3. Installation and Connection
Contents
1. All are attached to the imager head in the same manner Hold the accessory and the imager head as shown in Fig 8 Screw the thread part of the accessory over the imager head and then fix the accessory as shown in Fig 9 Fig 8 Fig 9 3 3 Micro SD card Installation NOTE Micro SD card slot provides for additional memory but Micro SD card is optional and not included Different Micro SD cards can be used to insert into the Micro SD card slot The maximum 16 GB of the Micro SD card can be supported 10 www obd2express co uk To insert a Micro SD card into the Micro SD card slot make sure the contacts are facing towards slot and the angled portion of the card is facing down When the Micro SD card is installed a small Micro SD card icon will appear at the top right portion of the screen To remove a Micro SD card gently push the Micro SD card inward and then release to eject it from the card slot 3 4 USB Cable Connection Use the supplied USB cable to connect the tool to a PC to upload and view captured photos and videos A USB Connected message will appear on the screen as shown Fig 10 USB Connected Fig 10 3 5 Video Out TV out Cable Connection Insert the video out cable into the video out port of the tool and the other end of the cable into the video in port of a TV the LCD screen will output a high quality real time image 11 www obd2express co uk 4 Battery Charging Precautions To reduce th2. Date and Time s TV out Fig 18 Date and Time In the Advanced Settings screen select Date and Time and press OK button then the Date and Time setting screen will appear Fig 19 Date and Time 4 Month Day Year aJ 0 0 0 Time 24 ED Fig 19 Use the LEFT RIGHT button to move to the desired dialog box then use the UP DOWN button to increase or decrease the number When finished press OK button to save configuration and exit or press Back button to exit without saving changes 24 www obd2express co uk Language In the Advanced Settings screen select Language and press OK button then the Language setting screen will appear Fig 20 v English is the default language English Espaniol Francaise Deutsch Nederlands IP Fig 20 Use the UP DOWN button to move to the desired language then press OK button to save configuration and exit or press Back button to exit without saving changes TV out In the Advanced Settings screen select TV out and press OK button then the TV output setting screen will appear Fig 21 NTSC is the default standard Fig 21 Use the UP DOWN button to select the desired setting then press OK button to save configuration and exit or press Back button to 25 8 9 www obd2express co uk exit without saving changes Capturing a Photo When in the live screen make sure the camera icon is present at the top left portion of the sc
3. humidity 5 95 non condensing display unit Video output RCA TV out NTSC PAL 1 User s Manual 2 Imager Head and Cable 8 5mm is standard 5 5 mm is optional 3 Magnet Mirror and Hook hook will only be available when 2 3 Accessories Included 8 5mm imager head is provided 4 Charger 5 USB Cable 6 Video out Cable TV out Cable 7 Protective Carrying Case 4 www obd2express co uk 2 4 Tool Components and Ports The MaxiVideo MV400 comes with the following items Note Because of continuing improvements actual product may differ slightly from photo 1 2 3 4 5 Fig 1 Handheld Display Unit The ergonomic tool with comfortable pistol grip design Imager Head and Cable Connects to the tool while in use to view images and videos Cable Connector Connects the handheld display unit to the imager head and cable Charging Indicator Light Illuminates red when charging and illuminates green when charging completed Power Button Turns on off the tool 5 6 7 8 9 10 11 12 13 www obd2express co uk DC Power Source Port Connects the tool to the mains with the supplied charger to power on the tool or to charge battery Micro SD card Slot Holds the Micro SD card Video out Port Connects the tool to a TV with the supplied video out cable to view the real time image Mini USB Port Connects the tool to a computer with the s
4. ble into corrosive oily places and be sure to keep the imager head and cable away from high temperature objects Do not immerse the tool and display unit in water Such measures reduce the risk of electric shock and damage Do not use excessive force to insert or withdraw the imager head and cable This may result in damage to the tool or inspection area Do not use the imager head and cable to modify surroundings clear pathways or clogged areas Do not place the imager head and cable into anything or anywhere that may contain a live electric charge or moving parts which increases the risk of electric shock or entanglement injuries Do not use the tool for personal inspection or medical use in any way This is not a medical tool Do not eat or smoke while operating the tool Use hot soapy water to wash hands and other body parts exposed to drain contents after using the tool to inspect drains and other areas that may contain chemicals or bacteria which will help prevent contamination with toxic or infectious material When the inspection is completed carefully withdraw the imager head and cable from inspection area Store idle components out of the reach of children and other untrained persons Maintain the tool with care Properly maintained tools are less likely to cause injury Do not drop the tool if the tool is dropped accidently check for the breakage and any other conditions that may affect its operation 16 www obd2express
5. card has been 29 www obd2express co uk inserted into the tool 4 Esun Camera Indicates the tool is operating in still camera mode 5 EilVideo Camera Indicates the tool is operating in video camera mode 5 7 Software Update NOTE The tool supports software update when there is new progress with software or system We offer free update file for the tool 1 Format your Micro SD card to FAT file format on a computer 2 Visit our website www auteltech com and download software update file to your Micro SD card 3 Insert your Micro SD card into the Micro SD card slot See 3 3 Micro SD card Installation 4 Press Power button to turn on the tool and then press UP button until the update screen pop up select YES to upgrade the tool Fig 29 Updating Updating Fig 29 30 www obd2express co uk 6 Troubleshooting Possible Solutions dk Reason en 7 Check and connection is reattach Display is on but does not loose show image Imager head is Check if it is covered by covered by debris debris LED on imager head are dim period at max brightness display changes between monochrome color display turns itself OFF after a short Low battery Charge battery The tool will not turn on Dead battery Replace battery 31 www obd2express co uk 7 Warranty Information 7 1 Limited One Year Warranty Autel warrants to its customers that this pro
6. co uk Use only accessories that are recommended by the manufacturer for the tool Dry your hands when operating the tool or charging the battery Always use appropriate personal protective equipment while handling and using the tool Appropriate personal protective equipment always includes safety glasses and gloves and may include latex or rubber gloves face shields goggles protective clothing respirators and steel toed footwear Protect against excessive heat The tool should be kept away from heat sources such as radiators stoves or others that produce heat Do not use the tool near moving machinery or areas where the temperature will exceed 113 F 45 C Store the tool charger and all cables in a locked area out of the reach of children and people unfamiliar with tool 5 3 Tool Inspection Before using inspect your tool and correct any problems to reduce the risk of serious injury from electric shock and other causes and prevent tool damage Make sure the power is OFF Clean any oil grease or dirt from the tool especially on the buttons and ports This helps prevent the tool from slipping from your hands Inspect the imager head lens for condensation To avoid damaging the tool do not use the tool if condensation forms inside the imager head Let the water evaporate before using again Inspect the full length of the cable for cracks or damage A damaged cable could allow water to enter the tool and increase the
7. corrected The tool is not explosion proof and can cause sparks v Do not use the tool while standing in water Check the area and determine if MaxiVideo MV400 Digital Inspection Videoscope is the correct tool for the job v Check the access points to the area v Check if there is any electric power supplied to the area to be inspected v Check if the any liquids will be occurred during the 18 3 4 www obd2express co uk inspection The Imager head and cable were waterproof to a depth of 3m 10 Greater depths may cause leakage into the imager head and cable and cause electric shock or damage the tool The display unit is not waterproof and should not be exposed to wet conditions v Check if any chemicals are present especially in the case of drains Chemicals may damage the tool v Check the temperature of the area The working temperature of the tool is between 32 F 0 C and 113 F 45 C v Check if any moving parts are present in the area Make sure the tool has been properly inspected Install the correct accessories for use in the appropriate application CAUTION Make sure the tool has been powered off before performing maintenance Tool maintenance must be performed only by qualified repair personnel Maintenance performed by unqualified repair personnel could cause injury When maintaining use only identical replacement parts Use of unauthorized parts or failure to follow maintenance instructio
8. duct will be free from all defects in materials and workmanship for a period of one 1 year from the date of the original purchase subject to the following terms and conditions 1 The sole responsibility of Autel under the Warranty is limited to either the repair or at the option of Autel replacement of the tool at no charge with Proof of Purchase The sales receipt may be used for this purpose 2 This warranty does not apply to damages caused by improper use accident flood lightning or if the product was altered or repaired by anyone other than the Manufacturer s Service Center 3 Autel shall not be liable for any incidental or consequential damages arising from the use misuse or mounting of the tool 4 All information in this manual is based on the latest information available at the time of publication and no warranty can be made for its accuracy or completeness Autel reserves the right to make changes at any time without notice 7 2 Service Procedures If you have any questions please contact your local store distributor or visit our website at www auteltech com If it becomes necessary to return the tool for repair contact your local distributor for more information 32
9. e risk of serious injury read these precautions and the label on charger s surface carefully before using 4 1 Battery Charging Safety Do not probe charger with conductive objects Do not use charger if it has been dropped or damaged in any way Charge battery in temperatures above 41 F 5 C and below 113 F 45 C When in use the charger shall be kept out of heat high voltage and avoided children s touching Use the supplied charger Do not charge the battery over 24 hours Do not allow anything to cover the charger while in use Unplug the charger from outlet before attempting any maintenance or cleaning Do not store charger in damp wet or explosive environment Do not open charger housing Have repairs performed only at authorized locations Do not charge battery near fire or in the sunlight Proper care will prevent serious damage to the charger 4 2 Battery and Charger Specifications Input 100 240 VAC 12 VDC 50 60Hz Output 5V DC Battery Type 3 7V lithium ion Battery 1640 mAh Capacity Input Current 0 3A DC or USB Charging Time 5 6 hours Passive convention cooling No Cooling fan 12 www obd2express co uk 4 3 Charger Inspection Before using inspect the charger and correct any problems Set up charger according to these procedures to reduce the risk of injury from electric shock fire and other causes and prevent tool damage 1 Make sure cha
10. een two modes as you desired 3 Press UP and DOWN arrow buttons to zoom in or out while in the camera mode where you can see a zoom indicator bar as you adjust zoom 4 Press LEFT and RIGHT arrow buttons to decrease or increase screen backlighting while in the camera mode where you can see a brightness indicator bar as you adjust LED light intensity 5 Press Play button to view captured photos and videos 6 Press Trash Can Reverse button to delete captured photos and videos as you needed when play back captured photos and videos 7 Press Trash Can Reverse button to control the direction of the real time image and video as you needed in the live screen 8 Press Setting Back button to enter Setup mode or return to the previous screen 9 Use the supplied accessories to provide application flexibility 10 Use the supplied USB cable to connect the tool to a PC to upload and view captured photos and videos 11 Connect the supplied video out TV out cable to video out port of the tool and the other end of the cable to the video in port of a TV to view a high quality real time image 15 www obd2express co uk 5 2 Operation Precautions Use the tool only as directed Do not operate the tool unless the user s manual has been read thoroughly and proper training has been completed The display unit is not waterproof The imager head and cable are waterproof but not acid proof or fireproof Avoid submersing the imager head and ca
11. ennennssnnsnnsensenee 12 4 1 BATTERY CHARGING SAFETY sesse se ese ese ese ese ese ee see eke Gee se ese ee ee Gee ke Gee Se ee ee 12 4 2 BATTERY AND CHARGER SPECIFICATIONS esse se see see see se ese ee ee eke see see see se eie 12 4 3 CHARGER INSPECTION uie esse oge hot base Ges esge be Gee tease cieie ou ce EER GEK ees Ee eeue oy 13 4 4 BATTERY CHARGING PROCEDURES ees ese ee see see see eke see see ge ee ee eke eke Gee see se ee 13 5 OPERATION INSTRUCTIONS see esse sesse esse soe sees see Se Ge Bee Se Ee Ge Bee Se EE Ge Ge 15 5 BASIC OPERATION iese skend eek ae 15 5 2 OPERATION PREGAUTIONS issie kes es soge esse SEGE ER eek Re Kees ESE EEES He ke ee ge bee EE 16 5 3 TOOL INSPECTION re irese a EA EE EE N 17 5 4 TOOL AND WORK AREA SET UP ees esse se ese ee ee see see eke ee Gee ge ee ee ee eke Ge Ge ee 18 5 5 ON SCREEN NAVIGATION cccccsssceessseceesseeecessseccesseecesaeecesssecceeseeeessasecessaees 20 www obd2express co uk 5 6 ICONS esse sees 5 7 SOFTWARE UPDATE 6 TROUBLESHOOTING 7 WARRANTY INFORMATION sesse sesse se see esse se Se eg e ee Be Se Ee Ee Be ER ee Ee Be Se ee Ee ee 7 1 LIMITED ONE YEAR WARRANT Y ccccccsssccesssscceesscecessseecesssecceseeeessseeeessaees 7 2 SERVICE PROCEDURES www obd2express co uk 1 Safety Instructions To prevent personal injury or damage to vehicles and or the scan tool read this instruction manual first and observe the following saf
12. enu mode LEFT Arrow LED Lighting Adjusting Button Uses Left arrow button to decrease LED brightness in the camera mode Moves the cursor to the desired item Moves to the previous image or video in the play mode RIGHT Arrow LED Lighting Adjusting Button Uses Right arrow button to increase LED brightness in the camera mode Moves the cursor to the desired item Moves to the next image or video in the play mode OK Button Confirms a selection or action from a menu Starts recording image or video in live mode Starts or suspends file reviewing in play mode www obd2express co uk 3 Installation and Connection 3 1 The Imager Head and Cable Installation To use the tool the imager head and cable must be connected to the display unit To connect the cable to the display unit make sure the key and slot Fig 4 are properly aligned Once they are aligned finger tighten the knurled knob to hold the connection firmly in place Fig 5 3 2 Accessories Installation For MV400 with 8 5mm imager head The three accessories include magnet hook and mirror Fig 2 All are attached to the imager head in the same manner Hold the accessory and the imager head as shown in Fig 6 Slp the end of the accessory over the imager head and then fix the accessory as shown in Fig 7 www obd2express co uk Eales Fig 6 Fig 7 For MV400 with 5 5mm imager head The two accessories include magnet and mirror Fig 3
13. ety precautions at a minimum whenever working on a vehicle 1 1 Work Area Safety Always perform automotive testing in a safe environment Keep your work area clean and well lit Cluttered benches and dark areas may cause accidents Keep clothing hair hands tools test equipment etc away from all moving or hot engine parts Operate the tool in a well ventilated work area Do not operate the tool in explosive atmospheres such as in the presence of flammable liquids gases or heavy dust Keep a fire extinguisher suitable for gasoline chemical electrical fires nearby Do not use the tool around corrosive chemicals which can ruin the photo quality Keep bystanders children and visitors away while operating the tool Keep the tools dry clean free from oil water and grease Use a mild detergent on a clean cloth to clean the outside of the tool when necessary 1 2 Electrical Safety Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators Do not expose the tool to rain or wet conditions Water entering the tool will increase the risk of electric risk Do not abuse the cord Never use the cord for carrying pulling or unplugging the tool Keep cord away from heat oil sharp edges or moving parts If operating the tool in a damp location is unavoidable use a ground fault circuit interrupter GFCI to protect supply 1 www obd2express co uk 1 3 Per
14. hands connect the tool to a PC with USB cable 13 www obd2express co uk to start charging The battery will begin charging automatically While the battery is charging the charging indicator light will be red When the battery is fully charged the charging indicator light will be green Once the battery is charged it may remain until it is ready to be used There is no risk of over charging the battery When the battery has been fully charged the charger automatically switches to retention charging Unplug charger from outlet once charging completes NOTE New battery reaches full capacity after approximately 5 charging and discharging cycles 14 www obd2express co uk 5 Operation Instructions Always wear safety eye protection to protect your eyes against dirt and other objects Follow operation instructions to reduce the risk of injury from electric shock entanglement and other causes 5 1 Basic Operation NOTE When in operation the cable can be bent into a certain shape This may help you operate the cable into confined areas 1 Hold the tool with LCD screen facing you and press Power button to turn it on Wait for two seconds the first screen a splash screen is booting up and then appear a live screen where you can do most of your work 2 Press OK button to capture photos in the camera mode press OK button to begin capturing videos in the video mode Press Camera Video button to switch betw
15. iles based on different formats 27 www obd2express co uk Fig 25 While viewing these photos and videos press OK button to select and then the screen will display as below Fig 26 The digit on the top left portion of the screen shows sequence number of the playing file and total number of files in the folder Fig 26 Use the LEFT button to play the previous file the RIGHT button to the next file Or use the UP button to play the file on the previous line the DOWN button to the file on the next line While selecting a video to play press OK button to start suspend or resume the process Anytime pressing BACK button will stop playing and exit While reviewing a photo or video press Trash Can Reverse button to delete the recorded files and the screen will display as below Fig 27 28 www obd2express co uk Are you sure to delete the file Yes No vi a Fig 27 Select Yes to confirm your selection and press OK button to delete the file or select No to cancel the command and press OK button to exit NOTE Files or videos only can be deleted one by one v When you delete all the photos or videos a No Files Available message appears on the screen Fig 28 MV400 NO FILES AVAILABLE Fig 28 5 6 Icons pg BEd DC Power Indicates the tool is supplied by external power 2 Battery Capacity Fully charged battery 1 3 g Micro SD card Indicates a Micro SD
16. ns may create a risk of electric shock or injury Do not attempt to take any pieces of the tool apart unless directed by the manual Follow instructions to change accessories Do not use acetone to clean the tool Instead use only alcohol to swab the connections Avoid rubbing too hard on the LCD screen After using wipe the display unit clean gently with a dry cloth Upon the completion of any maintenance of the tool ask qualified repair personnel to perform safety checks to examine if the tool is in proper operating condition Stop using the tool if it starts smoking or emitting noxious fumes 19 www obd2express co uk Always handle the tool with care It is not shock resistant Do not disassemble the tool beyond what is shown in the manual Doing so will void your warranty 5 5 On Screen Navigation 1 2 3 4 Splash Screen When the tool is powered on the first screen displayed is referred to as the splash screen Fig 11 This screen tells you the tool is booting up Once the tool is fully powered up the screen will automatically switch to the live screen MaxiVideo MV400 www auteltech com Autel Fig 11 Live Screen The live screen is where you will do most of your work A live image of what the imager head sees is displayed on the screen You can zoom adjust screen backlighting rotate images and videos view and capture photos and videos from this screen Switching from S
17. reen Fig 22 Press OK button to capture a photo and simultaneously the photo has been saved to internal memory or the Micro SD card if available 457 2012 04 26 17 17 54 Fig 22 NOTE Figure at the top left under the camera icon indicates how many photos you can save in the space left Capturing a Video While in the live screen make sure the video icon is present at the top left portion of the screen Fig 23 Press OK button to start capturing video You will notice that a red REC icon appears at the top right portion of the screen just below battery capacity icon This shows that video is capturing The time at the top left portion just below video icon will begin counting This indicates how long the video has been captured Press OK button again to stop capturing a video 26 10 www obd2express co uk 3 00 35 20 2012 04 26 17 17 54 Fig 23 It may take few seconds to save the captured video to internal memory The tool could capture a video approximately 80s without a Micro SD card NOTE Before capturing a video figure at the top left under the video icon indicates how long a section of video you can save in the space left Fig 24 ib 00 05 20 2012 04 26 17 17 54 Fig 24 Playing Back and Deleting Captured Photos and Videos Pressing Play button the captured photo and video files will display on the screen Fig 25 Photos and videos captured will be saved at separate f
18. rger is unplugged Inspect the power cord and charger for damage or modifications or broken worn missing misaligned or binding parts If any problems are found do not use the charger until the parts have been repaired or replaced Clean any oil grease or dirt from the tool especially on the buttons This helps prevent the tool from slipping from your hands and allows proper ventilation Inspect if the warning label on charger s surface is intact and readable Select appropriate location for charger before using Check work area for The charger must be between 41 F 5 C and 113 F 45 C for charging If the temperature of either is outside of this range at any point during charging the operation will be suspended until brought back to the correct temperature range Inspect that the plug fits correctly into the desired outlet The charger needs a clearance of at least 4 10 cm on all sides to maintain a proper operating temperature 4 4 Battery Charging Procedures The tool has a 3 7V built in lithium ion rechargeable battery When the battery is too low the Battery Capacity Icon will blink 25 times and the tool will shut down automatically There are two means of charging battery 1 2 To charge battery by charger Locate the DC power source port of the tool With dry hands connect the tool to the mains with charger to start charging To charge battery by USB cable Locate the USB port of the tool With dry
19. risk of electric shock Make sure the connections between the display unit and imager head and cable are tight All connections must be properly assembled for the cable to be waterproof Check if the warning label is present firmly attached and readable Do not operate the tool without the caution label 17 www obd2express co uk Turn on the power and make sure the tool model through the splash screen and then display the live screen If the tool does not work well after being turned on please have the tool checked by a qualified technician Any tool that cannot be controlled with the power button is dangerous and must be repaired NOTE Please check following methods to avoid injury v v FOR WALLS For inspecting the inside walls be sure to shut off the circuit breaker to the whole house before using the tool FOR PIPES If you suspect a metal pipe could contain an electric charge have a qualified electrician to check the pipe before using FOR AUTOMOBILES Be sure the automobile is not running during inspection Metal and liquid under the hood may be hot Don t get oil or gas on the imager head 5 4 Tool and Work Area Set Up Set up the tool and work area according to these procedures to reduce the risk of injury from electric shock entanglement and other causes and prevent tool damage 1 2 Check work area for v Sufficient lighting v Do not work in area until flammable sources have been identified and
20. sonal Safety Do not use the tool while tired or under the influence of drugs alcohol or medications A moment of interruption can result in serious personal injury Do not over reach Keep proper footing and balance at all times Proper footing and balance enables better control of the tool in unexpected situations Always wear safety eye protection that meets ANSI standards Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Do not place the tool on any unstable cart or surface The tool may fall causing serious injury to a person or serious damage to the tool itself Never spill liquid on the display units Liquid increases the risk of electric shock and damage to the tool Do not use the tool for personal or medical use in any way The product is not shock resistant Do not use it as a hammer or drop it www obd2express co uk 2 Description Specifications and Tool Components 2 1 Description This premier Autel MaxiVideo MV400 digital videoscope is an ideal tool for inspecting difficult to reach areas normally hidden from sight It features the ability to record digital still images and MPEG 2 or MPEGI1 videos either on its internal memory or on the removable Micro SD card Optional The ergonomic tool not only features a 3 5 full color LCD screen auto focus and viewing capacity as close as 1 with crys
21. tal clear output but also offers the capacity to stream digital video directly to a PC The multipurpose videoscope is an economical solution to inspect machinery facilities and infrastructure in the safest quickest and most cost effective manner possible 2 2 Specifications Recommended use Indoor 1 to 14 2 5cm to 35 6cm with 8 5mm Optimal viewing diameter imager head Distance 3 8 to 12 0 95cm to 30cm with 5 5mm diameter imager head JPG images 640x480 Image capture AVI videos 320 x 240 Screen type display 3 5 TFT LCD Display resolution 320 x 240 Built in rechargeable lithium ion battery Fower supply pack 3 7V 1640 mAh Tested battery life 3 4 hours of continuous use i 199 x 100 x 178mm 7 83 x 3 94 x Dimensions 7 0 www obd2express co uk Weight 0 288kg 0 631bs Recording medium Micro SD card Micro SD card is optional and not included Image controls Zoom low light vision Lighting Fully adjustable LED Cable reach Im 3 expandable to 6m 19 w optional extensions Imager head 18 5mm 0 33 is standard and 5 5mm 0 22 is optional Waterproof Imager head and cable to 3m 10 Additional ports USB video out TV out port Operating temp Main unit 32 F to 113 F 0 C to 45 C Cable 14 F to 176 F 10 C to 80 C Storage temp 4 F to 158 F 20 C to 70 C Operating
22. till Image Capture to Video Capture By default the tool will turn to still image capture when powered on Press Video Camera button to switch between still image capture and video capture as you needed Adjusting screen backlighting Pressing RIGHT and LEFT arrow buttons on the key pad in the still camera mode will increase or decrease the screen backlighting 20 5 6 www obd2express co uk A brightness indicator bar will be displayed on the screen as you adjust brightness Fig 12 X HE a m 0 100 2012 04 26 17 17 54 Fig 12 Zooming Simply press UP and DOWN arrow buttons while in the still camera mode to zoom in or out A zoom indicator bar will be displayed on the screen as you adjust zoom Fig 13 2012 04 26 17 17 54 Fig 13 Entering the Primary Settings Screen Pressing Setting button while in the live screen will take you to the primary settings screen Fig 14 Pressing Back button at any point will take you back to the live screen 21 www obd2express co uk Advanced Settings Color or Black White Format Media Help Ooces Fig 14 Color or Monochrome In the Setup screen select Color or Monochrome and press OK button then the Color or Monochrome setting screen will appear Fig 15 v Color is the default mode Color or Monochrome Color Monochrome Q Fig 15 Use the LEFT RIGHT button to move to the desired option then press OK button to save configura
23. tion and exit or press Back button to exit without saving changes Format Media In the Setup screen select Format Media and press OK button then the Format Media setting screen will appear Fig 16 22 www obd2express co uk Format Media Fig 16 If you want to format the media in most cases it is the Micro SD card use the LEFT RIGHT button to select Yes then press OK button to begin formatting When formatting is finished it will take you back to the primary settings screen If you do not wish to format media use the LEFT RIGHT button to select No then press OK button to return to previous menu or press Back button to exit NOTE Before performing the formatting make sure you have reviewed the recorded files thoroughly Help This function provides the firmware version information In the Setup screen select Help and press OK button then the firmware version screen will appear Fig 17 MV400 Firmware Version V1 0 8 Fig 17 23 7 www obd2express co uk Entering the Secondary Settings Screen While in the Primary Settings Screen Fig 14 select Advanced Settings from Setup and then press OK button you will enter the secondary settings screen Fig 18 where you can set Date and Time Language and TV out as needed Pressing Back button at any point will bring you back to the primary settings screen and pressing it again will bring back to the live screen Advanced Settings
24. upplied USB cable to exchange information Battery Compartment Cap Indicates to install or remove the battery Accessory Magnet Picks up small metal objects such as dropped rings or screws on the floor Accessory Hook Unclogs obstacles and picks up wires in the pipes or confined areas Accessory Mirror Helps users look around corners and see the unreachable areas INI 9 BE Fig 2 8 5mm accessories Er Fig 3 5 5mm accessories www obd2express co uk 2 5 Buttons and Controls Fig 4 A LCD Screen Indicates still images and videos B Trash Can Reverse Button Deletes captured photos and videos in the play mode While capturing a photo or video press Reverse Button will control the direction of the real time image and video in the live screen The real time image and video will do a horizontal reverse or a vertical reverse C Play Button Replays captured photos and videos D Setting Back Button Moves to the primary settings screen while pressing again will return to the last viewed screen E Camera Video Button Switches between two modes camera or video F UP Arrow Zoom Adjusting Button Uses Up arrow button to zoom in while in the camera mode Moves up through menu and submenu items in menu mode G DOWN Arrow Zoom Adjusting Button Uses Down arrow button to zoom out while in the camera mode Moves down 7 www obd2express co uk through menu and submenu items in m
25. www obd2express co uk Table of Contents 1 SAFETY INSTRUCTIONS wessssssscssscsssssscsssossssssssssssecsscasccsscasvesssossesssescasssssscnsonsteers 1 11 WORK AREA SAFETY iese ees bes sesse nee Need oe Ee Geek deeg edge bene Pe GEE EEE OiR EEst 1 1 2 ELECTRICAL SAFETY ciiir EL EES GES BONE Ee sp berbere GEE GEE ENG SG Ge EER ER 1 1 3 PERSONAL SAFETY cinici versie eed enge n be Ee aR eE Pi a bee Eyes oge deed 2 2 DESCRIPTION SPECIFICATIONS AND TOOL COMPONENTS 000 3 2 1 DESCRIPTION EE RE EE EE N 3 2 2 SPECIFICATIONS sei mu ER N EE 3 2 3 ACCESSORIES INCLUDED iss eeste soas ese Ens eE E E EEE a 4 2 4 TOOL COMPONENTS AND PORTS e sesse sesse se ee see ee ee Ge Ge Ge ee ee Re Ge GR Ge 5 2 5 BUTTONS AND CONTROLS uses ordes sees ese sed gese sp eiiiai eii sigiri ee Ke Se gek ee 7 3 INSTALLATION AND CONNECTION i esessesvesvvssneensensennvenneensensennnsnnnensensenseennee 9 3 1 THE IMAGER HEAD AND CABLE INSTALLATION ees see see sesse ee see ee ee see ee ee ee 9 3 2 ACCESSORIES INSTALLATION ees see see see se ese ee ese ee see eke Ge Se be ee ee Re Re Ge SR ee 9 3 3 MICRO SD CARD INSTALLATION iese sesse ese se ee ee ee ee ke Ge ee ee Re Re Ge Ge ee 10 3 4 USB CABLE CONNECTION i e sees bee ses ee bee e Ge Ee ba ego gee sd eu Eb be eN eo be bee bee ee 11 3 5 VIDEO OUT TV OUT CABLE CONNECTION cccscccssseessessseeseeesseeeeeesaes 11 4 BATTERY CHARGING PRECAUTIONS sessvosneevsesvesnvsnnennesneense
Download Pdf Manuals
Related Search