FEMA ELECTRÓNICA
Contents
1. in the same conduit with power lines heaters solenoids SCR controls etc and always far from these elements When shielded wires are used leave unconnected the shield on the transmitter side and connect the other end of the shield to the ground terminal of the machine EXCITATION VOLTAGE Model ISC P incorporates an internal power supply for transducers The output of this power supply is connected to terminals 7 and 9 Do not connect these terminals to an external power supply beacuse both units will be permantently damaged FEMA ELECTR NICA Page 10 SAFETY CONSIDERATIONS PRESCRIPTION Before starting any operation for replacement maintenance or repair the unit must be AA disconnected from any kind of power supply Keep the unit clean to assure good functioning and performance To prevent electrical or fire hazard do not expose the unit to excessive moisture Do not operate the unit in the presence of flammable gases or fumes such an environment definetely constitutes a safety hazard The unit is designed to be mounted on a metal panel 11 WARRANTY FEMA ELECTR NICA S A warrants this unit to be free of manufacturing defects for a period of 24 MONTHS from shipment date This warranty covers both materials and manufacturing processes This warranty is VOID ifthe unit shows evidence of damages as a result of misapplication accident misuse or if the product had been tampered or repaired by2. paid of the product upon which liability is based In no event shall FEMA ELECTRONICA S A be liable for consequential inicidental or special damages FEMA ELECTR NICA Page 11 other products 4 Programmable Signal Converters amp Large Displays Panel Meters Isolated Transmitters Standard Miniature Large Displays Panel Meters Panel Meters for TIME www fema es ELECTRONIC INSTRUMENTATION FOR INDUSTRY FEMA ELECTRONICA S A Pol Ind Santiga Altimira 14 T14 N2 E 08210 Barber BARCELONA ESPA A SPAIN Tel 34 93 729 6004 www fema es Fax 34 93 729 6003 info fema es
3. signals etc to current loops or voltage signals for further retransmision while introducing into the system galvanic isolation barriers between the input the output and the power supply circuits ThelSC series of Isolated Signal Converters offer an excellent relation between signal conversion speed and measurement accuracy Offering a 0 2 accuracy and up to a Oms response time depending on the model these units can process information coming from probes or transducers in such a way that can be quickly retransmitted in a fast and accurate form to remote data acquisition systems or PLC s The isolated signal converters of the ISC series are ideal to integrate into 12 bit data acquisition systems Its powerful galvanic isolation of 3 500 V introduces high security to the measuring systems preventing the propagation ofthose phenomenon which usually cause damage to the remote system such as transient peaks or energy shocks in any ofthe circuits of the system The galvanic isolation also acts as a strong CE barrier The decoupling created between the input output and power circuits avoids pernicious effects on the output such as ground loops or signal leaks which distort the acquired data and are extremely difficultto isolate once introduced into the signal The isolation offered by the ISC series of Isolated Signal Converters is a 3 way isolation Thus all the benefits exposed above are applicable to any of the three circu
4. GNETIC COMPATIBILITY D89 336 CEE AMENDED BY D93 68CEE ACCORDING TO RD1950 1995 01 12 REGULATIONS ELECTRICAL SECURITY SUSCEPTIBILITY EN61010 1 EN 50082 2 IEC 1000 4 2 EN 61000 4 2 IEC 801 2 ENV 50140 EN 61000 4 4 IEC 801 4 level 3 ENV 50204 level 3 EMISSION EN 50081 2 EN 55011 EN 55014 EN 55022 UNE 21352 76 CEI 359 71 Operating quality expressions for electronic equipments UNE 20652 80 CEI 284 68 Behaviour rules inherent to the handling of electronic equipments and other similar technics Signed D Junca Quality Manager Barbera del Valles 2002 FEMA ELECTRONICA Page 9 10 CAUTIONS WARNINGS AND NOTES INSTALLATION PRECAUTIONS The installation and the future use of this unit must i be done qualified personnel The unit has not AC mains switch neither internal protection fuse It will be in operation as soon as power is connected The installation must incorporate an external mains switch with a protection fuse and also the necessary devices to protect the operator and the process when using the unit to a control machine or process where injury to personnel or damage to equipment or process may occur as a result of failure of the unit RECOMMENDED FUSES 24Vdc 230Vac 115Vac 250mA O0mA 100mA Time lag Time lag Time lag SAFETY PRESCRIPTIONS The unit has been designed and tested under N EN 61010 1 rules and is delivered in good conditions This User s Man
5. ISOLATED me Serie ISC SIGNAL CONVERTERS WITH GALVANIC ISOLATION 141516 OUTPUT MODEL ISC POT for Potentiometers ISC RES for Resistances FEMA EITE CLR O NIC A lt L 2 9 Y 9 lt gt LL USER S MANUAL HT0403r150908 info fema es www fema es 0 INDEX 1 GENERAL INFORMATION 3 2 INSTALLATION 4 3 DIMENSIONS AND CONNECTIONS 9 4 SIGNAL INPUT JUMPERS 6 5 SIGNAL OUTPUT JUMPERS T 6 READJUSTINGINPUT OUTPUT T 7 TEGHNICAL DATA l 2 dino rato porre 8 INPUT SIGNAL for POTENTIOMETER 8 INPUT SIGNAL for RESISTANCE 8 OUTPUT SIGNAL in 8 OUTPUT SIGNAL in mA 8 POWER SUPPLY 8 MECHANICAL DIMENSIONS 8 GALVANIC ISOLATION 8 MATERIALS 2 8 8 TECHNICAL 9 9 CE DECLARATION OF CONFORMITY 9 10 CAUTIONS WARNINGS AND NOTES 10 11 OTHERPRODUGTS 12 FEMA ELECTRONICA Page 2 1 GENERAL INFORMATION The ISC series of Isolated Signal Converters allow to convert process signals temperatures electrical
6. J8 BE J8 J9 J9 J10 J11 J12 Bo J10 J11 ISC RES Input signal ranges for Resistance measure J11 J12 JJ 10 KOhms 5 KOhms 3 KOhms 1 5 KOhms J7 8 J8 J9 21 J9 J10 21 Bi J10 ss ae FEMA ELECTRONICA Page 6 5 SIGNAL OUTPUT JUMPERS _ The position of the output jumpers selects the range for the output signal as indicated below 0 1 0 10 IMPORTANT Opening the front cover may grant access to areas with dangerous voltages Operations must be performed by qualified technical staff 6 READJUSTINGINPUT OUTPUT To change the input output relation of the instrument proceed as indicated below Following values in brackets are examples for readjusting the input output relation of the instrument to 0 100 0 10 Vdc and input type potentiometer 1 Open the front cover 2 Select the required input jumpers Section 4 page 6 3 Select the required output jumpers Section 5 page 7 4 Connect a potentiometer to the input terminals Section 3 page 5 5 Connect a multimeter to the output terminals 4 and 5 for mA or 4 and 6 for Vdc 6 Generate the low input signal 0 Operate the OFFSET potentiometer until the low output value is reached 0vac 7 Generate the high input signal 100 Operate the SPAN potentiometer until the high output value is reached 10 8 Repeat 6 and 7 to
7. improve the accuracy until it reaches its specified value 9 Close the front cover FEMA ELECTR NICA Page 7 7 TECHNICAL DATA INPUT SIGNAL for POTENTIOMETER RANGES 0 100 0 50 0 25 0 12 5 POTENCIOMETERVALUES Minimum 100 Ohms Maximum 1 MOhm POTENTIOMETER EXCITATION TO MEASURE 1 Vdc INPUT SIGNAL for RESISTANCE RANGES 0 10 KOhms 0 5 KOhms 0 3 KOhms 0 1 5 KOhms RESISTANCE EXCITATION TO MEASURE 0 2mA MAXIMUM VOLTAGE ON INPUT TERMINALS 15 Vdc differential OUTPUT SIGNAL RANGES 0 10Vdc 0 1Vdc Maximum Output 11Vdc aprox Minimum Output 1Vdc aprox MinimumLoad gt 1 OUTPUT SIGNAL in mA RANGES 0 20mA 4 20mA Maximum Output 22mA aprox Minimum Output 1 5mA aprox MaximumLoad lt 400 Ohms POWER SUPPLY DC Power 24Vdc 10 AC Power 230Vac 10 50 60 Hz 115Vac 10 50 60 Hz Consumption lt 3 8VA MECHANICAL DIMENSIONS DC Powered 22 5 x93 x110 mm AC Powered 37 0x93x110 mm Weight DC 120gr Weight AC 200 gr Standard DIN rail mounting DIN46277 DIN EN 50022 37 5 x 7 5 mm 1 38 x 0 3 7 GALVANIC ISOLATION DC Powered Units Input Output 3K5 60 seconds Power Input 3K5 60 seconds Power Output 1KV 60 seconds AC Powered Units Input Output 3K5 60 seconds Power Input 3K5 60 seconds Power Output 3K5 60 seconds All isolation levels are tested during atime of 60 seconds with Vac TrueRMS signal and current leaks 1mA Note Indicated i
8. its composing the instrument input output and power Recalibration of the instruments is realized in a fast and easy way Opening the front cover grants access to the configuration jumpers Additional Span and Offset potentiometers are directly accessible from the frontal part These potentiometers are highly decoupled minimizing the iterations needed to obtain a correct adjustment In order to obtain a higher and quickest benefit ofthe ISC units we recommend you to read carefully the information provided in this manual before proceeding to the installation ofthe instrument In this manual you willfind all technical data both electrical and mechanical needed for a correct instalation and utilization Note The ISC Isolated Signal Converter instruments have a characteristics label attached on the side of the instrument Check that the information indicated on the label matches with your application requirements and specially check that the value and type of the power supply needed matches the value and type of the power supply availble on your installation FEMA ELECTR NICA Page 3 2 INSTALLATION Before installing the instrument check the characteristics label attached to the side of the unit Specially check that the value of the power supply needed matches the power supply available on your installation The characteristics label also indicates the input output signal relation for the instrument Remember to ta
9. ke note of the new input output relation if you proceed to readjust the instrument To access the selection jumpers for input and output ranges and the Span and Offset potentiometers slightly press the A A points of the front cover as indicated on Figure OUTPUT JUMPERS Pot SPAN Por OFFSET INPUT JUMPERS FIGURE 2 FIGURE 1 rr FRonTCoverR FIGURE 3 The instrument must be installed in such a way that it remains in vertical position as indicated on Figure4 To help dissipate the heat a free space of 2mm must be left available on both sides of the instrument 2mm FIGURE 4 IMPORTANT Opening the N front cover may grant access to areas with dangerous voltages Operations must be performed qualified technical staff FEMA ELECTR NICA Page 4 Output Connections OUTPUT Input Connections CaBLe SHIELD CONNECTIONS FOR CONNECTIONS FOR POTENTIOMETER RESISTANCE 24 5 q HOUSING WIDTH FOR DC PowERED AC POWERED AC POWERED CONNECTIONS CONNECTIONS INSTRUMENTS 9mm 0 35 93mm 3 66 22 5mm 0 87 FEMA ELECTRONICA Page 5 4 SIGNAL INPUT JUMPERS The position of the input jumpers selects the range for the input signal as indicated below ISC POT Input signal ranges for Potentiometer measure 100 50 25 12 5 ss se
10. personnel or companies without the official authorization of FEMA ELECTRONICA S A This warranty is also VOID for damages caused by defective or inappropriate applications RETURNS FORREPAIR Ship free of charges and properly packed to the address indicated below FEMAELECTRONICA S A Pol Ind Santiga Altimira 14 T 14 N 2 E 08210 Barbera del Vall s BARCELONA ESPANA SPAIN If the unit shows signs of damage is not able to show the expected measures has been stored in a bad conditions or a protection failure happened then do not attempt to operate keep the unit out of service and send for repair IN CASE OF FIRE 1 Disconnect the unit from the power supply 2 Give the alarm according to the local rules 3 Switch off all air conditioning devices 4 Attack the fire with carbonic snow do not use water in any case WARNING In closed areas do not use systems with vaporized liquids In case of malfunction the unit should be sent to the manufacturer for its evaluation Within the warranty period and always previous examination from FEMA ELECTR NICA S A the unit will be repaired or replaced to the discretion of the manufacturer Limitation of liability FEMA ELECTRONICA S A shall not be responsible for any damage or loss to other equipment however caused which may be experienced as a result of the installation or use of this product FEMA ELEC TRONICA S A liability shall not exceed the purchase price
11. solation levels are also sometimes named as STRENGTHENED ISOLATION levels for systems with Polution Level 2 MATERIALS Box and Cover in Poliamide PA6 UL94 V 2 blue color Terminals in Poliamide UL94 V 0 FEMA ELECTR NICA Page 8 8 TECHNICAL DATA Il Accuracy Linearity Thermal Drift Response Time Warm Up Time Electrical Connections Maximum Wire Section Protection Operating Temperature Storage Temperature lt 0 2 F S Optimized for 12 bit systems lt 0 1 F S 250 ppm C Typical lt 70 5 90 of signal 3Hz 3dB 15 minutes Plug in Screw Terminals 2 5 IP 30 0 to 60 C 20 to 70 C 9 CE DECLARATION OF CONFORMITY Manufactured by Address FEMAELECTRONICA S A Pol Ind Santiga Altimira 14 T14 2 E 08210 Barber del Vall s BARCELONA ESPANA SPAIN We hereby declare under our responsibility that the equipments identified below comply with the following specifications Series Models Isolated Signal Converter of the ISC Series P PT100 TJ TK TE TT IR TS VAC VDC IAC IDC POT RES HZ LC DIRECTIVES EUROPEAN DIRECTIVE FOR LOW VOLTAGE D73 23 CEE AMENDED BY D93 68 CEE Equipments powered from 50 to 1000 Vac and or from 75 to 1500 Vdc EUROPEAN DIRECTIVE FOR PRODUCT SAFETY D92 59 CEE ELECTROTECHNICAL REGULATION FOR LOW VOLTAGE RBT ITC21 ITC 29 ITC 35 For equipments with power supply lower than 50Vac and or 75Vdc EUROPEAN DIRECTIVE FOR ELECTROMA
12. ual contains useful information the user has to respect in order to warrant a proper function of the unit and good security conditions The unit is designed for internal applications with good ventilation to avoid excessive heating It can occasionally be applied to temperatures down to 10 C or up to 70 C without security degradation Do all connections before applying power to the unit Do not make wiring changes until power is disconnected from the unit Install the unit far from elements generating electric noise or magnetic fields such as power relays electrical engines speed regulators etc Do not use until installation is completed POWER SUPPLY The power supply must be connected to the adequate terminals 1 2 and 3 The characteristics of the power supply are shown on the side label Please make sure that the unit is correctly connected to a power supply of the correct voltage and frequency Do not connect the unit to lines which are overloaded or which provide power to systems working on ON OFF cycles or inductive loads ATTENTION For instruments which are DC powered respect the polarity of the power terminals as indicated on this user s manual and on the instrument itself SIGNAL WIRING Certain considerations must be given when installing the signal input wires If the wires are long they can act as an antenna introducing electrical noise into the unit Therefore Do not install the signal input wires
Download Pdf Manuals
Related Search