Home

Untitled

1. Base Base Should be checked after completion is the height of the shoulder belt appropriate for the infant safety seat Are the fastening plate and the buckle of the car firmly locked Is there any twisting in the waist belt of the car s the seat belt of the car adjusted enough to be strongly tight Is the shoulder belt of the car securely locked inside the set clip After checking the items shown above The main body fastened to the seat belt of the car needs to be shaken to see if the safety seats bottom is shaken within about 3cm aw if the shaking range is larger than 3cm the safety seat needs to be reinstalled again according to the installation procedure 16 How to install gt Forward Facing In the driving direction Front viewing Applicable Weight Below 9kg 18kg Fasten by using the car s 3 point seat belt 4 Danger A Warning A Warning Warning 6 Advice Tightly Belt passage Base The product should not be used for the seats with an airbag When activated the airbag may cause the infant to risk his or her life or suffer serious damage When the infant safety seat is installed on the passenger s seat it may cause some inconvenience in operating the transmission gear or the side brake When such inconvenience arises you need to refrain from using the product for the passenger s seat and rather use it for the back seats
2. The product should not be used for the seats with an airbag When activated the airbag may cause the infant to risk his or her life or suffer serious damage Be careful not to allow the infant to push the press button of the front pad The fastening plate needs to be checked for any loosening frequently When the plate is loosened the infant may risk his or her life or suffer critical damage when a crash or an abrupt stopping occurs If the product suffers any crash or a strong impact it should not be used again regardless of damage to its surface The safety seat may not function as originally designed when a situation occurs consequently causing the infant to risk his or her life or suffer serious damage Using the safety seat without using the seat belt should not be allowed The safety seat may not function as originally designed when a situation occurs consequently causing the infant to risk his or her life or suffer serious damage A guardian should get on the vehicle together considering that the infant may get caught in the belt on the neck or be placed in a dangerous situation due to his or her various motions When the infant safety seat is installed on the passenger s seat it may cause some interference leading to inconvenience in operating the transmission gear or the side brake When such inconvenience arises you need to refrain from using the product for the passenger s seat and rathe
3. A DAIICHI Carseat Manual Infant protection device for a car For the safety in using it Illustration of the indicative marks x 1 Usage conditions applicable for infants 1 About the seat to which the safety seat will be attached 2 About the seats to which the safety seat can not be attached 2 O O O A O OE A VR 3 5 Name of parts 6 How to operate Buckle releasing and locking Fees UNS Ne DU SR Ne se eee How to use the angle adjusting EVE oer sina kn ne OE AE narek kah 8 How to use the locking lev r a A 9 e Before being fastened into the car How to seat an infant CEECEE ONE AN anya Bua a aww Reese nbs Bea Rea Tae eh MRE a a 1 0 Height adjustment of the shoulder belt _ 1 1 Height adjustment of the head seat o 1 2 How to fasten the seat into the car Types of the car s seat belts to which the safety seat 13 can be attached Decision on the direction of the installation 13 Rearward Facing installation method Forward Facing installation method How to remove the seat cover How to use the shoulder pad exclusive for children e ISOFIX method Safety Information Before installing or using the product it is necessary to read these instructions carefully because only a corr
4. When such inconvenience continues it may interfere with operating the transmission gear or the side brake leading to a highly risky situation When installed onto the front seat the infant safety seat may block the rear vision of the door mirror of the car In that case the safety seat needs to be installed onto other seats When there is a passenger in the back seat the safety seat should not be attached to the passenger seat of a 2 door or 3 door vehicle or the secondary seat near the access area for ascending and descending in case of the one box type vehicle or a mini van in order to secure the emergency exit When you operate the locking lever you should be careful not to get your hands or fingers caught The backrest needs to be made upright e Foreasier attachment the car s front seat needs to be pushed backwards Adjust the height of the shoulder strap and headrest appropriately to infant s body See the shoulder strap and headrest adjustment on page 11 amp 12 The main body needs to be placed in the Forward facing position in the driving direction Angle adjusting lever 17 4 Shoulder belt of a car You need to make the seat belt of the car come out by pulling it Danger The attachment and fastening methods may vary depending on the kinds of the seat belt of a car Refer to Types of the Car s Seat Belts to Which the Safety Seat Can Be Attached on page 12 to fasten the infant safety seat corre
5. While operating the locking lever you should be careful not to get your hands or fingers caught in it Insert the car shoulder strap through the locking lever and slide the lever to the opposite side to lock it while pulling the strap tightly Position the strap under the lever and push the lever all the way to securely Slide the locking lever sideway to unlock hold the strap Vehicle shoulder belt 3 In case of the rearward facing mode only As indicated above fix the belt with the locking lever and hang it to the belt guide while pulling it tightly Belt guide Releasing Release the car buckle Slide the locking lever to unlock 9 and release the car shoulder strap Before being attached into the car Each part needs to be adjusted to be suitable for the body of the infant before being attached into the car Every time when an infant is seated the adjusting belt should be pulled to seat the baby tightly If the shoulder 4 Danger belt can not function as originally designed consequently the infant may risk his or her life or suffering critical damage The buckle of the front pad needs to be released first After the infant is seated the shoulder belt the the belt adjusting lever needs to be finger pressed needs to be put on At that time the height of while pulling and loosening the shoulder belt Refer to the shoulder belt needs to be adjusted to fit the Buckle Releasing and Lockin
6. the infant may be loosened from the car or hit the glass for example during the crash or the abrupt stopping risking his or her life or suffering serious damage If the safety seat can not be attached according to the user manual depending on the kinds of the seat belt of a car and the types of the seat the safety seat needs to be attached to other seats If the safety seat is not attached appropriately according to the user manual the infant may risk his or her life or suffering serious damage during the crash or the abrupt stopping Every time the infant is seated the adjusting belt should be pulled to seat the baby tightly If the shoulder belt can not function as originally designed the infant may risk his or her life or suffering critical damage The belt cover should be attached for use If the belt cover can not function as originally designed the infant may risk his or her life or suffering critical damage If the infant safety seat is exposed to direct sunlight for long hours metal and PVC parts may get heated The guardian needs to check it before seating the infant In summer or when sunlight is strong the car needs to be parked ina shady lot or a towel for example can be used for coverage An infant should not be left alone in a car At noon the temperature in side a car can rise causing the infant to suffer dehydration consequently risk his or her life or suffer serious damage
7. and down The headrest can be adjusted to 4 positions 2 The bottom of the headrest should be aligned close to infant s shoulders M Caution The position of the headrest must be adjusted appropriately to infant s body If failed to do so the safety seat may not deliver sufficient effects How to Finish Back Covering Roll the flipped edge of the covering inward Flip up the top edge of the backrest covering when adjusting the headrest from the 3rd position Finished covering Slide the covering into the space between the backrest and headrest to neatly finish the covering 12 How to attach the seat into the car First of all the types of the car seat belt need to be checked This equipment can be used for the 3 point seats that do not have a recoiling device or have a seat belt fitted with a recoiling device This equipment can not be attached for the 2 point seat belts There are different seat belts for different vehicle models Their features are different and the installing methods are also various In order to use the infant safety seat correctly and safely the safety seat needs to be fastened in a way suitable for your vehicle Seat belt Features Caution when installing the product Installation E L R AL R Normally the belt functions as an ELR belt The infant safety seat needs to be fastened When it is pulled to the end it will shift to the firmly and the belt needs to be p
8. ar e ls the seat belt of the car adjusted enough to be strongly tight e Is the shoulder belt of the car securely locked inside the locking lever After checking the items shown above The main body fastened to the seat belt of the car needs to be shaken to see if the safety seat s bottom is shaken within about 3cm ed If the shaking range is larger than 3cm the safety seat needs to be reinstalled again according to the installation procedure 1 5 19 How to remove the seat cover Wamina The front pad and the main body should not be 9 disassembled It may cause malfunctioning Follow the direction conversely when covering the seat Belt cover Remove back covering by detaching velcro on the back of the covering Remove the back covering from the bottom am se AAO SATO Sle CEE BS SAN SAONE MESNA BELI Main body After the belt cover at the back side of the main body is removed the shoulder belt needs to be taken off from the shoulder belt hanger The removed belt needs to be taken out through the shoulder belt hole The shoulder pad and the fastening plate need to be taken out from the shoulder belt Z For your information When the shoulder belt hanger can not be seen It is because the shoulder hanger is pushed inside In that case while you push up the shoulder belt adjusting lever Refer to Page 10 and Page 11 you need to extend the shoulder belt Then the shoul
9. cked The safety seat can not be fastened firmly The seat belt will be put on automatically Fully automatic when the front seat is taken and the door is seat belt closed When the door is opened the seat belt will be removed automatically 2 point seat belt Seat belt without a recoiling device The safety seat can not be fastened firmly Manual Others All kinds of seat belts not described in the table The safety seat can not be fastened firmly The infant safety seat should not be used when it can not be installed firmly according the kinds of the Danger seat belt of a car and the types of the seat If the safety seat is attached in appropriately the infant may risk his or her life or suffer serious damage during the crash or the abrupt stopping Decision on the direction of the installation Driving direction The direction of the installation needs to be decided according to the weight of the infant Installation in a Rearward facing mode Refer to Page 14 Below 13kg Height Up to 75cm Newborn 12 months Infant s weight height age range Installation in a Forward facing mode Refer to Page 17 Below 13kg 18kg Height Up to 75cm 100cm Newborn 12 months 13 How to install 1 Rearward Facing Newborn babies 12 months old Fasten by using the 3 point seat belt for a car Danger A Warning The shoulder belt needs not to be rolled i up more t
10. ctly The detached seat belt and fastening plate of a car need to be put through the belt passage along the backside of the main body Caution Be careful not to cause the waist belt of the car to be twisted Belt passage The detached waist belt of the car needs to be put through the belt passage The fastening plate of the car needs to be inserted into the buckle of the car A Caution Be careful not to cause the waist belt of the car to be twisted Waist belt of the car 1 Slide the locking lever on the other end of the vehicle mounting plate sideway to unlock 2 Insert the car shoulder strap through the locking lever and slide the lever to the opposite side to lock it while pulling the strap tightly Position the strap under the lever and push the lever all the way to securely hold the strap Z Caution The waist belt of the car needs to be pulled as much as possible to fasten it firmly without any shaking 18 5 Check the car shoulder strap is properly inserted through the locking lever If the car seat is shaking slide the locking lever sideway and press down to lock it while pulling the strap tightly using your body weight from above the car seat X Should be checked after completion e Is the height of the shoulder belt appropriate for the infant safety seat e Are the fastening plate and the buckle of the car firmly locked e Is there any twisting in the waist belt of the c
11. der belt hanger at the back side will come up to be seen 2 Pull out the shoulder strap and untie the elastic on the back of the head covering to remove The button of the adjusting belt needs to be removed and the seat Clip of the seat cover needs to be taken off Seat cover Belt guide Spread the covering left and right to get around the belt guide je bal o seu a A How to use the shoulder pad exclusive for children Shoulder pad for children is used for front facing installation over 9kg Detach existing shoulder pad Pull out the shoulder strap through a shoulder strap adjusting gear on the back of the car seat See P 11 Pull out the shoulder strap from the shoulder pad v 1111 non ye after measuring the optimal height for the shoulder of a child by seating him or her on the seat Refer to the following pictures Installation needs to be done by setting the shoulder belt at the same height of the shoulder of a child or higher Outer side The stitched side D It can be put through smoothly when being inserted using the folded part as shown in the dotted circle Advice f f The shoulder pad has an inner side Warning The installation needs to be made in a way that the rubber and an outer side side should be placed tightly against the infant The front si de of the shoulder pad N Caution The both shoulder pads right and left should be adjusted ee nie In
12. e reverse side has in the same height Front Back Outer In Side Side 21 TA The shoulder belt needs to be inserted The shoulder belt of the infant safety seat inserted through the shoulder pad with the shoulder pad needs to be inserted into the shoulder belt hole at the backrest D When the shoulder belt is pushed in slowly using a thumb Advice After the shoulder belt is inserted into the shoulder belt hanger the belt at the back side of the main body needs to be inserted A Caution The shoulder belt or the adjusting belt needs to be installed into the shoulder belt in a way that no twisting occurs ___ After the infant is seated onto the seat the adjusting belt should be pulled to position the Waring infant tightly by referring to lt How to Seat an Infant gt on page 10 The shoulder belt may loose the original function in a situation causing people to risk their ives or suffer serious damage A Waming The belt cover should be inserted for use The shoulder belt may loose the original function in a situation causing people to risk their lives or suffer serious damage Completion diagram Outer side gi 22 Inner side ISOFIX Installation Optional D This device can be used in vehicles designed to fit ISOFIX ISOFIX is an international standard fastener for child safety equipment installation for a vehicle that securely Adice protects infants through the direct connectio
13. edct installation and use quarantees an efficient protection Do not use the product for the infants not qualified for the usage conditions and for the seats that do not allow its installation A Danger If not followed in case of crash or abrupt stopping infants may get bounced out of the car or their heads may hit the glass risking their lives or suffering serious damage Illustration of the indicative marks The marks below illustrate some instructions for you to follow in particular for the safety in using the product They are relating to safety so you should follow them A Danger If you do not follow you may risk your life or suffer critical damage A Warning If you do not follow you may suffer critical damage A Caution If you do not follow you may suffer damage or an accident K E The items that must be checked for safety are described amp Caution Basic knowledge for using the product safely and pleasanily is described Usage conditions applicable for infants Do not use for the infants who can not meet the following conditions This seat has been designed to accomodate children from birth to weight of 18kg which corresponds to an age of approx 4 years Driving direction Conditions applicable for infants Other conditions Important When Weight below Okg 11kg Group0 Adjust the angle Rearward Facing appropriately by using is used Age New bom 12months old the angle adjuster Make sure t
14. g on page 7 height of the infant s shoulder Refer to Height Adjustment of the Shoulder Belt on page 11 66 Click into locking The adjusting belt needs to be pulled to fasten Lock the buckle of the front pad Refer to Buckle the shoulder belt tightly Roba aid Kocama ine Page When adjusting the shoulder belt it is recommended to keep a space enough to allow a hand Unfolded of an adult to pass through between the infant chest and the shoulder belt Advice Are the buckle and the fastening plate firmly locked Is there any twisting in the shoulder belt and the adjusting belt is the adjusting belt securely locked is the shoulder belt firmly tightened over the infant is the shoulder belt correctly attached onto the shoulder belt hanger s the shoulder belt put on correctly to place the infant s pelvis in a stable position 10 Height adjustment of the shoulder belt The shoulder belt needs to be adjusted in its position suitably for the body of the infant The shoulder belt should be adjusted in its position suitably for the body of the infant The safety seat may not function fully when a situation occurs A Danger Note The shoulder strap comes in 2 positions upon the product shipment Adjust the height of the shoulder strap depending on a child s sitting height Shoulder belt hanger After the belt cover at the back side of the main body is removed the shoulder belt
15. han needed A Caution IVA ia Oe Tightly AYD Refer to the angle Angle indicator Itis used to install the safety seat in a correct ane y z rear viewing ies to 12 months old ones method for the infants ranging from newborn ba Adjust it while the car is on a level area Angle indicator bas gt a 14 Opposite the driving direction Rear viewing Weight Below 13kg Applicable eight Up to 75cm The attachment and fastening methods may vary depending on the kinds of the seat belt of a car Refer to Types of the Car s Seat Belts to Which the Safety Seat Can Be Attached on page 12 to fasten the infant safety seat correctly In case of ELR ALR mounted 3 point seat belt after the safety seat is attached the seat belt needs to be pulled to the end allowing the seat belt to change to the ALR function The shoulder belt needs not to be rolled up more than needed The direction in the picture on the left When the shoulder belt is rolled up too much the safety seat needs to be fixed again When you operate the locking lever you should be careful not to get your hands or fingers caught The back rest needs to be made upright Adjust the height of the shoulder strap and headrest appropriately to infant s body See the shoulder strap and headrest adjustment on page 11 amp 12 ne main body needs to be adjusted to the stage 4 by using the angel adjuster Refer to How to Use the Angle Adjust
16. hat the occipital le e Weght below 11kg 18kg Group region of the infant is not Forward Facing je 12months 4vears old positioned off the backrest dis Age d when the baby is seated Installation To install the seat in the car you have to use a 3 point automatic belt appoved to ECE16 or equivalent standard ECE European Safety Equipment Standard About the seat to which the safety seat will be attached it needs to be attached as shown below Use the car seat belt to attach it firmly Back seats The arrow shows the driving direction Front seat The arrow shows the driving direction zi A _ A Rear viewing Front viewing Rear viewing Front viewing The infant safety seat can be attached to the front seat or the back seats However it is recommended to attach it to the back seats where it is safer Do not use it for the passenger seat fitted with an airbag When activated the airbag may cause the infant to risk A Danger his or her life or suffer serious damage Danger When the product is used for the front seat in the rear viewing mode and interferes with the driving it should not be used About the seats to which the safety seat can not be attached If the safety seat can not be attached according to the user manual depending on the kinds of the seat belt of a car and thet Danger ypes of the seat the safety seat needs to be attached to other seats If the safety seat is not attached according
17. hed seat belt and fastening plate of a car need to be put through the belt passage along the backside of the main body A Caution Be careful not to cause the waist belt of the car to be twisted The detached waist belt of the car needs to be put through the belt passage The fastening plate of the car needs to be inserted into the buckle of the car Caution Be careful not to cause the waist belt of the car to be twisted 1 Slide the locking lever on the other end of the vehicle mounting plate sideway to unlock 2 Insert the car shoulder strap through the locking lever and slide the lever to the opposite side to lock it while pulling the strap tightly Position the strap under the lever and push the lever all the way to securely hold the strap A Caution The waist belt of the car needs to be pulled as much as possible to fasten it firmly without any shaking 15 slide the strap locking lever sideway and press down to fasten it while pulling the strap tightly using your body weight from above the car seat after checking if the car shoulder strap is properly inserted through the locking lever 6 Hang the car shoulder strap to the belt guide for dual fix of the strap initially fastened with the locking lever See how to use locking lever and belt guide on page 9 ASOT E HEJLOI 0 Diagram to show the installation O Diagram to show the installation in the car in the car
18. hould not be modified or its cover and the urethane part should not be removed when the seat is used The product should not be used in other ways rather than as described in the manual The safety seat may not fully function when a situation occurs When using the product for a new born baby Younger than 1 month after birth a fellow passenger not just the driver needs to get on the vehicle to pay attention to the baby Avoid using the product for longer than one hour consecutively in case of infants ranging from newbom babies to ones younger than 6 months considering the burden on them Be careful not to allow the infant to play on the safety seat You should not allow the infant to use it as a play apparatus Be careful not to allow any sharpened objects to cause damage to the car seat belt and the infant safety belt The belts may not function fully when a situation occurs When there is a problem with the belts You need to contact the selling shop for consultation It is recommended to use the back In case of the rear viewing mode seats for installing the infant safety the shoulder belt will not cause seat because they are safer any interference if the safety seat is ES installed on the seat behind the drivers seat vy Installing it while standing on the car lane is dangerous It is recommended to install the safety seat while standing on the sidewalk Accessories The design of the inner seat could
19. ing Lever on page 8 he main body needs to be made tight against the backrest in the opposite direction of the driving direction The base of the infant safety seat needs to be placed tightly onto the car seat The angle needs to be adjusted sufficiently to allow the ball of the angle indicator to move into the safe zone completely indicator as below For the infants ranging from newborn babies to 12 months old ones the angle appropriate for using the safety seat safely and pleasantly in a rear viewing mode is about 45 degrees In order to keep the angle of the safety seat at 45 sea hea the angle needs to be adjusted to allow the colored part Blue one of the angle indicator to move into the safe zone completely Adjust it while the car is on a level area X When the colored part is not within the safe zone adjustment needs to be made by placing something like cushion under the main body Cushion Shoulder belt of a car Belt passage Fastening plate of the car After the car seat is pushed tightly against the backrest of it you need to make the seat belt of the car come out by pulling it Danger The safety seat may not be fixed and fastened depending on the types of the waist belt of a car Refer to Types of the Car Seat Belts to Which the Safety Seat Can Be Attached on page 12 to fasten the infant safety seat correctly The detac
20. lt to keep the webbing tight to minimize the gap z Note Use rear facing installation procedure for front facing ISOFIX installation Rear Facing Installation Front Facing Installation 24 JA DAIICHI www babyseat net 82 2 Wunjeong 4 sa gil Paju City Gyeonggi do Korea 413 837 Tel 82 31 942 4324 Fax 82 31 942 4326
21. n to the vehicle How to Fasten amp Release Bottom Latch Pull the stopper lever in the front edge of ISOFIX base of the car seat forward from the both sides and then push the lever out of the ISOFIX base After aligning latches to anchors on the both sides push the car seat to securely fasten If it is difficult to connect the latches try connecting the latches by slightly rocking the car seat side to side after aligning the latches to the anchors Important 1 The side of a latch will be marked GREEN if it is firmly fastened If the indicator is RED instead of GREEN try re fastening again 2 If the indicator is marked GREEN pull the car seat forward to check the Latch is firmly fastened Note LATCH is a car seat fastener for infants that can be fastened to a fixed anchor between the backrest and the seat on the back seat of a vehicle 23 ISOFIX Installation Optional Release the latch by pulling the car seat forward while pressing the latch lever on the opposite side of the fixed control lever How to Connect Upper Tether The b mark in the picture on the left is located on the top edge of the rear seat backrest if the vehicle is designed to fit ISOFIX 1 Pull the webbing while pressing the length adjustment button red part for upper tether and hang the tether hook to the tether hanger behind the car seat 2 Tightly pull the tether be
22. needs to be pulled from the shoulder belt hanger Caution When the shoulder belt can not be seen the belt at the front side needs to be pulled by referring to How to Seat an Infant on page 10 Then the shoulder belt hanger will come out at the back side making it possible to adjust the height of the belt After seating the infant the belts need to be inserted through the holes at the most appropriate height for the infant s shoulders In case of the front viewing mode Holes that are seemingly positioned a little higher In case of the rear viewing mode Holes that are seemingly positioned a little lower Belt cover Every time an infant is seated the adjusting belt should be pulled Refer to How to Seat an Danger Infanton page 10 to seat the baby tightly If the shoulder belt can not function as originally designed consequently the infant may risk his or her life or suffering critical damage The belt cover should be attached and used If the belt cover can not function as originally designed the infant may risk his or her life or suffering critical damage 11 A Danger Headrest Adjustment Note For easy operation insert the shoulder strap through the hole on the backrest cover The headrest and shoulder strap move together from the 2nd position of the backrest height 1 Pull the head adjustment lever forward on the back of the car seat to adjust up
23. r Take out the fastening plate by pushing the press button within the buckle of the front pad Separate the fastening plate consisting of 2 parts into the upper and lower units Fastening plate v Fastening plate Press button Button Cover Put together the left and right parts by placing them into th l itions individually m into the upper and lower positions individually Insert the united fastening plate into heck 3 the buckle until there is a Click sound LA The fastening plate should be checked for its locking Click Z gt Bu ke Press button Button Cover T How to use the angle adjusting lever Front viewing mode 1 A 53 4 The angle can be adjusted in four stages with the 1st 3rd stages for the front viewing mode and the 4th stage for the rear viewing mode a Rear viewing a mode Incase of the front viewing mode the safety seat s angle needs to be adjusted according to the angle of the car seat to which the safety seat will be fastened Angle adjustment for Rearward facing mode ae een Below 13kg In case of the rear viewing mode for the infant safety seat it can be adjusted to the 4th stage Lever to change to the rearward facing mode Lay it down to the 4th stage The lowest laying position The angle adjusting lever needs to be Refer to the arrow on the main body for checking the pulled for pushing it backwards position of the angle adjustmen
24. r use it for the back seats When such inconvenience is caused it may interfere with operating the transmission gear or the side brake leading to a highly risky situation When there is a passenger in the back seat the safety seat should not be fastened to the passenger seat of a 2 door or 3 door vehicle or the secondary seat near the access area for ascending and descending in case of the one box type vehicle or a mini van in order to secure the emergency exit When there is no infant in the vehicle the infant safety seat needs to be stored for example in the trunk or fastened strongly within in a car When fastened insufficiently the safety seat may be shaking causing interference with driving When you need to ride together with an infant you should check the attachment of the safety seat again before driving the vehicle The safety seat needs to be checked for any problems during or after the driving The vehicle should be parked in a safe place first before the checking The safety seat should not be installed or removed while the infant is on it While driving you should not operate the infant safety seat Belt adjustment Angle adjustment for example The car should be parked in a safe place first before you operate the safety seat If you operate the safety seat while driving it is highly dangerous because your driving will be interfered with possibly leading to an accident The infant safety seat s
25. t Angle adjustment for Forward facing mode Applicable Weig Below 9kg 18kg In case of the Forward facing for the infant safety seat it can be adjusted in 3 stages ranging from 1st 3rd Lever to change to the Forward facing mode Adjust the angle of the product to one of the 3 stages The angle adjusting lever needs to be pulled according to the angle of the car seat Refer to the for pushing it backwards arrow on the side of the main body How to use the locking lever The locking lever is a device to attach the infant safety seat into the car firmly It should be used There are 2 locking levers located at the right and left side individually Use the product according to the attachment position The locking lever and the belt guide are used to attach the infant safety seat by using the car seat belt Danger They should be used If they are not used the safety seat may not be fastened when an impact or an abrupt stopping occurs possibly leading to a dangerous situation Before using the product it should be checked whether it can be attached onto your car seat Refer to About A Danger the Seats to Which the Safety Seat Can Not Be Attached on page 2 Even when the safety seat can not be installed as described in the user manual you should not use any forceful measures to fasten it The safety seat may not function fully when a situation occurs possibly causing an accident unexpectedly A Caution
26. to the user manual the infant may risk his or her life or suffering serious damage during the crash or the abrupt stopping A seat without a seat belt Impossible to fasten the infant safety seat A seat with a 2 point seat belt Impossible to fasten the infant safety seat Donot place a child seat rear facing in the front seat of a vehicle with a passenger air bag uniess deactivated DEATH OR SERIOUS INJURY can occur Aseat with a seat belt located in the middle of a seat Impossible to fasten the infant safety seat strongly Picture 1 Aseat with an airbag When activated the airbag may cause the infant to risk his or her life or suffer serious damage A seat placed sideways or opposite the driving direction Difficult to absorb the crash impact Seats whose width and length are less than 45cm The attached safety seat will be made unstable A seat that could interfere with driving when installed with the infant safety seat or the front central seat Difficult to secure the safety of people in the car A seat whose buckle is highly placed and to which the safety seat can not be fastened The infant safety seat can not be installed Picture 2 Other seats to which the safety seat can not be fastened Picture 1 Picture 2 Caution The user manual needs to be kept well and read accordingly when necessary The infant safety seat needs to be attached according to the user manual If the seat is attached inappropriately
27. ulled to the end mounted 3 point seat belt ALR function allowing the belt to be recoiled allowing the belt to shift to the ALR function Belt locking device automatically When the belt is recoiled to i When the seat needs to be installed that can fasten the the end it will change to the ELR function A Caution you need to refer to the user manual of the infant safety seat car to which the safety seat will be attached AL R When you stop in the middle of pulling out In order to fasten the infant safety seat the point type seat belt the belt the belt will be locked automatically belt should be pulled at once to the length Belt locking device hot allowing it to be pulled further necessary for fastening The safety seat needs that can be locked to be fastened firmly by using the locking lever automatically L R Normally the belt can be released and mounted 3 point seat belt recoiled freely When the seat detects an The safety seat needs to be fastened firmly i i impact Including an abrupt stopping by using the locking lever Lente Re the belt will be locked at the current position TE i automatically without any loosening ELR mounted seat belt ELR mounted seat belt without a cars shoulder belt The safety seat can not be fastened firmly NLR point type seat belt There is no locking function Its length needs Belt locking seat belt to be adjusted while it is pulled to the end that is not to be lo
28. vary depending on products dj D Side cushion Inner seat Manual Shoulder pad x Safe Keeping of Manual How to Use Side Cushion Keep the manual inside Side cushion is recommended for infants under a belt cover on a backside of the car seat 6 months Position the cushion to support a child s head from both sides Name of parts Shoulder belt hole 4 stages Shoulder pad Fastening plate buckle Belt length adjusting lever Angle adjusting lever Lever to change to the rearward facing Head Sheet Seat cover Shoulder belt Upper base ISOFIX latch Belt cover ISOFIX top tether hook Belt Guide For Rear Facing Installation I Wy ForR Sra angie Indicator or Rear Facing Installation A Belt locking lever wo H For Forward facing Mode w ij o Belt passage NU TT iN SG 4 ISOFIX latch lever When removing the belt cover Length of the belt cover The shoulder belt hanger is necessary fo adjusting the height of the shoulder belt How to operate Buckle releasing and locking Individual functions should be operated while the care is parked If you operate them while you drive it may NWaming HR interfere with driving possibly leading to an accident Danger Using the infant safety seat while its buckle is released is dangerous so it should not be allowed in any way Releasing 1 Fastening plate 2 IS 5 Fastening plate Buckle Press button Button Cove

Untitled

Contents

Download Pdf Manuals

Related Search

Related Contents