User Manual - DynaPowerUSA
Contents
1. NA260A Guide External PCle to GPU Enclosure Version 1 0 NAZ60A Rackmount External PCle to GPU Enclosure D Overview Panel layout The easy and cost effective PCle to PCle expansion system TurboBox Rac NA260A features easy plug and play installation containing PCle 2 0 x8 host card and data cable for up to 40 Gbps high speed transfer rate The TurboBox Rac NA260A is configured by the BIOS from the workstation or server automatically which makes all the PCle slots on TurboBox Rac NA260A available to the server or Slotl PCle x16 connector x8 signal Slot2 PCle x16 connector x8 signal Slot3 PCle x4 connector x4 signal Slot4 PCle x16 connector x8 signal Slot 5 PCle x4 connector x4 signal Slot 6 PCle x16 connector x8 signal 8 x 6 2 pin PCI Express power connectors for graphics cards To server or workstation the speed of the PCle slots on NA260A runs at PCle x8 40 Gbps NO UU BWYN workstation a Package checklist Installation of PCI Express Before the installation of this unit verify the package contains the 432 1 5 6 m gg Add On Graphics Card following items 1 Power on off button Before following the installation procedures disconnect Blue power on TurboBox Rac NA260A from power source to prevent Note To power on off the TurboBox Rac NA260A press the electric shock or damage to add on graphics card button for two seconds 1 First loosen the two thu2. adapter into an available PCle x8 connector compatible with x16 connector in server or workstation Secure the host adapter with a screw A motherboard 2 Connect the other end of PCle x8 cable to TurboBox Rac PCle 2 0 x8 host adapter on server or workstation 7 Power On TurboBox Rac NA260A Power on the TurboBox Rac NA260A by pressing the power button for two seconds 8 Power On Server or Workstation In order to let the BIOS of server or workstation identify and assign resources appropriately make sure to power on TurboBox Rac NA260A first and then power on server or workstation There is no software required for proper configuration of TurboBox Rac by server or workstation s operating system however as a third party PCle card is installed in TurboBox Rac a request for the driver of the third party PCle card will be prompted by the operating system Please follow the instruction provided by the third party PCle card Remove TurboBox Rac from Server or Workstation To remove TurboBox Rac NA260A from server or workstation power off server or workstation first and then power off TurboBox Rac 10 Verify Installation To remove TurboBox Rac NA260A from server or workstation power off server or workstation first and then power off TurboBox Rac For Windows operating system When you want to verify a successful installation on Windows operating system go to My Computer and
3. bridge PCi to l Bridge Yes PC Soe 207 20 Fibre Ouma pess500 Camotes Cort ves PCr Spano When the driver of the third party PCle graphics card is installed on Mac OS X your server or workstation will begin working with the third party PCle graphics card on TurboBox Rac
4. party PCle graphics card will be shown under PCI standard PCl to PCI bridge furthermore the name of the third party PCle graphics card will also be shown in the list of Device Manager Sp WDE 14 Bs best cortroders D Unbowd E D Me and other porting devices Morton Meotewort edaoters i pane resos sound wio sd game cortroiers For Mac OS To verify a successful installation on Mac OS X select About This Mac under the Apple icon 0o00 About This Mac gt Mac OS X Version 10 6 4 Processor 2 x 2 26 GHz Quad Core Intel Xeon Memory 6 GB 1066 MHz DDR3 Startup Disk Macintosh HD TM and 1983 2010 Apple Inc All Rights Reserved Click More Info from the window Log Out Nelson Click PCI Cards from the left side of the window and when there is no third party PCle graphics card plugged in TurboBox Rac you will see six pci bridges that indicate six PCle slots on TurboBox Rac AAD Mac Pro Welton Mar Pro TOIL FFEN Sint Sk 1 I Ske Ike DHT 2 0 Ske 207 2 0 j R i 3 g 3 j sat 33232385 When a third party PCle graphics card is plugged in one of the PCle slots on TurboBox Rac the third party PCle graphics card will be shown under the six pci bridges Mac Pro WOLU FFAS es sa Jopay ro se ATA pci bridge PCi to PC Bridge Ves O So O Soe ap7Ao PO ee 207 20 PCI Sot 207 2 0 Ox borrero pcr bridge Fito Didge ves PO So2or2o Ethereet Cards po
5. thumbscrews to fasten the top cover Step 4 5 Connect the end of PCle x8 cable to PCle x8 connector on rear panel of TurboBox Rac NA260A Also connect the end of power cord to power receptacle on TurboBox Rac NA260A and the other end of power cord to a grounded outlet or power strip PCle x8 cable Note there are three hot swappable 120x120x25 mm cooling fans for ventilation inside TurboBox Rac NA260A You may simply draw the cooling fans out by pulling the L type metal handle on the fan modules Q Fan Speed Adjustment You are able to adjust the speed of 120x120x25 mm cooling fan inside TurboBox Rac NA260A To do so pull the cooling fan out and you will see five sets of jumpers labeled with F 1 2 3 and 4 respectively from left to right on the board The default setting is the jumper being placed over pin 9 and pin 10 for label 4 meaning the slowest speed of fan If the jumper is placed over pin 1 and pin 2 for label F the fan will spin at full soeed From label 1 to label 3 the fan speed decreases If all of the pins are open meaning no jumper is placed over the pins the fan will not spin 1 3 5 T 9 Q Installation of Host Adapter and Cable Connection Before following the installation procedure disconnect the server or workstation from power source to prevent electric shock or damage to add on graphics card 1 Install TurboBox Rac PCle 2 0 x8 host
6. mbscrews and remove the top 2 Buzzer mute button cover from TurboBox Rac NA260A 3 Fan LED Green normal Red fan failure low frequency of RPM or stop 4 Temperature LED Green normal Q TurboBox NA260A x 1 Red overheated higher than 55 C Step 1 5 Power switch PCle 2 0 x8 host adapter with 6 Power receptacle standard and low profile bracket x 1 7 60x60 x25 mm hot swappable cooling fan 8 External PCle x8 connector for host connection 2 Bend the L shape metal bracket on rear panel of 9 PCle slots TurboBox Rac NA260A for preparation of the installation 10 Thumbscrew to loosen tighten the side door Otte 20d One iap Mics Garg PCle 2 0 x8 cable 1 5 meter x 1 Power cord x 1 Step 2 Note it is easier to use a screwdriver to bend the L shape metal bracket CD containing user manual x 1 7 654321 1 23456 NAZ60A Rackmount External PCle to GPU Enclosure 3 Insert a PCle add on graphics card into PCle x16 slot and tighten it with a screw If you are installing a graphics card that requires extra power resources connect the 6 pin PCI Express power resource provided by NA260A to the 6 pin PCI Express power connector on graphics card or connect the 6 2 pin PCI Express power resource provided by NA260A to the 8 pin PCI Express power connector on graphics card 4 Place the top cover back to TurboBox Rac NA260A and tighten the two
7. right click the icon of My Computer Select Manage from the menu see figure 10 1 and click Device Manager in the left side of window of Computer Management see figure 10 2 NAZ60A Rackmount External PCle to GPU Enclosure Figure 10 1 oy npr Aare r Figure 10 2 And then click View from the top side of the window and select Devices by connection E Lempuler Maire r Open ACPI Multiprocessor PC open Microsoft ACPI Compliant System open PCI bus click PCI Express Root Port click PCI standard PCl to PCI bridge and click again PCI standard PCl to PCl bridge And then you will find your third party PCle graphics card under PCI standard PCI to PCl bridge Note You may see PCI Express Root Ports with different ending numbers such as 2E21 2E29 and 2E20 These different ending numbers indicate different PCle slots on motherboard EEEEEE You will see six PCI standard PCI to PCl bridges below the PCI Express Root Port Note If there is a yellow exclamation mark in front of the third party PCle graphics card under PCI standard PCI to PCl bridge it means the third party PCle graphics card is without the driver so you have to install its driver on operating system to make it work with the server or workstation After the driver is installed on operating system the third party PCle graphics card will work properly with the server or workstation via TurboBox Rac and the name of the third
Download Pdf Manuals
Related Search