MR7 Electronic Control Unit
Contents
1. MR7 Electronic Control Unit Electronic control unit with 433 92 Mzh receiver for the remote control of a 230Vac current socket TECHNICAL DATA Power supply 230V 50 60Hz 3KW max User output 230V 3KW Max Working temperature 10 55 C Narrow band radio receiver 433 92 MHz Compatible radio controls 12 18 Bit Rolling Code Amount of Radio controls that can be memorised 8Max 100 x 55 x 90 mm ABS UL94V 0 IP40 Dimensions Container SEL SEL INSTALLATION OF THE RECEIVER For excellent functioning it is very important to choose the place of installation carefully Capacity is not only conditioned by the technical features of the device but also varies depend ing on the radio electric conditions of the site The receiver has an incorporated antenna INITIAL FUNCTIONING CONDITION The device can only work coupled with one or more radio controls upon first ignition the control unit does not contain any radio control code in the memory FUNCTIONING MODE The control unit used coupled with one or more radio controls will allow the remote control of the charge applied to the cur rent socket Depending on the Dip Switch SW1 selection in side the device four different functioning methods times are obtained Step by Step to every control given through the previ ously memorised radio control will correspond the acti vation or deactivation of the 230Vac current socket for the remot2. e control of an applied device Timed 1 Minute to every control given through the pre viously memorised radio control will correspond the temporary activation equal to 1 minute of the 230Vac current socket for the remote control of an applied de vice Timed 15 Minute to every control given through the previously memorised radio control will correspond the temporary activation equal to 15 minutes of the 230Vac _h current socket for the remote control of an applied de vice Monostable the activation of the 230Vac current socket for the remote control of an applied device will only be had when the control given through a previously memo rised radio control will be continuously maintained ON ON ON ON 1 2 1 2 1 2 1 2 TEMP STEP BY STEP 1 MINUTE TEMP 15 MINUTES MONOSTABLE PROGRAMMING METHOD OF THE RADIO CONTROL The programming of the Radio controls to be associated is the Self learning type and is performed in the following way press the SEL key three sounds will be heard as confirmation of programming input press the key of the radio control to be programmed continuously for 5 seconds at the same time the control unit will emit a confirmation sound programming will be completed and the control unit will exit the programming phase Whereas if after having pressed the SEL key no code is sent within 15 seconds the control unit will emit four confirmation sounds signalling the end of the programming phase I
3. require the opening of the casing cables connection programming etc must be carried out by expert personnel during installation For any further operation which requires the casing to be re opened re programming repair or installation amendments contact the after sales assistance STATEUROP declares that the product MR7 is in compliance with the specifications of R amp TTE Directives 99 5 EC EMC 2004 108 EC LVD 2006 95 EC Directives STATEUROP sistemas at eg para europa 5 a Rua do Sobreiro Lugar do Pinheiro Rio C y St Eug nia Apto 5018 EC Barcelos 4754 908 Rev 1 0 01 04 10
4. t is possible to repeat the programming operations described above for the insertion in the memory of further control unit codes up to a maximum of 8 codes In case the memory al ready contains 8 memorised codes by carrying out the pro gramming procedure the control unit will emit six confirming sounds warning that the memory available is full SOUND SIGNALS 1 BIP Radio control code memorised 3 BIP Programming phase start 4 BIP Programming phase end 5 BIP Deletion of the memorised radio control codes 6 BIP Memory End available for new code RESET Should it be necessary to restore the control unit to default setting press the SEL key continuously for 5 seconds the control unit will emit five confirmation sounds and the opera tion will be complete Rev 1 0 01 04 10 IMPORTANT FOR THE INSTALLER The device must never be used by children or persons with reduced physical psychological abilities unless supervised or trained on the functioning and the use modalities Do not allow children to play with the device and keep the ra dio controls away from their reach ATTENTION keep this instruction manual and respect the important safety prescriptions contained herein The non com pliance with the prescriptions may cause damages and serious accidents Frequently examine the plant to detect any signs of damag ing Do not use the device if a repair intervention is necessary Attention All operations which
Download Pdf Manuals
Related Search