Product Manual:
Contents
1. 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 7 3 0 Configuration amp Components The PW series winch is designed to extend and retract a line from a drum for the tethering of a person that is performing a confined space entry operation The PW Series winch is designed with an internal braking system to prevent the accidental pay out of line as well as a back up locking pawl system to prevent free wheeling of the winch Line extension or retraction is controlled by the crank handle which is attached to the drive shaft SNAP HOOK 2 2 PART 121297 001 WARNING DECAL FROM DECAL KIT ITEM 6 ___ PART 500205 001 SERIAL NUMBER PLATE FROM DECAL KIT ITEM 6 The winch is available with a variety of adapter brackets These adapter brackets allow the winch to be easily secured to and removed from various Pelsue and other Bills manufacturer s rescue amp retrieval systems i e tripods davits etc Cable extension pay out should occur ONLY when the handle is turned counterclockwise clockwise for reverse rotation winches AND a force of AT LEAST 10 Ibs 4 5 kg is applied to the line When there is no tension on the line turning the handle counterclockwise clockwise for reverse rotation winches should NOT cause the drum to move If the drum rotates under these conditions the winch should be removed from service and sent to Pelsue for2. be invoiced as purchased subject to credit when the parts claimed to be defective have been received and examined by the factory This warranty is expressly in lieu of all other warranties expressed or implied including any warranties of mer chantability or warranties of fitness for any particular use and all other obligations or liabilities in connection with the sale of this equipment T A Pelsue Company 2500 South Tejon Street Englewood Colorado 80110 800 525 8460 Page 6 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 2 0 Introduction amp Product Information Congratulations on your choice of a Pelsue man rated confined space entry retrieval system winch to compliment your entry retrieval operation This equipment has been designed and manufactured to exceed confined space requirements and regulations to meet the needs of the discriminating operator for the efficient and safe entry or retrieval of personnel from a confined space Safe efficient and trouble free operation and maintenance for your component or system requires that you or anyone else who will be operating maintaining or inspecting the equipment read understand and follow all the safety installation operation maintenance and inspection instructions contained in this manual This manual covers the entire line of PW series winches manufactured by Pelsue Use the Table of Contents or Index as a guide to find specific informat
3. inspection and possible repair Cable retraction take up should occur when the handle is turned in the clockwise direction counterclockwise for reverse rotation winches WINCH DRIVE HANDLE WITH SPEEDER KNOB Below is a table showing the Winch Models of the PW Series with their corresponding chassis size cable length and cable types PART 121298 001 CRANK HANDLE SX DECAL FROM DECAL KIT ITEM 6 Figure 3a PW Series Winch WINCH CHASSIS CABLE CABLE Vertical Mounting View MODEL SIZE LENGTH TYPE PWO07C SMALL 70 21 3 m 3 16 STAINLESS WIRE ROPE SE PWO7R 70 21 3 m 1 2 SYNTHETIC ROPE 100 30 5 m 3 16 STAINLESS WIRE ROPE MEDIUM 150 45 7 m 3 16 STAINLESS WIRE ROPE 100 30 5 m SYNTHETIC 200 60 9 m 3 16 STAINLESS WIRE ROPE LARGE 300 91 4 m 3 16 STAINLESS WIRE ROPE 150 45 7 m SYNTHETIC Table 3 PW Series Winch Models amp Specs ___ PART 121302 001 SPECIFICATION d DECAL FROM DECAL KIT ITEM F NOTE The PW winch is equipped with a safety mechanism which prevents the accidental pay out of large amounts of cable In the absence of constant tension on the cable the crank handle will continue to turn however cable WILL NOT pay off of the drum It will appear that the handle has come loose THIS IS NOT THE CASE It cannot come free of the shaft Simply turning the handle in a clockwise manner will cause the handle to pay in ca
4. on a regular basis Page 10 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 4 4 Operating Safety 10 11 12 Read understand and follow the User Manual and signs on the winch before using maintaining or inspecting the equipment Train all operators before allowing them to use the winch An untrained operator exposes themselves bystanders and workers to possible serious injury or death Visually inspect the winch and all auxiliary components and equipment before using Correct any problems before using the equipment Securely anchor the winch before using Use only certified anchor and connector components in your system Use only an approved full body harness for the workers Always work in teams One person works in the confined space and the other one pays out the line and reels it in Do not exceed 350 Ibs 160 kg on the line during operation Including tool belts etc Establish a regular training program for new and experienced workers Establish a detailed inspection program for your equipment and document the findings Return the equipment to the manufacturer for re work if any problems are found Plan your work program before starting Have the required people equipment and procedures available to do the job Do not use the equipment around physical or environmental hazards This list includes but is not limited to Corrosion that may affect the structural int
5. required at all times the entrant and winch operator Always maintain communication to be sure the lifeline is kept taut and that the entrant is not encountering problems f Emergency During rescue or emergency procedures the winch anchorage must be capable of supporting at least 1500 Ibs 680 kg Always use an approved harness when moving people People be seriously injured during rescue or in an emergency situation if they are not supported in an approved harness However quick response is required in any emergency or rescue operation 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 1 5 5 5 Field Operation continued 4 Personal Fall Arrest System PFAS In some entry retrieval applications OSHA ANSI and local standards require that the entrant be connected to a Personal Fall Arrest System It is the responsibility of the operator to be aware of these requirements and follow them Always use a full body harness on the entrant when attached to a PFAS to minimize potential injury to the entrant Application limitations for the winch also apply to a PFAS 5 Installation Removal The Pelsue PW series man rated winches are most commonly used on or with a Pelsue Davit System Normally the winch is removed from the davit for storage and transporting When installing or removing the winch from the davit follow this procedure a Installing i Be sure quick connect mounting brackets
6. using the winch follow this procedure 1 Review and follow the Pre Operation Inspection Refer to Section 5 3 2 Inspect the unit prior to each use Visually check each component to be sure that there is no damaged or missing parts Check that all systems and components function as intended Do not use the equipment if any problems are found 3 Work Planning Plan your entire work project before starting Consider all the equipment and system requirements and comply with these requirements before starting Anticipate the needs before during and after the project is being done and prepare for these needs Be prepared for the unexpected by planning in advance Your advance planning list includes but is not limited to a Anchorage We recommend mounting the winch to other Pelsue supporting components and systems to be sure that the anchorage has sufficient strength Pelsue support and mounting systems are designed to ANSI and OSHA standards Refer to Structural Manual for specific strengths When using other manufactures anchorages be sure they meet OSHA or local requirements b Connectors Connectors if used should be equipped with an anti rollout device to prevent accidental disengagement Rollout can occur when there is interference between the connector and load that causes the gate or keeper to accidentally open or release Do not take a chance with safety Only use approved components c Hazards Stay away from mechanical chemical
7. wires in most cases Although there is no simple sure way to tell when corrosion has excessively weakened the cable the inspec tion personnel must keep in mind that corrosion normally develops on the inside of the cable before it becomes visible on the outside Have a qualified person assess the damage and determine whether the unit should be removed from service Pitting is a particularly serious sign of advanced corrosion Rust along with broken wires in a given area is sufficient reason to remove the unit from service iv v Insufficient Lubrication Check for insufficient lubrication of the cable Generally this is caused by a build up of contamination between the strands of cable Packed grease dirt paint or other contaminants prevent the lubricant from getting inside the cable to prevent internal friction and corrosion If contaminants have filled the grooves remove from service REPLACE THE CABLE IF THERE ARE 3 OR MORE BROKEN WIRES IN THE CABLE 2 OR MORE BROKEN WIRES IN ONE STRAND IN ONELAY REDUCED NORMAL DIAMETER DIAMETER FLEXING CAN REVEAL T HIDDEN BREAKS igure 9J Figure 6i Page 26 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 6 2 Inspection continued LLL LLL ee as vi Snagged Wires and Crushed or Flattened Strands Check for snagged wires and curved or flattened stands These conditions appear when the cable has been pulled around corne
8. 0 will address the basic operation and usage of a Pelsue PW Series Man Rated winch Throughout this sec tion and during operation of the PW winch the operating safety section of this manual should be constantly referred to and the points address therein should be continually adhered to during all operation These points have been repeated below OPERATING SAFETY 12 Do not use the equipment around physical or Read understand and follow the User Manual and signs on the winch before using maintaining or inspecting the equipment Train all operators before allowing them to use the winch An untrained operator exposes themselves bystanders and workers to possible serious injury or death a Visually inspect the winch and all auxiliary components and equipment before using Correct any problems before using the equipment Securely anchor the winch before using Use only certified anchor and connector components in your system Use only an approved full body harness for the workers Always work in teams One person works in the confined space and the other one pays out the line and reels it in environmental hazards This list includes but is not limited to W Corrosion that may affect the structural integrity of the lifeline or other components W Chemicals which can degrade components in a manner not visually indentifiable Toxic gases Rescuers or workers can be killed in toxic environments Heat or el
9. 08 6 0 Maintenance amp Inspection MAINTENANCE amp INSPECTION 1 Read understand and follow the User Manual and signs 3 Keep instructional and safety signs clean and legible at on the winch before using maintaining or inspecting the all times Clean or replace as required equipment 4 Lubricate winch as per instructions in Section 6 ANSI and OSHA require a regular inspection program for all confined space entry retrieval equipment and to main tain documented results of these inspections Follow the inspection procedure contained in this manual and use the inspection form to document the results 5 Remove the equipment from service if a problem is found during the inspection Return to an authorized repair depot or the factory for service 6 1 Maintenance r The following section will address preventative maintenance points of service that performed periodically will drastically increase the working life of the PW Series Man rated winch Preventative maintenance will ensure that the PW series man rated winch is always in optimum working condition LUBRICANTS 1 Grease Use a SAE multi purpose high temperature grease with extreme pressure EP performance Also acceptable is a SAE multi purpose lithium base grease 2 Cable Clean with WD 40 or other light de greaser and wipe with clean rag MAINTENANCE INTERVALS Daily 1 Visual Inspection Perform a complete visual inspection Remove from s
10. 1 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 3 1 e T A Pelsue Company 2500 South Tejon Street Englewood Colorado USA 80110 Toll free 800 525 8460 or 303 936 7432 Fax 303 934 5581 ISO 9001 Ce rtifi ed Internet www pelsue com Email sales pelsue com
11. ARNING Do not use the winch if turning the handle counter clockwise pays out cable when there is no load applied Slack may develop in the cable and a fall in this situation can result in damage to the winch as well as injury or death to the personnel Immediately return the winch for inspection c Wearing gloves place hand on the lifeline to guide it as it extends Use your hand to maintain a slight pull on the cable at all times d For a vertical entry maintain the swing angle at less than 30 degrees while working The entrant can be seriously injured if the swing angle exceeds 30 degrees See Figure 5h e If the entrant is not suspended and there is NO chance of a fall pay out sufficient line 2 ft or 6 m max so it is slack and the entrant can work Hold the lifeline so there is a slight pull on it at all times f Extend or retract the lifeline as required to keep the line snug g Maintain communication between the entrant and attendant at all times Be sure each knows what the other is doing h Do not go around corners when entering a confined space Body parts clothing tools or other items can get snagged when going around a corner and over obstacles during the retrieval procedure Corners or sharp edges can also damage the lifeline as it goes by Be prepared to do an entry rescue to assist in the retrieval of a down entrant i If the lifeline becomes tight or slack during entry communicate with the entrant to determine w
12. Do not pull on an end or wire with pliers It can pull the broken end out to expose it LAY LENGTH STRAND WIRE ONE REVOLUTION OF A STRAND ABOUT THE CORE Figure 6f Figure 6g Figure 6h 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 25 6 2 Inspection continued Use the previous inspection logs to determine the total number of broken wires in a lay See Fig 19 Remove the cable and winch from service when There are 3 or more randomly distributed broken wires in the cable There are two or more broken wires in one strand in one lay There are any broken wires within 1 0 inches 25 mm of the cable clamps next to the thimble Return the winch to the factory for cable replacement if any of these conditions are met or exceeded ii Worn or Abraded Wires Check for worn or abraded wires Worn or abraded wires are caused by friction and rubbing against adjacent components and are usually brighter in appearance Remove from service if any surface wires in one area are worn by 1 3 or more of their diameter iii Bulges or Reduction in Diameter Check for bulges or a reduction of the cable diameter When these conditions occur it indicates serious internal cable damage Remove the unit from service when the cable diameter increases or decreases by 0 05 inches 1 3 mm See Fig 20 Corrosion Check for corrosion Corrosion can be seen as a discoloration of the
13. ENSURING CUSTOMER SATISFACTION IS ONE OF THE DIFFERENTIATORS THAT SETS YOU APART FROM THE PACK AND YIELDS A COMPETITIVE ADVANTAGE THEREFORE WE WILL SUPPORT TOTAL CUSTOMER SATISFACTION BY IMPLEMENTING THE ISO 9001 QUALITY SYSTEM AND PROVIDING THE NECESSARY ATMOSPHERE AND TRAINING TO NURTURE THIS CONCEPT THROUGHOUT OUR ORGANIZATION WE WILL MAKE EVERY BUSINESS DECISION AS THOUGH THE QUALITY OF THE PART OR SERVICE PROVIDED WAS DESTINED FOR OUR OWN OR OUR FAMILY S USE WE WILL ALWAYS THINK QUALITY FIRST EVERY T A PELSUE COMPANY EMPLOYEE IS EXPECTED TO COMMIT TO THIS PHILOSOPHY IN THE PERFORMANCE OF HIS OR HER DAILY TASKS QUALITY FIRST T A PELSUE COMPANY SENIOR MANAGEMENT TEAM 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 5 1 2 Pelsue Product Warranty R Pelsue products are designed and engineered to perform as stated in published specifications Quality materials and workmanship are used in the manufacture of this product With regular maintenance and proper care Pelsue equipment provides many trouble free hours of operation The T A Pelsue Company warrants to the buyer that the Hoist Product furnished will conform to specifications and will be free from defects in material and workmanship from the date of shipment to the original buyer for a period of 3 months 90 days In the event of failure of any components of a Pelsue product within the warranty
14. Part 500138 001 Product Manual PW Series Man Rated Winch ISO 9001 Certified T A Pelsue Company 2500 South Tejon Street Englewood Colorado USA 80110 Tel 800 525 8460 or 303 936 7432 Fax 303 934 5581 Internet www pelsue com Email sales pelsue com PELSUE ince our inception in 1963 the T A Pelsue Company has designed and manufactured high quality equipment to improve the personnel effi ciency and working conditions in various under ground confined and outdoor areas Founded by T Allen Pelsue the company has estab lished a continuing reputation for excellence in the production of fine products for a broad spectrum of industry throughout the world 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 ISO 9001 Certified Now in our second generation of family direction continued commitment to innovation and quality makes Pelsue a leading source of equipment for many types of confined spaces We specialize in safety retrieval fall arrest ventilation cable placing splicing and maintenance nationally and abroad With more than 70 000 square feet of facil ities available Pelsue continues the dedication that has made us pre eminent in this field Page 3 Table of Contents Page 4 Section Description Page uu usss ss General Information 5 ette Quality Policy E Pelsue P
15. TY Work SAFELY 4 1 Warning Statement uz xx s WARNING Products manufactured or sold by T A Pelsue Company are intended for use by professionals trained and experienced in the use inspection and maintenance of these products Paraprofessional users such as volunteer rescue workers and sportsmen involved in risk sports such as climbing and Failure to read and heed all labels and instructions may caving will be held to the same standard of experience and result in injury or death Inspect all components before training as professionals and after each use and remove from service if any damage or defect is found Keep product free from dirt and moisture Do not leave a suspended load i lling climbing and the training involv Technical rescue repelling climbing and the training involved unattended Do not exceed maximum rated loads are hazardous activities Each situation has its own unique conditions and must be evaluated Effective risk manage ment comes from experience proper training and good per sonal judgement 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 9 4 2 Safety Alert Symbol SAFETY ALERT SYMBOL This Safety Alert symbol means ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED The Safety Alert symbol identifies important safety messages on your Pelsue Retrieval Product and in the manual When you see this symbol be alert to the possib
16. ain inspect or work around the equipment be familiar with the operating and maintenance procedures and related safety information contained in this manual This manual will take you step by step through your working day and alerts you to all good safety and operating practices while using the system Remember you are the key to safety Good safety practices not only protect you but also the people around you Make these practices a working part of your safety program Be certain that everyone operating this equipment is familiar with the procedures recommended and follows safety precautions Remember most accidents can be prevented Do not risk injury or death by ignoring good safety practices System owners must give operating instructions to operators or employees before allowing them to use the equip ment and at least annually thereafter most important safety device on this equipment is a safe operator It is the operator s responsibility to read and understand all safety and operating instructions in the manual and to follow these All accidents can be avoided A person must understand the operation of this equipment and be trained in it s usage before operating the equip ment An untrained operator exposes himself and others to possible serious injury or death Do not modify the equipment in any way Unauthorized modification may impair the function and or safety and could affect the life of the equipment Think SAFE
17. and electrical hazards Moving machinery sharp edges or other mechani cal hazards can injure personnel damage equipment or interfere with the work procedure Chemical corrosive or toxic environments can damage equipment or affect the well being of personnel Electrical power can flow through the equipment and electrocute personnel even if there is no direct contact Sparks or electricity from welding may damage safety lines and cables Plan your work and rescue procedures to consider these fac tors and allow for them Advance planning will allow the equipment to be used safely in a variety of conditions d Cable Path Body parts clothing tools or other items can get entangled or snagged when going around a corner or over obstacles during the retrieval procedure Corners or sharp edges can also damage the lifeline as it goes by Ensure that the cable does not come into contact with a heat source or hot object that may damage it Cautions must be taken when more than one person is tied off separately to prevent the cables from becoming knotted together Do not step across another cable or lifeline Be prepared to perform an entry rescue to assist in the retrieval of a down entrant e Vertical Applications For vertical applications keep the swing fall angle less than 30 degrees Serious injuries to personnel can occur if they swing into a solid object Try to keep the entrant directly below the winch attachment point at all times Two 2 people are
18. any of the features stick or bind lubricate with a light oil If sticking or binding persists remove winch from service and return to the factory for service 3 Brake Engagement The internal brake must hold the cable from extending or retracting unless the crank arm is turned To functionally check this feature extend the cable in 10 foot 3 meter increments by turning the handle counter clockwise At each 10 foot 3 meter interval turn the handle clockwise until the cable just begins to retract again This tightens the handle against the brake pads Pull sharply on the cable to ensure that the brake pads are holding securely If they do not hold remove the winch from service and return to the factory for inspection and repair CAUTION During this inspection step if the handle is not turned back clockwise to engage the brake pads pulling on the cable will cause approximately 18 in 457 mm of the cable to pay out until the handle tightens by itself If the handle does not tighten immediately on its own remove the winch from service and return to the factory for inspection and repair 4 Brake Ratchet Mechanism The winch is designed with an internal ratchet that engages the brake when the crank arm is turned clockwise To fully engage the brake the crank must be turned in the clockwise direction until 2 clicks of the ratchet are heard If the ratchet does not click when the crank is turned clockwise remove from service and return to fa
19. are secured to structure Refer to appropriate Structure Manual for bracket mounting details See Figure 5a Figure 5a Davit System Winch Device Mount ii Attach the winch to the quick connect mounting bracket Raise the back frame plate over the anchor rod Align the hitch pin hole Secure the winch using the attached hitch pin See Figure 5b Figure 5b PW Series Winch Quick Connecting Sequence Page 1 6 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 5 5 Field Operation continued ssnc s rr r r lt K I iii Refer to Structure Manuals for detailed instructions on threading cable through systems iv Be sure the cable crimps thimble swivel and snap lock connectors are in good condition and functioning as intended See Figure 5c v Attach the snap hook to the entrant s full body harness See Figure 5d b Removal i When entrant is clear of hole disconnect the snap hook from harness Maintain at least a 10 Ib 4 5kg load on the cable to keep the cable tight ii Pull cable through all pulleys and rollers on structure See appropriate structure manual iii Turn the crank clockwise to retract the cable while maintaining a 10 Ib 4 5 kg pull on the cable iv Retract until the crimps and thimble just touch the drum CAUTION Winding the cable too far could cause damage to the winch as the snap becomes entangled with the level wind rollers Damage to the cab
20. ary components must be compatible to prevent creating unexpected hazards A list of system compatibility requirements includes but is not limited to 1 Anchorage The winch is designed to be attached to a Pelsue mounting and support system These systems do provide the required anchorage strength for the winch When using another system or anchorage method anchorage points must meet ANSI and OSHA standards or local regulations Qualified people are required to approve non standard anchorage systems before they are used 2 Connectors Use only approved connectors with sufficient capacity that have an anti rollout device designed into the snap Non approved connectors can open during use and create unexpected hazards Do not use them 3 Personnel Harness Use only an approved full body harness Do not use a single belt or strap system Only a full body harness can provide the required support for the body to prevent injury Page 1 4 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 5 5 Field Operation The Pelsue series man rated winches are designed for use in many applications including but not limited to personnel riding rescue or confined space entry retrieval It is the responsibility of the operator to be familiar with and follow all applicable OSHA and industry standards on operating guidelines for your project If you have any questions consult a qualified person or call the factory When
21. be used to tie an item off with a knot The only way to connect to the synthetic rope is by the snaphook Any rope that has a knot tied in it should be returned to the factory for replacement vi Heat Damage Torch Burns Electric Arcs Heat damage torch burns or electric arc strikes result in the outer jacket melting and becoming hard or brittle Often there is damage that is done to the inner core that may not be seen by the naked eye It is possible to completely sever a synthetic rope lifeline in an environment with several spark sources Extreme care must be taken under these circumstances and regular rope inspections should take place regularly throughout the day while working to ensure rope integrity Page 28 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 uad jurod jeq Buisn III4 400q uono2edsur eys 0 do uuoj ejduies zl c 341v5 3 5 320131v9 5 e 5 TAAIMS 2 E 2 gt NOISON30D I eo savaa p M MNOILOVALIN 5 BERE MOO NOISNALXA SAVAD STIANVH SUA FIOI ANIM THAT NOISOWAOD 45vNvad FRAME amp HOUSING STAVIT SUUNALS Va YOLIAdSNI NOLLO IdSNI HO ALVA ALVA OA 6 ON TAGON Page 29 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 6 4 Winch Cable Ins
22. ble after a maximum of five 5 revolutions before the lifting brakes are once again engaged 27 4 Figure 3b PW Series Winch Non Drive Side View Page 8 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 4 0 Safety Section 4 0 will deal with safety procedures and precautions that are to be addressed and adhered to when employing Pelsue PW series winches or any other piece of rescue and retrieval equipment SIGNAL WORDS Note the use of the signal words DANGER WARNING and CAUTION with the safety messages The appropriate signal word for each message has been selected using the following guidelines DANGER Indicates an imminently hazardous situation that if not avoided will result in death or serious injury This signal word is to be limited to the most extreme situations or for hidden or unseen hazards WARNING Indicates a potentially hazardous situation that if not avoided could result in death or serious injury and includes obvious and hidden hazards It may also be used to alert against unsafe practices CAUTION Indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices You are responsible for the safe operation maintenance and inspection of your Pelsue man rated confined space entry retrieval system You must ensure that you and anyone else who is going to operate maint
23. ctory for re work The ratchet should be silent when the crank is turned counter clockwise If the ratchet clicking is heard when the crank is turned counter clockwise remove from service and return to the factory for inspection and repair 6 2 3 DETAILED INSPECTION A detailed inspection should be done on the winch every year and more often if used extensively The inspection must include the following results logged on the sample inspection form and retained in your files should anyone ask to see them Refer to section 6 2 4 for a sample inspection form The detailed inspection should include 1 Visual Inspection Refer to section 6 2 1 for a listing of all items that should be checked visually Log the results on the inspection form 2 Functional Inspection Refer to Section 6 2 2 for a listing of all items that should be functionally checked Log the results ontheinspec tion form 3 Detailed Inspection a Cable Fittings Snap Hook Check the cable fitting on the end of the lifeline Be sure that it is not cracked distorted bent corroded worn loose or cutting into the cable Be sure the cable and strands are not frayed or broken Check the snap hook Be sure it is not bent distorted cracked or worn Be sure the swivel turns freelyandthe gate lock and gate open and close easily Page 24 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 6 2 Inspection continued SS SSS eae
24. dition prior to using Equipment that is not in good condition can endanger the safety of the entrant during use The visual inspection must include but is not limited to the following items 1 Check that the winch has no structural defects 2 Be sure winch is clean and the labels are legible 3 Functional check a Pull on cable and turn crank counter clockwise to extend cable b Turn the crank clockwise until 2 clicks of the ratchet is heard to engage the brake c Release crank and pull hard on cable Crank should not move and cable should not extend d Pull on cable and turn handle clockwise to retract cable 4 Inspection of the wire rope cable a Check cable for fraying kinking cuts wear broken wires weld strike marks or any other defect which may affect the structural integrity of the cable b Check that the thimble and cable crimps are intact and in good condition c Check that the snap hook is in good condition Be sure that the gate will not open unless the lock is released The snap should also be free from rust as this is a sign of weakness 4 Inspection of the synthetic rope cable a Check cable for fraying kinking cuts wear cut outer sheath or jacket weld strike marks or a change in diameter of cable crushing or any other defect which may affect the structural integrity of the cable b Check that the thimble and cable crimps are intact and in good condition c Check that the snap hook is in good condition Be
25. egrity of the lifeline or other components Chemicals which can degrade components in a manner which can not be visually identified Toxic gases Rescuers or workers can be killed in toxic environments Heat or elevated temperatures Moving machinery Workers or auxiliary equipment can be contacted by or pulled into moving components Sharp edges Workers or the rescue equipment can be injured by or damaged by sharp edges or components Electrical hazards Stay away from power lines or components carrying electrical power e Overload Do not exceed 350 lbs 160 kg during operation Follow confined space regulations and standards 4 5 Maintenance amp Inspection Safety 1 Read understand and follow the User Manual and signs on the winch before using maintaining or inspecting the equipment 2 ANSI and OSHA requires a regular inspection program for all confined space entry retrieval equipment and to main tain documented results of these inspections Follow the inspection procedure contained in this manual and use the inspection form to document the results 3 Keep instructional and safety signs clean and legible at all times Clean or replace as required 4 Remove the equipment from service if a problem is found during the inspection Return to an authorized repair depot or the factory for service 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 1 1 5 0 Operation Section 5
26. ene Note results on inspection log b Cable Inspection The cable must be inspected over its full length and the results recorded in the inspection log Always wear heavy gloves to prevent cuts and slivers while handling the cable If any strands are broken remove from service i Check for broken wires Pull the cable out in small segments and flex to check for broken wires NOTE The inspection of the cable is all based on the definition of a lay core strand and wire A lay is where a strand makes one complete revolution around the core The core is the center of the cable itself A strand is the bundle of wires that move around the core A wire is a single filament that makes up a strand See Figures 6f and 6g Start the inspection at the cable clamp to check for broken wires or strands Pull out a short segment of cable and turn it while flexing to check for broken wires WARNING Review the cable inspection log to determine the location of previously found broken wires or other defects These previously found defects combined with those found during this inspection may require that the winch be removed from service Inspect the entire length of the cable logging the results on the inspection form When a broken wire is found remove the protruding end by flexing it back and forth along the length of the cable The wire will normally break off inside the cable so there are no exposed ends to damage adjacent strands See Figure 6h
27. ervice if a defect is found Weekly 1 Functional Inspection Perform a functional inspection Record results and keep documentation Bi Annually 1 Lubricate Shaft Bearings Using SAE 30W Oil a Pinion Shaft 3 locations See Figure 6a b Drum Shaft 2 locations See Figure 6a 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 2 1 6 1 Maintenance continued E 2 Lubricate the Cable Use WD 40 to lubricate the cable Lubricating oil should only be applied to a clean dry cable Use a stiff bristled brush to remove contaminants from the cable if it is dirty Allow the oil to penetrate into the cable to reduce internal fric tion Wipe the cable dry with a clean cloth as it is being retracted into the winch See Figure 6b Figure 6a Figure 6b Annually 1 Clean Winch Use a damp cloth and mild soap to clean the frame and labels of dirt and residue Be sure the labels are legible 2 Complete Inspection Perform a complete inspection Refer to section 6 2 3 Record results and keep documentation 3 Factory Service Inspection It is recommended that the winch be serviced by a factory authorized service center or the manufacturer after a period of three years Extreme working conditions may indicate the necessity to increase the frequency Annual servicing shall include but not be limited to an intensive inspection and cleaning of all internal and external components Failure to p
28. evated temperatures Moving machinery Workers or auxiliary equipment can be contacted by or pulled into moving components Sharp edges Workers or the rescue equipment can be injured by or damaged by Do not exceed 350 Ibs 160 kg on the line during sharp edges or components operation Including tool belts etc Electrical hazards Stay away from power lines or components carrying electrical power Overload Do not exceed 350 Ibs 160 kg during operation Establish a regular training program for new and experienced workers 10 Establish a detailed inspection program for your equipment and document the findings Return the equipment to the manufacturer for re work if any problems are found Follow confined space regulations and 11 Plan your work program before starting Have the required standards people equipment and procedures available to do the job 5 1 New Operators or Owners _ M J P rrrr G M The Pelsue PW Series confined space entry retrieval winch is designed to attach to a person entrant and allow them to enter a confined space and assist in exiting if required Every new operator must read understand and follow the instructions in the manual No one should be allowed to use the equipment without training The training should be reviewed with experienced operators on a regular basis At regular intervals perform a detailed inspection of the equip ment and document
29. hether there is a problem Correct the problem before proceeding ANCHORAGE LIFELINE Figure 5h 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 1 9 5 5 Field Operation continued mS AAA c OL Um nz s s 10 Retrieving From Confined Space When exiting from confined space follow this procedure a Turn the winch crank arm clockwise to retract the lifeline and retrieve the entrant from the confined space WARNING Do not use the winch if turning the winch handle counter clockwise retrieves the lifeline The internal brakes are engaged only when the handle operating direction retrieves the lifeline when the handle is turned clockwise b Maintain communications with entrant when preparing to retrieve and during the retrieval process c Support the entrant or load after retrieval and disconnect snap hook 44 CAUTION Should the entrant become caught around a corner or get snagged or tangled it may be necessary to enter the confined space and assist the original entrant This should be considered a new entry or rescue and all regulations apply to the new entrant E g Lifeline Be prepared for a rescue 11 Rescue and Emergencies The winch is designed for entry and retrieval from confined spaces in rescue or emergency applications Although fast response is crucial for saving lives it is still necessary to be aware of and fo
30. ility of personal injury or death Follow the instruction in the safety mes sage Why is this symbol important to you 3 BIG Reasons Accidents Disable and Kill Accidents Cost You Money Accidents Can Be Avoided 4 3 General Safety 1 Read understand and follow the User Manual and all safety signs before using maintaining or inspecting the equip ment 2 Refer to and follow applicable standards and regulations Comply with requirements of local regulations for your applications 3 Establish equipment use training program for inexperienced employees Only trained competent personsshall use the equipment An untrained operator is not qualified to operate the system Have a first aid kit available for use should the need arise and know how to use it Provide a fire extinguisher for use in case of an accident Store in a highly visible place Install and properly secure all guards and shields before operating Now Wear appropriate protective gear This list includes but is not limited to Ahard hat Protective shoes with slip resistant soles Heavy gloves Protective clothing Face Protection 8 Review and follow the Pre Operation Checklist before using a component in the system or system itself 9 Establish a regular maintenance and inspection program with your equipment and maintain detailed records 10 Review safety related items and operating instructions with all personnel
31. ion Keep this manual handy for frequent reference and to pass to new operators Establish a regular training program for experienced and new operators per these instructions Establish a regular maintenance and inspection program to keep the equipment in top condition A WARNING This product is a part of a man rated confined space entry retrieval system The user must read understand and follow the instructions contained in this manual for each component or total system before using this equipment Establish an appropriate training maintenance and inspection program for your people and the equipment Failure to follow these instructions could result in serious injury or death 2 1 Serial Number I IUM aO Always give your dealer the serial number of your Pelsue PW series confined space entry retrieval winch when ordering parts or requesting service or other information The serial number decal is located on the Pawl Cover at the drive handle side of the winch see Figure 2a where indi cated The Serial number decal is embossed with the winch s serial number as well as a Date of Manufacture DOM Please mark the number in the space provided for easy reference The serial number is also permanently stamped into the frame of the winch Do Not Remove the serial number decal or attempt to remove the stamped serial number Winch Model Serial Number Date Of Manufacture DOM Figure 2a PW Series Serial Number Location
32. le may also result affecting the strength of the cable v Remove hitch pin See Figure 5e vi Pull the top of the winch away from the structure and lift the winch up to unhook it from the anchor rod See Figure 5f Store as required Figure 5d Figure 5e Figure 5f 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 1 7 5 5 Field Operation continued E 6 Load Attachment a b c d e Pull on the snap hook with at least 10 Ibs 4 5 kg pull while extending the lifeline until there is sufficient slack to attach to the entrant Use two hands when attaching to the entrant Use one hand to apply a steady pull on the lifeline and to steady the snap hook Use the other hand to depress the lock and open the gate See Figure 5g Insert the entrant D ring into the hook WARNING Always use a full body harness for personnel f g h Close gate and be sure the lock clicks into its locked position Tighten the lifeline Reverse the above procedure when unhooking from the load Figure 5g 7 System Integrity The entrant should always verify the integrity of the attachment and system before entering a confined space To verify the integrity of the system follow this procedure a b o Connect the snap hook to the dorsal ring of the full body harness Snug up the lifeline The entrant should slowly lift their feet off the ground and tran
33. llow all safety and operating procedures Do not take chances with short cuts People s lives are at stake Use only trained competent people who know the equip ment and can safely rescue people from an emergency situation 12 Operating Hints a Follow all applicable OSHA ANSI and local regulations and standards when using this equipment b Train all operators before allowing them to use the equipment Conduct regular refresher training sessions with all experienced operators c Inspect and maintain the equipment on a regular basis Remove defective equipment from service Keep inspec tion and maintenance records d It is recommended that the winch be used in conjunction with other Pelsue components and systems These components and systems have the required function strength and compatibility for all applications Use them per their instructions e Review and follow the limitations for the equipment Do not use in corrosive conditions toxic atmospheres or around mechanical or electrical hazards without taking special precautions f Plan your project before starting to work Anticipate all the normal and unexpected needs relating to equipment and procedures and have them at hand before starting Advance planning can save time and lives g An entrant and attendant are required and must work as a team Maintain communication at all times Page 20 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 20
34. n to the factory for repair Connectors Check the cable collar and clamp for signs of wear distortion or cable fraying Remove from service and return to the factory for repair if any problems are found Check the gate and gate lock on the snap hook Both must open and close easily See Figure 6e If they do not remove from service and return to the factory for service Figure 6e Figure 6c Figure 6d 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 23 6 2 Inspection continued Fui o M M s 6 2 2 FUNCTIONAL INSPECTION A functional check should be performed on the winch every week or more frequently if used extensively The following functional tests should be done 1 Winch Crank Rotation Direction The winch crank must turn in the clockwise direction to retract the lifeline and counter clockwise to extend the lifeline for the internal brakes to engage properly However the lifeline should ONLY extend when there is a load placed on the line With no load present turning the handle counter clockwise should not pay out ANY cable If the winch does return to the factory for inspection 2 Snap Hook Manually check that the swivel on the top of the snap hook turns easily without sticking or binding Also check that the gate lock and the gate open and close easily without binding or sticking If
35. pection Log MODEL NO SERIAL NO MFG DATE BROKEN WIRES AT FITTINGS CABLE MEASURED IN 1 VN i ROKEN CORRO LOCATION DIAMETER LAY OF 1 LAY CORROSION EXCESS WEAR pasa SION LUBRICATION Note Measure location from snap hook Page 30 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 7 0 Storage Prior to storage the winch should be thoroughly inspected and maintained Repair or replace any worn or damaged components to prevent any unnecessary down time at the next use Follow this procedure 1 Thoroughly clean the winch using a mild soap on the frame and labels be sure all of the labels are legible 2 Use a neutralizing solution to clean lifeline This is particularly important if the unit has been used in corrosive or toxic environments Perform a complete inspection of the winch and document the results prior to storage Lubricate the winch according to the requirements in this manual Touch up all nicks and scratches in order to prevent corrosion O Store the winch in a cool dry place 8 0 Contact Information For More Information PELSUE T A Pelsue Company 2500 S Tejon St Englewood CO 80110 Toll Free 1 800 525 8460 Telephone 1 303 936 7432 Fax 1 303 934 5581 Website www pelsue com Email sales pelsue com 500138 00
36. period service must be pre approved by the T A Pelsue Company and service must be performed by the T A Pelsue Parts and Service Department in Englewood Colorado or at the option of the T A Pelsue Company service may be performed at any designated service center which may include any authorized service center for the compo nent manufacturer Unauthorized repairs will not be covered by this warranty Damage or failure due to misuse mishandling or unauthorized modifications will not be covered by this warranty Unless otherwise agreed the T A Pelsue Company shall repair or replace the defective components within 30 calendar days of notice of failure T A Pelsue Company s obligation hereunder shall be limited to the repair or replacement of the product or component as set forth above and shall not include any liability whatsoever for dam ages caused by such failure including but not limited to consequential or incidental damages flowing from use or lack of use of product Any replacement repair modification installation or other service performed by the T A Pelsue Company shall be warranted by the remainder of the unexpired period of the warranty or for a period of 90 calendar days which ever is longer All materials or parts returned for credit or warranty shall be returned only with prior approval and will be subject to factory inspection before credit is allowed Parts claimed defective will be replaced upon request and will
37. plications a back up fall arrest may be required In these applications a swing angle of less than 30 degrees is recommended Use only an approved mounting or anchoring system at all times Use only approved connectors that are equipped with an anti rollout device 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 1 3 5 3 Applications continued a r sv 4 Emergency Rescue In emergency situations use the winch to remove personnel from a hazardous or an unsafe environment In these situ ations a back up fall arrest system is generally not required Be sure to use the proper mounting and anchoring system for the winch Use only an approved harness for personnel Always be aware of the system limitations and follow the instructions 5 Limitations Operators must be aware of several limitations on the use of the winch whenever it is used and plan their work accord ingly Limitations include but are not limited to a Corrosion Do not keep the winch in an area that has a corrosive atmosphere Corrosive vapors can be released by sewage plants or in fertilizer plants Sea water or spray can also cause corrosion to the case lifeline or other components Long term exposure to these types of environments will require more frequent inspections to ensure that the function of the unit has not been affected b Chemical or Toxic Environments Work environments that contain strong acids bases or other cor
38. roduct Warranty y E Tm Introduction amp Product Information 7 ui Serial Number cr e Configuration amp Assembly 8 BU e ma lj f 9 a NERONE Warning Statement qucm e Safety Alert Symbol 7 General Safety Operating Safety LA P Maintenance amp Inspection Safety OD iss ens ee erie ODE AU Re 12 earn s New Owner or Operator P c C sua Pre Operation Inspection uoa s Applications or o System Requirements or E s Field Operation e rere Maintenance amp Inspection 21 O Maintenance Du ridens Inspection ro TC X Winch Inspection Log Drs Winch Cable Inspection Log rH A 31 sa ss Contact Information 31 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 1 0 General Information 1 1 Quality Policy T A Pelsue Company Quality Policy OUR GOAL IS THE PURSUIT OF NEVER ENDING IMPROVEMENT IN PRODUCT QUALITY AND BUSINESS SYSTEMS METHODS TO BE EMPLOYED IN ATTAINING THIS GOAL WILL INCLUDE NEW PRODUCT QUALITY PLANNING EMPLOYEE TRAINING AND UTILIZATION OF EMPLOYEE INVOLVEMENT GROUPS TO SOLVE PROBLEMS IN AN INCREASINGLY COMPETITIVE MARKETPLACE
39. rosive chemicals in solutions sprays or vapors may damage the winch or auxiliary components Inspect the unit frequently to detect any damage or change in functionality of the unit Chemical damage may be difficult to detect visually and periodic lifeline replacement is recommended to insure safety c Electrical Hazards Stay away from power lines or other components carrying electrical power The metal lifeline can conduct electric ity if it gets close to or contacts a power line or electrified component Remember electricity can jump across an air gap and electrocute personnel using the winch Contact your local utility to remove or disconnect the power before working around these components Contact Pelsue for synthetic rope options to reduce conductivity d Load Capacity Do not exceed the winch capacity of 350 Ibs or 160 kg includes people harness tools etc Do not carry more than one person at a time on the lifeline Overloading the winch can exceed the design safety factors and could create hazards d Training Do not allow anyone to use this winch unless they are trained in its limitations and use Untrained operators can expose themselves and others to hazards Train new operators before using the unit Review operating procedures on a regular basis with experienced personnel 5 4 System Requirements E The Pelsue PW series man rated winches are a component in a confined space entry retrieval system The winch and all auxili
40. rovide proper service may shorten product life and could endanger performance or function Page 22 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 6 2 Inspection R 6 2 1 VISUAL INSPECTION A complete visual inspection should be performed on the winch prior to using The following items should be checked 1 Labels Check that all the labels are clean and legible The PW series winch has 3 labels and a serial number plate see Figures 6c and 6d Clean the labels if any are dirty using mild soap and a damp cloth Replace if any are illegible Refer to section 2 1 and 3 0 for specific locations of serial number plate and labels Fasteners Check that all screws and other fasteners are tight Tighten if any are loose Replace if any are missing Frame Check the frame and housing for cracks dents bends or breaks If there are major dents or any other structural damage the unit should be removed from service and returned to the factory for repair Crank Arm Check that each handle on the crank arm is tight If the crank arm is bent or damaged remove winch from serv ice Do not use winch unless crank arm is fully functional Corrosion Check all components for damage from corrosion Although all components resist corrosion working in corrosive environments can lead to damage Inspect the mounting surfaces and fasteners for signs of damage If damage is found remove from service and retur
41. rs or caught between two heavy objects See Fig 21 Remove from service and return to the factory for re work vii Unlaying and Bird Caging Check for unlaying and bird caging of strands This condition appears as the formation of gaps loops and excessive clearance between strands See Fig 22 If this appears remove the unit from service and return to the factory for re work viii Kinks and Bends Check for kinks and bends in the cable See Fig 23 Kinks and bends are created when a loop forms in a slack cable and then it is pulled tight without the loop uncoiling Remove from service if kinks or bends are formed in the cable and return to the factory for repair ix Heat Damage Torch Burns or Electric Arcs Check for examples of heat damage torch burns or electric arc strikes Localized discoloration fusing or melting indicate this type of damage If this is found remove the unit from service and return to the factory for repair CRUSHED CABLE Figure 6k Figure 6m a a e SSS SSS WS gt lt Sos SSS Qs BIRD CAGING Figure 6 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 27 6 2 Inspection continued c Synthetic Rope Inspection The rope must be inspected over its full length and the results recorded in the inspection log Always wear heavy gloves to prevent cuts or slivers while handling the cable If any cut
42. s or frays are present remove from serv ice i Tears or Cuts The synthetic rope consists of an outer jacket and an inner core Carefully inspect area around cable crimps for tears or cuts in outer jacket If the inner core is exposed at all the winch must be removed from service for cable replacement ii Worn or Abraded Outer Jacket If the outer jacket shows signs of abrasion usually resulting in a fuzzy appearance the rope must be replaced A few threads pulled out of the outer jacket may be clipped off with a pair of scissors so long as this action does not expose the inner core iii Bulges or Reduction in Diameter Check for bulges or reduction in diameter in the synthetic rope These indicate a serious condition present in the rope Remove from service if bulges or reductions are present Corrosion Check for corrosion Corrosion can be seen as a discoloration of the outer jacket however this outer jacket could hide corrosion of the inner core The rope is safe for exposure to water however exposure to other chemical environments may affect the strength of the rope Check with the factory PRIOR to the rope being exposed to such conditions to determine the affect on the rope If the rope is exposed to an unknown chemical agent the winch should be returned to the factory so that the rope may be replaced iv v Knots Knots forming in the synthetic rope are a source of weakness in the rope The rope should NEVER
43. sfer the weight to the lifeline Be sure the winch holds you in a stationary position Be sure the full body harness is comfortable and does not pinch chafe or bind Adjust per manufacturer s instruc tions before starting Do not enter confined space unless connectors brakes winch and harness are functioning properly A WARNING DO NOT TEST OVER CONFINED ENTRY Page 1 8 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 5 5 Field Operation continued lt lt eee 8 Crew Personnel A working crew requires the use of at least two 2 people at all times The entrant who is attached to the end of the lifeline and the attendant who turns the winch crank and guides the lifeline Each must be properly trained in the use of the equipment for their task As the entrant enters the confined space the entrant should maintain communication with the attendant operating the winch Heavy gloves should be worn by the attendant when guiding the cable The two people must work as a team to get the job done safely and efficiently 9 Entering Confined Space When entering confined space follow this procedure a The entrant should move slowly and smoothly into the confined space either vertical or horizontal b The attendant should turn the winch handle counter clockwise to pay out the lifeline W
44. sure that the gate will not open unless the lock is released The snap should also be free from rust as this is a sign of weakness 5 Ifthe winch is not in good condition remove from service and tag for shipment to an authorized repair depot or the factory for re work Using a winch that is not in good condition can lead to a hazardous condition for entrant s 6 Go through the detailed inspection procedure on a regular basis at least annually per the Inspection Sectionofthis manual Document the results using the sample form and retain for your files 7 Adetailed inspection is required after each duty cycle 5 3 Applications 2 2 2 2 2 22 2 1 General The Pelsue PW series man rated winches are designed to be used in work support or rescue applications It extends and retracts a line as the handle is turned When the handle is turned an internal brake holds the drum and the line will not extend or retract 2 Scope The winch works well in both vertical and horizontal applications However different mounting anchoring and support systems are required for each type of application The user has the responsibility of reading and following the instructions for the other systems in addition to the winch Misuse or abuse of any component can create hazards for personnel 3 Work Support The winch works well for supporting workers in a boatswains chair or a full body harness single point suspension In some ap
45. the results Remove from service if deficiencies are found Alterations or misuse of this equipment or failure to follow instructions may result in serious injury or death It is the responsibility of the owner s organization or operator to read this manual and to train all other operators before they start working with the equipment Follow all safety instructions exactly Safety is everyone s business By following recommended procedures a safe working environment is provided for the operator bystanders and the area around the work site Untrained operators are not qualified to operate the equipment Many features incorporated into this equipment are the result of suggestions made by customers like you Read this manual carefully to learn how to operate the equipment safely and how to set it to perform as intended By following the operating instructions in conjunction with a good maintenance program your winch will provide many years of trouble free service 500138 001 Product Manual PW Series Man Rated Winch Revision 05 Date 10 08 2008 Page 12 5 2 Pre Operation Inspection nmm M M MH 1 It is necessary to perform a detailed visual inspection prior to using the winch If deficiencies are found remove the winch from service and return to Pelsue for re work This checklist should be used as a guide to determine whether the equipment is in good operating con
Download Pdf Manuals
Related Search