GANZ MPEG-4 Encoder Web Page V2 User`s Manual
Contents
1. How to register Motion Detection Step 1 Select a video channel from the combo box of Image Source and press Play button Step 2 Select Layer from the combo box of Motion Enable Layer ID Step 3 Tick the checkbox of Motion Enable Layer ID Step 3 Right click anywhere on the screen to make a Area Step 4 Adjust the size of Areas by dragging in and out of the edge Step 5 Put Threshold value and Activity value between 0 and 255 Step 6 Press SAVE and RUN button for testing the motion detection You can set Layer up to 3 and each layer can have up to 8 areas The Object size and Sensitivity values of each Layer applies to all of the areas in one Layer Terminology of ObjectSize and Sensitivity are as follows e Sensitivity sensitivity of each macro block 16 x 16 pixels e Objectsize proportion of the exceeded Sensitivity of macro block in the Area e The Value of Sensitivity and Objectsize ranges from 1 to 255 and a lower figure means the higher sensitivity 28 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual In case of Kernell6Xnmn it supports only one Area even if you set several Areas Note 4 4 3 Event Settings How to register Event Please refer to the step 1 2 and 3 ZN S4000AE nto Single View MultiView Setup P Video Event Confiquration Audio Network Y Event Add Motion Ewent blo dify Event Server Record System 10 Step 1 1 Click Add2. examples below To view 2 stream rtsp 192 168 29 23 555 multicast To view 3 stream rtsp 192 168 29 23 556 multicast To view 4 stream rtsp 192 168 29 23 557 multicast 21 2010 2 1 M 1 4 34 GANZ MPEG 4 Encoder Web Page V2 User s Manual DDNS Settings ZN S4000AE e SingleView MultiView Setup Video DDNS Configuration Audio Server Enable NO vi Network Server Type DynDNS v Address id General User ID Ei userPassWort gt Multicast DNS Name DDNS Update Time po pos Port IP Type REAL v b Event gt System 10 For DDNS configuration setup you must visit dyndns com ahead and make an account for DDNS service Server Enable Select YES to use DDNS Server Type DynDNS No other settings allowed Address www dyndns com No other servers allowed User ID your user ID created at the Dyndns com User PW your password registered at the Dyndns com Case sensitive DNS name your dynamic domain host server name Update time Specify how often GANZ Encoder and Network camera check the dynamic domain server unit minutes Port Default value is 1 This means the DDNS feature is disabled as a default If you use DDNS you can type the required port number for DDNS IP Type Real Local Real represent that the device s public IP seen by DDNS server will be registered to the DDNS server If you select Local private IP of
3. If your GANZ Encoder and Network camera model doesn t support DI and DO this configuration part is disabled with gray Please check out the specification of DI DO of your model 44 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 3 PTZ ZN S4000AE Er singleView l Setup PTZ Configuration P Video Enable PtzDriver Addr CommPort D 1 mz a t I ie Network PTZ2 None wE b Event EA PTZ3 E v 1 1 P Record PUN PTZA E we Mi vi serial Port Setting DDO PTZ External Video Out PTZ protocol options are shown in the drop down combo box and you can choose a protocol you want per video channel 1 Check Enable in the check box and choose the protocol you need 2 Set the Addr and CommPort 3 Click Apply button PtzDriver Select the protocol you want to use from the list Addr Y ou should set the Addr value according to the ID you set by dip switch of PTZ camera CommPort 0 1 O means RS232C 1 means RS485C 45 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 7 4 External Video out Setting ZN S4000AE ue SingleView MultiView Setup ROO Video Out Audio Select b Network gt Event Video Loopback gt Record 0 1 No v gt System 2 3 No v S Serial Port Setting DIDO PTZ External Video Out This page provides the external video output setting and video loopback function setting The video lo
4. 3 VIN2 SINGLE Loop out Encoder 4 QUAD SINGLE Dual stream of ZN SA000AE 47 GANZ 2010 2 1 M 1
5. Higher figure setting moves the image to the upside direction It ranges from 4 to 4 Copying an image to shared memory Let the NVE IP memory make the best use of the source When GANZ Encoder works with the data from camera like a recording or FTP upload the data copied on the shared memory is used for this When you don t need a recording or FTP upload etc just disable this feature and the image copying process is omitted and it helps to reduce the load Deinterlace Mode You can enable or disable the deinterlacing mode by selecting YES or NO in the box 15 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 2 Audio Setup The audio setting page provides the options for the audio input and the audio output 4 2 1 Audio Input Settings ZN S4000AE e SingleView MultiView Setup P Video video 1 video 2 video 3 video 4 Y Audio Audio Input Configuration Audio Input D Enabled YES v Audio Output Stream Type Pem v Network Sample rate 16000 v Event Data bit 16 we gt Record Gain 128 0 255 P System Li NOTE If your GANZ Encoder and Network camera model doesn t support audio input this configuration part is disabled with gray Please check out the specification of audio of your model Audio Input Setting 1s required when you want to listen to the sound from the camera site In order to test this feature the microphone should be connected to the audio port of GANZ Encoder
6. Web Page V2 User s Manual 4 5 1 Recording on USB memory stick aX Caution ZN S4000AE When you remove the USB memory stick from GANZ Encoder and Network camera series after recording Before you remove the USB memory stick change the USB Mount value to No first Or the recording may not work properly even if you inset the memory again when you need to record If you have a problem as mentioned above please reboot the GANZ Encoder and Network camera series and then try recording again then it will work fine CAP http SingleView MultiView Setup P Video P Audio Network b Event Y Record Record USB Data Preparation before recording Record Configuration Record Enable Port USB Mount Record Recycle Default File Size video 1 video 2 Recording Record Device Record Mode FTP Server PostTime Skip Frame Record Frame YES 2100 100 10000 YES W Rotate Ww Mbyte video 3 video 4 yes record stop USB Passive hd sec D Step 1 Insert the USB memory stick to the module of GANZ Encoder and Network camera series Step 2 Go to the Web Page gt Set up gt Record and set the value of USB Mount to YES as above Step 3 Select USB for the value of Record Device Select which recording mode you want between Passive mode and Schedule mode For details 33 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual refer
7. completed 24 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual ZN S4000AE bay SingleView MultiView Setup Event server Video 7 FT FromEmail bn cles gt Network MailServer mailudptechnology con Y Event MailServer port 25 base port 25 Motion ID test Event Password eee Event Server x gt System 10 FromEmail E mail address of a sender MailServer1 SMTP server address MailServer1 Port SMTP server port number default port number 25 ID Type the ID of the sender s mail account Password Type the password of the sender s mail account Case sensitive 4 4 1 2 FTP Server Settings How to resister FTP server Step 1 Press Add FTP button Step 2 Then you can see the screen below Step 3 After filling in the blanks press Add button and Ok is popped up Step 4 Adding FTP server is completed 25 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual ZN S4000AE SingleView MultiView Setup Event FTP server Name Address Port 21 base port 21 Motion User ID Event User PW Event Server Upload path gt d timeout 100000 microsecond 2 Name Random name for FTP server Address IP address or domain name of FTP server NOTE Domain name is supported at firmware K641 13410 or higher Make sure if the DNS setting i
8. to the explanation below How to record video NOW Passive mode Step 1 Set the Record Enable as YES Step 2 Set the Record Mode as Passive Step 3 Type the port number and Record Recycle e Port number Used for playback and 2100 is set as the default e Record Recycle Rotate lets the new files overwrite existing files when USB memory is full None lets the recording stop if the USB memory is full Step 4 Set the PostTime with second unit If you want to record for 30 minutes type 1800 for the value of PostTime and then the recording will continue for 30 minutes on pressing the Record button Step 5 Set the Skip Frame and Record Frame with referring to the explanation and examples below e Skip Frame This 1s to set the number of frames to skip between Record Frame Refer to the examples below e Record Frame This is to set the number of recording frames For example if the value is O only 1 frame is recorded every time after skipping the number of skip frame you set above e g If you set 149 for Skip Frame and O for Record Frame with FPS 30 you will get 1 frame per 5 seconds e g If you set 5 for Skip Frame and 1 for Record Frame with you will get the frames as below 112 8 4 5 6 7 8 9 10 11 12 19 Recording Frame Skip Frame Step 6 Click Record button and then the recording starts How to record on SCHEDULE Schedule mode If you want to record the video according to the specific date and time p
9. 1 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual Available frame rate NTSC 30 15 7 5 10 6 3 75 2 1 PAL 212 58 0 29 5 4 5 1 Bit rate mode CBR VBR and HVBR are supported The default mode is CBR If you set as HVBR both Bitrate and Quant values can be set Bit rate Type a bitrate in the Bitrate box The default value 1 5Mbps Only when the bitrate mode is CBR or HVBR it s adjustable The range is from 32 Kbps to 10Mbps i Since the maximum bitrate is 10Mbps in case of multi channel device such as ZN S4000AE you should distribute the bitrate within 10 Mbps Note Quant Type a quant value in the Quant box The default value is 128 This 1s available only when the bit rate mode is VBR The range is from 0 to 255 Quant value is related to the image quality of VBR setting The lower value makes high quality images GOP Size Select a GOP size in the GOP box GOP is an abbreviation of Group of Pictures and its number means I frame interval If GOP size is 1 totally only I frame is generated in 1 second and if 15 is set 15 frames are captured per 1 second Users can select a number from 1 to 255 and the default is 15 Brightness Saturation Contrast Hue The range of each value is 0 to 255 and default value is 128 Hue adjustment limitation If your item is one of the GANZ MPEG 4 Network Camera series or ZN SIOOAE with PAL video format Hue value adjustment doesn t work at all This is
10. GANZ MPEG 4 Encoder Web Page V2 User s Manual fh MPEG 4 Encoder series 3 WebPage V2 N T SW RR User s Manual ODO GANZ MPEG 4 Encoder Web Page V2 User s Manual Table of Contents 1 Introduction C 5 2 Connection 6 2 1 Access to web Dage e e enn 6 2 2 ActiveX installation UMC cab e HMM 7 3 Main page Configuration eeeeeeseeeeeeeeeeeeeeeeeeeeeeeeeeeeoeeeeoeeeeoeeeeeeeeeoecoreseoeeeeoreeeoreseeroseoreseeeeeeoreseoeesee 8 3 1 Single Va LEE 8 X Mol VIEWS A IA ISA AAA ISA TAO 0 3 3 Setup ass 0 4 Setup Configuration nennen nnne enne enne tne nennen nennen tnos eet enenen eet n nene eate 10 4 1 Video Setup AAA eed nate sa euo dU Toe E Tes Suo dE eed pod oa eue DU AAA 11 4 1 1 Video Settings eene 1 4 12 OSD Settings A SEES SEES SEES SS eub ERU d SES SE SEERNES Ua pis 13 2d 3 ASI ADA AS AAA ARAS AAA AAA AA AAA 15 42 Audio Setup RR 16 4 2 1 Audio Input Settings sais Ss Vasile ER 16 4 2 2 Audio Output Settings ES IZ 4 3 Network Setup iones o boa DNI evans sia enews Oe nas 18 4 3 1 General Settings r X E ESS 18 4 3 2 QoS Settings EE 19 4 3 3 Multicast Settings E A OA NO T Vals 20 4 3 4 DDNS Settings RR ASADA ADE AAA ASA ASAS AAA AAA 22 4 3 5 Advanced Settings a UR AE OA 23 A 4 Event Setup AA A o 24 4 4 1 Event Server Settings ERA RR re 24 4 4 1 1 SMTP Server Settings E SEE SS SSD SENSE o 24 4 4 1 2 FTP Server Settin
11. NZ Encoder and Network camera series but some parts of Ul are described on the basis of ZN S4000AE 4 channel network encoder model And for more detailed specification of your model refer to the hardware manual or specification sheet GANZ MPEG 4 Encoder series List ZN S100AE ZN S1000AE ZN S2000AE ZN S4000AE ZA NVE 12K ZA NVE 40K GANZ MPEG 4 Network Camera series List ZN D310AE series ZN DT350AE series ZN DNT350AE series 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 2 Connection 2 1 Access to web page How to find the IP address of your products 1 MAC address you can find out the default IP address of your product from MAC address if you do not change IP address For the detailed instruction for this please refer to GANZ MPEG 4 Encoder Hardware Manual eng pdf How to connect to GANZ Encoder and Network camera web page With Typing Type IP address of the product you want to connect in the address bar at Internet Explorer directly Then you can see the log in message pop up and a window With Utility ZNS GIT IPAdminTool is provided for IP searching and management For the detailed instruction for this please refer to ZNS GIT IPAdminTool User s Manual Eng pdf If you connect to the web page and log in for the first you can see the window below 2 HVE4000 Ver Windows Internet Explorer E Htpi 192 160 230 L06 enc Ca view iuto Ca hebes Aan herd fle dk Wem Fgrortes Io Heb Wwe F
12. and Network camera unit Refer to the hardware manual for the connection Enable Enable or disable audio input Name Type a nickname for the audio input Stream Type Select audio input format PCM uLaw and aLaw are supported Sample Rate Select sampling frequency 16KHz 8KHz are supported Data bit Select bit per sample If the stream type is PCM 8bit and 16bit are available If the stream type is aLaw or uLaw only 8bit is available Gain Gain ranges from 0 to 255 and default value is 128 16 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 2 2 Audio Output Settings ZN 54000AE hs SingleView MultiView Setup Audio Output Configuration Name E Audio Input stream Type PCM el Sample rate 16000 Audio Output i Data bit 16 e ik KS ceo Gain 0 255 Save NOTE If your GANZ Encoder and Network camera model doesn t support audio output this configuration part is disabled with gray Please check out the specification of audio of your model Audio Output Setting is required when you want to talk to people near the camera Configure the values and click the Save button and it enables your PC to send the voice to the speakers of server In order to test this feature the microphone should be connected to the audio port of your PC so that you can talk to Likewise the speakers should be connected to the GANZ Enco der and Network camera series Refer to the ha
13. because of the characteristic of the decoder chip built in GANZ MPE Note G 4 Network Camera series and ZN S100AE If your video format is NTSC it has no problem in hue value adjustment 12 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 12 OSD Settings SingleView MultiView Setup MISSE video 1 video2 video 3 video 4 Video Setting OSD String Configuration Enabled NO OSD Setting den No iw Color 255 0 255 imi String esa J Max32byte X 0 Max 44 Y Max 29 OSD Time Configuration Enabled YES w Format MM DD YYYY hh mm ss v x ca The coordinate value of OSD is absolute points and it is subject to image resolution As the OSD function is processed in burnt in Text method the text is integrated in raw video data before compression NOTE The coordinate value of OSD is absolute points and it is subject to image resolution Because of this reason if your OSD setting position is not different as you expected adjust the image resolution OSD String Configuration Enable If you want to enable string OSD select Yes in the Enabled box Or select No Color Grey scale color from 0 to 255 255 means white and O means black This value applies to OSD Time as well String ASCII character string The maximum length of OSD text must be less than 256byte X Y Type the location of string by number Coordinates of string For example if you set as 0 0 the time stamp wi
14. button to create an event 2 Then you can see the screen below and fill the information in the blanks 3 Click Add and if you see Ok sign it shows event is completely added CAP ZN S4000AE al SingleView MultiView Setup P Video Event Configuration gt Audio Name sd P Network Event Type Event Hardware Mode po 1111 0000 xxxx Motion Software Mode BOOT v MD Event Video Loss Event Server Image Number gt Record Trigger Interval 00 00 01 pem gt System Name Type random name of the event Event Type e Software signal of device boots motion detection and video losses etc e Hardware signal of D I activation such as Sensor 29 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual Hardware Mode If the event type is a hardware type this control is enabled Nnnn where n x 1 x do not trigger 1 trigger on activation For example 1xxx means to trigger when first D I is activated Ixx1 means to trigger when the first and fourth D I are activated Software Mode Select an event mode among motion detection video loss and boot Motion Detection Event is signaled when the motion is detected Video Loss Event is signaled when the video loss is disconnected or connected BOOT Event is signaled when the system is rebooted MD Enable only if software mode is Motion detection To set the MD value press View CGI button on Motion sett
15. complete system rebooting It will take about 110 sec Windows Internet Explorer Do you really want to restart device Cancel 2010 2 1 M 1 42 4 7 IO Setup GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 71 Serial Port Setting SingleView MultiView Setup Video RS232 RS485 pM RS 485 Configuration gt Network Baudrate 9600 X icm Databits 8 v Parity none Record Flow Control none v gt System Stopbit 1o I0 You should reboot the device for applying the new serial configurations Serial Port Setting DIDO PTZ External Video Out Save This page provides the configuration of RS 232C and RS485 You can select one of the value from the list but the value settings on the picture above are default and normally recommended Databits 8 Parity none Stopbit 1 4 7 2 DI DO Setting ZN S4000AE Video p Audio gt Network gt Event Record p System IO Serial Port Setting DIDO ae PTZ External Video Out Baudrate 9600 Flow Control none CAP http SingleView MultiView Setup DI State DIO DI DI2 DB DO State amp Control poo O 001 O 002 O 003 O You can set and get the information of DI and DO For ZN S4000AE each 4 channel of DI and DO are provided This webpage is refreshed every3 seconds for checking up DI DO status 43 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual NOTE
16. d you got from the service provider Note You can find the default network status of GANZ Encoder and Network camera using Z NS GIT IPAdminTool exe or MAC address Refer to ZNS GIT IPAdminTool user s manual or GANZ Encoder and Network camera Hardware manual for detailed information 18 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 3 2 QoS Settings ZN S4000AE a SingleView MultiView Setup Video QOS Configuration gt Audio Video DSCP Ce Network Audio DSCP 0 255 pl Event DSCP bo 0 255 QOS Setting ES Multicast DDNS Advanced gt Event gt Record gt System gt I0 NVE IPE uses DSCP model for implementing QoS Video audio and event classes are available for that What is DSCP It is short for Differential Services Code Point which is a field in the header of IP Packets for packet classification purposes Video DSCP DSCP of video packet Audio DSCP DSCP of audio packet Event DSCP DSCP of event packet DHCP values should be specified in decimal number converted from original 6 bit binary digit Default value is 0 which means 000000 for DSCP value To set the device available of supporting Expedited Forwarding the recommended value for DSCP is 46 101110 19 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 3 3 Multicast Settings ZN S4000AE a SingleView MultiView Setup Ch 1 Ch 2 Ch 3 Ch 4 Multicast Configurat
17. device will be registered i Note Only one dynamic host name is saved Note 22 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 3 5 Advanced Settings ZN S4000AE e SingleView MultiView Setup Video Port Configuration gt Audio RTSP Port Y Network Web Port General User RTSP Port PortForward You should reboot the device for applying the new network configurations QOS Setting Multicast DDNS Advanced P Record bp System re IO RTSP Port This is the port number of first channel for RTSP If a device has more than one channel the port number of next channel succeeds the port number of the first channel For example if the port number of first channel is 554 the second channel would be 555 Web Port This is the port number for HTTP User RTST Port This setting is required ONLY when you have set port forwarding on router device So if your network is not related to port forwarding just leave this User RTSP Port value empty or set same value with RTSP Port as the value means nothing To be more detail about this when port forwarding is done on a network router ActiveX viewer on the client side can t find the port number and ActiveX image may not be seen Because ActiveX is operated only on a client and not able to get the network setting values of GANZ Encoder or Network camera 23 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 4 Event Se
18. dvanced SUS SN Event Y Motion Yv Event Y Event Server Record Y Record v USB Data System System Data System Update User Management PTZ control System Information Reboot SOS NOS IO Serial Prot Setting DIDO PTZ External Video Out OS 10 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 Video Setup 4 1 1 Video Settings ZN S4000AE vd SingleView MultiView Setup Video video 1 video2 video 3 deo 4 Video Selling 2 Image Dd 3 Video Type AUTO v OSD Setting AUTO jas Codec MJPEG v Advanced Resolution 4CIF v bp Audio FPS 2 v gt Network Bitrate Mode CBR w Bitrate bits 32000 10000000 Quant 2s 0 255 gt Record GOP size gt System Brightness 128 0 255 b 10 Contrast 128 0 255 Saturation 0 255 Hue 128 0 255 Video Type Select a type in the Video Type box The video format is detected automatically when the device boots up If you change the video type manually to a certain type it will only affect FPS For example if PAL is set FPS will be changed to 25 fps based one Video Codec Select a codec format in the Codec box MPEG 4 and MJPEG are supported and the default value is MPEG4 Resolution Select a resolution you want in the Resolution box Refer to the table below FPS Frames Per Second Select FPS you want to get in the FPS box This value represents the number of encoded frames you want to get per 1 second 1
19. ence ver p Haced Also to help probect your isty Int Exper toched offer cont fror ZN S4000AE 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 2 2 ActiveX installation UMC cab You need to install ActiveX for displaying images Click pop up blocked and install the Active X control as below 7 HYEASODD Ver Windows internet Explorer KE E E B hi E Le 20 1065 feng ado eg ht rm J ai eae ral HI A B fie ft yew Feie Too H b TOA Bye BD d Eum ib Toots 1 iy Popup Blocked so kn help prokect your security foem E onlenas Hes per content from this ske Click here for options x Por un Blocked Fk SinglaView Mule Setup W Chek Fesa 12 inital the lola Acts control UMC wer 1 1320 hom Tas Co M bore 5 gt ki E oq Internet Explorer Security Warning Do you want to install this software Mame UMC ver 1 3 32 0 Publisher Cap Co More options Install f Don t Install i while Files From the Internet can be useful this File type can potentially harm our computer Only install software From publishers you trust What s the risk If you have failed to install ActiveX follow the next step Delete AxNVE in C WINDOWS Downloaded Program Files and connect again to Web Page so that Active X installer can be downloaded Note Or you can upload ActiveX UMC cab manually with ZNS GIT IPAdminTool the IP management utility Refer to ZNS GIT IPAdminTool user s man
20. gs IS puso 25 4 4 1 3 TCP Server Settings OR NN 26 4 4 2 Motion Detection Settings rr poH PO UN 28 4 4 3 Event Settings A AS 29 4 5 Record Setup n 33 4 5 1 Recording on USB memory CAPA adem died isos 33 4 5 2 Recording OH FLEP SErvera e e e EE Een ete a e de AR Ep EE E VETE E UNE FEET 35 4 5 3 Playback the recoded data in USB device eee 36 4 6 System Setup O E DM Ed E A SEER NEDE SER ERE mI NR 37 4 6 1 System BRI 37 4 6 2 System Update ER SAND UE Ade SD WELL ato V LEA dia AV IA rene reer eee nda 38 4 6 3 User Management eese 39 464 PIZNPiDiucoltssiseessesedussiessyestes veses vexa aane qua au RR VAS NUES NIE VEA AAA 40 4 6 5 System Information ida ara 4 TORO PR EQ CE LI m I 42 4 7 IO Setup ET 43 4 7 1 Serial Port Setting nut etu iso viai alo oS 43 4 7 2 DUDO Setting IN A dequo E ES TE oi side ed S asd qoe seeds 43 LAG Mor AMD A 45 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 7 4 External Video Out Setting eesesesccscsssceceosesesesesosecccccsesceceesesesesecesssececececcececececesecececes 46 GANZ MPEG 4 Encoder Web Page V2 User s Manual 1 Introduction This manual explains how to interface with the GANZ Encoder and Network camera series using a standard Web browser for example Microsoft Internet Explorer The Web Page of the GANZ Encoder and Network camera series is implemented with the HTTP API RTP RTSP and Active X program NOTE Please be notified that this manual should be applied to all of the GA
21. ing page and then you can see the window as below 2 http 192 168 20 106 enc cgifadmin 2 BK aD Internet For example if you set MD as MO it means triggering motion is from Layerl In the same manner M1 means Layer 2 M2 means Layer 3 Video Loss Channel numbers for triggering Image Number Channel numbers to connect with event Trigger Interval 00 00 01 is set as the default value Assume the value is 00 00 05 and it means even if the event happens several times for 5 sec the GANZ encoder will trigger only once per 5 sec 30 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual step 2 1 Go back to the Event tab on the left menu and select the event you created in the box 2 Click Modify button 3 Press the Action button that is created ZN S4000AE nt SingleView MultiView Setup gt Video Event Configuration gt Audio Name gt Network Event Type Y Event Hardware Mode 1111 0000ixxxx Event MD Moca Video Loss Event Server Image Number i wv Record Trigger Interval 00 00 05 hh mm ss System Step 3 1 The screen as below is displayed Select the proper server on the Server list and set the values in the blanks 2 Click Add and if you see Ok sign it shows it s completely added ZN S4000AE nt Singleview MultiView Setup video Event Action Configuration gt Audio _ o MM gt Network Event Actio
22. ion Enabled Video Address General Video Port 6000 ane sene Video TTL Multicast Audio Address DDNS Audio Port Audio TTL Advanced Event Port b Record Event TTL 128 T This page provides the multicast configuration of each channel The addresses mean the group address which is required to receive the each data from the router The values in the boxes are default and you can set the values according to your network requirement How to see the video with RTSP multicast via VLC media player COUDPJRTP CO UDPJRTP Multicast O HTTPIHTTPSIFTP MMS Advanced options Stream Save Settings Caching Customize rtsp f192 168 20 106 multicast e We support only RTSP multicast UDP RTP Multicast 1s not supported in GANZ encoder 1 Enable the Multicast configuration on the NVE Webpage Open the VLC media player and go to File gt Open Network stream then you can see the window above 3 Tick on RTSP tab set the URL of GANZ encoder address as the example above 4 Youcan see the view with RTSP multicast If you want to view channel 2 3 or 4 enter rtsp NVE_IP port number multicast The default port number of RTSP is 554 and it doesn t matter to skip the default port number 554 to view the 1st stream But for other channels add the port number at the end of address like 20 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual
23. lease follow this instruction Step 1 Follow the same steps of How to record Video NOW except for Step 2 34 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual Step 2 Set the Record Mode as Schedule Step 3 Set Record Weekdays Start Time and End Time as the description below e Record Weekdays You can assign days for recording First digit corresponds to Sunday and last digit corresponds to Saturday For example if you set as 0111110 the recording runs only from Monday to Friday e Start Time You can type the time to start recording with 00 00 format e End Time You can type the time to end recording with 00 00 format Step 4 Click the Record button and then the recording starts 4 5 2 Recording on FIP server Step 1 In order to record the video on FTP server FTP server should be added in advance For this go back to the section 4 4 1 2 FTP Server Settings and check out if the FTP server is added to GANZ Encoder and Network camera series properly Step 2 Set Record Device as FTP Step 3 Set Record Mode as you want You can find the difference between Passive mode and Schedule mode on 4 5 1 Recording on USB memory stick Step 4 Set FTP Server number This is available only when you finish the Step 1 For example if you added FTP server name as UDP TEST then you can see FTP F0 UDP TEST screen as below This FO is the value for FTP Server ZN S4000AE SingleView MultiView Setup Eve
24. ll be shown on the top left of image Input range of coordinate value X 0 44 Y 0 29 OSD Time configuration 13 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual If your models are ZN S2000AE ZN S4000AE or any multi channel encoding models OSD time setting 1s available only on the Ist channel and the other channels do not support the Time OSD setting for the systematical reason of Note multi channel models of NVE OSD time is refreshed per 1 second and synchronized with NTP server you can set this System System Data menu Enable If you want to enable time OSD select Yes in the Enabled box or select No Format Select one of the formats you want from the drop down box X Y Type the location of string by number Coordinates of string For example if you type 0 0 the time stamp will be shown on the top left of 1mage Input range of coordinate value X 0 32 Y 0 29 14 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 1 3 Advanced ZN S4000AE var SingleView Setup YF Video video 1 video 2 video video 4 Image Source Confiquration Video Setting i m horizontal delay fo 32 32 OSD Setting vertical delay 4 4 Advanced 3 Copying a image to z YES Pr Audio shared memory Deinterlace Mode P Network P Record System b lO Horizontal delay Higher figure setting moves the image to the left direction It ranges from 32 to 32 Vertical delay
25. n Y Event FE Message Event Eneio Recsvergiriec c SMTP Event Server Subject SMTP gt Record Aa det H 0 0 tyes To enable ImagesPerMail amp FTP go to Video gt Advanced and turn on Copying a image to shared memory to YES and change Video System Codec to MJPEG Event Action The actions you created are listed You can select one of those from the list Server Select the server you want We provide the TCP SMTP FTP DO and USB recording server If the server you want is not shown in this list that means the registration of the server was not successful Go back to the 4 4 1 Event Server Setting section and follow the instruction for server addition 3 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual Message Type an e mail message you want to send as the example above EmailTo Type an e mail address of receiver as the example above Subject Type the subject of e mail as the example above ImagePerMail If you want a captured image with the e mail message type 1 or just insert 0 When you set the values on the page of event action configuration the must set values are different SMTP Set all of the blinks FTP Only server and message are required message can be any words TCP Only server and message are required message can be any words DO No need to fill in USB recording No need to fill in 32 2010 2 1 M 1 4 5 Record Setup GANZ MPEG 4 Encoder
26. nd click Play or Stop button for display control e Delete Select the file you want to remove and click Delete button ZN S4000AE nttp SingleView MultiView Setup USB Record List USB Data pane 36 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 6 System Setup 4 6 1 System Date ZN S4000AE SingleView Setu p gt Video Device Time Tre O gt Network gt Event Date Configuration gt Record TimeZone GMT v Y System Client Time system Date TimeMode e oe O system Update NTP server time nist gow O User Setting sind adi Date 2008 03 08 Time 15 25 27 PTZ protocol It takes about 10 seconds for synchronizing system time with NTP server if changing time mode to NTP server system Information Reboot i Device Time It displays the date and time of GANZ Encoder and Network camera system Time Zone Select your time zone Time Mode You can select a time mode with 3 options and this will be reflected on GANZ Encoder and Network camera system e Client time Synchronized with your current PC time e NTP server Synchronized with NTP server time nist gov is selected as a factory default but you can choose one of them from the list e User setting Users can type time manually as they want 37 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 6 2 System Update ZN S4000AE SingleView Setup Sy
27. nt Server Configuration Event Server Step 5 Set the PostTime with second unit If you want to record for 30 minutes type 1800 for the value of PostTime and then the recording will continue on pressing the Record button for 30 minutes Step 6 Set the Skip Frame and Record Frame with referring below explanation and example e Skip Frame This is to set the number of frames to skip between Record Frame Refer to the examples below 35 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual e Record Frame This is to set the number of recording frames For example if the value is 0 only 1 frame is recorded every time after skipping the number of skip frame you set above e g If you set 149 for Skip Frame and O for Record Frame with FPS 30 you will get 1 frame per 5 seconds e g If you set 5 for Skip Frame and 1 for Record Frame with you will get the frames as below FR poc 3 4 5 6 7 8 9 10 11 12 13 Recording Frame Skip Frame N You must set the video format to MJPEG when you want to use Ftp server for recording Caution 4 53 Playback the recoded data in USB device If you have completed USB recording steps you can check out the recording status If you don t see created file in the Record List it means recording is not completed e Record List Show the created recording files Red line box in the picture below e Play Stop Select one of the files in the Record List a
28. nual 4 6 3 User Management ZN S4000AE es single View Setup Users Configuration Add System Date System Update User Management PTZ protocol System Information Reboot There are two user types provided by default Accounts can be created up to 10 including two default users e ID Up to 32 characters with the combination of alphabet and digits First character must be an alphabet Case sensitive e Password From 3 up to 8 characters with the combination of alphabet and digits Case sensitive How to add a user 1 Click Add 2 Type ID amp password and select security level on User add pop up window 3 Select Add button on User add pop up window 4 Click Close on User add pop up window How to delete a user 1 Select a user to delete in User List 2 Click Delete 3 Click OK on confirming dialog 4 Click Close on Remove user pop up window How to modify a user 1 Select a user to modify in User List 2 Click Modify 2 Modify the password or security level 39 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 3 Select Modify on User Modify pop up window 4 Click Close button on User Modify pop up window 4 6 4 PTZProtocol This page shows the list of current PTZ protocols built in the GANZ MPEG4 Encoder and also you can upload the new protocol as well if your camera is using protocols other than on the GA NZ MPEG4 Encoder web
29. o source And then you can listen to the audio sound e MIC Enable When you want to send the audio through a microphone from your PC to the camera installed site you can enable this And then the audio input from the microphone will be transferred via network NOTE If your GANZ Encoder and Network camera model doesn t support audio output MIC Enable check box will be disabled with gray Please check out the specification of DI DO of your model 3 2 Multi View Multi View shows all channels on one page For example ZN S4000AE displays 4 channels and ZN S2000AE shows 2 channels Play Stop and Snap button work equally as in the Single view NYLAODO Var Windows Internet xplener E hai pe5 23 106 fere eodem mua bg hem entree Pd ZN S4000AE 3 3 Setup This page lets users set all of the values for controlling GANZ Encoder and Network camera series and update the files See the next section 4 Setup Configuration to understand how to set and change the values 9 GANZ 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 Setup Configuration In Setup page you can set or change the values of GANZ Encoder and Network camera series click Setup on the main page of Web Page and you can see the categories as below on the left side of the main page Video v Video Setting Y OSD Setting Y Advanced Audio Y Audio Input Y Audio Output Network General QOS Setting Multicast DDNS A
30. opback is related to the dual stream The dual stream is useful when you want to use one video stream as separate two streams with different video settings image size codec type frame rate and so on Video Out You can choose either single view or multi view of your stream on the external output Ouad displays 4 channels as a quad multi view on the external video out Only ZN S4000AE supports Quad option Switching view displays the selected channel one by one on the external video out Video Loopback J 11 YES NO Enable or disable the video loop back of channel 1 stream 2 3 YES NO Enable or disable the video loop back of channel 3 stream Only ZN S2000AE and ZN S4000AE are available with dual stream use The diagram of single stream mode and dual stream mode as below would help your understanding 46 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual Single Stream Mode CAM 1 VIND Encoder 1 CAM 2 Encoder 2 VIN2 Dual Stream Mode CAM ftl Encoder 1 Network gt I Loop out Encoder 2 VIN2 Network Dual stream of ZN S2000AE Single Stream Mode External Video Out QUAD CAM 1 Encoder 1 Network VIN1 i Uu CAM CAM 2 CAM 2 Encoder 2 VIN2 i CAM 3 CAM 4 CAM 3 Encoder 3 VIN3 IIl i SINGLE CAM 4 Encoder 4 VINA QUAD SINGLE Dual Stream Mode QUAD CAM 1 Encoder 1 Network VIN1 P Unt CAMS CAM I1 Loop out Encoder 2 Eid CAM 2 CAM 2 CAM 2 Encoder
31. ormation MAE 00 13 23 03 1D E0 TIME 2006 08 08 06 12 45 Version Information Bootloader U Boot 1 0 4 jb16m 33 Firmware FW W1 5541 11304 Webpage 241 OCX 1 9 0 20 System Date Dome firmware System Update User Management PTZ protocol system Information Reboot This page shows the system information below The picture above is the example of ZN S4000AB ZN S4000AE Information e MAC MAC Address e TIME Date and time information being applied to the current GANZ Encoder and Network camera system Version Information Bootloader Bootloader version Firmware Current firmware version Webpage Current web page version OCX Current ActiveX version Dorm Firmware This information is shown only when you have just uploaded the dorm firmware on this System Update page And also the works only when your IP product is a dorm camera type If you have not uploaded any dorm firmware with this the version information doesn t appear here 41 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 6 6 Reboot CAP ZN S4000AE bs SingleView Setup System Reboot System Date system Update User Management PTZ protocol System Information Reboot When you want to reboot your GANZ Encoder and Network camera system on the webpage you can reboot it on this page without physical operation Just click OK button and then a pop up window as below is shown It will take about 1 2 minutes to
32. page SingleView MultiView Setup PTZ Protocol Protocol Name FileName Type Version Description American dynamics american_dynamics ptzs built in 1 1 0 0 ERE nica Bosch ltc856x bosch ltc856x ptzs built in 1 0 0 0 Bosch LTC 856x protocol Custom02 custom02 ptzs built in 1 1 2 0 PTZ Protocol Kalatel ascii kalatel ascii ptzs built in 1 0 0 0 Kalatel ascii protocol Panasonic CS850 panasonic CS850 ptzs built in 1 1 0 0 Panasonic WV CS850 protocol Pelco D probe pelco d probe ptzs built in 1 1 0 0 Pelco D protocol for probe System Date Pelco D pelco d ptzs built in 1 1 1 0 Pelco D protocol System Update Pelco P pelco p ptzs built in 1 1 0 0 Pelco P ptz protocol User Management Samsung elec samsung ptzs built in 1 1 2 0 PTZ Protocol for samsung elec Upload PTZ protocol Upload new protocol System Information ne Please refresh the page if the ptz list is not shown properly after uploading or deleting the PTZ driver eboo How to add PTZprotocol manually 1 Click Browse button 2 Choose the required file and click Upload button 3 Ina while you can see the protocol is added on the list If you go to the menu of IO gt PTZ you can choose the PTZ protocol you want Refer to the 4 7 3 PTZ to find out how to apply the newly added protocol to GANZ Encoder 40 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 6 5 System Information ZN S4000AE cae singleView Setup NVE4000 Inf
33. rdware manual for the connection Name Type a nickname for the audio output Stream Type Select audio output format PCM uLaw and aLaw are supported Sample Rate Select sampling Frequency 16KHz 8KHz are supported Data bit Select bit per sample If the stream type is PCM 8bit and 16bit are available If the stream type is aLaw or uLaw only 8bit is available Gain The range of each value is 0 to 255 and default value is 128 17 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 3 Network Setup 4 3 1 General Settings 2 http 192 168 20 177 setup html Windows Internet Explorer m EJ gt DS le http 192 168 20 177 setup html File Edit View Favorites Tools Help y s a p dh htep 192 168 20 177 setup html e o ih i Page Of Tools ZN S4000AE SingleView MultiView Setup IP Address Configuration Network mode static Ww IP address 192 188 20 177 Subnet mask General Gateway DNS Server Multicast PPPoE ID QOS Setting DDNS PPPoE Password Advanced e Internet IP Address Configuration If IP configuration is DHCP IP address Subnet mask gateway and DNS are received from a DHCP server If IP configuration is STATIC you have to input the IP address Subnet mask gateway and DNS manually as IPv4 format e g 192 168 18 96 If you want to use PPPoE feature type the PPPoE ID and passwor
34. s enabled to use domain name of FTP server Port Port number of FTP server between 0 and 65535 User ID User PW FTP Server log in ID and Password Case sensitive Upload path Type the path of uploaded files For example home Timeout Timeout value for FTP connection and data transfer Unit Us Default value is set as 100000 0 1 sec but you can change it as you want 4 4 1 3 TCP Server Settings How to resister TCP server Step 1 Press Add TCP button Step 2 You can see the screen below Step 3 After filling in the blanks like above press Add button and OK is popped up Step 4 Adding TCP server is completed 26 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual ZN S4000AE E SingleView MultiView Setup Event TCP server Video ian LL Audio P Network Y Event Motion Event Event Server Record E 10 Name Random name for TCP server Address IP address of TCP server as Ipv4 Port Port number of TCP server between 0 and 65535 2010 2 1 M 1 27 GANZ MPEG 4 Encoder Web Page V2 User s Manual 4 4 2 Motion Detection Settings If you completed setting Event Server move to the Motion tab on the left for setting the motion detection function ZN S4000AE SingleView MultiView Setup Image Source wee x Motion Event Event Server O Motion Enable Layer ID isve v ObjectSize 128 Sensitivity 128
35. stem Update i Browse O Force update Current Version System Date Bootloader U Boot 1 0 4 b16m 33 Firmware FW V1 5 641 System Update Webpage 240 OCX 1 9 0 20 User Management Dome Tirmware PTZ protocol System Information Reboot This page is required when you want to update another version of software such as bootloader firmware webpage OCX or Dome Firmware However for more various update function and system information ZNS GIT IPAdminTool exe is more recommended as this utility is made for the purpose of managing the IP products in more user friendly way Refer to the ZNS GIT IPAdminTool user s manual provided in the SDK System Update You can upload firmware files and update your GANZ Encoder and Network camera Click the Search button and choose the file you want to upload After that click the Upgrade button In a while you can see the updated version information in the Current Version as below Current Version Bootloader Current bootloader version Firmware Current FW version Webpage Current Webpgae version OCX Current ActiveX version Dorm Firmware This information is shown only when you have just uploaded the dorm firmware on this System Update page This works only when your IP product is a dorm camera type If you have not uploaded any dorm firmware with this the version information doesn t appear here 38 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Ma
36. tup This manual assumes that Motion Detection is an event for GANZ encoder action trigger So consider this carefully and follow the setting step as the order below If your event factor is not Motion Detection you can just skip Step2 Motion setting Step 1 Event Server setting Step 2 Motion setting Step 3 Event setting relate the event setting and motion detection setting you set GANZ encoder series support SMTP TCP and FTP server as an event server Seeing the left menu of Event you can find the Motion Event and Event Server tabs To apply this event function on GANZ encoder it is recommended to set Event server first and move to Motion setting Ahead of event server setting the setting as below should come first e Goto the Video gt Advanced menu on the left of this page and turn on Copying a image to shared memory to Yes and change the codec value Caution as MJPEG at Video Codec menu 4 4 1 Event Server Settings ZN S4000AE ue SingleView MultiView Setup Event Server Configuration SMTP Event Server Motion Event Event Server gt Record gt System IO 4 4 1 1 SMTP Server Settings How to register SMTP server Step 1 Click on the written character SMTP in the box and press Modify button on the right Step 2 Then you can see the screen below Step 3 After filling the blanks as below press Add button and Ok is popped up Step 4 Adding SMTP server is
37. ual pdf 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual 3 Main page Configuration 3 1 Single View Single View shows only one channel on a page Video I is set as the default channel and other channels are chosen from the drop down combo box NVE4000 Ver Windows Internet Explorer ZN 54000AE EJ Motion View EJ Osd View EJ Audio Enable C MIC Enable e PLAY and STOP button Play or stop current channel view e SNAP SHOT button Save the snap shot of current video image The file is saved in My Documents Snapshot folder Snapshot is available only when the codec type is set to MJPEG format Note e Full Screen button Shown with full screen e PTZ button Virtual PTZ control keyboard pops up This is used to control PTZ IP camera products only PTZ Windows Internet Explorer m http 192 168 20 106 enc cgifviewfauto cgi html fptz ht Y kiki PRESET TOUR 41516 PTRN SCAN kA 8 9 MENU GLOBAL cur ME CTRL HOME og E Internet 2010 2 1 M 1 GANZ MPEG 4 Encoder Web Page V2 User s Manual e Motion View When the motion detection is set on Event menu you can see the detection status on the current image screen e OSD View Shows the current image information RTSP address Channel number FPS Frame type Frame Size Date and time on the image view screen e Audio Enable To enable this function the audio connection cable should be connected to IP Products from the vide
Download Pdf Manuals
Related Search