manual de utilizare / user`s manual motocoasa / brush cutter bc 2200
Contents
1. Be aware not to hit or cut the fuel tank while you put it to the ground Do not let the brush cutters fall down to the floor it may damage the machine Whenever the machine is not used for over 1 month proceed as follows e Empty completely the fuel tank from the mixture Protect all engine metal parts from corrosion by provided those with a thin coat of oil Remove the spark plug put some drops of oil in the cylinder then pull the recoil starter 2 to 3 times in order to distribute evenly the oil put back the spark plug e We recommend you to start the engine during a few minutes every 60 days of inactivity Shake accurately the mixture in the fuel tank before any use in order to re mix the oil with the gasoline Technical data Engine capacity 52cmc Fuel tank capacity 1200ml Max power 2 2CP Blade diameter 255mm Maximum blade rotation speed 9000 rot min Net weight without fuel and accessories ght 7 2kg Sound level LwA 108dB A Vibration level 7 5 m s2 12 Thoroughly clean the whole machine and its accessories Store it out of the reach of children in a stable and secure position in a cool and dry place avoid too high and too low temperatures Protect it from exposure to direct sunlight Keep it in the dark if possible Don t keep it in plastic bags to avoid humidity build up Warranty This warranty covers all material or production flaws excluding Batteries chargers defective parts subject to norm2. Do not operate the brush cutter in case of bad weather wind rain snow ice Your power tool should be serviced by a qualified specialist using only standard spare parts This will ensure that it meets the required safety standards Application The brush cutter is intended for personal use for cutting grass bush arborescent shrub clumps wheat and similar plants IT IS NOT DESIGNED FOR PROFFESIONAL USE 1 Mixture tank 2 Gas control with stop button engine 3 Carburetor air filter 4 Handle bar 5 Anti vibration support 6 Gas control lever 7 Transmission axle 8 Gear box 9 Cutting tool 10 Safety guard Accessories 1 Nylon head 2 Three teeth blade 3 Harvester head 4 Harness 5 Fuel mixture bottle Assembly Handle assembly Fit the handle 4 on the transmission shaft 7 with the throttle lever on the right side and tighten the 2 screws Mounting safety guard This safety guard must be fastened on the Support near the gear case with the four screws and the two plates 1 Use of the nylon head safety guard must be used with its two parts mounted main part of different colors small black blade holder 2 Use of the 3 teeth blade must dismount tile small black blade holder with a screwdriver and use only the main part of the safety guard Harness The harness provided is a model with foam and hip protection lt must be used with belt on the left shoulder and the hip protection on the right side Balance
3. build Ae ELL MANUAL DE UTILIZARE USER S MANUAL MOTOCOASA BRUSH CUTTER BC 2200 RC II Va multumim pentru achizitionarea acestui produs BuildXell fabricat conform celor mai inalte standarde de siguranta si de functionare si instructiunile generale de siguranta inaintea utilizarii echipamentului Nerespectarea acestor reguli poate avea ca rezultat producerea incendiilor si sau a ranirilor personale 2 Avertizare Pentru siguranta dumneavoastra cititi cu atentie acest manual Masuri de siguranta generale Zona de lucru e Pastrati zona de lucru curata si bine iluminata Umiditatea si zonele intunecate pot crea accidente e Nu lasati copii sau persoanele neautorizate in zona de lucru Distragerea atentiei poate cauza pierderea controlului uneltei e Nu suprasolicitati unealta Masina poate fi folosita in conditii de siguranta daca sunt respectati parametrii de exploatare care o caracterizeaza Nu utilizati unelte cu un alt scop fata de cel pentru care sunt destinate Masuri de siguranta personala e Nu utiliza i motoferastraul daca ati consumat b uturi alcoolice medicamente care pot influenta capacitatea de reactie si concentrare droguri sau alte substante halucinogene sau daca sunteti obositi bolnavi sau suparati e Particulele de iarb si arbusti rezultate in urma taierii pot cauza reac ii alergice e Intotdeauna utilizati o imbracaminte adecvata Nu purtati haine largi sau bijuterii Daca aveti parul lung
4. n iarba In cazul in care loviti din greseala un obiect de dimensiuni mai mari sau se blocheaza capul de taiere din cauza suprasolicitarii sau a materialului vegetal fibros nf urat n instrumentul de t iere trebuie s reduceti turatia pana la turatia de mers n gol i s decuplati ambreiajul Asigurati va c masina este oprita prin ap sarea butonului pornit oprit de pe maner in pozitia O Verifica i dac dispozitivul de taiere nu a fost deteriorat cum ar fi ruperea din ilor sau lamelor situatie in care inlocuiti l imediat In cazul n care pe capul de taiere este doar infasurat material vegetal eliminati l cu ajutorul unei perechi de m nu i 5 Capul de t iere transmite vibratii catre utilizator n timpul utilizarii chiar daca masina este dotata cu un dispozitiv anti vibratii ceea ce poate genera o cre tere a gradului de oboseala Din acest motiv v recomand m s lua i pauze regulate timp in care lasati motorul sa functioneze la ralanti pentru a se raci cu ajutorul curentului de aer generat de volanta Curatare si intretinere Echipamentul nostru a fost proiectat astfel incat sa poata fi utilizat pentru o perioada indelungata cu un minimum de intretinere Veti putea obtine intotdeauna o satisfactie maxima in timpul utilizarii respectand indicatiile de mai jos Curatare Pastrati curate fantele de ventilatie ale carcasei pentru a preveni supraincalzirea motorului e Regulat de preferat dupa fiecare utilizare
5. i cu motocoasa n caz de vreme nefavorabil v nt ploaie z pad gheata pericol crescut de accidente 2 Repararea trebuie realizata numai de catre personal autorizat prin inlocuirea cu accesorii si piese de schimb originale pentru a se evita producerea accidentelor datorate reparatiilor necorespunzatoare Service Repararea trebuie realizata numai de catre personal autorizat prin inlocuirea cu accesorii si piese de schimb originale pentru a se evita producerea accidentelor datorate reparatiilor necorespunzatoare Domeniu de utilizaref Motocoasa este destinata uzului personal pentru operatiile t iere a ierbii arbustilor tufelor si a cerealelor paioase grau orz etc NU ESTE PROIECTATA PENTRU UZ INDUSTRIAL Parti componente 1 Rezervor pentru amestec combustibil Buton stop motor Carburator filtru aer Maner Suport anti vibratii Levier acceleratie Ax transmisie Cutie viteze Accesoriu taiere 0 Aparatoare siguranta Accesorii incluse in pachet 1 Cap taiere cu nylon 2 Cutit cu 3 lame 3 Cutit cu 80 dinti 4 Ham protectie 5 Recipient amestec carburant 0 St oe aN Pregatirea pentru punerea in functiune Asamblare maner Montati manerul 4 pe axul transmisiei 7 cu levierul de acceleratie pe partea dreapta si strangeti cele 2 suruburi de fixare Asamblare aparatoare siguranta Aceasta aparatoare trebuie fixata cu patru suruburi pe axul transmisiei langa cutia de viteze 1 Utilizar
6. Avoid accidental starts Carrying power tools with your finger on the switch makes accidents more likely Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from the power tool Loose clothes jewellery or long hair can become entangled in the moving parts Service Your equipment should be serviced by a qualified specialist using only standard spare parts This will ensure that it meets the required safety standards Specific safety instructions for brush cutter AN Special precautions are required when using brush cutter due to high speed of the cutting head e The commissioning of the machine it require the vendor or the person skilled explanations for the safe operation of the equipment e Never start and or use the machine in a close area or inside a structure as there is some risk of intoxication due to exhaust gas Mix and handle the fuel in the open air only far away from potentially explosive surroundings for example in the presence of inflammable liquids gases or dust e Refrain from smoking while handling or mixing the fuel e All people animals and delicate property must be kept at least 15 meters away from the machine and the area of working This machine is intended for use only by persons age over 16 who were trained by authorized persons e The equipment will be loaned only to persons who have been trained on its use and will be always accompanied by User Manual
7. curatati echipamentul cu o carpa moale Daca murdaria persista utilizati o carpa umezita intr o solutie de apa si sapun e NU utilizati solventi ca de exemplu petrol si derivati alcool intrucat acestia pot deteriora partile din plastic Intretinere cutie de viteze Dupa fiecare 25 de ore de functionare ungeti cutia de viteze Desurubati capacul lateral al cutiei de viteze i adaugati un lubrifiant special cutie de viteze care rezista la temperaturi inalte utilizand un instrument potrivit Strangeti bine capacul ntre inere dup utilizare La incheierea lucrului curatati complet motocoasa de iarb sau murd rie asigurati va c nu exist nici un material infasurat n instrumentele de t iere si puneti ma ina napoi n ambalajul ei pentru a evita accidentari sau deteriorari Nu loviti sau t iati rezervorul de combustibil n timp ce il asezati in pozitia de stationare Ori de c te ori aparatul nu este folosit pentru mai mult de o luna procedati dupa cum urmeaz e Goli i complet rezervorul de amestecul carburant e Protejati contra coroziunii toate piesele metalice motor cu un strat sub ire de ulei e Scoate i bujia puneti c teva pic turi de ulei n cilindru apoi trage i de manerul demarorului de 2 3 ori n scopul de a distribui uniform uleiul dupa care montati inapoi bujia e Va recomandam sa porniti motorul timp de cateva minute la fiecare 60 de zile de inactivitate Inainte de orice utilizare ag
8. acesta trebuie legat Apare riscul prinderii acestora de catre partile componente ale masinii aflate in miscare e Utilizati intotdeauna casti antifonice ochelari si manusi de protectie e Evitati pornirile accidentale Transportarea uneltelor cu degetul pe intrerupator creste riscul de accidentare Masuri de siguranta specifice motocoasel ATENTIE Se impun masuri speciale de siguranta in cazul utilizarii motocoaseii datorita vitezei mare de rotire a capului de taiere La prima punere n func iune a utilajului se solicit v nz torului sau persoanelor de specialitate explica ii cu privire la func ionarea n condi ii de siguran a echipamentului e Nu porniti si sau utilizati aparatul in spatii inchise intrucat exista riscul intoxicatiei cu gazele evacuate Amestecul de ulei si combustibil trebuie realizat n aer liber departe de zonele cu potential exploziv de exemplu in prezenta lichidelor gazelor sau particulelor inflamabile e Este interzis fumatul in timpul alimentarii cu combustibil e Trebuie p strata o distanta de cel putin 15 de metri intre ma in i oameni animale sau bunuri fragile e Este interzisa utilizarea utilajului de catre persoane minore cu exceptia tinerilor peste 16 ani care au fost instruiti de catre persoane autorizate Utilajul va fi mprumutat numai persoanelor care au fost instruite cu privire la utilizarea acestuia i va fi nso it ntotdeauna de Manualul de utilizare e Nu lucra
9. al wear amp tear such as bearings brushes cables and plugs or accessories such as drills drill bits saw blades etc Damage or defects resulting from maltreatment accidents or alterations nor the cost transportation We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool Definitely excluded from the warranty is damage resulting from fluid permeation excessive dust penetration intentional damage on purpose or by gross carelessness inappropriate usage use for purposes for which the device is not suitable incompetent usage e g not following the instructions given in the manual inexpert assembly lightning strike erroneus net voltage This list is not exhaustive 13
10. e cap taiere nylon aparatoarea trebuie utilizata cu ambele parti componente rosie si neagra 2 Utilizare cutit cu 3 lame desprindeti cu o surubelnita componenta de culoare si utilizati doar partea principala Ham protectie Hamul furnizat este un model cu spum i protec ie a soldului Se utilizeaza cu centura pe um rul st ng i protec ia old pe partea dreapia Echilibrarea echipamentului Inainte de orice utilizare trebuie echilibrat echipamentul prin ajustarea hamului dup cum urmeaz e Puneti centura pe um rul st ng i atasati c rligul la echipament 3 e Reglati pozi ia pe axul transmisiei n scopul de a ob ine un bun echilibru ntre motor si sistemul de taiere Montare cap de taiere cu nylon Introduce i o surubelnita n locasul de blocare 2 orificii pozitionate pe protec ia din o el si n bucsa axului transmisiei desurubati piulita in sensul acelor de ceasornic utiliz nd cheia furnizata i indepartati capacul metalic lasand doar saiba plata Insurubati capul de taiere cu nylon Verificati blocarea completa a capului nylon dupa care indepartati surubelnita din locasul de blocare Montare cutit cu 3 lame Introduce i o surubelnita n locasul de blocare 2 orificii pozitionate pe protec ia din o el si n bucsa axului transmisiei desurubati piulita in sensul acelor de ceasornic utiliz nd cheia furnizata i indepartati capacul metalic si saiba plata Pozitionati cutitul de taie
11. itati amestecul carburant n rezervor n scopul de a l reomogeniza Date tehnice Capacitate cilindrica 52cmc Capacitate rezervor combustibil 1200ml Putere maxima 2 2CP Diametrul maxim de taiere 255mm Turatie maxima 9000 rot min Greutate fara accesorii si combustibil 7 2kg Nivel de zgomot LwA 108dB A Nivel de vibratii 7 5 m s2 Intotdeauna inainte de depozitare curatati carcasa cu o carpa putin umezita in apa cu sapun Depozitati unealta intr un spatiu inaccesibil copiilor intr o pozitie stabila si sigura intr un loc racoros si uscat evitand temperaturile prea ridicate sau scazute Protejati unealta fata de actiunea directa a razelor solare si pastrati o intr un loc intunecos daca este posibil Nu pastrati unealta ambalata in folie sau in punga de plastic pentru a evita acumularea umiditatii Garantia acopera toate materialele componente si viciile de fabricatie cu exceptia fara insa a fi limitate la Baterii incarcatoare componente uzate ca urmare a unei exploatari normale perii colectoare rulmenti cabluri etc sau accesorii burghie biti dalti etc Defecte cauzate de o exploatare intretinere si depozitare necorespunzatoare modificari neautorizate asupra echipamentului costul transportului Pagube materiale si leziuni corporale rezultate in urma exploatarii necorespunzatoare a echipamentului Deteriorari cauzate de lichide patrundere excesiva de praf distrugere intentionata utilizare inadecvata pentru scopu
12. modificarilor condi iilor de lucru utilizarii pentru o perioada indelungata sau varia iei de temperatura sau presiune a mediului ambiant Pentru reglare urmati istructiunile de mai jos e n uruba iin sensul acelor de ceasornic urubul galben p n c nd ajunge la baza fara a l forta e Din aceasta pozi ie desurubati 1 5 rotatii Porniti motorul si accelerati l la maxim e G si i punctul n care motorul este la regim maxim de tura ie prin n urubarea sau desurubarea a cate aproximativ 1 8 dintr o rotatie completa e Cand ati stabilit regim maxim de turatie desurubati un sfert de rotatie surubul in scopul de a spori amestecul de benzina Reglare ralanti Pentru un reglaj corect aceasta operatie trebuie sa se faca in timp ce motorul este cald e n uruba i sau desurubati urubul fluture p n c nd motorul are o turatie de aproximativ 2500 rpm e Acest reglaj necesita un instrument de control special Dac nu il aveti contacta i un service autorizat Taiere iarba Pentru o taiere corecta pendulati masina stanga dreapa pe o latime de de 1 5 metri Asigurati va ca la fiecare pas va pastrati starea de echilibru Daca utilizati cutitul cu 3 lame pentru iarba incercati sa taiati de la dreapta la stanga pentru colectarea ulterioara a ierbii pe partea stanga Dac este posibil evitati pietrele si bucatile de lemn chiar de mici dimensiuni bulgari de p m nt sau orice alt obiect care ar putea fi ascuns sau putin vizibil
13. ock and start to use the machine If the engine do not start may be the spark plug is wet in this event unscrew the spark plug wipe and dry it and pull the recoil starter several times without the spark plug in place in order to clean and ventilated the combustion chamber Grinding During the first ten hours of work run the engine at a moderate rom we advise you in any case do not use your engine at high speed as the different components must adjust one with the others during grinding At the end of the grinding the engine will reach its maximum power After the two first hours of work make a pause and check that all nuts and screws are securely fastened tighten if necessary Carburetor adjustment During a normal use the carburetor may have some slight changes especially when there are some changes of working conditions and after many hours of work or because of variation of temperatures or pressures in the surrounding If the carburetor needs adjustment proceed as follows e Screw clockwise the yellow screw of the carburetor until it comes to the base never force it From this position unscrew it by one and a half turn e Start the engine and accelerate at the maximum Find the point where the engine is at the maximum rpm by screwing or unscrewing at around 1 8 of turn at each time e When you have founded the maximum rpm unscrew of one 1 4 of turn the screw in order to increase the mixture gasoline Idle speed adju
14. of the machine Before any use you must adjust the harness in order to balance the machine as follows e Place the belt on your left shoulder and hook to the machine 9 e Adjust the position of the fixation on the tube of the machine in order to obtain a good balance between the engine and the cutting system Mounting nylon head Insert a screwdriver into the slot lock 2 holes positioned on steel protection sleeve and shaft drive unscrew the nut in a clockwise direction using the supplied wrench and remove the metal cover leaving only flat washer Screw the nylon cutting head Check complete blocking of nylon head then remove the screwdriver from locking seat Mounting three teeth blade Insert a screwdriver into the slot lock 2 holes positioned on steel protection sleeve and shaft drive unscrew the nut in a clockwise direction using the supplied wrench and remove the metal cover and flat washer Position knife cutting into its place in transmission shaft put flat washer and metalic cover Fasten the nut counter clockwise direction then remove the screwdriver Make sure that all different parts of the cutting tool are securely fastened as above Mounting harvester head Base Protector plate Screw M5X10 Gear box Base plate assy Flat pad 5x12x1 5 Screw M5x 14 OMONDOORWDY Up clamp 80T Blade i gt 10 Down clamp pi e 11 Scraper seal s li PE Sc a 12 Nut M10x1 25 Eo ol Mo 13 Collection b
15. on Even the machine is equipped with an anti vibrating device the vibration can generate an increased tiredness For this reason we recommend taking regular pauses during work We recommend as well that after a few hours of work to take a pause a few minutes and leave the engine at idle rom in order to cool down by the air current created by the flywheel Cleaning and maintenance Our machines have been designed to operate over a long period of time with a minimum of maintenance Continuous satisfactory operation depends upon proper machine care and regular cleaning Cleaning e Keep the ventilation slots of the machine clean to prevent overheating of the engine e Regularly clean the machine housing with a soft cloth preferably after each use If the dirt does not come off use a soft cloth moistened with soapy water e Never use solvents such as petrol alcohol ammonia water etc These solvents may damage the plastic parts Maintenance of gearbox Every 25 hours grease the gear box Unscrew the lateral tap of the gear box and put grease inside using an appropriate tool Use a special gear box grease that resist to high temperature Screw the tap tightly Maintenance after use When you finish working clean completely the brush cutter from any grass or dirt make sure there is no grass material wrapped in the cutting tools and put the machine back in its packing in order to avoid to injury yourself or other people during the transport
16. ox n ua 14 Screw M4x8 Operation ne 4 WARNING Never use steel wires or other materials for cutting gt Fuel mixture Use a fuel mixture of 4 4 sintetic oil 96 gasoline Euro 95 You must use the mixture during the three weeks that follows its preparation Shake accurately the mixture in the fuel tank before any use in order to re mix the oil with the gasoline This operation should be done in an open area away from any flames or sparks while the engine is turn off Do not smoke and do not use the telephone during operation Engine start 1 Push the start button on the right handle in position 2 Pull and block the gas lever on the right handle 10 3 Press on the lt lt primer gt gt under the carburetor 4 or 5 times to allow the gasoline to arrive on the return fuel tank transparent gasoline pipe 4 Push the starter lever of the carburetor in position ON 5 With your left hand grip the brush cutter and press the transmission shaft in order to keep firmly positioned the machine on the ground and with the right hand pull slowly the handle recoil starter until the pawls hook onto the flywheel 6 Pull hardly 4 or 5 times the handle recoil starter until the starting Never pull the recoil starter to its all length in order to avoid damages to the recoil starter 7 Release the starter level 1 2 halfway back for approx 10 20 sec and after that fully release to OFF position 8 Pull the gas lever to unbl
17. re in locasul din bucsa axului transmisiei peste care asezati saiba plata si capacul metalic Strangeti piulita in sens invers acelor de ceasornic dupa care indepartati surubelnita Montare cutit cu 80 dinti 1 Soclu 2 Placa de protectie 3 Surub M5X10 4 Cutie de viteze 5 Ansamblu soclu ore 6 7 8 9 Placa 5x12x1 5 1 A i LZ Clema superioara SU SEI AES Lama cu 80 dinti a zi N 10 Clema inferioara i i 11 Bucsa etansare eg 12 Piulita M10x1 25 Se tn Paine ee 13 Caseta de colectare 3 o Y i 14 Surub M4x8 Pena Oe Utilizare T iee Dia AN ATENTIE Este interzisa utilizarea firelor metalice sau a altor materiale pentru taiere Preparare amestec carburant Utilizati un amestec de 4 4 ulei sintetic 96 benzina cu cifra octanica minim 95 Amestecul trebuie utilizat in maxim 3 saptamani de la preparare Agitati rezervorul de combustibil nainte de orice utilizare n scopul de a omogeniza amestecul ulei benzina Aceast opera ie trebuie executat ntr o zon deschis departe de orice flac r sau scanteil n timp ce motorul este oprit Nu fumati si nu folosi i telefonul n tot acest timp Pornire motor 1 Apasati butonul pornit oprit de pe m nerul dreapta n pozi ia 2 Apasati i blocati maneta de acceleratie de pe m nerul dreapta 3 Ap sa i pompa de amorsare buton transparent de sub carburator de 4 5 ori pentru a permite benzina sa se intoarca in rezervorul de combustibil prin cond
18. ri in care acest echipament nu este proiectat etc HONEST GENERAL TRADING SRL isi rezerv dreptul de modificare a programului de livrare n ceea ce prive te forma tehnologia i echiparea Prin urmare nu pot fi ridicate preten ii cu privire la informa iile i figurile din acest manual de utilizare N Thank you for buying this BuildXell product manufactured according to the highest safety and performance standards Instructions carefully before using the appliance Your power tool should only be given to other users together with these instructions gt WARNING For your own safety read this manual and the general safety G eneral power tools safety warnings Working area e Keep working area clean and well lit Untidy and dark areas can lead to accidents e Keep children and bystanders at a distance when operating a power tool Distractions can cause you to lose control of it e Do not overload the machine The machine can be used safely if complied with the relevant operating parameters Do not use tools with a different purpose than the one for which they are intended Personal safety e Do not use the tool if are unde influence of alcoholic beverages drugs that may affect the ability to concentrate and react hallucinogenic drugs or other substances or if you are tired sick or upset e Always use earmuffs goggles and gloves e Chopped grass and shrubs sprayed into the air can cause allergy reactions e
19. stment For a correct adjustment this operation must be done while the engine is hot e Screw or unscrew the butterfly screw until the engine is at around 2500 rpm e Those adjustments require a special tool control If you do not have it contact an approved after sale service Grass Cutting Cut the grass like if you were in a corridor of 1 5 meters wide move step by step balancing the machine right and left and vice versa Make sure at each step that you are still well balance on your feet If you are using the 3 teeth blade for the grass always cut your right to left and leave a pile of cut grass on the left for later gathering If possible avoid stones even small ones piles of earth small piece of wood or anything that could be hidden or poorly visible in the grass If you hit a large object by accident or if you block the cutting tool due to overloading or overload of grass or stringy vegetal material wrapped in the cutting tool you must reduce the speed to the idle speed and disengage the clutch Make sure that the cutting tool is stopped by pushing tile stop button Put the brush cutter on the ground and check that the cutting tool has not been damaged such as breakage of teeth for the blade cracking If necessary change the cutting tool If the tool is only wrapped by vegetal material with your pair of gloves remove the vegetal materials and clean the cutting tool 11 Brush cutter transmit vibrations to the user during operati
20. ucta de retur 4 Deplasati clapeta de soc n pozi ia ON 4 5 Cu mana stanga prindeti masina si apasati arborele de transmisie in scopul de a mentine ferm pozitionat aparatul pe sol iar cu mana dreapta trageti incet de manerul demarorului pana cand clichetii agata volantul 6 Trageti cu putere de 4 5 ori manerul demarorului pana porneste motorul Nu trageti niciodata de maner pana la desfasurarea totala a cablului pentru a evita deteriorarea demarorului 7 Eliberati clapeta de soc pana la 1 2 din cursa ei si mentineti o in aceasta pozitie timp de aproximativ 10 20 secunde dup care apasati o pana in pozitia OFF 8 Apasati pentru deblocare maneta de acceleratie si incepeti s utilizati ma ina Dac motorul nu porne te este posibil ca bujia sa fie umeda In acest caz desurubati bujia stergeti o si uscati o dupa care actionati demarorul de mai multe ori f r bujia montata n scopul de a cur a i ventila camera de ardere Rodaj n primele zece ore de functionare utilizati o turatie moderata pentru functionarea motorului In orice caz nu supra turati motorul pentru a permite componentelor in miscare un rodaj corect Dupa incheierea perioadei de rodaj motorul va atinge performantele maxime Dup primele dou ore de functionare verifica i strangerea corecta a tuturor piulitelor si uruburilor Reglare carburator In timpul functionarii normale carburatorul poate avea unele mici dereglari n special din cauza
Download Pdf Manuals
Related Search