MAN 091-TEL 040 LP
Contents
1. 091A2. People Hear Tele Talker Model TEL 040 Installation Guide amp User Manual SPECIFICATIONS Tele Talker Amplified Elephone Model TEL 040 Dimensions Color Wide band Gain High Frequency Gain Audio Freq Response Max HF Acoustic Gain Sat Acoustic Output Total Harm Distortion Signal to Noise Ratio Signal Processing Noise Reduction Ringer Volume Control Ringer Loudness vV PTP Of Williams Sound 2 2 D 8 9 H 7 6 W 56mm D 226mm H 192mm W White with dark gray controls 25 dB maximum 30 dB maximum 300 Hz to 2800 Hz 3 dB 55 dB 130 dB SSPL lt 3 at 120 dB SPL output 1000 Hz Enhance control at min 51 dB NAB Weighted Dynamic Signal Processing Dynamic Noise Reduction DNR Hi Lo Off 90 95 dBA SPL at 1 meter Hi position Installation Guide amp User Manual Tele Talker Model TEL 040 Ringer Pitch Control Adjustable 3 positions lo med hi Flasher J umbo LED high visibility red Connections 2 wire central office connec tion modular plug Ringer Equivalency Number REN 1 0B Power Includes 12 VAC power supply Warranty Five Years Parts and Labor Trademark of National Semiconductor Com 90 dayson cordsand power supply Williams Sound Corp 10399 West 70th St Eden Prairie MN 55344 3459 U S A 800 328 6190 612 943 2252 FAX 612 943 2174 www williamssound com info williamssound com 1998 Williams Sound Corp MAN
3. position and hold the handset close to your hearing aid The volume can be adjusted with the TeleTalker volume control V ATP Ol Wiliams Sound 17 Installation Guide amp User Manual Tele Talker Model TEL 040 In Case Of Difficulty Cannot hear the other person speak This only occurs when the TleTalker is in Amplify mode When you use the Amplify feature the TeleTalker operates in half duplex mode This means that while you speak the handset receiver shuts off If it did not the extremely loud volumes produced by the TeleTalker would cause feedback When using the TeleTalker in Amplify mode do not speak when the other party is speaking Can answer calls but cannot make them The pulse tone switch is set in the wrong position Change it to pulse mode No dial tone when you pick up handset There are anumber of potential causes to this prob lem 1 Cords on handset or phone are not plugged into jacks Make sure connectors are plugged in securely 2 The cord could be damaged If so replace the cord vV ATP 18 Of Williams Sound TeleTalker Model TEL 040 Installation Guide amp User Manual 3 The wall jack could be improperly wired Check the wall jack for proper wiring 4 Your phone line could be out of order Contact your local phone company Can make calls but phone doesn t ring for incom ing calls There are a number of potential causes to this prob lem 1 The handset may not be placed
4. properly on the base Make sure it is resting properly on the base 2 The Ringer Volume Control may be set to OFF Adjust the switch to LO or HI 3 Too many phones or phone devices may be con nected to the same line If so remove other phones or devices from line 4 The Pulse Tone Switch may be in the wrong posi tion Your phone line may be set to accept only pulse dialing If so be sure to set this switch cor rectly 5 Your older extension phone may cause the TeleTalker to cut off If so use Williams Sound s optional Equalizer Phone Accessory TEL 007 The Equalizer balances the amount of phone line current drawn by older phones using the same line as the TeleTalker vV OU Wiliams Sound 19 Installation Guide amp User Manual Tele Talker Model TEL 040 Viananty Williams Sound Products are engineered and manu factured to give many years of trouble free service Occasionally latent defects will occur If this hap pens return the product to us with shipping cost prepaid and advise us by letter of the observed diffi culty During the first five years following the date of pur chase we will promptly repair or replace the prod uct and return it at our expense After five years from the date of purchase we will service our prod ucts for a modest service charge Please return the enclosed warranty card to register your date of pur chase This warranty does not extend to intentional or accidental physi
5. your local telephone company you provide the following informa tion A The line to which you will connect the telephone equipment your phone number B The telephone equipment s FCC registration number and Ringer Equivalence Number REN These numbers are on the back or bottom of your telephone equipment The REN is useful to determine how many devices you may connect to your telephone line and still have them ring when your telephone line is called In most but not all areas the sum of all REN s should be 5 or less You may want to contact your local telephone company if you experience prob lems Repair instructions If it is determined that your telephone equipment is malfunctioning the FCC requires that it not be used and that it be unplugged from the modular outlet until the problem has been corrected Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents or by others who may be authorized by the FCC For repair procedures follow the instructions under the section entitled Warranty Rights of the telephone company If your product is causing harm to the telephone network the telephone company may temporarily dis continue your telephone service If possible they will notify you before they interrupt service If advance notice isn t practical you ll be notified as soon as possible You ll be given the opportunity to correct the problem and you ll be informed of your right to f
6. Do not plug the telephone back in until it has dried thoroughly Avoid using the telephone during electrical storms in your immediate area Urgent calls should be brief Even though your telephone company may be using protective measures to limit electrical surges from entering your home absolute protection from lighting is impossible If you suspect a gas leak report it immediately But use a telephone away from the affected area The telephone s elec trical contacts could create a tiny spark While unlikely it is possible this spark could ignite heavy concentrations of gas Installation Guide amp User Manual Tele Talker Model TEL 040 Table Of Contents Contents Page Safety Information 2 Introduction 5 Components 6 Features amp Functions 7 Installation Steps 8 Table Desk Installation 10 Wall Plate Installation 11 Bare Wall Installation 13 Tele Talker Operation 15 Using TheAmplify Function 15 Making A Call 16 AnsweringA Call 16 Using The TeleTalker With A Hearing Aid 17 In Case Of Difficulty 18 Viananty 20 FCC Notices 22 Specifications 23 vV ATA Of Williams Sound Tele Talker Model TEL 040 Installation Guide amp User Manual Introduction Congratulations on the purchase of your TeleTalker Enhanced Amplified Telephone System Model TEL 040 This state of the art Williams Sound product is designed and built with premium quality parts for your assurance of reliability The TeleTalker is designed to i
7. Rlielalker Installation Guide amp User Manual Model TEL 040 MAN 091 x A Williams Sound Helping People Hear Important Safety Information Statements in this manual preceded by the following words are of special significance WARNING Means there is the possibility of personal injury to yourself or others CAUTION Means there is the possibility of damage to the equipment Other information of particular importance has been placed in italic type like this WARNING The TeleTalker is capable of amplifying sounds to a very loud volume To prevent misuse of the phone by someone who Is unfamiliar with its operation and capabilities DO NOT remove the warning labels Instruct all potential users in its proper operation Do not let children play with the TeleTalker When the AMPLIFY function is not activated the TeleTalker functions as a normal telephone VARNING This telephone can produce very high loud sound levels Always adjust controls to minimum settings before using the phone and alert other users that hearing damage can poten tially result from misuse WARNING This product can be hazardous if immersed in water To avoid the possibility of electrical shock do not use it while in the bathtub or shower or when you are wet If you acci dentally drop it into water do not retrieve it until you have first unplugged the line cord from the modular wall jack and the power pack from theAC wall outlet
8. cal damage or damage caused by leaking batteries Cords and power supply are war ranted for 90 days This warranty applies only to products returned to Williams Sound for service vV ATH 20 Of Williams Sound Ple Biker Model TUU es nstallaton Guide amp User Manya To return a product for service call the phone num ber below and request a Return Authorization RA number Unauthorized modifications or repairs of the product will void the warranty Williams Sound Corp 10399 West 70th Street Eden Prairie MN 55344 3459 Phone 1 800 843 3544 1 612 943 2252 Fax 1 612 943 2174 Web www williamssound com info williamssound com V ATP Ol Wiliams Sound 2d Installation Guide amp User Manual Tele Talker Model TEL 040 FCC Registration Notice Your new TeleTalker product has been registered with the Federal Communications Commission FCC This prod uct complies with standards in Part 68 of the FCC Rules The FCC requires us to provide you with the following information 1 Connection and use with the nationwide telephone network The FCC requires that you connect your product to the nationwide telephone network through a modular telephone outlet or jack The modular telephone outlet or jack to which the telephone must be connected is a USOC RJ 11C or RJ 11W This equipment may not be used with Party Line Service or with Coin Telephone Lines Notification to the telephone company The FCC requires that upon request of
9. f Difficulty page 18 Note To remove a wall mounted telephone slide the phone up and pull it slightly away from the wall Disconnect the line cord by squeezing the clip on the modular plug and pulling it from the jack fig 7 Wall Installation Short Vall Cord vV aj 12 Of Williams Sound Tele Talker Model TEL 040 Installation Guide amp User Manual Bare Viall Installation Even if you don t have a studded wall phone plate you can still mount the TeleTalker on any wall sur face within six feet of a standard modular jack and AC outlet To mount the phone farther from the Jack you ll need a longer line cord or a telephone extension cord In either case place the AC power pack in alocation which will not be subject to dis turbance Step 1 Measure and mark the wall for mounting SCrews Mark two points 3 14 inches apart for upper and lower mounting screws The lower mark should be 48 52 inches from the floor Use a level to make sure the marks are aligned vertically Step 2 Install the mounting screws not included Use wood screws for stud mounting anchor screws for hollow wall mounting Drive the screws almost completely in leaving a 18 inch space between the wall surface and the bottom of the screw head about the thickness of two stacked pen nies vV OU Wiliams Sound 13 raaton Guine amp Uer Manual ace a et ce Step 3 Reverse the handset hanger to prevent the handset from falling Ste
10. ile a complaint with the FCC Your telephone company may make changes in its facilities equipment operations or procedures that could effect the proper functioning of your TeleTalker product If such changes are planned you ll be notified This telephone is compatible with inductively coupled Telecoil hearing aids Interference Information Part 15 Of FCC Rules Some telephone equipment generates and uses radio frequency energy and if not installed properly may cause interference to radio and television reception Your TeleTalker product has been tested and found to meet the standards for a Class B computing device as speci fied in Subpart J of Part 15 of the FCC Rules These specifications are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If your TeleTalker product causes interference to radio or television reception when it s in use you might correct the interference with any one of these measures Where it can be done safely re orient the receiving telephone or radio antenna To the extent possible relocate the television radio or other receiver with respect to the telephone equip ment If your telephone product runs on AC power plug your product into an AC outlet that s not in the same circuit as one used by your radio or television 22 K JA Williams Sound Helping
11. mprove the audibili ty and understandability of incoming voice signals by reducing unwanted line noise It s also designed to improve the clarity of the sound signal by empha sizing higher frequency speech sounds The TeleTalker functions as either an amplified tele phone or as anormal telephone for users who don t need amplification We suggest you read this user manual carefully to become familiar with the TeleTalker s features and their function The manual explains how to install use and care for your new TeleTalker WV ATA Of Williams Sound a Installation Guide amp User Manual Tele Talker Model TEL 040 Components The following items are included with the TeleTalker e Handset e Base e Coiled handset cord Wall cords 2 e Power pack e User Manual Features amp Functions Amplify Button Activates Amplify and Enhance functions Amplify Indicator Lights when Amplify function iS on Enhance Control Increases high frequency sounds high frequency boost Volume Control Increases sound volume Ring Indicator Flashes when TeleTalker rings Redial Button Redials last number dialed Pulse Tone Switch Selects Pulse rotary phone systems or Touch Tone Dialing Ringer Volume Adjusts Ringer volume level Ringer Tone Control Adjusts Ringer tone vV PTP 6 WY Wiliams Sound Tele Talker Model TEL 040 Installation Guide amp User Manual Fig 1 TeleTalker Features amp Functions Fla
12. one dialing will not work if you have only dial pulse rotary service fig 2 Pulse Tone Switch Pulse Tone Switch Switc hes between touch tone and rotary dial modes vV J 8 WY williams Sound Tele Talker Model TEL 040 Installation Guide amp User Manual Step 3 Set Ringer Volume and Tone Controls to desired level see fig 3 fig 3 Ringer Controls Ringer Volume Control Ringer Tone Control Adjusts ringer volume Hi Lo Off Adjusts ringer pitch I Il Ill Step 4 Plug the coiled handset cord into the hand set Plug the other end into the telephone base see fig 4 fig 4 Handset Connection Step 5 Plug the Power Pack cord into the Power Jack located at the top end of the tele phone Plug the Power Pack into an unsw itched AC outlet within 6 feet of the telephone see fig 5 V ATA WY Williams Sound g Installation Guide amp User Manual Tele Talker Model TEL 040 fig 5 Power Connection Power Jack Power Pack Step 6 Perform either Table Desk installation or Wall installation as outlined on the follow ing pages For Table Desk Installations Step 1 Plug the long line cord into the jack on the back of the telephone base see fig 6 Step 2 Plug the other end of the line cord into a modular baseboard jack Make sure both ends snap into place firmly see fig 6 fig 6 Line Cord Connection vV ATH 10 Y Williams Sound Ple Biker Mogel EUU sni ns
13. p 4 Mount the TeleTalker Hang the telephone on the mounting screws and push down gently until it snaps into place Step 5 Connect the line cord to the jack on the top of the phone Plug the other end of the line cord into a modular wall jack Make sure it snaps firmly into place Step 6 Connect the AC power pack to a wall AC outlet Step 7 Check for the dial tone If you can t hear a dial tone see In Case Of Difficulty page 18 Note To disconnect the telephone squeeze the clip on the modular plug and pull it out of the jack W ATA 14 Of Williams Sound Tele Talker Model TEL 040 Installation Guide amp User Manual Tele Talker Operation Using The Amplify Function Before activating the Amplify function turn the vol ume and enhancement controls to their minimums counter clockwise To activate amplification press the red Amplify button The red indicator light will glow when activated The Amplify function auto matically turns off when you hang up the phone WARNING The TeleTalker is capable of amplifying sounds to avery loud volume Always set the VOLUME CON TROL to the MINIMUM setting before using the phone To prevent misuse of the phone by some one who is unfamiliar with its operation and capa bilities DO NOT remove the warning labels Instruct all potential users in its proper operation Do not let children play with the TeleTalker When the Amplify function is not activated the TeleTalke
14. r functions as a normal telephone Using The Volume Control Turn the volume control knob clockwise to increase volume counter clockwise to decrease volume vV OU Wiliams Sound 15 Installato Guide amp User Manual occ IS AIKET Moger TEL 040 Using The Enhancement Control Turn the Enhance control knob clockwise to boost high frequencies counter clockwise to decrease the boost of high frequencies Making A Call Step 1 Lift the handset and check the Volume Control setting Step 2 Press the Amplify button The Red LED should light Step 3 Adjust the Volume and Enhance Controls to comfortable levels Step 4 When you hear a dial tone dial the num ber and use as a regular phone Adjust the volume and enhancement controls for best understanding of the remote party Step 5 When you hang up the phone the Amplify function automatically turns off Answering A Call Step 1 Check the Volume Control setting lift the handset Step 2 Press the Amplify button The red Amplify indicator should light vV ATP 16 Of Williams Sound Ect Mogel TTO ruie natala non Gulda amp Toer Manyar Step 3 Adjust the Volume and Enhance controls to comfortable settings Step 4 When you hang up the phone the Amplify function automatically turns off Using the Tele Blker With A Hearing Aid The handset can be used directly with hearing aids equipped with a telecoil T coil Move your hear ing aid T switch to the T
15. shing Ring Indicator Flashes red to indicate ring Special Handset Speaker Provides superior sound quality Dynamic Signal Processing Improves speech clarity Dynamic Noise Reduction DNR Removes unwanted background line noise Ant Feedback Circuitry Prevents howling feedback at high volume x A Williams Sound Helping People Hear Pulse Tone Switch Toggles between Pulse and Touch Tone dialing modes Amplification Indicator Glows red when call is amplified Volume Contol Boosts volume up to 25 dB activated by Amplify button Amplify Button Push this to amplify your call Enhance Control Boosts high frequency speech sounds up to 30 dB activated by Amplify button Adjusta ble to meet your individual needs Ringer Volume Contol Adjusts ringer volume up to 95 dBA Hi Lo amp Off Redial Button Automatically redials last number called Installation Guide amp User Manual Tele Talker Model TEL 040 Installation Steps Step 1 Make sure you have a 115 VAC wall outlet and telephone jack within 6 feet of the place you ve chosen to install the tele phone If you have an older 4 prong Jack you ll need a modular jack adapter These adapters are available from electronic phone and other retail stores Step 2 Place the Pulse Tone Switch located on the side of the phone in either Tone or Pulse Rotary Dial Pulse Make sure you choose the correct dialing mode T
16. tallaton Gulda amp User Manya Step 3 Lift the handset and check for dial tone If you don t hear a dial tone see In Case Of Difficulty page 18 Note To disconnect squeeze the clip on the plug and pull it out from the jack Remove the Power Pack plug from telephone For Viall Plate Installations If you prefer the TeleTalker can also be mounted on a studded wall phone plate If you don t have a phone plate installed talk to your phone company or local phone products store Step 1 Clip the plastic wall mounting bracket included into bottom of the TeleTalker base unit see fig 7 on following page Make sure the tabs snap in securely This will make the base unit level with the wall Step 2 Reverse the handset hanger found in the handset cradle to prevent the handset from falling Step 3 Plug the short line cord into the jack on the top of the telephone and thread the line through the channel to the cavity on the back of the base unit V ATP Py Wikiams Sound 11 Inst e vow Guilde amp user Vanual ce Oe TEE 0g Step 4 Hold the telephone next to the wall phone jack and plug the line cord into the jack leaving any slack in the base unit cavity Then push the phone against the mount ing studs so the studs are hooked into the upper and lower keyhole slots of the phone Slide the phone down until it snaps into place see fig 7 Step 5 Check for a dial tone If you can t hear a dial tone see In Case O
Download Pdf Manuals
Related Search