Home

3. display installation - CNET Content Solutions

1. 2 Fasten the foot on the desk with 4x M4 screws length of the screws depending on the depth of the desk 3 11 VESA mount installation IN CAUTION Use suitable mounting apparatus to avoid risk of injury WARNING Never move a display attached to an arm by pulling or pushing the display itself Instead make sure that the arm is equipped with a VESA approved handle and use this to move the display Please refer to the instruction manual of the arm for more information and instructions WARNING Use an arm that is approved by VESA according to the VESA 200 x 100 mm or VESA 100 x 100 mm standard Use an arm that can support the weight of the display Refer to the technical specifica tions of this display for the applicable weight K5902079 CORONIS UNITI 19 12 2014 AAA 19 3 Display installation 20 CAUTION You should mount the panel in landscape position Portrait position is pos sible but not supported WARNING To avoid muscle strain or back injury use lifting aids and proper lifting tech niques when removing or replacing Overview The panel standard attached to the tilt amp swivel foot is compatible with the VESA 200 x 100 mm and VESA 100 x100 mm standard So it can be used with an arm stand according to the VESA 200 x 100 mm or VESA 100 x 100 mm standard
2. 3 2 Unlocking the tilt mechanism gt In the factory the tilt system in the display stand is locked with a red pin to prevent dam age during transportation You ll have to remove this pin before adjusting your display position Push the display against the buffer part to easily remove the pin To remove the pin 1 Position the display with its rear side facing you 2 Pull out the red pin in the display stand 3 Keep the pin in case the display needs to be shipped later WARNING Before transportation of the display insert the pin in the lock mechanism so that the grey color of the pin isn t visible anymore 3 3 Unlocking the height mechanism In the factory the height positioning system in the display stand is locked with a red pin to prevent damage during transportation You ll have to remove this pin before adjusting your display height position 0 K5902079 CORONIS UNIT 19 12 2014 3 Display installation To remove the pin 1 Position the display with its rear side facing you 2 While holding the display panel pushed down pull out the red pin in the display stand 3 Keep the pin in the dedicated hole in case the display needs to be shipped later To retain the pin for possible future transportation insert the short red end of the pin back into the stand of your display 3 4 Adjusting the display position lt In the factory the height positionin
3. 2x DisplayPort Main cables UK European CEBEC KEMA USA UL CSA adaptor plug NEMA 5 15P Chinese CCC Unsperpa 8 Operating umay 20 SERRA 7 8 Open source license information 58 Open source license information Open source license usage This product contains software components released under an Open Source license A copy of the source code is available on request by contacting your Barco customer support representative EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTOR BE LIABLE FOR DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES MORE INFORMATION DETAILS IS TO BE FOUND IN EACH SPE CIFIC OPEN SOURCE LICENSE Copyright on each Open Source Software component belongs to the respective initial copyright holder each additional contributor and or their respective assignee s as may be identified in the respective doc umentation source code README file or otherwise You shall not remove or obscure or otherwise alter the respective copyrights You acknowledge living up to the conditions of each separate Open Source Software license A list of the Open Source Software components used is available in the applicable EULA
4. Bring up the OSD main menu 2 Navigate to the Configuration gt Lights menu 3 Enter the SoftGlow Wall light brightness submenu 4 Seta SoftGlow Wall light brightness value as desired and confirm 5 8 DPMS mode About DPMS mode Enabling the Display Power Management System DPMS mode on your display will optimize its diagnos tic lifetime by automatically switching off the backlight when the display is not used for a specified period of time By default DPMS mode is enabled on your display but it also needs to be activated on your workstation To do this go to the Power options properties window of your workstation Barco recommends setting DPMS activation after 20 minutes of non usage EE When DPMS mode is enabled on your display an additional OSD power saving function becomes available hibernate Please refer to Hibernate page 32 for more information on hibernation and how to enable this function To enable disable DPMS mode on your display 1 Bring up the OSD main menu 2 Navigate to the Configuration Power Management menu 3 Enter the DPMS Mode submenu 4 Select Enabled Disabled as desired and confirm K5902079 CORONIS UNITI 19 12 2014 AAA 5 Advanced operation 5 9 Hibernate About hibernate Enabling hibernation will not only switch off the backlight but will also force the display to disable other functionalities so that power consumption is further reduced to a minimum This happens after a
5. Navigate to the Configuration Calibration Color Settings menu 3 Enter the Color Definition submenu 4 Select Color Coordinates and confirm 5 Enter the x and or y submenu 6 Set the coordinate value for x and or y as desired and confirm 5 16 Viewing modes About viewing modes The Coronis Uniti can be used in two viewing modes 34 DD K5902079 CORONIS UNITI 19 12 2014 5 Advanced operation Diagnostic This mode provides the full calibrated luminance and is intended for using the display for diagnostic purposes Text In this mode the luminance is reduced to approximately half of the luminance This is intended for using the display with office applications such as word processing Please note that text mode is not persistent once powered off the unit will restart in diagnostic mode To quickly switch the viewing mode without having to enter the OSD menu touch the left and right key the two leftmost buttons at the same time during normal operation x As the Coronis Uniti is intended to be used in a diagnostic environment the diagnostic mode should always be selected To select a viewing mode 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration menu 3 Enter the Viewing Mode submenu 4 Select Diagnostic Text as desired and confirm 5 17 Display functions About display functions Native uncorrected panels will display all grayscale color levels with luminanc
6. Not used USB upstream connector USB downstream connector USB downstream connector USB downstream connector 2 3 Accessories Film clip The film clip can be used to hold a radiological film when using the I Luminate function as a light box Image 2 4 Film clip K5902079 CORONIS UNITI 19 12 2044 7 2 Parts controls and connectors MultiTouchPad The MultiTouchPad enables and controls SpotView Image 2 5 MultiTouchPad 8 5902079 CORONIS UNITI 19 12 2014 3 Display installation 3 DISPLAY INSTALLATION Prior to installing your Coronis Uniti and connecting all necessary cables make sure to have a suitable display controller physically installed in your computer If you are using a Barco display controller please consult the user guide delivered with it to do this For a list of compatible display controllers please refer to the latest version of the com patibility matrix available on myBarco com myBarco My Support Healthcare Com patibility Matrices Barco Systems Compatibility Matrices 3 1 Removing the connector compartment cover The connector compartment cover should be removed to get access to the connectors To remove the connector compartment cover 1 Gently push the two lips on the top of the cover 2 Pull the top of the cover slightly away from the display and lift the cover upwards 3 Remove the cover K5902079 CORONIS UNITI 19 12 2014 __ FD 3 Display installation
7. discover errors please let us know Barco software products are the property of Barco They are distributed under copyright by Barco N V or Barco Inc for use only under the specific terms of a software license agreement between Barco N V or Barco Inc and the licensee No other use duplication or disclosure of a Barco software product in any form is authorized The specifications of Barco products are subject to change without notice Trademarks All trademarks and registered trademarks are property of their respective owners Copyright notice This document is copyrighted All rights are reserved Neither this document nor any part of it may be reproduced or copied in any form or by any means graphical electronic or mechanical including photocopying taping or information storage and retrieval systems without written permission of Barco 2014 Barco N V All rights reserved 7 7 Technical specifications 56 Overview Screen technology IPS Active screen size diagonal 853 44 mm 33 6 Active screen size H x V 708 1 x 472 1 mm 27 8 x 18 6 3 2 Aspect ratio H V Resun 7 200 x 2800 Pixel pitch 0 1686 mm K5902079 CORONIS UNITI 19 12 2014 7 Important information Coorimagng Gray imaging Color support Yes Viewing angle H V 178 CR 2 10 Uniform Luminance Color PPU Technology ULT Per Pixel Uniformity PPU ALC BLOS LU MNT DICOM calibrated luminance 1000 cd m UL
8. not remove cover No serviceable parts inside Refer servicing to qualified personnel Do not expose this apparatus to rain or moisture Modifications to the unit Do not modify this equipment without authorization of the manufacturer Type of protection electrical Display with external power supply Class equipment Degree of safety flammable anesthetic mixture Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide Non patient care equipment e Equipment primarily for use in a health care facility that is intended for use where contact with a patient is unlikely no applied part The equipment may not be used with life support equipment The user should not touch the equipment nor its signal input ports SIP signal output ports SOP and the patient at the same time Power connection Equipment with external 24 VDC power supply e Power requirements The equipment must be powered using the delivered medical approved 24 VDC SELV power supply The medical approved DC power supply must be powered by the AC mains voltage The power supply is specified as a part of the ME equipment or combination is specified as a ME system To avoid the risk of electric shock this equipment must only be connected to a supply mains with protective earth The equipment should be installed near an easily accessible outlet The equipment is inte
9. specific period of time which can be manually adjusted Hibernate can only be enabled on your display when the DPMS mode is enabled first Therefore please refer to DPMS mode page 31 to do this To enable disable hibernation on your display 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Power Management menu 3 Enter the Hibernate submenu 4 Select Enabled Disabled as desired and confirm To specify the hibernate timeout 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Power Management menu 3 Enter the Hibernate Timeout submenu 4 Set the timeout value as desired and confirm 5 10 I Luminate default mode 32 About the I Luminate default mode The I Luminate mode defines the default activated mode during the I Luminate boost This mode can be Screen The boost mode is applied on the screen display Film large or small Film large or small the boost mode activates a high illuminated rectangle on top of the screen simulating a light box for use with radiological film The size of this rectangle is similar to a classic large or small radiological film To set the Luminate mode 1 Bring up the OSD main menu 2 Navigate to the Configuration gt I Luminate menu 3 Enter the Default mode submenu 4 Select Screen Small Film Large Film as desired and confirm K5902079 CORONIS UNITI 19 12 2014 5 Advanced operation 5 11 I Luminate film
10. the power status indicator light will be white when the display is switched on x When the display is in stand by mode the power status indicator light will always turn orange even when the power status indicator light is disabled To enable disable the power status indicator light 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Indicator Lights menu 3 Enter the Power Status submenu 4 Select Enabled Disabled as desired and confirm K5902079 CORONIS UNITI 19 12 2014 __ 29 5 Advanced operation 5 4 Key indicator lights About the key indicator lights By default after lighting up the key indicator lights will dim again if no further actions are taken within the following 5 seconds However this behavior can be changed so that the key indicator lights are always on or always off To configure the key indicator lights 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Indicator Lights menu 3 Enter the Keys submenu 4 Select Automatic Always On Always Off as desired and confirm 5 5 Power lock function About the power lock function By enabling the power lock function the Coronis Uniti is forced to remain switched on This means that it can t be switched to stand by mode manually until the power lock function is disabled again To enable disable the power lock function 1 Bring up the OSD main menu 2 Navigate to the Configu
11. 1 and DPCD V1 2 To select the EDID format 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Sources gt Input Settings gt DisplayPort1 2 menu 3 Enter the nput interface standard version submenu K5902079 CORONIS UNITI 19 12 2014 AAA 5 Advanced operation 4 Select one of the available versions and confirm To obtain full resolution 2100 x 2800 and full refresh rate 60Hz DPCD V1 2 should be selected 5 26 EDID format About EDID format The Coronis Uniti supports two EDID formats E EDID V1 4 and DisplayID V1 3 To select the EDID format 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Sources gt Input Settings gt gt DisplayPort 1 2 gt EDID menu 3 Enter the EDID format submenu 4 Select one of the available format and confirm 5 27 EDID timings About EDID timings Following EDID timings are available for your Coronis Uniti Refresh Rate Allows to manually select the refresh rate of the image source video input signal depending on the maximum refresh rate of the display controller connected to your display Preferred Orientation Allows to change the orientation of the image Source video input signal to landscape portrait or to let the display automatically assign the correct orientation Color Depth Alos to change the color depth to 8 or to 10 bit To manually set EDID timings 1 Bring up the OSD main menu 2 Navig
12. 50 60 Not applicable Power frequency Hz magnetic field magnetic fields should IEC 61000 4 8 be at levels characteristic of a typical location in a typical commercial or hospital environment Conducted RF 3 Vrms 3 V Portable and mobile RF communications IEC 61000 4 6 150 kHz to 80 MHz equipment should be Radiated RF 3 V m 3 V m used no closer to any IEC 61000 4 3 80 MHz to 2 5 GHz parn orahe Gorons Uniti including cables than the recommended separation distance 1 is the a c mains voltage prior to application of the test level 2 Coronis Uniti doesn t contain susceptible components to magnetic fields 52 n K5902079 CORONIS UNITI 19 12 2014 7 Important information Immunity test IEC 60601 Compliance level Electromagnetic environment guidance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance d 1 2 P d 1 2 P 80 MHz to 800 MHz d 2 34 P 800 MHz to 2 5 Ghz Where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Test levels Field strengths from fixed RF transmitters as determined by an electromagnetic site survey should be less than the compliance level in each frequency range 4 Interference may occur in the vicinity of equipment marked with symbol 5 At 80 MHz and 800 MHz the hi
13. 60601 Compliance level Electromagnetic environment guidance Electrostatic discharge 6kV contact 6kV contact Floors should be wood ESD 8kV air 8KV air concrete or ceramic tile IEC 61000 4 2 K If floors are covered with synthetic material the relative humidity should be at least 30 Electrical fast 2kV for power supply 2kV for power supply Mains power quality transient burst lines lines should be that of a typical IEC 61000 4 4 1kV for input output 1kV for input output COmmercial or hospital lies litis environment Surge 1 KV line s to line s 1 kV line s to line s Mains power quality IEC61000 4 5 2 kV line s to earth 2 kV line s to earth SAOUId be that of a typical commercial or hospital environment Test levels Voltage dips short lt 5 Ur 1 gt 95 dip in lt 5 Uy gt 9596 dip in Mains power quality interruptions and voltage Ur for 0 5 cycle Ur for 0 5 cycle should by that of a variations on power T NES T DS typical commercial or supply input lines us Ha OO dip mela 40 U rS di mL hospital environment If for 5 cycles for 5 cycles the user of the Coronis eee Oe 70 Ur 30 dip in Ur 70 Ur 30 dip in U Uniti requires continued for 25 cycles for 25 cycles operation during power o S En es o EON mains interruptions it is opum dipam To dip in recommended that the T T Coronis Uniti be powered from an uninterruptible power supply or a battery Power frequency
14. A eee deere 29 5 4 Key indicator lights srir aaeeei eR RR LU a ele ene 30 5 5 Power lock function oen sss otedHese AA WERRRE EHE nada han hdi 30 9 6 SoftGlow Task light vitoria dir e ERE PEU M do dus 30 of SoftGlow Wal ight irrita idad oa VER RERBA UA PLU 31 5 8 DPMS Mode oneri ied bte eU EE aan tire banner 31 9 9 ur ETT 32 5 10 I Luminate default mode 4 44444444h eee e a esed ce ene aa adden nn hh aan ndn 32 5 11 IFEuminate film pOSItlOns ou iiber rebuild A Un nad Pesto epe meet M Idae 33 5 12 Luminance target i iria illo aot bone eee s been wide 33 5 19 Color presets eot Sek ett He dere inedit ti beet bil oot E LU Me bd 33 514 Color temperature aa MAR insit atrocidad io 34 5 15 Color coordinates 5 5 phe Spbbie be ters stibto bn be e reb Up EE LA Ub e 34 5 16 VIEWING modes tgctesststittelonnb bed srbble Deedter ee PPbtt eben ue est eb bea obese unb E Dent v dde 34 SAF Display UNCTIONS M E 35 5 18 Ambient Light Compensation ALC sis 36 5 19 Reading TOOMS shes ea Ar aa s E ae ecran A ordei eter tata 36 9 20 Continuous Alicia ce RR nn tete il DR en UDIN een ne been dass 37 5 21 Embedded QA serrar er darla Reina AAA ERE Up ERE A ae aaoo eda ana tena nine ERA dues 37 5 21 1 About Embedded QA 2 eedem seme e e LA re 38 K5902079 CORONIS UNITI 19 12 2014 A Table of contents 5 21 2 DICOM status report 444444 s
15. Coronis Uniti User Guide MDMC 12133 K5902079 02 BARCO 19 12 2014 Visibly yours Barco nv President Kennedypark 35 8500 Kortrijk Belgium Phone 32 56 23 32 11 Fax 32 56 26 22 62 Support www barco com esupport Visit us at the web www barco com Printed in Belgium Table of contents TABLE OF CONTENTS 1 WGICODIGL uio deu A E SEI Mg EEE RNA TO Ent I os ns Es 3 1 4 About the product AEE EE A da ee Rode de E RARO dea eae et ain 3 LR A AR re SOG EE ad Pagel daa dana eae aa COS 3 2 Parts controls and connectors ss 5 AT Display front View oer orones dre ER REP Lie a A RARA Ree E XXE 5 2 2 Display IV Wicca eet T ener D eL aee ER RI 6 2 3 e c 7 3 Display installation a enu a e 9 3 1 Removing the connector compartment cover 9 3 2 Unlocking the tilt mechanism eme eme sen 10 3 3 Unlocking the height mechanism 10 3 4 Adjusting the display position enn 11 3 5 Connecting the signal cables seesssssssess messen he nh hahaha n rh A aho inna 12 3 6 Connecting the power cable 2 0 ccc cece eee EEE n ees he errar sn nha ana ah EED 14 3 7 Mountirig the film Clip 2e tet adiamiideiente EEEE ARA AER RR ERE EA HA dd de 15 3 8 Mounting the MultiTouchPad e semen msn 16 3 9 Routing
16. IS UNITI 19 12 2014 5 Advanced operation Display function Shows the current display function Ambient Light Compensation Shows the ambient light compensation status Reading room Shows the selected reading room To retrieve the DICOM status report 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Select DICOM status report to make the information visible on the screen 5 21 3 DICOM compliance check About DICOM compliance check The DICOM compliance check will measure the DICOM curve of your display in different steps After measurement the DICOM status report is shown To start DICOM compliance check 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Select DICOM compliance check to start the compliance check Warning Pressing a key during the compliance check will abort the check 5 21 4 DICOM calibration About DICOM calibration The DICOM calibration will add a correction to the current DICOM curve to approach the perfect DICOM curve as good as possible To start DICOM calibration 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Select DICOM calibration to start the calibration Warning Pressing a key during calibration will abort the calibration previous values will be restored Note After calibration the compliance check will start
17. If you use an unstable cart or stand the device may fall causing serious injury to a child or adult and serious damage to the device This apparatus conforms to IEC 60950 1 2005 C1 2006 A1 2009 C1 2012 A2 2013 EN 60601 1 2007 A11 2011 IEC 60601 1 2005 A1 2012 ANSI AAMI ES 60601 1 2005 A1 2012 CAN CSA C22 2 No 60601 1 2014 IEC 60601 1 2 2007 EN 60601 1 2 2007 AC 2010 FCC Class B ICES 001 Class B VCCI Class A ya WARNING VCCI Class A TIOE QIZATRRMHEECT OFBER ERI CHATS CENA E CT CEMBVYVET CORA ARAM BIER EBSTSKIBRKENZCEMBVET National Scandinavian Deviations for CL 1 7 2 Finland Laite on liitettava suojamaadoituskoskettimilla varustettuun pistorasiaan Norway Apparatet m tilkoples jordet stikkontakt Sweden Apparaten skall anslutas till jordat uttag 7 2 Environmental information 48 Disposal Information Waste Electrical and Electronic Equipment A E This symbol on the product indicates that under the European Directive 2012 19 EU governing waste from electrical and electronic equipment this product must not be disposed of with other municipal K5902079 CORONIS UNITI 19 12 2014 7 Important information waste Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these item
18. MediCal QAWeb Server offers even more possibilities Learn more and sign up for the free MediCal QAWeb Essential level at www barco com healthcare ga 4 2 Key indicator lights About the key indicator lights By default the indicator lights of the keys will be dimmed which makes the keys unavailable at that mo ment To make the keys illuminate and available for further actions touch one of the keys As a result all keys will be illuminated and are now available for further actions However if no further actions are taken within the following 5 seconds the keys will dim again The I Luminate Left key is always lit and available for activation of the I Luminate fea ture Please refer to I Luminate page 27 for more information The key auto dim function can be disabled in the OSD menus Please refer to Key in dicator lights page 30 for detailed instructions on how to do this 4 3 Standby switching 24 a The connected power supply also provides a switch that can be used to turn the power completely off To use the display please make sure to switch on this power supply This can be done by pushing the on off switch on the power supply into the position To switch your display on using the keys Switching on the display while it is in standby mode can be done by 1 Push the standby key once As a result the display will switch on and the power status indicator light is white a During start up phase the o
19. ORONIS UNITI 19 12 2044 49 7 Important information SH 8 I ASAS Y acd Component name Hazardous substances and elements E a E A ZRKA RR Pb Hg Cd Cr6 PBB Bi PBDE Paper Manuals Jc ER CD manual O dcr lU SE E PR TEE BEP 1 EIER I S EIS SJT 11363 2006 M R XE OR 9 ESK ELT O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ T11363 2006 X dcn VB mCB SUBE p TET BUE RU 3E 15 Er ML FER SEE SJ T 11363 2006 rem EH REZX X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ T11363 2006 TE rh BA Bi ET AR SA EA i EIP aR 27 588 e E A i BET HS RRE RA RAE Wh E Ep E FA ABR EFUP ER S Barco da Pr A JEFUPRE ASA TUS A AB AY AE ER amp amp T P ESL Fi REA i PP UR AA RR E All Electronic Information Products EIP that are sold within Chinese Mainland must comply with the Electronic Information Products Pollution Control Labeling Standard of Chinese Mainland marked with the Environmental Friendly Use Period EFUP logo The number inside the EFUP logo that Barco uses please refer to the photo is based on the Standard of Electronic Information Products Environmental Friendly Use Period of Chinese Mainland Gy 7 3 Regulatory compliance information 50 Indications for use The Coronis Uniti is intended to b
20. T off Contrast ratio typical 1200 1 PPU on Response time Tr Tf 33 ms Scanning frequency 25 85 Hz Housing color RAL 9004 RAL 9003 Video input signals DP1 2 USB ports 4 1 upstream 3 downstream Power requirements nominal 100 240 V Power consumption nominal 190 W Power save mode ves Power management VESA DPMS Dotdock fee OSD languages English German French Dutch Italian Spanish Portuguese Swedish Chinese simplified Japanese Korean Arabic Polish Russian Dimensions with stand W x H 795 x 610 x 300 mm lowest position x D Dimensions w o stand W x H 795 x 572 x 131 mm x D Dimensions packaged W x H 1960 x 715 x 395 mm x D 3 Net weight wih stand Net weight w o stand 24 kg Net weight packaged with 42 kg stand MiweghpskagelwosmwINA O OOOO Height adjustment range 95 mm m 7 ere Seve Te Prot NA Mounting standard VESA 200 x 100 mm amp 100 x 100 mm Screen protection Protective non reflective glass cover Recommended modalities Radiology mammography and digital breast tomosynthesis K5902079 CORONIS UNITI 19 12 2044 57 7 Important information IEC 60950 1 2005 C1 2006 A1 2009 C1 2012 A2 2013 EN 60601 1 2007 A11 2011 IEC 60601 1 2005 A1 2012 ANSI AAMI ES 60601 1 2005 A1 2012 CAN CSA C22 2 No 60601 1 2014 IEC 60601 1 2 2007 EN 60601 1 2 2007 AC 2010 FCC Class B ICES 001 Class B VCCI Class A Quick Installation Sheet Video cables
21. Therefore the tilt amp swivel foot must be removed from the panel 1 Fasten the height mechanism of the foot by putting the red pin in the hole Unlocking the height mech anism page 10 2 Putthe display face down on a clean and soft surface Be careful not to damage the panel screen 3 Loosen the plastic covers with a cross head screwdriver K5902079 CORONIS UNITI 19 12 2014 3 Display installation 4 Remove the two plastic covers K5902079 CORONIS UNITI 19 12 2014 AAA 3 Display installation 6 Attach the arm stand firmly to the panel using 6 screws M4 x 6 mm for a 200 x 100 mm VESA solution or 4 screws M4 x 6 mm for a 100 x 100 mm VESA solution itself Instead make sure that the arm is equipped with a VESA approved handle and IN WARNING Never move a display attached to an arm by pulling or pushing the display use this to move the display Please refer to the instruction manual of the arm for more information and instructions 3 12 First time starting up Overview You are now ready to start up your Coronis Uniti for the first time 1 Switch on your Coronis Uniti as described in Standby switching page 24 2 Turn on the computer connected to your display If you have properly installed your display and display controller the Windows start up messages will appear once the boot procedure is finished 5 Your Coronis Uniti display will be running in a basic video mode at a default refresh
22. although it is recommended to use the USB upstream connector for faster communication 3 6 Connecting the power cable To connect the power cable to the display 1 Connect the supplied external DC power supply to the 24 VDC power input of your Coronis Uniti display 14 OOO K5902079 CORONIS UNITI 19 12 2014 3 Display installation Warning Fasten the power connector to your display with the screws provided at the sides of the con nector 2 Plug the other end of the external DC power supply into a grounded power outlet by means of the proper power cord delivered in the packaging S Use the external power supply delivered with your display If you do not use the correct power supply the display will not start up 3 Mounting the film clip To mount the film clip The film clip can be mounted on the top side of the display 1 Position the film clip on the top side of the bezel at the desired location in the middle left or right K5902079 CORONIS UNITI 19 12 2014 15 3 Display installation 2 To remove the film clip lift the front end or rear end of the clip 3 8 Mounting the MultiTouchPad To mount the MultiTouchPad 1 Connect the MultiTouchPad to one of the USB downstream connectors using either those found in the cable compartment or on the right side of the display 2 With the MultiTouchPad attached and the driver installed simply press on the MultiTouchPad to move the focus on the SpotV
23. ar again OSD menu automatic close function page 29 for detailed instructions on how to do The OSD menu auto exit function can be disabled in the OSD menu Please refer to this 4 5 Navigating through the OSD menus How to navigate through the OSD menus Navigating through the OSD menus can be done by Use the left right keys to move through the sub menus change values or make selections Togo into a submenu or confirm adjustments and selections use the menu key e Use the standby key to cancel adjustments or exit a sub menu Exit all OSD menus at once by touching the standby key for approximately 2 seconds a The key icons are displayed above the keys adapted to the function that it is used for menu dependent K5902079 CORONIS UNITI 19 12 2014 AAA 4 Daily operation I Luminate is not available while the OSD menu is activated Overview key icons Menu Enter Cancel Standby IEC 60417 5009 4 6 Overview of the functionality of the Left Right keys Overview Left key Right key Behavior Cycle viewing mode between text diagnostic Push No Push a on Luminate Right key Menu Behavior PET No push No menu SRE off I Luminate a push Push No menu Cycle I Luminate modes between text small film large film no film Push Push No menu Cycle viewing mode between text and diagnostic also toggle off l Luminate 26 K5902079 CORONIS UNITI 19 12 2014 4 Daily operation Left key Rig
24. ate to the Configuration gt Image Sources gt Input Settings gt DisplayPort 1 2 menu 3 Enter the EDID submenu 4 Select Resolution Refresh Rate Preferred Orientation or Color Depth 5 Select one of the available settings and confirm 5 28 Display info About display info Your display serial number color type native resolution firmware versions etc are available in a dedi cated submenu of the OSD menu 42 DD K5902079 CORONIS UNITI 19 12 2014 5 Advanced operation To retrieve info about your display 1 Bring up the OSD main menu 2 Navigate to the About this Display menu to make the information visible on the screen 5 29 Display status About display status The Status submenu of the OSD menu provides info on the current status of your display runtimes tem peratures etc the status of the connected image sources video encoding mode timings etc the current calibration status of your display display function luminance ALC etc and the status about activated connections To retrieve the status of your display 1 Bring up the OSD main menu 2 Navigate to the Status menu 3 Enter the Display Image Sources Calibration or Connectivity submenu as desired K5902079 CORONIS UNITI 19 12 2014 AAA 5 Advanced operation 44 K5902079 CORONIS UNITI 19 12 2014 6 Cleaning your display 6 CLEANING YOUR DISPLAY 6 1 Cleaning instructions To clean the display Clean the displ
25. automatically 5 21 5 Reset DICOM calibration About reset DICOM calibration It is possible to restore the original not corrected DICOM curve To reset the DICOM calibration 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Enter the DICOM preferences submenu 4 Select reset DICOM calibration to restore the original not corrected DICOM curve K5902079 CORONIS UNITI 19 12 2014 AAA 5 Advanced operation 5 21 6 DICOM error threshold About DICOM error threshold The threshold to define the DICOM compliance can be modified in steps of 5 starting from 5 to 30 When the maximum deviation is not bigger than the selected threshold the compliance check will be OK To set the DICOM error threshold 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Embedded QA menu 3 Enter the DICOM preferences submenu 4 Set DICOM error threshold as desired and confirm 5 22 Image scaling About image scaling Enabling image scaling will multiply each individual pixel to one or more adjacent pixels so that the size of the displayed image will be a multiple of the original image source video input signal gt Image scaling is only possible when the resolution of your displays video input signal is less than or equal to half the maximum resolution of the display To enable disable image scaling 1 Bring up the OSD main menu 2 Navigate
26. ay using a sponge cleaning cloth or soft tissue lightly moistened with a recognized clean ing product for medical equipment Read and follow all label instructions on the cleaning product In case of doubt about a certain cleaning product use plain water Do not use following products Alcohol solvents at higher concentration gt 5 Strong alkalis lye strong solvents Acid e Detergents with fluoride e Detergents with ammonia e Detergents with abrasives e Steel wool Sponge with abrasives Steel blades e Cloth with steel thread CAUTION Take care not to damage or scratch the front glass or LCD Be careful with rings or other jewelry and do not apply excessive pressure on the front glass or LCD CAUTION Do not apply or spray liquid directly to the display as excess liquid may cause damage to internal electronics Instead apply the liquid to a cleaning cloth K5902079 CORONIS UNITI 19 12 2014 AAA 6 Cleaning your display 46 K5902079 CORONIS UNITI 19 12 2014 7 Important information 7 IMPORTANT INFORMATION 7 1 Safety information General recommendations Read the safety and operating instructions before operating the device Retain safety and operating instructions for future reference Adhere to all warnings on the device and in the operating instructions manual Follow all instructions for operation and use Electrical Shock or Fire Hazard To prevent electric shock or fire hazard do
27. become available for the selected video input signal on each side of the display Expert mode This mode is intended for displaying and manually configuring one or two connected video input signals When selecting this mode the video settings become available for both video input signals on both sides of the display To select an image source selection mode 1 Bring up the OSD main menu 2 Navigate to the Configuration Image Sources menu 3 Enter the Image Source Selection submenu 4 Select one of the available image source selection modes and confirm 5 24 Grayscale conversion modes About grayscale conversion modes Grayscale conversion modes specify how color generated on the display controller is converted to grayscale in your display The available grayscale conversion modes are No Conversion Use Red Channel This mode is intended for grayscale displays where gray is sent over the red channel gray is sent over the green channel gray is sent over the blue channel To manually select a grayscale conversion mode 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Sources gt Input Settings gt DisplayPort1 2 menu 3 Enter the Grayscale Conversion submenu 4 Select one of the available color conversion modes and confirm 5 25 Input interface standard version About Input interface standard version The Coronis Uniti supports two input interface standard versions DPCD V1
28. cations 040000 00e n n nmn 56 7 8 Open source license information 00 00 ccc cece cece cece cece eee rnrn rrr rrr nnn 58 2 K5902079 CORONIS UNITI 19 12 2014 7 Welcome 1 WELCOME 1 1 About the product Overview Thank you for choosing this Coronis Uniti Coronis Uniti is an ingenious PACS display system designed to enhance flexibility and productivity in diag nostic imaging Featuring the industry s first 33 inch color LCD that can be used as two seamless heads or one wide screen display Coronis Uniti offers you the freedom to organize your workspace just the way you want it It allows you to read radiology mammography and breast tomosynthesis images side by side on a single diagnostic screen Coronis Uniti features Barco Optical Glass illuminated by DuraLight Brilliance to provide an exceptional image over your entire field of view Use the instructions in this guide to install your Coronis Uniti display and discover the productive features and included accessories CAUTION Read all the important safety information before installing and operating your Coronis Uniti Please refer to the dedicated chapter in this user guide 1 2 What s in the box Overview Your Coronis Uniti comes with e this Coronis Uniti user guide e Quick Installation Sheet a system CD two DisplayPort cables a USB cable asetof AC power cords an external power supply Fil
29. correction value for this reading room These parameters are stored in your display and determine the preset ambient light correction value to take into account to recalculate the DICOM display function when Ambient Light Compensation ALC is enabled Please refer to Ambient Light Compensation ALC page 36 to enable ALC K5902079 CORONIS UNITI 19 12 2014 5 Advanced operation The available reading rooms for your Coronis Uniti are CR DR MAMMO Corresponds to light conditions in diagnostic reading rooms for computed radiology digital radiology or mammography This setting has the lowest maximum ambient light CT MR NM Corresponds to light conditions in diagnostic rt rooms for computed tomography magnetic resonance or nuclear medicine scans Staff Office Corresponds to light conditions in office rooms Clinical Viewing Room Corresponds to light conditions in diagnostic reading rooms for clinical viewing Emergency Room Corresponds to light conditions in emergency rooms Operating Room Corresponds to light conditions in operating rooms This setting has the highest maximum ambient light To select a reading room 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Ambient Light menu 3 Enter the Reading Room submenu 4 Select one of the available reading rooms and confirm 5 20 Continuous ALC About Continuous ALC gt Continuous ALC can only be selected when the DICOM display f
30. d QA Medical QAWeb brings many benefits such as centralized asset management the ability to schedule tasks remote man agement automated reporting alerting and specific support of regional QA standards such as DIN 6868 57 JESRA and AAPM TG18 That s why MediCal QAWeb Agent acts as the master for all supported dis plays from the moment it is installed and running MediCal QAWeb Agent will take over from Embedded QA and overwrite any settings which were applied by Embedded QA 5 21 2 DICOM status report 38 About DICOM status report Following information is available since last compliance check is compliant or not Maximum error Shows the maximum error of the current DICOM curve This is the deviation compared to a perfect DICOM Error threshold Shows the error threshold This is LEE maximum error allowed before a DICOM calibration is required compliance check last compliance check function Ambient light compensation Shows the ambient light re D Compensation stats Reading Room hows the selected reading room luminance Shows the measured luminance Black luminance Shows the measured backlight luminance DICOM Calibration Status No calibration executed yet No other information is visible Calibration executed When the calibration is executed the following extra information is shown Backlight runtime elapsed since latest calibration display function ambient light compensation reading room K5902079 CORON
31. e following measures e Reorient or relocate the receiving antenna Increase the separation between the device and receiver Connect the device into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Canadian notice This ISM device complies with Canadian ICES 001 Cet appareil ISM est conforme la norme NMB 001 du Canada 7 4 EMC notice General information No specific requirement on the use of external cables or other accessories except power supply With the installation of the device use only the delivered power supply or a spare part provided by the legal manufacturer Using another can result in a decrease of the immunity level of the device Electromagnetic emissions The Coronis Uniti is intended for use in the electromagnetic environment specified below The customer or the user of the Coronis Uniti should assure that it is used in such an environment RER Electromagnetic environment Guidance RF emissions Group 1 The Coronis Uniti uses RF energy only for its internal function Eiern Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment CISPR 41 ae ne ee Mie Harmonic emissions Class D nepos OM eS G
32. e increments that are not optimal for crucial diagnostic information Studies have shown however that in medical images certain grayscale color parts contain more diagnostic information then others To respond to these conclusions display functions have been defined These functions emphasize on these parts containing crucial diag nostic information by correcting the native panel behavior not be corrected Dynamic Gamma 1 8 These are gamma functions that are shifted to take into account the non zero luminance of an LCD panel when driven with a black signal They are especially useful in CT applications to improve the perception of low Hounsfield values DICOM Digital Imaging and Communications Dynamic Gamma 2 2 in Medicine is an international standard that was developed to improve the quality and communication of digital images in radiology In short the DICOM display function results in more visible grayscales in the images Barco recommends selecting the DICOM display function for most medical viewing applications K5902079 CORONIS UNITI 19 12 2014 AS 5 Advanced operation User This display function will be automatically selected when display functions are defined by MediCal QAWeb Gamma 1 8 Select one of these display functions in case the display is to replace a CRT display with a gamma Samma AA of 1 8 or 2 2 respectively To select a display function 1 Bring up the OSD main menu 2 Navigate to the Confi
33. e used in displaying and viewing digital images including standard and multi frame digital mammography for review analysis and diagnosis by trained medical practitioners It is especially designed for breast tomosynthesis applications Caution USA Federal law restricts this device to sale by or on the order of a physician or a practitioner trained on its use FCC class B This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference re ceived including interference that may cause undesired operation K5902079 CORONIS UNITI 19 12 2014 7 Important information This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This device generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception which can be determined by turning the device off and on the user is encouraged to try to correct the interference by one or more of th
34. ece ents and those directly connected to IEC 61000 3 2 _ l l the public low voltage power Voltage fluctuations flicker Complies supply network that supplies EMISSIONS buildings used for domestic IEC 61000 3 3 purposes This Coronis Uniti complies with appropriate medical EMC standards on emissions to and interference from surrounding equipment Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interfer ence that may cause undesired operation Interference can be determined by turning the equipment off and on K5902079 CORONIS UNITI 19 12 2014 ___ 81 7 Important information If this equipment does cause harmful interference to or suffer from harmful interference of surrounding equipment the user is encouraged to try to correct the interference by one or more of the following mea sures e Reorient or relocate the receiving antenna or equipment Increase the separation between the equipment and receiver Connectthe equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced technician for help Electromagnetic immunity The Coronis Uniti is intended for use in the electromagnetic environment specified below The customer or the user of the Coronis Uniti should assure that it is used in such an environment Immunity test IEC
35. er of the communications equipment Rated maximum output Separation distance according to frequency of transmitter power of transmitter 150kHz to 80MHz 80MHz to 800MHz 800MHz to 2 5GHz d 2 3 P 0 12 0 23 0 73 2 3 7 3 23 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies These guidelines may not apply in all situations Electromagnetic propagation is af fected by absorption and reflection form structures object and people 7 5 Explanation of symbols Symbols on the device On the device or power supply you may find the following symbols nonrestrictive list C Indicates compliance with the Directive 93 42 EEC as Class device C Indicates compliance with the Directive 93 42 EEC as Class Il device 0120 FE Indicates compliance with Part 15 of the FCC rules Class A or Class B Ae Indicates the device is approved according to the UL regulations 5 For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter Where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer 54 DD K5902079 CORONIS UNITI 19 12 2014 7 Important information Indicates the device is approved according to the UL regulations for Canada and US Se S S BWDLEADAGeOS e 5 Indica
36. ese s s ss nn rne 38 5 21 3 DICOM compliance check ssssssssssssssssssssssssssssss esse s s nnn 39 5 21 4 DICOM calibration II mee m e ss n rna 39 5 21 5 Reset DICOM calibration oooooccccccccccccccccccncnonnnonnnnnn cnn eee eee s s nnn 39 5 21 60 DICOM error threshold uoa beret a e da s NR ea 40 5 22 Image scallng i oe AAA AA Fe aaa dudo EE ERI dd 40 5 23 Image source selection modes 4 444 sedes n eh haha aeneae gea nenne 40 5 24 Grayscale conversion modes meses 41 5 25 Input interface standard version 41 5 20 EDID format irae Ee aduana eter EORR EDU Ue MR a dada dete ER edd 42 9 21 EDID timiNGS 4 is eo A A AAAA RE ia beets M TAE 42 9 28 Display EUER 42 9 29 Display status isis A AAA A AAA A ARA 43 6 Cleaning your display niii eaae e A presen uova 45 6 1 Cleaning instructions 5 5 c eor andre ARR ij e pni dra 45 7 Important information it eR ue RE SRFUEEEERARERARUNUETUECOUUUUE RERUM A 47 ASA A E AE RT hae 47 7 2 Environmental information sssssssssssssssssssssssssssssss sss ss s nnn 48 7 3 Regulatory compliance information sss m nnn 50 A EMGAOGe SAR SAR RTS AA A A ARE PIE 51 4 57 Explanation of symbols ute obi AA A A 54 1 0 Legal disclaimer d ma pA oS see A S Ge QUI ER 56 7 7 Technical specifi
37. g and the tilt system in the display stand are locked with red pins to prevent damage during transportation You ll have to remove both pins before adjusting your display position To adjust the display position 1 Remove the tilt lock pin see Unlocking the tilt mechanism page 10 2 Remove the height lock pin in the display stand see Unlocking the height mechanism page 10 3 Tilt swivel raise and lower the display as desired K5902079 CORONIS UNITI 19 12 2014 A 3 Display installation CAUTION Do not try to pivot your display when attached to the stand Trying to do so could cause serious damage to your display and its stand 3 5 Connecting the signal cables To get access to the connectors remove the connector compartment cover See Re moving the connector compartment cover page 9 To connect the signal cables to the display 1 Connect one head of the display controller to the DisplayPort connector with one of the supplied Dis playPort cables 172 OOO K5902079 CORONIS UNITI 19 12 2014 3 Display installation 2 Connect another head of the display controller to the other DisplayPort connector with one of the sup plied DisplayPort cables 3 Connect a PC USB downstream connector to the display s USB upstream connector by means of the supplied USB 2 0 cable K5902079 CORONIS UNITI 19 12 2014 13 3 Display installation s Communication with the display is possible via DisplayPort
38. g with the same image or an application with static image elements for several hours continuously so that the screen saver is not activated change the image content regularly to avoid image retention of the static elements Understand pixel technology LCD displays use technology based on pixels As a normal tolerance in the manufacturing of the LCD a limited number of these pixels may remain either dark or permanently lit without affecting the diagnostic performance of the product To ensure optimal product quality Barco applies strict selection criteria for its LCD panels To learn more about LCD technology and missing pixels consult the dedicated white papers available at www barco com healthcare Enhance user comfort Every Barco multi head display system is color matched with the highest specifications in the market tant to use all displays of a multi head configuration at the same rate to preserve color Barco recommends keeping color matched displays together Furthermore it is impor Cg matching throughout the economic lifetime of the system K5902079 CORONIS UNITI 19 12 2014 AAA 4 Daily operation Maximize quality assurance The MediCal QAWeb system offers online service for high grade Quality Assurance providing maximum diagnostic confidence and uptime Barco recommends to install MediCal QAWeb Agent and apply the default QAWeb policy at least This policy includes calibration on regular intervals Connecting to
39. gher frequency range applies These guidelines may not apply in all situations Electromagnetic propagation is af e fected by absorption and reflection from structures objects and people 3 Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the Coronis Uniti is used exceeds the applicable RF compliance level above the Coronis Uniti should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as re orienting or relocating the Coronis Uniti 4 Over the frequency range 150 kHz to 80 MHz field strengths should be less than 3 V m K5902079 CORONIS UNITI 19 12 2014 __ 5B 7 Important information Recommended separation distance The Coronis Uniti is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer of the user of the Coronis Uniti can help prevent electromagnetic interfer ence by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the Coronis Uniti as recommended below according to the maximum output pow
40. guration gt Calibration menu 3 Enter the Display Function submenu 4 Select one of the available display functions and confirm 5 18 Ambient Light Compensation ALC About ALC Ambient Light Compensation ALC can only be enabled on your display when the DI COM display function is selected Therefore please refer to Display functions page 35 to correctly set the display function When ALC is enabled the DICOM display function will be recalculated taking a preset ambient light cor rection value into account This value is determined by the selected reading room Therefore it is also important to select a realistic reading room when enabling ALC This can be done by following the instruc tions in Reading rooms page 36 To enable disable ALC 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Ambient Light menu 3 Enter the Ambient Light Compensation submenu 4 Select Enabled Disabled as desired and confirm 5 19 Reading rooms 36 About reading rooms X Reading rooms can only be selected when the DICOM display function is selected Therefore please refer to Display functions page 35 to correctly set the display function The American Association of Physicists in Medicine AAPM composed a list of pre defined reading rooms Each of these reading rooms are defined by following parameters the maximum light allowed in this type of room the preset ambient light
41. ht key Behavior No Push Push Enable OSD Right key Menu Behavior No push Push No menu EL M SoftGlow modes between task light wall light both none Push Nothing a Push No menu Cycle viewing mode between text and diagnostic No push No push Menu Enter the OSD menu 4 7 l Luminate About I Luminate When the display is in power on mode and the OSD menu is not shown I Luminate can be activated by touching the I luminate left key When touching the I Luminate key the display will enter the I Luminate mode for approximately 1 minute Touch the I Luminate key again to immediately switch back to normal mode 4 8 Extended display keypad functions About extended display keypad functions The concept of the extended display keypad functions is to present a selection of functions immediately available to the user without the need to navigate through the OSD Menu x The extended display keypad functions will only be available when no OSD menu is visible on the screen 4 8 1 l luminate mode To quickly change the I luminate mode 1 While no OSD menu is on the screen press the l luminate Left key to bring up the I luminate quick selection menu 2 Toggle the available l luminate modes see I Luminate default mode page 32 by pressing the Right key 4 8 2 Viewing mode To quickly change the viewing mode 1 While no OSD menu is on the screen press the Left key and Right key simultaneously to change the view
42. iew around the display s The SpotView vanishes when no finger is pressing on the MultiTouchPad unless the left side of the MultiTouchPad button is held down 16 OOO K5902079 CORONIS UNITI 19 12 2014 3 Display installation 3 9 Routing the cables amp Reattach the connector compartment cover To route the cables 1 Route all connected cables through the cable routing channel in the stand of your display Tip The cable straps at the inside of the connector compartment allow you to fix the cables for better shielding of the cables To reattach the connector compartment cover 1 Reattach the connector compartment cover by sliding the cover s top You ll hear a click sound of the cover s clips when the connector compartment cover is in position K5902079 CORONIS UNITI 19 12 2074 17 3 Display installation 3 10 Fixation of the foot on the desk Overview If you would like to attach the Coronis Uniti to a desk the tilt amp swivel foot has 4 screw holes 4x M4 to mount the foot on a desk 48 K5902079 CORONIS UNITI 19 12 2014 3 Display installation 1 Drill four holes in the desk 143 sl 120 Fixation position 4x M4 100 300 100
43. ing mode 2 Toggle the available viewing modes see Viewing modes page 34 by pressing the Left Right key simultaneously K5902079 CORONIS UNITI 19 12 2014 IO 27 4 Dally operation 28 K5902079 CORONIS UNITI 19 12 2014 5 Advanced operation 9 ADVANCED OPERATION 5 1 OSD menu language About the OSD menu language By default the OSD menu comes up in English However there s a wide range of other languages avail able for the OSD menu of your Coronis Uniti To change the language of the OSD menu 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Menu menu 3 Enter the Language submenu 4 Select one of the available languages and confirm 5 2 OSD menu automatic close function About the OSD menu automatic close function By default the OSD menu will disappear automatically after approximately 90 seconds of inactivity How ever this function can be disabled so that the OSD menu remains on the screen until manually closed To enable disable the OSD menu automatic close function 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Menu menu 3 Enter the Automatic Close submenu 4 Select Enabled Disabled as desired and confirm 5 3 Power status indicator light About the power status indicator light By default when the display is switched on the power status indicator light is dimmed This behavior can be changed so that
44. ing the User color temperature setting you will be able to manually define the X and Y coordinates or the display color temperature in separate submenus Native White The native unmodified color temperature of the LCD panel To select a color preset 1 Bring up the OSD main menu 2 Navigate to the Configuration Calibration Color Settings menu K5902079 CORONIS UNITI 19 12 2014 AAA 5 Advanced operation 3 Enter the Color Presets submenu 4 Select one of the available Color Presets and confirm 5 14 Color temperature About color temperature It is possible to change the color temperature of your display Color temperature can only be changed on your display when color presets is set to user Therefore please refer to Color presets page 33 to do this To change the color temperature 1 Bring up the OSD main menu 2 Navigate to the Configuration Calibration Color Settings menu 3 Enter the Color Definition submenu 4 Select Color Temperature and confirm 5 Enter the Color Temperature submenu 6 Set the Temperature value as desired and confirm 5 15 Color coordinates About color coordinates It is possible to change the color coordinates of your display Color coordinates can only be changed on your display when color presets is set to user Therefore please refer to Color presets page 33 to do this To change the color coordinates 1 Bring up the OSD main menu 2
45. m clip e MultiTouchPad If you ordered a Barco display controller it s also in the box together with its accessories A dedicated user guide is available on the system CD Keep your original packaging It is designed for this display and is the ideal protection during transport and storage K5902079 CORONIS UNITI 19 12 2014 AAA 7 Welcome 4 OOOO K5902079 CORONIS UNITI 19 12 2014 2 Parts controls and connectors 2 PARTS CONTROLS AND CONNECTORS 2 1 Display front view Overview COOCOO Image 2 1 Front view Luminate Left key O Right key Q Menu key Q Standby key Power status indicator light Power On Q Power status indicator light Standby Q Guard Q Ambient light sensor K5902079 CORONIS UNITI 19 12 2014 AAA 2 Parts controls and connectors 2 2 Display rear view Connector compartment cover closed Image 2 2 Rear view with closed connector compartment cover Connector compartment cover Tilt lock pin only for transportation Q Tilt amp swivel foot Q Cable duct Foot lock pin only for transportation Q SoftGlow Task light Q SoftGlow Wall light Store the foot lock pin and tilt lock pin for possible future transportation of the display 6 z OOO K5902079 CORONIS UNITI 19 12 2014 2 Parts controls and connectors Connector compartment cover open Image 2 3 Rear view with open connector compartment cover Power connector Display port connector Display port connector
46. nded for continuous operation Transient over voltage If the device is not used for a long time disconnect it from the AC inlet to avoid damage by transient over voltage K5902079 CORONIS UNITI 19 12 2014 __ A7 7 Important information To fully disengage the power to the device please disconnect the power cord from the AC inlet Power cords Do not overload wall outlets and extension cords as this may result in fire or electric shock Mains lead protection U S Power cord Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them paying particular attention to cords at plugs and receptacles e The power supply cord should be replaced by the designated operator only at all time Usea power cord that matches the voltage of the power outlet which has been approved and complies with the safety standard of your particular country Water and moisture Never expose the device to rain or moisture Never use the device near water e g near a bathtub washbasin swimming pool kitchen sink laundry tub or in a wet basement Ventilation Do not cover or block any ventilation openings in the cover of the set When installing the device in a cupboard or another closed location heed the necessary space between the set and the sides of the cupboard Installation Place the device on a flat solid and stable surface that can support the weight of at least 3 devices
47. position About the I Luminate film position By default the I Luminate rectangle comes up in the top center of the left part of the screen This position can be changed to top left or top right corner of the left part of the screen or top left top center or top right corner of the right part of the screen To set the I Luminate film position 1 Bring up the OSD main menu 2 Navigate to the Configuration gt I Luminate menu 3 Enter the Film Position submenu 4 Select Left Side Top Left Center Right or Right Side Top Left Center Right as desired and confirm 5 12 Luminance target About the luminance target The luminance target of your Coronis Uniti is adjustable over a predefined range When you change the luminance target the display will adjust its backlight to reach the target To set the luminance target 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration menu 3 Enter the Luminance Target submenu 4 Set a luminance target value as desired and confirm The default factory DICOM calibrated luminance value is available in the technical spec ifications table The guaranteed backlight lifetime is valid for this setting 5 13 Color presets About color presets The available color preset settings for your display are Clearbase Simulation of the clearbase film color temperature Bluebase Simulation of the bluebase film color temperature User When select
48. range indicator light and the white indicator light are lit until the unit is fully started K5902079 CORONIS UNITI 19 12 2014 4 Daily operation To switch your display to Stand by using the keys Switching off the display can be done by 1 Push the standby key shortly for three times After the second push the OSD message Power off appears on the display this means the display will go in standby mode As a result the display will switch to stand by mode and the power status indicator light is orange In case of a power outage recovery your display will always start up in the power mode it was in before the power interruption i e stand by or on This protects your display against inadvertent image retention problems 4 4 Bringing up the OSD menus How to bring up the OSD menus The OSD menu allows you to configure different settings to make your Coronis Uniti fit your needs within your working environment Also you can retrieve general information about your display and its current configuration settings through the OSD menu Bringing up the OSD menus can be done by 1 If not already done so switch on the display as previously described 2 Illuminate the keys as previously described 3 While the keys are illuminated touch the menu key As a result the OSD main menu comes up in the bottom right corner of the screen However if no further actions are taken within the following 90 seconds the OSD will disappe
49. rate when first time starting up If you are using a Barco display controller please consult the dedicated user guide available on the system CD to install the drivers software and documentation When this is done your display will automatically detect the connected video input signal s and apply the correct video mode and refresh rate 22 DD K5902079 CORONIS UNITI 19 12 2014 4 Daily operation 4 DAILY OPERATION 4 1 Recommendations for daily operation Optimize the lifetime of your display Enabling the Display Power Management System DPMS of your display will optimize its diagnostic life time by automatically switching off the backlight when the display is not used for a specified period of time By default DPMS is enabled on your display but it also needs to be activated on your workstation To do this go to Power Options Properties in the Control Panel Barco recommends setting DPMS activation after 20 minutes of non usage Cg Use a screen saver to avoid image retention Prolonged operation of an LCD with the same content on the same screen area may result in a form of image retention You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver You can activate a screen saver in the Display properties window of your workstation Barco recommends setting screen saver activation after 5 minutes of non usage A good screen saver displays moving content In case you are workin
50. ration gt User Interface gt Controls menu 3 Enter the Power Lock submenu 4 Select Enabled Disabled as desired and confirm 5 6 SoftGlow Task light 30 About the SoftGlow Task light The Coronis Uniti is equipped with a SoftGlow Task light This allows you to have light on your desk in a dark environment The brightness of the SoftGlow Task light can be adjusted To enable disable the SoftGlow Task light 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Lights menu 3 Enter the SoftGlow Task light submenu 4 Select Enabled Disabled as desired and confirm To adjust the SoftGlow Task light brightness 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Lights menu 3 Enter the SoftGlow Task light brightness submenu 4 Set a SoftGlow Task light brightness value as desired and confirm K5902079 CORONIS UNITI 19 12 2014 5 Advanced operation 5 7 SoftGlow Wall light About the SoftGlow Wall light The Coronis Uniti is equipped with a SoftGlow Wall light This allows you to have light on the wall at the back of your display in a dark environment The brightness of the SoftGlow Wall light can be adjusted To enable disable the SoftGlow Wall light 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Lights menu 3 Enter the SoftGlow Wall light submenu 4 Select Enabled Disabled as desired and confirm To adjust the SoftGlow Wall light brightness 1
51. s from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources For more information about recycling of this product please contact your local city office or your municipal waste disposal service For details please visit the Barco website at http www barco com en AboutBarco weee Turkey RoHS compliance A mmmgm T rkiye Cumhuriyeti AEEE Y netmeli ine Uygundur Republic of Turkey In conformity with the WEEE Regulation HE X hi RoHS Chinese Mainland RoHS FRE h ES Ri BFS BT 75 RET bI BED KX th ERO PENA RE ROHS LAR EB 3 tH Y Barco mm PARED BL ERU LES is JR B n MNAE HEA RE ROHS fR 4 815 E EE AP Ml MCV EHE RJ inr EET BRI GR H According to the China Administration on Control of Pollution Caused by Electronic Information Products Also called RoHS of Chinese Mainland the table below lists the names and contents of toxic and or hazardous substances that Barco s product may contain The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China in the section Limit Requirements of toxic substances in Electronic Information Products FANA 4 F LET Ep Component name Hazardous substances and elements 4h FR E FINE cd SRA Pb Hg Cd Cr6 gi Printed Circuit Assemblies T oe HA a LCD panel Bi Internal wiring pudia Lp po Heatsinks a NEN HE Fan es P LL po Metal enclosure ace us K5902079 C
52. tes the device is approved according to the UL Demko regulations Indicates the device is approved according to the CCC regulations Indicates the device is approved according to the VCCI regulations Indicates the device is approved according to the KC regulations Indicates the device is approved according to the BSMI regulations Indicates the device is approved according to the PSE regulations Indicates the USB connectors on the device Indicates the DisplayPort connectors on the device Indicates the manufacturing date Indicates the temperature limitations for the device to safely operate within specs x x e b Indicates the device serial no Warning dangerous voltage Caution Consult the operating instructions IE E 6 Values for xx and yy can be found in the technical specifications paragraph K5902079 CORONIS UNITI 19 12 2014 AAA 7 Important information Indicates this device must not be thrown in the trash but must be recycled according to the European WEEE Waste Electrical and Electronic Equipment directive E Indicates Direct Current DC Indicates Alternating Current AC Stand by E Equipotentiality 7 6 Legal disclaimer Disclaimer notice Although every attempt has been made to achieve technical accuracy in this document we assume no responsibility for errors that may be found Our goal is to provide you with the most accurate and usable documentation possible if you
53. the cables amp Reattach the connector compartment cover 17 3 10 Fixation of the foot on the desk Hmmm 18 3 11 VESA mount installation ssec Ree esee te Pe vea re xe A 19 3 12 First time Starting UP ioo 2708 rete enr Pad nana ie troi Dose esta dede ad 22 4 Daily ipi mem 23 4 1 Recommendations for daily operation 0 cece cece eee eee nes 23 4 2 Key indicator lights 2 xiii boites tbt beo M Pts lement ev Eo P en te Id 24 4 3 Standby Switching eisir iiit a EEEN EAEI EEEE AREE ERE ELA MIU 24 44 Bringing up the OSD menus iii ee gh hh eus d ru aka rh EE EX RR a ga rh e EY a des 25 4 5 Navigating through the OSD menus 0 cece cece ene meer 25 4 6 Overview of the functionality of the Left Right keys 26 47 ERI CMM H 27 4 8 Extended display keypad functions emen 27 4 8 1 Iduminate mode oie th dE bee idad 27 4 8 2 Viewing mode aetan E diete Mia QUERER is rt Abe LL QUEE REGERE E inne dus 27 5 Advanced operation Er A Ge ae mn Ee 29 5 14 OSD menu language ceu llllkiiglii s nee ea eee eee Se e iei lee den ee nee dua 29 5 2 OSD menu automatic close function n nar rnnn nn rr rra 29 5 3 Power status indicator light licere erede e
54. through the customer section of the Barco website or through other online means K5902079 CORONIS UNITI 19 12 2014
55. to the Configuration gt Image Source menu 3 Enter the Scaling submenu 4 Select Enabled Disabled as desired and confirm 5 23 Image source selection modes 40 About image source selection modes Your Coronis Uniti automatically detects the number of video input signals connected attaches them to the correct display side and applies the correct video settings to it resolution video encoding mode refresh rate However it may be needed to manually select the video input signal s to be displayed on a certain display side or to adjust certain video settings yourself The start to this is selecting one of the following image source selection modes available for your display Automatic In this mode your display automatically detects the connected video input signals attaches them to the correct display side and applies the correct video settings to it resolution video encoding mode refresh rate No video settings are available when this mode is selected One Image Source This mode is intended for displaying and manually configuring only one connected video input signal When selecting this mode the video settings become available for the selected video input signal K5902079 CORONIS UNITI 19 12 2014 5 Advanced operation Two Image Sources This mode is intended for displaying and manually configuring two connected video input signals one on each display side When selecting this mode the video settings
56. unction is selected Therefore please refer to Display functions page 35 to correctly set the display func tion Enabling continuous ALC will continuously recalculate the DICOM display function taking the averaged ambient light into account To select continuous ALC 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Ambient Light menu 3 Enter the Continuous ALC submenu 4 Select Enabled Disabled as desired and confirm 5 21 Embedded QA Overview About Embedded QA DICOM status report DICOM compliance check DICOM calibration Reset DICOM calibration K5902079 CORONIS UNITI 19 12 2014 __ 87 5 Advanced operation DICOM error threshold 5 21 1 About Embedded QA About Embedded QA allows you to run a display calibration or compliance test directly from the display using the OSD menus described in the next sections Embedded QA will use the front sensor I Guard to measure the necessary luminance levels for either a calibration or compliance test Various settings for both actions can be selected from the display s OSD menu The last results of both actions can be consulted from the OSD Embedded QA or MediCal QAWeb Embedded QA is not a replacement for the Barco MediCal QAWeb solution Although Embedded QA is a reliable option to perform a simple calibration or compliance test Barco still highly recommends MediCal QAWeb as the solution of choice for calibration an

3. display installation - CNET Content Solutions

Contents

Download Pdf Manuals

Related Search

Related Contents