satisfy the specification General Specification Item Specification 1 Frame size 323 5 0 3 X 252 3 0 3 mm 2 View Area 306 6 0 3 X 232 2 0 3 mm 3 Active Area 305 0 3 X 229 0 3 mm 4 Total Thickness 2 35 0 3 mm 5 Tail length 60 0 3 mm Mounting Notes Projected capacitive touch screen detects the touched locations by measuring the increased amount of the capacitance value between its electrodes at inputs Once it is built into a system capacitance couplings
6. 2 years Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain RMA return merchandise authorization number from your
7. Serial Transfer Rate 57 600bps nterface RS232C Data Format 8bit Stop Bit 1bit Parity None Spec USB Specification 1 1 Interface Full Speed USB HID Digitizer Device Communicating to Windows 7 Device class Vendor definition Communicating to other computers Coordinate Output Rate point sec 200p s Single touch 50set s 2 point touch 2point set Dual touch is supported Coordinate Resolution 11bit 2048 x 2048 The origin of theoretical coor Left side of the top X 0 Y 0 dinate Max height of components 5 5 mm Top side of the board EXC7237 Mas 52 x 40 Channels of wire Dimension 125 x 28 mm Windows 7 HID Digitizer device USB Windows USB RS232C 2000 Xp Vista 7 Supported Operating System CE Embedded Linux USB RS232C Mac USB QNX RS232C IDK 1115P User Manual 24 6 2 Touch controller physical specification 6 2 1 Interface Connection to the Host Computer Di IX GND e e GND VDV V 5V 8 gt USB RS232C 125 0mm 1 1 Beat inner y nen y P g Be E Sa CHIEN 3 0 Zo 26 rare DT e D 2 xx ETIENNE CN Terminal Function Remarks 1 GND Ground For USB 3 V 5v 5v Power or USB Vbus 5 GND Ground Connection to the 7 D USB D Host
8. are continually yielded among the touch screen FPC tail controller board and metal Chassis When turned on our projected capacitive touch screen will automatically adjust its sensitivity level to the surrounding environment at the standby state in order to avoid the affects by the surrounding capacitance couplings If surrounding environment changes or materials to alter the electrical field a large capacitor power supply unit LCD panel or materials with high dielectric constant is near these external factors will adversely affect the function of the touch screen to detect the correct input positions At structure design please refer to the mounting notes below and ensure enough gap distances among each component in order to avoid the external factors described above Mounting Fix the touch screen firmly so that the gap distances between the touch screen and other components will not be affected by touching or will not change with the passage of time An unexpected input may be caused if the gap is too narrow The locations on which a certain gap distance is required are as follows m Between LCD panel and touch screen L1 m Between touch screen and the surface of the bezel L4 m Between touch screen and the back of the bezel L2 m Between tail and LCD panel tail and metal chassis L3 amp L5 an insulating tape can be used In case of using capacitive sensor outside the moisture may cause the trouble Mounting Touch screen o
9. dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer IDK 1115P User Manual iv Contents Chapter Chapter Chapter Chapter Chapter Chapter 2 1 2 2 3 1 3 2 3 3 4 1 4 2 6 6 1 6 2 Overview cene nnne nnns 1 General Description 2 Display Characteristics cde 2 Mechanical Specification nn 2 Mechanical Dimension 3 Absolute Maximum Ratings 3 1 5 1 Absolute Ratings of Environment 3 1 5 2 Electrical Absolute Ratings 3 Block Di Ez NN EET I 4 Figure 1 1 TFT LCD module 4 Electrical Characteristics 5 TFT LGD Module a een ae a eagle 6 Ba cklight Unit mee rrr 7 Input Terminal Pin Assignment 9 CCD Module ee 10 Table 3 1 Symbol Description 10 Backlight Unit Converter Connector Pin 10 Color Data Input Assignment 11 Interface Timing 13 In
10. specifications are shown as the following table and timing dia gram Signal Item Symbol Min Max Unit Note DCLK Pixel Clock 17 65 80 2 Vertical Total Time Ty 780 806 1200 TH DE Vertical Address Time 768 768 768 TH Horizontal Total Time TH 1140 1344 1600 Horizontal Address Time Tup 1024 1024 1024 Note Because this module is operated by DE only mode Hsync and Vsync input sig nals should be set to low logic level or ground Otherwise this module will operate abnormally INPUT SIGNAL TIMING DIAGRAM TIMING DIAGRAM of LVDS T gt Se 7 SS RxCKIN Rx IN3 RUTA Kan roumi ROUTIO RUT RESERVED BO BOS Go Rx IN2 Fatz Fetz Romi ROTH Remis DE GND GND B05 Bo2 Rx INI Bot GOS G04 Gos Go G01 nemo CC nore noon gt R05 RO R01 IDK 1115P User Manual 14 4 2 Power On Off Sequence To prevent a latch up or DC operation of LCD assembly the power on off sequence should be as in the diagram below Power ON OFF sequence Note 1 Please avoid floating state of interface signal at invalid period Note 2 When the interface signal is invalid be sure to pull down the power supply of LCD to 0 V Note 3 The Backlight converter power must be turned on after the power supply for the logic and the interface signal to be val
11. 0 0 0 0 1 11111 1 1 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 11000000 0 0 1 1 1 1 11 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Gray Red 0 000000000000000000000000 Scale Dark 000000010000000000000000 Of Red Red 1 00000010000000000000 0 0 0 0 Red 2 DO HE S Uh ho A D SE EE Eo ww Ge amp 111111010000 0 0 0 0 Red252 1 1 1 1 1 1 1 0000 0 0 Red 252 1 1 1 1 1 1 1 10000 00 00 Red 252 Gray 0 0 0 0 0 0 0 0 Scale Dark 000000000000 1 0 0 0 Green 0 0 0 0 0 0 0 0 1 0 Green Green 2 CS F ok 3 0 0 0 0 0 0 0 0 1 1 1 1 1 1031000000 0 0 Green 252 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1000000000 Green 252 0 0 0 0 0 0 0 0 1 1 1 1 111100000000 Green 252 Gray Blue 0 000000000000000000000000 Scale Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 Blue 1 0000000000000000000 0 Blue 2 c LE CR OR Sh ue US Xo X 000000000000000001 1 1 1 1 1 1 Blue 252 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 11 11 1 0 Blue 252 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 252 Note 0 Low Level Voltage 1 High Level Voltage IDK 1115P User Manual IDK 1115P User Manual 12 Chapter 4 Interface Timing 4 1 Input Signal Timing Specifications The input signal timing
12. 00 20k Hz 2 LED Life Time LL 50 000 Hrs 3 Note1 LED current is measured by utilizing a high frequency current meter as shown below Input Power Pav Vi li y Power Supply GND Converter LED Backlight Unit Note2 At 20k Hz PWM control frequency duty ratio range is restricted from 20 to 100 Note3 The lifetime of an LED is defined as the time when it continues to operate under the conditions at Ta 25 2 and Duty 100 until the brightness becomes lt 50 of its original value Operating an LED under a high temper ature environment will reduce its life time and lead to color shift IDK 1115P User Manual IDK 1115P User Manual Input Terminal Pin Assignment 3 1 TFT LCD Module Pin No Symbol Description Polarity Note 1 VCC Power Supply 3 3V typical 2 VCC Power Supply 3 3V typical 3 GND Ground 4 NC No Connection 5 RXO LVDS Differential Data Input Negative 6 RX0 LVDS Differential Data Input Positive 7 GND Ground 8 RX1 LVDS Differential Data Input Negative 9 RX1 LVDS Differential Data Input Positive 10 GND Ground 11 RX2 LVDS Differential Data Input Negative 12 RX2 LVDS Differential Data Input Positive 13 GND Ground 14 RXCLK LVDS Differential Data Input Negative 15 RXCLK LVDS Differential Data Input Positive 16 GND Ground 17 RX3 LVDS Differential Data Input Negative 18 RX3 LVDS Differential Data Input Positiv
13. Computer 9 D USB D Compatible with 2 GND Ground For JST S10B PHDSS 4 V 5v 5v Power RS232C 6 GND Ground 8 TX RS232C TXD 10 RX RS232C RXD Ji Connection to the Touch Screen J2 Connection to the Touch Screen 9680014728 has both serial and USB interfaces and can support either communica tion port USB and serial interfaces cannot be used simultaneously 25 IDK 1115P User Manual IDK 1115P User Manual D nx 10 D TX GND GND V 5V V 5V GND GND 2 USB RS232C 26 Optical Characteristics 2 Test Conditions Symbol Value Unit Ambient Temperature Ta 25 2 Ambient Humidity Ha 50 10 9c RH Supply Voltage Voc 3 3 V Input Signal According to typical value in 3 ELECTRICAL CHARACTERISTICS Converter Voltage Vi 12 V Converter Duty 10096 Optical Specifications The relative measurement methods of optical characteristics are shown below The following items should be measured under the test conditions and stable environ ment shown in Note 5 Item Symbol Conditions Min Typ Max Unit Note Color Red Rx 0 0 Typ 0 604 Typ 1 5 Chromaticity Ry CS 1000T 0 05 0356 0 05 Green Gx 0 338 Gy 0 590 Blue Bx 0 148 By 0 098 Green Wx 0 313 Wy 0 329 Center Luminance of Lc 300 400 cd m 4 5 White Contrast Ratio CR 450 700 2 5 Response Time 8 13 ms 0x 2 0
14. e 19 GND Ground 20 SEL68 LVDS 6 8 bit select function control Note 3 High 6bit Input Mode Low or NC 8bit Input Mode Note1 Connector Part No STM MSB240420G Enter 3804K F20N 10L or equiva lent Note2 User s connector Part No STM P240420 Enter H204K D20N 02B or equiv alent Note3 Low stands for OV High stands for 3 3V NC stands for No Connection 3 2 Backlight Unit Converter Connector Pin Pin Symbol Description Remark 1 Vi Converter input voltage 12V 2 VEND Converter ground Ground 3 EN Enable pin 3 3V 4 ADJ Backlight Adjust PWM Dimming Hi 3 3VDC Lo OVDC 5 NC Not Connect Note1 Connector Part No 3808K FO5N 03L Enter or equivalent Note User s connector Part No H208K PO5N 02B Enter or equivalent IDK 1115P User Manual 10 3 3 Color Data Input Assignment The brightness of each primary color red green and blue is based on the 8 bit gray scale data input for the color The higher the binary input the brighter the color The table below provides the assignment of color versus data input Color Data Signal Red Green Blue R7 R6 R5 R4 R3 R2 RO R7 R6 G5 G4 G3 G2 G1 GO R7 R6 BS B4 B3 B2 BO Basic Black 000000000000000000000000 Colors Red Green 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue 0 0 0 0 0 0 0 0 1 1 1 1 111100000000 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 11 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 11 1 1 1 1 1 1 1 1 1 1 Yellow 111 1 1 1 1 1 0 0 0 0
15. een and LCD panel L3 1mm Gap LCD panel and Flat Surface Design If the Flat Surface Design is preferred please consult with us before proceeding Thickness of cover glass and capacitance couplings at the periphery of the touch screen must be considered for each individual case IDK 1115P User Manual 20 Touch Screen L1 1mm Gap between Touchscreen and LCD panel Display L31521mm Gap LCD panel and Tail 5 6 5 Tolerance There is a tolerance of 0 2 to 0 3mm for the dimensions of the touch screen and tail A gap must be made in the case and the connector to absorb the tolerance Bezel gt e 5 6 6 Tail The tail must not be forcibly stressed or bent too hard The conduction in the insulated area and wire breaking may be caused X 43 21 IDK 1115P User Manual IDK 1115P User Manual 22 Chapter 6 Touch Controller 6 1 9680014728 is controller board that works as coordinates generator for projected capacitive touch screen This controller board supports both USB and RS232C 9680014728 is lead free and compliant with RoHS Specifications Item Rating Remarks Operating Temp 20 C to 80 C No dew condensation Storage Temp 20 C to 85 C No dew condensation Relative Humidity 95 at 60 C RH Non condensation Supply Voltage DC 5 0V 5 50mV peak to peak maximum ripple and noise Consumption Current 50mA typ Format Asynchronous
16. hite Variation SW Measure the luminance of gray level 255 at 5 points Maximum L 1 L 2 L 3 L 4 L 5 Minimum L 1 L 2 L 3 L 4 L 5 AN Horizontal Line i 0 02 304 Vertical Line Active Area IDK 1115P User Manual 30 Light Shield Room Ambient Luminance lt 2 tux 9 Test Point X 1105 Handling Precautions B 1 Handling Precautions The optical characteristics are measured under stable conditions at 25 C Room Temperature 1 2 Since front polarizer is easily damaged pay attention to scratch Be sure to turn off power supply when inserting or disconnecting from input con nector Wipe off water drop immediately Long contact with water may cause discolora tion or spots When the panel surface is soiled wipe it with absorbent cotton or other soft cloth Since the panel is made of glass it may break or crack if dropped or bumped on hard surface Since CMOS LSI is used in this module take care of static electricity and insure people are earthed when handling Do not open or modify the Module Assembly Do not press the reflector sheet at the back of the module to any directions In case if a Module has to be put back into the packing container slot after once it was taken out from the container please press at the far end of the LED light bar reflector edge softly Otherwi
17. id The Backlight converter power must be turned off before the power supply for the logic and the interface sig nal to be invalid Parameter re Unites Min T1 0 5 10 ms T2 0 50 ms T3 0 50 ms T4 500 ms T5 200 ms T6 200 ms T7 5 300 ms T8 10 ms T9 10 ms 15 IDK 1115P User Manual IDK 1115P User Manual 16 Chapter 5 Touch Screen 5 1 5 2 5 3 5 4 Touch Characteristics This specification is applied to the Projected Capacitive EXC series Electrical Characteristics Specification Value Maximum Voltage DC6V Recommended touch gt 10mm contact area Mechanical Characteristics Specification Value Operating Life Input finger 50 000 000 hits Light Transmittance 91 typical value at full wavelength Surface Hardness Over 5H by JIS pencil hardness Electrode Matrix Pitch Approximately 5 7mm Environment Characteristics Specification Value Operating Temperature 20 C to 70 no condensation Operating Humidity 20 C to 60 Less than 90 RH no condensation Exceeding 60 C Less than 133 8g m3 no condensation Storage Temperature 40 C to 75 C no condensation Storage Humidity 40 C to 60 C Less than 95 RH no condensation Exceeding 60 C Less than 142 9g m3 no condensation Chemical Resistance Toluene Trichloroethylene Acetone Alcohol Gasoline Machine
18. l environments Whether your new Advantech equipment is destined for the labo ratory or the factory floor you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known Your satisfaction is our primary concern Here is a guide to Advantech s customer services To ensure you get the full benefit of our services please follow the instruc tions below carefully Technical Support We want you to get the maximum performance from your products So if you run into technical difficulties we are here to help For the most frequently asked questions you can easily find answers in your product documentation These answers are nor mally a lot more detailed than the ones we can give over the phone So please consult this manual first If you still cannot find the answer gather all the information or questions that apply to your problem and with the product close at hand call your dealer Our dealers are well trained and ready to give you the support you need to get the most from your Advantech products In fact most problems reported are minor and are able to be easily solved over the phone In addition free technical support is available from Advantech engineers every busi ness day We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products iii IDK 1115P User Manual Product Warranty
19. n a display It is recommended to use an insulating resin material for the bezel Ensure the gap between the touch screen and front bezel L4 If a metal plate is used for the bezel unintended capacitance couplings may occur on the periphery of the active area If a metal material is used for bezel ensure the gap of approximately 2mm between touch screen and bezel L2 19 IDK 1115P User Manual 5 6 3 5 6 4 In order to avoid the gap distance L1 from being changed with the passage time it is recommended to apply the adhesive tape onto all the 4 sides with no space fully sealed when gluing the touch screen L4 2mm L2 2mm Gap between Touchscreen and Bezel if the bezel is made of matal L1 1mm Gap between Touchscreen and LCD panel Fig 4 5 1 1 L3 1mm Gap LCD panel and Mounting touch screen on back side of the bezel It is recommended to use an insulating resin material for the bezel Ensure the gap between the touch screen and front bezel L4 If a metal plate is used for the bezel unintended capacitance couplings may occur on the periphery of the active area If a metal plate or any other metallic materials is used for the bezel ensure the gap distance of approximately 2mm between the touch screen and bezel L2 Fix the touch screen firmly so that the gap distance L1 will not be affected L42mm L2 2mm Gap between Touchscreen and Bezel if the bezel is made of matal L1 1mm Gap between Touchscr
20. put Signal Timing Specifications 14 Power On Off Sequence 15 Touch Screen 17 Touch Re Ee 18 Electrical Characteristics 2 eai text th end 18 Mechanical Characteristics 18 Environment Characteristics 18 General Specification eiit ete 19 Mounting Notes iiiter E e nint x eae oM Rein 19 5 6 1 Y TT y LL pt 19 5 6 2 Mounting Touch screen on a 19 5 6 3 Mounting touch screen on back side of the bezel 20 5 6 4 Flat Surface Design 20 5 6 5 Tolerance eet 21 560 Tall 21 Touch Controller 23 eelere 24 Touch controller physical specification 25 6 2 1 Interface Connection to the Host 25 6 2 2 9680014728 dimension sess 25 V IDK 1115P User Manual A A 2 Appendix B B 1 IDK 1115P User Manual Optical Characteristics 27 Test Cond P 28 Optical Specifications 28 Handling Precautions 31 Handling Pr cautions en an 32 vi Chapter 1 Overview 1 1 General Description IDK 1115P 40XGC1E is a Color Active Matrix Liquid C
21. rystal Display composed of a TFT LCD panel a driver circuit and backlight system The screen format is intended to support the XGA 1024 H x 768 V screen and 16 2M 262k colors RGB All input signals are LVDS interface compatible Driver board of backlight is included 1 2 Display Characteristics The following items are characteristics summary on the table under 25 condition Items Specifications Unit Note Active Area 305 0 H x 229 0 V 15 0 diagonal mm 1 Bezel Opening Area 307 4 H x 231 3 V mm mm Driver Element a Si TFT active matrix E Pixel Number 1024 x R G B x 768 pixel Pixel Pitch 0 297 H x 0 297 W mm Pixel Arrangement R G B Vertical Stripe a Display Colors 16 194 277 262 144 color Display Mode Normally White Surface Treatment Hard Coating Anti Glare Haze 25 Module Power Consumption 10 8 Black pattern W Typical 1 3 Mechanical Specification Item Min Unit Note Module Size Horizontal H 329 4 mm Vertical V 259 7 S Depth D 14 6 S Weight 1300 9 IDK 1115P User Manual 2 1 4 Mechanical Dimension Unit mm Si 323 5 Touch 5 9 305 0 T S Active Area E 14 8 m y L z T8 3
22. se the TFT Module may be damaged At the insertion or removal of the Signal Interface Connector be sure not to rotate nor tilt the Interface Connector of the TFT Module After installation of the TFT Module into an enclosure do not twist nor bend the TFT Module even momentary At designing the enclosure it should be taken into consideration that no bending twisting forces are applied to the TFT Module from outside Otherwise the TFT Module may be damaged Small amount of materials having no flammability grade is used in the LCD module The LCD module should be supplied by power complied with require ments of Limited Power Source IEC60950 or UL1950 or be applied exemp tion IDK 1115P User Manual 32 ADWNTECH Enabling an Intelligent Planet www advantech com Please verify specifications before quoting This guide is intended for reference purposes only All product specifications are subject to change without notice No part of this publication may be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written permis sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies Advantech Co Ltd 2012
Download Pdf Manuals
Related Search