Mania EF3 - Eurydice
Contents
1. at least 20 minutes Maximumambienttemperature T 40 C 104 F INSTALLATION Minimum distancetoflammablematerial 0 3 m 1ft Minimum distancetoilluminatedsurface 1 0 m 3 3ft Minimumclearancearoundairvenis 0 1 m 4in CONTROL AND PROGRAMMING Stand alonetriggers music or auto ELECTRICAL leif e A tae Ma e M terr ts 3 prong IEC male socket AC Power switch selectable operating ranges 115 120 V 220 240 V 50 60 Hz Mainf se respecte he nr BEN 2 AT time delay TYPICAL POWER AND CURRENT 120 V NEE di da 115 W 1 0A ZON KEE 113 W 0 9 A 230 V 90 HZ hk ete RE p Reds kdo EI EE PR 106 W 0 5A 230 V 00 HZ 5e chu Sb b negabat bete sas 105 W 0 5A 240 V 50 HZ c ex oos her a ER PIA m ge ente 114 W 0 5A 240 NV OO HZ Loch E ebd DAMES ent ae 113 W 0 5 A INCLUDED ITEMS US VERSION 2 m 6 5 ft US mains cable 18AWG with US male connector UL approved Philips 12V EFP 8H 100W lamp User manual INCLUDED ITEMS NON US VERSION 3 m 9 8 ft EU mains cable 3x1 Omm with Schuko male connector 3 m 9 8 ft EU mains cable 3x1 0mm with no male connector Philips 12V EFP 8H 100W lamp User manual ACCESSORIES Philips 12V EFP 8H 100W lamp P N 97000004 Half couplerclamp P N 91602005 Fuse 2 AT e li Ebo Dass P N2. The lamp shall be changed if it becomes damaged or thermally deformed If the external power cord of this luminaire is damaged it shall be replaced by a special cord exclusively available from your Martin dealer Avoiding electric shocks Warning Always disconnect from mains power before replacing the lamp fuses or any part and when not in use Before operation ensure that factory setting of voltage and frequency match local power supply Always ground earth the fixture electrically Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault protection Do not expose the fixture to rain or moisture Never operate the fixture with missing or damaged lenses and or covers Protecting yourself and others from burns and fire Warning Hot lamp The exterior of the fixture can become hot Allow to cool for at least 20 minutes before handling or opening Surface temperature under steady state condition 100 C 212 F Minimum distance to flammable material 0 3 m 1 ft Minimum distance to illuminated surface 1 0 m 3 3 ft Never attempt to bypass the thermostatic switch or fuses Always replace defective fuses with ones of the specified type and rating Ensure that the air flow through vents is free and unobstructed Provide a minimum clearance of 0 1 meters 4 inches around air vents Never place filters or other materials over the lens or in the opt
3. switch is set to O In Auto trig mode the wheel will rotate when switch is in position I or Il In Music trig mode the wheel will react to the beat of the music in position Il or will spin continuously in position I Gobo wheel rotation switch Operation 11 12 Note that it is the whole wheel and not the individual gobos that rotates FOCUSING THE MANIA EF3 The focus is adjusted using the mechanism next to the lens This is easiest to do in Music Trig mode while no music is being played Pull the mechanism out or push it in until a sharp image is acquired N Os A Mania EF3 user manual BASIC SERVICE Warning Important This chapter describes the maintenance procedures that you can perform yourself The exterior of the fixture can become hot Always disconnect the fixture from AC power and allow to cool for at least 20 minutes before handling or opening CLEANING Regular cleaning of the elements in the optical path as well as the air vents is vital to maintaining the operational quality of the Mania EF3 Excessive dust smoke fluid and particulate buildup degrades performance and causes overheating and damage to the fixture that is not covered by the warranty Cleaning the air vents To maintain adequate cooling dust must be cleaned from the air vents periodically Remove dust from the air vents with a soft brush cotton swab vacuum or compressed air Cleaning optical com
4. 05020009 ORDERING INFORMATION ManiaEF3non USversion P N 90430062 Maniaer3USsversion P N 90430063 A Martin www martin com e Olof Palmes Alle 18 e 8200 Aarhus N e Denmark Tel 45 8740 0000 e Fax 45 8740 0010
5. Mania EF3 user manual y Martin Measurements are expressed in millimeters 2004 Martin Professional A S Denmark All rights reserved No part of this manual may be reproduced in any form or by any means without permission in writing from Martin Professional A S Denmark P N 35000159 Rev A Introduction ooh ewe UA Led m 4 Safety Information 4 Unpacking 14 ete eem eg tes eee een EE 6 Mania EFS Overview 2 EN eig Rr ERE REOR de deve ae e eed 6 Installati n ee san ar pees Doi om antes eat AN aat mer d sab utat dios he i 7 AG DOWGL sez ii a LAN ne diu CR de HEN ER Pod TL RR es 7 Overhead mounting 8 Operation ooo ors Doer elle ifs ad Rack ege i or ted 10 Setting the trig mode 10 The gobo wheel 2 0 ll nn 11 FocusingtheManiaEF3 12 Basic ServiCe Sn nat sf poris ctt fabula 13 ES Ile iere rh Cases Ip On Binet apttd ice aceti unt feres wardens 13 Eamp mM intenance sp vi Nee e E ede be x edid 14 Mainsfuse x 24 5 ec veis erue eR Em IB SES 16 Troubleshooting 18 INTRODUCTION Warning Thank you for selecting a Martin Mania EF3 The Mania EF3 is a pre programmed music activated dynamic lighting fixture that features a motorized rotating reflector with coated mirrors and a motorized rotating wheel with 8 gobos gobos are outl
6. ecomes damaged or thermally deformed Mania EF3 user manual Caution Hot lamp Only the Philips 12V EFP 8H 100W type No 6834 lamp is supported Martin P N 97000004 These lamps normally last for 800 hours of operation Warning Installing any other lamp may damage the fixture Installing a lamp in the Mania EF3 1 Disconnect the fixture from power and allow it to cool for 20 minutes 2 Remove the thumb screw holding the cover in place SEET Thumb screw 3 Slide the fixture cover open as far as possible there is a physical stop point that prevents access to the power supply section 4 Grasp the old lamp by the reflector and slide it carefully out of the lamp holder Basic service 15 5 Pull the socket off the lamp Do not pull the wires 6 Push the socket fully onto the pins of the new lamp 7 Clean the glass bulb and reflector with a cloth particularly if your fingers touched the glass A clean lint free cloth wetted with alcohol is best 8 Gently push the lamp into the holder until it snaps into place 9 Close the fixture cover and tighten the thumb screw MAINS FUSE The Mania EF3 uses a time delay fuse for protection against current overload An indication that the fuse may have blown is that when power is applied and the lamp is switched on no light is produced If the fuse blows repeatedly there is a fault with the unit that requires service by a Martin technician Never bypass the fuse or r
7. eplace it with one of another size or rating Replacing the main fuse 1 Unplug the mains cable from the input socket 16 Mania EF3 user manual 2 Pry open the fuse holder located next to the mains power connector with a flat head screwdriver and remove the fuse Fuse holder 3 Replace the fuse with one of the same type The fuse rating is listed on the serial number label and in Mania EF3 specifications on page 19 4 Replace the fuse holder Basic service 17 TROUBLESHOOTING problem probable cause s suggested remedy No light No power to the fixture Check connections Blown fuse If power is applied and the lamp is switched on but does not light then check and replace fuse if necessary Burned out lamp Install new lamp Fixture too hot Allow to cool Improve air flow around fixture No action Sound too low to activate Increase volume control circuit Move speakers closer Electrical malfunction Refer to a Martin service technician Fuse blows repeatedly Electrical malfunction Refer to a Martin service technician 18 Mania EF3 user manual MANIA EF3 SPECIFICATIONS PHYSICAL Size without mounting bracket LxWxH 312 x 250 x 142mm 12 3 x 9 8 x 14 2in WONT ees hee OP DE atl TS Gk ee 6 5 kg 14 31b CONSTRUCTION Housing DU D TIL steel and aluminum THERMAL Exterior surface temperature under steady state condition 100 C 212 F Time required to cool before handling
8. f AC power that complies with local building and electrical codes and has both overload and ground fault protection Note If the external power cord of this luminaire is damaged it shall be replaced by a special cord exclusively available from your Martin dealer Configuring for local mains power The Mania EF3 has a switch selectable power supply that can operate in the following voltage ranges at 50 60 Hz 115 120 volts setting 115 220 240 volts setting 230 Warning Do not operate the fixture on a power supply that falls outside of these ranges Select the operating range using the red AC supply switch at the rear of the fixture AC supply setting Installation Installing a plug on the mains lead Warning Important Warning For protection from dangerous electric shock the fixture must be grounded earthed The AC mains supply shall have overload and ground fault protection Verify that the feed cables are undamaged and rated for the current requirements of all connected devices before use The fixture s mains lead may require a grounding type cord cap that fits your power distribution cable or outlet Consult a qualified electrician if you have any doubts about proper installation Following the cord cap manufacturer s instructions connect the appropriate wires to ground earth live and neutral The following table below shows some common wire identification schemes Function Wire EU W
9. hment point on the fixture 6 Loosen the swivel locks tilt the fixture to the desired angle and retighten Swivel locks 7 Verify that the fixture is atleast 1 meters 3 3 ft from the surface to be illuminated and at least 0 3 meters 1 ft from any combustible materials Verify that the clearance around the air vents is at least 0 1 meters 4 in Installation OPERATION 10 The lamp will light when the power on off switch at the back of the fixture is turned on To achieve optimal results the use of smoke effects together with your Mania EF3 is recommended SETTING THE TRIG MODE Use the switch on the back of the fixture to set it to Auto or Music trig mode g WM Trigger mode switch Power on off switch In Auto Trig mode trigger signals are generated randomly This will result in a dynamic light show that runs constantly and does not require music to trigger it In Music Trig mode the built in sensor will generate trigger signals as a result of sounds that it picks up This will result in a dynamic light show that is synchronized with a music beat Mania EF3 user manual THE GOBO WHEEL The Mania EF3 contains the gobo wheel illustrated below A set of dichroic colored filters is mounted on the gobo wheel The two open gobo apertures A and B feature textured effects Gobo wheel rotation is activated and deactivated using the gobo wheel rotation switch The wheel will stop when the
10. ical path The exterior of the fixture can become hot Allow the fixture to cool for at least 20 minutes before handling Do not operate the fixture if the ambient temperature T4 exceeds 40 C 104 F Do not stare directly into the light Never operate the fixture without all lenses and covers installed an unshielded lamp emits dangerous UV radiation that can cause burns and eye damage Introduction 5 Preventing injuries due to falls When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Block access below the work area whenever installing or removing the fixture UNPACKING The packing material is carefully designed to protect the fixture during shipment always use it to transport the fixture The Mania EF3 comes with the following 3 wire IEC power cable User manual MANIA EF3 OVERVIEW Mounting bracket Swivel locks Safety wire attachment AC supply setting 9 ea dE Fuse holder Power on off switch Mains socket Thumb screw cover lock 6 Mania EF3 user manual INSTALLATION AC POWER Before operation ensure that factory setting of voltage and frequency match local power supply Always ground earth the fixture electrically Use only a source o
11. ines or masks placed in a light beam to create different patterns Six gobos are colored and two are textured effects The mirrored reflector shoots 18 colored light beams through the gobos for dynamic light effects that can be run constantly or synchronized with a music beat SAFETY INFORMATION This product is not for household use It presents risks of lethal or severe injury due to fire and heat electric shock and falls Read this manual before powering or installing the fixture follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture If you have questions about how to operate the fixture safely please contact a Martin distributor for assistance Refer any service operation not described in this manual to a qualified technician Do not modify the fixture or install other than genuine Martin accessories and upgrade kits Refer servicing to qualified personnel Maximum ambient temperature T4 40 C 104 F See serial label for replacement fuse size and lamp type Suitable for mounting on normally flammable surfaces Do not look directly into the light Risk of fire electrical shock and burns Use only in dry locations For indoors use only Mania EF3 user manual Do NOT block exhaust vents Shields lenses or ultraviolet screens shall be changed if they become visibly damaged to the extent that their effectiveness is impaired for example by cracks or deep scratches
12. ire US live brown black neutral blue white ground yellow green green Applying power Connect the mains power cable to the fixture at the 3 prong IEC male input socket at the rear of the fixture SS Mains socke Power on off switch Turn the lamp on using the power on off switch OVERHEAD MOUNTING The Mania EF3 is designed to be hung overhead with a clamp not included Block access below the work area before proceeding Mania EF3 user manual Always use a secure means of secondary attachment such as a safety wire For indoors use only To hang the Mania EF3 on an overhead support 1 Verify that the structure can support at least 10 times the weight of all installed fixtures clamps cables auxiliary equipment and other items 2 If hanging the fixture with a rigging clamp verify that the clamp is undamaged and is designed for the fixture s weight Bolt the clamp securely to the mounting bracket on the fixture with a grade 8 8 minimum M12 bolt and lock nut or as recommended by the clamp manufacturer through the clamp hole in the mounting bracket 3 If permanently installing the fixture verify that the hardware not included and mounting surface can bear at least 10 times the fixture s weight 4 Working from a stable platform clamp or fasten the fixture to the structure 5 Install a safety cable that can hold at least 10 times the weight of the fixture through the safety cable attac
13. ponents Clean the optical components regularly The presence of smudges or dust on optical surfaces can reduce the strength of the light output and the quality of the effects Use care when cleaning optical components and work in a clean well lit area The coated surfaces are fragile and easily scratched Do not use solvents that can damage plastic or painted surfaces 1 Disconnect the fixture from power and allow it to cool for 20 minutes Basic service 13 Warning 14 2 Remove the thumb screw holding the cover in place Thumb screw 3 Slide the fixture cover open as far as possible there is a physical stop point that prevents access to the power supply section 4 Vacuum or gently blow away dust and loose particles with compressed air 5 Remove stuck particles with an unscented tissue or cotton swab moistened with glass cleaner or distilled water Do not rub the surface lift the particles off with a soft repeated press 6 Remove smoke and other residues with cotton swabs or unscented tissues moistened with isopropyl alcohol A commercial glass cleaner may be used but residues must be removed with distilled water Clean with a slow circular motion from center to edge Dry with a clean soft and lint free cloth or compressed air 7 Closethe fixture cover and tighten the thumb screw taking care not to trap any loose wires LAMP MAINTENANCE Isolate electrically before re lamping The lamp shall be changed if it b
Download Pdf Manuals
Related Search