RED ROCK OD ROD-1 - Providence
Contents
1. Remove the 4 screws from the back cover to replace the battery Use a 9V 6F22 MN1604 type replacement battery When changing the battery do not pull strongly on the battery cable This could result in disconnection or malfunctioning of the device Caution When connected to an amp and speaker with the power turned on do not insert or remove plugs in the input or output jacks Doing so may cause sufficient noise to damage the speaker Jf the pedal should fail to work or if it works abnormally please contact the place of purchase or Pacifix Ltd Jf the pedal is not used for an extended period of time please remove the battery to prevent leakage which could damage the pedal A battery should be inserted into the pedal even when using an AC adaptor By doing so if the AC adaptor plug should be inadvertently disconnected power will continue to be supplied by the battery to provide uninterrupted performance An AC adaptor with a regulator circuit is recommended f the battery voltage becomes too low the pedal effect may become weak the output level may drop or no sound may come out of the pedal In that case please replace the battery with a new one Troubleshooting If the indicator LED does not light Replace the battery with a new one or connect an appropriate AC adaptor X Designs and specifications are subject to change without notice PACIFIX LTD SOUND PRODUCT amp SYSTEM DESIGN 3 21 7 Tsurumi Chuo Tsurumi ku Yokohama sh2. Povidence RED ROCK OD roD OWNER S MANUAL Thank you for choosing Providence In order to take full advantage of the product s features and performance please read this manual thoroughly and keep it in a safe place for future reference Main Features Warm overdrive with plenty of sustain gives guitarists a wide ranging expressive voice The tone is a perfect match for guitars with single coil pickups An extra pre gain circuit and three level controls VOLUME GAIN and MASTER make it possible to create distortion effects ranging from crunch to hard drive with subtle control over all nuances in between The pre gain stage and volume control are similar to guitar amp input circuits allowing level compensation for pickups of differing output as well as boost before the signal reaches the overdrive circuit Specially voiced tone control circuitry maintains optimum overdrive sound throughout the control range Internal circuitry doubles the 9 volt supply voltage to 18 volts achieving wide dynamic range with impressive projection and a sense of unlimited depth In conventional true bypass circuits the guitar signal passes through two sets of switch contacts when the effect is bypassed The ROD 1 features an S C T Single Contact True bypass circuit in which the signal only passes through one set of contacts in bypass mode This increases reliability while maintaining the highest possible sound quality at all times Improv
3. ed output jack grounding is achieved with a D C G Double Contact Ground circuit that contacts the mono plug ground sleeve at two points rather than one Increased ground contact area minimizes intermittent connections while ensuring maximum sonic quality HControls and Connectors VOLUME Adjusts level at the pre gain stage MASTER Adjusts the level of the signal output at the OUT jack TONE Adjusts full range tonal balance Turn clockwise to emphasize the midrange and add edge to the sound Low frequency compensation is applied at the same time to prevent the sound from becoming thin Turning this control clockwise also increases overall level Use the MASTER control to compensate as 2 D necessary GAIN Adjusts the amount of distortion produced FAT Boosts the low frequency range when engaged Flip the switch upward to boost the lows LED Indicator Lights when the effect is ON The LED will start to dim when the battery voltage drops below approximate ly 7 volts The effect will still function when the LED begins to dim but performance may not be optimum and the battery should be replaced as soon as possible VOLUME IN The output from a guitar electronic musical instrument or preceding effect pedal should be connected here i z OUT This jack should be connected to the input of an amplifier or effect unit Footswitch Turns the effect ON or OFF WDC 9V IN Connector T
4. he DC output from the AC adaptor should be connected here l Important The VOLUME and GAIN controls are designed to provide high maximum gain When both controls are set higher than their 12 o clock middle positions saturation will occur and noise may increase Oscillation may occur when the maximum settings are approached For optimum performance when one of these controls is set higher than 12 o clock the other should be set to below 12 o clock RED ROCK OD D ovidence 2 z e3 A69 A Standard Drive W iClassic Hard Drive MiLight Crunch MASTER GAIN MASTER GAIN MASTER GAIN TONE VOLUME FAT t VOLUME ON VOLUME FAT y Oy OY MASTER 12 o clock GAIN 10 o clock MASTER 12 3 o clock GAIN 3 o clock MASTER 3 o clock MAX GAIN MIN VOLUME 3 o clock FAT SWITCH OFF VOLUME 10 o clock FAT SWITCH ON VOLUME 11 o clock 1 o clock FAT SWITCH OFF TONE 10 o clock TONE MAX TONE 1 2 o clock BLOCKDIAGRAM GAIN BUFFER PRE GAIN Lo BOOST CLIPPER FILTER BUFFER INPUT ee P OUTPUT VOLUME FAT GAIN TONE MASTER Specifications Controls VOLUME MASTER TONE GAIN FAT vJacks Standard 1 4 inch phone jacks Input Output DC9V Input jack AC adaptor jack Power 9V battery AC adaptor Power consumption DC9V approx 20mA with effect turned ON Size 115 D x 73 W x 50 H mm Weight Approx 250g without battery installed Battery Replacement
5. i JAPAN 230 0051 TEL 81 45 510 4060 FAX 81 45 510 4061 7 E mail overseas1 pacifix Itd com URL www providence Itd com PPD 1403 02 Rev 1 0
Download Pdf Manuals
Related Search