Home

User`s Manual - Operating Guide

1. Rear Power ON OFF NOTE e Turn the power on off in right order Please power on the projector before the connected devices Power off the projector after the connected devices Turning On The Power 4 Remove the lens cap STANDBY ON 9 Set the power switch to ON The STANDBY ON indicator will light to solid orange Co STANDBY ON button 3 Press the STANDBY ON button Ff The projector lamp will light up and the STANDBY ON indicator will begin blinking green Power switch ON position When the power is completely on the indicator will stop blinking and light green LENS SHIFT 4 Use the LENS SHIFT buttons to shift the picture upward or downward LENS SHIFT buttons 5 Select an input signal according to the section Selecting An Input Signal of the following page Turning Off The Power 4 Press the STANDBY ON button The message Power off will appear on the screen for approximately 5 seconds STANDBY ON Press the STANDBY ON button again while 2 Power off the message is visible The projector lamp will go off and the STANDBY ON indicator will begin blanking orange Then the STANDBY ON indicator will stop blinking and light to solid orange when the lamp cooling is complete Power switch OFF position CD STANDBY ON button Switch the power switch to O OFF The STANDBY ON indicator will go off Attached the lens cap 19 16 Upe
2. This table is continued to the following page 43 a4 Troubleshooting continued Regarding The Indicator Lamps continued STANDBY ON LAMP TEMP nesctintion indicator indicator indicator p Lighting in Red Lighting in Red Lighting in Red Lighting in Green Lighting in Green Blinking Turned in Red off Blinking in Red Turned Lighting off in Red Alternative Blinking in Red Simultaneous Blinking in Red Either there is no lamp and or lamp cover or either of these has not been properly fixed Please turn the power off and allow the unit to cool down at least 45 minutes After the projector has sufficiently cooled down please make confirmation of the attachment state of the lamp and lamp cover and then turn the power on again If the same indication is displayed after the treatment please contact your dealer or service company The cooling fan is not operating Please turn the power off and allow the unit to cool down at least 20 minutes After the projector has sufficiently cooled down please make confirmation that no foreign matter has become caught in the fan etc and then turn the power on again If the same indication is displayed after the treatment please contact your dealer or service company There is a possibility that the interior portion has become heated Please turn the power off and allow the unit to cool down at least 20 minutes After the projector has sufficiently
3. amp REC709 REC601 Selecting the AUTO automatically selects the optimum mode COLOR space memo This item can be selected only at a RGB signal or a component video signal other than a COMPONENT port input of 525i 480i 625i 576i SCART RGB memo The AUTO operation may not work well at some signals In such a case select a suitable mode except the AUTO Select a function of COMPONENT port using the 4 Y buttons COMPONENT SCART RGB COMPONENT When the SCART RGB is selected the COMPONENT port function as a port for a SCART RGB signal input Please refer to the section Connecting Your Devices Select a signal type mode using the 4 Y buttons AUTO NTSC amp PAL SECAM NTSC4 43 amp M PAL amp N PAL selecting the AUTO automatically selects the optimum mode memo This item is performs only at a video signal from the VIDEO port or the S VIDEO VIDEO port For a component video signal the signal type is identified automatically independently of this function memo The AUTO operation may not work well at some signals If the picture becomes unstable ex a irregular picture a color lack please select the mode depending on the input signal Select the TURN ON or the TURN OFF using the A Y buttons TURN ON amp TURN OFF When the TURN ON is selected the 3D YCS mode works for a completely still 3D YCS image or images with few motions memo This item performs only at a video signal of NTSC3 58 memo Whe
4. ON indicator TEMP indicator LAMP indicator LENS SHIFT buttons INPUT dial SEARCH button M1 D indicator RGB indicator BNC indicator COMPONENT indicator S VIDEO indicator VIDEO indicator ZOOM buttons FOCUS buttons KEYSTONE button MENU button RESET button ENTER button Cursor buttons amp W lt p gt LASER INDICATOR VIDEO button RGB button BLANK button ASPECT button LASER button Cursor buttons amp W lt p gt 4D Mouse move pointer ESC button Keyboard key 4D Mouse right button POSITION button AUTO button PinP button MAGNIFY buttons FREEZE button VOLUME button MUTE button ID CHANGE switch Refer to the illustrations and tables below to determine the screen size and projection distance The values shown in the table are calculated for a full size screen 10 Reference for ae the 4 3 aspect ratio inch cm Reference for i i the 16 9 aspect ratio Setting Up continued Adjusting The Projector s Elevator You can use the elevator feet to make adjustments if the surface on which you need to set the projector is uneven or if you otherwise need to adjust the angle of projection The adjustment range of the elevator feet is O to 9 degrees 4 Press and hold in the elevator buttons Elevator buttons Raise or lower the projector to the desired height and 2 then release the elevator buttons When you release the elevator buttons the
5. an unsuitable signal reaches at the set time Please refer to the section Turning Off The Power This table is continued to the following page 29 30 Multifunctional Settings continued AUTO Menu continued a ae Select the TURN ON or the TURN OFF using the A Y buttons TURN ON amp TURN OFF When the TURN ON is selected detecting no signal cycles through input ports and displays the picture of retrieved signal M1 D gt RGB BNC SEARCH VIDEO S VIDEO COMPONENT memo When the TURN ON is selected pressing the RGB button selects the M1 D ports and pressing the VIDEO button selects the COMPONENT port memo If no signal is found or the projector is unstable to find an input signal at any of its ports it will return to the state it was in prior to the search Select the EXECUTE using the button to reset the AUTO menu items EXECUTE CANCEL The items of the AUTO menu are collectively returned to the initial setting Note that the item ADJUST is not reset Multifunctional Settings continued With the SCREEN performed Perform each operation in accordance with the instructions in the table below MENU BLACK ORIGINAL MAIN BLANK PICTURE 2 MyScreen INPUT AUTO OPTION NETWORK MyScreen LOCK TURN OFF MENU POSITION MESSAGE RESET menu the items shown in the table below can be TURN ON re START UP MyScreen LOCK MENU POSITION Select a type
6. and change the lamp by THE POWER WILL TURN OFF referring to the section Lamp After changing the lamp please AFTER 0 hr be sure to reset the lamp timer This table is continued to the following page NOTE o A lamp has a finite product life Lamps are characterized by the fact that after long hours of usage a lamp will no longer light up or the lamp will break or burst etc This projector is equipped with an automatic shut down function such that the power will automatically be turned off when lamp usage time has reached 2000 hours Please be aware however that among lamp types there are major differences in product lifetimes a lamp may thus fail to light even prior to the functioning of the automatic shut down function of this projector 41 42 Troubleshooting continued Related Messages continued REMINDER HRS PASSED AFTER THE LAST The time the filter timer has counted has reached the FILTER CHECK interval time set by the FILER MESSAGE of FILTER MAINTENANCE IS SERVICE item in the OPTION menu ESSENTIAL TO REMOVE WARNING Please clear or change the air filter by referring to the section MESSAGE RESET FILTER TIMER Air Filter After caring for the air filter please be sure to reset i the filter timer SEE MANUAL FURTHER INFO The internal portion temperature is rising PLEASE CHECK THAT THE Please turn the power OFF and allow the unit to cool down at FILTER HAS BEEN CLEANED least 20 minute
7. elevator feet will lock into position Pro As necessary you can also finely adjust the height of 3 the projector by twisting the elevator feet by hand Using The Lens Shift Buttons The lens of this projector can be shifted vertically When you want to finely adjust the picture position use the LENS SHIFT buttons of the projector Elevator feet LENS SHIFT LENS SHIFT buttons Projector Remote control Setting Up continued Connecting Your Devices WARNING e Whenever attempting to connect other devices to the projector read thoroughly the User s Manual Safety Guide this manual and the manual of each device to be connected Incorrect connecting could result in fire or electrical shock CAUTION e TURN OFF ALL DEVICES prior to connecting them to the projector Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and or damage to the device and or projector ATTENTION e Make sure that you connect devices to the correct port Incorrect connection may result in malfunction and or damage to the device and or projector Refer to the section Technical of this manual for the pin assignment of connectors and RS 232C communication data e Some cables have to be used with core set Use the accessory cable or a designated type cable for the connection F
8. for closer viewing Keystone Distortion Correction Quick correction of distorted images electrically Optical Lens Shift The lens of this projector can be shifted vertically When you want to finely adjust the picture position use the LENS SHIFT buttons Preparation Please see the Contents Of Package of the User s Manual Quick Guide Your projector should come with the items shown there Contact immediately your dealer if anything is missing NOTE e Keep the original packing materials for future reshioment For moving the projector be sure to use the original packing materials Use special caution for the lens part Lontent Projector Features Tre cere Tee E Te 2 Preparation E E ee TE eT 2 Part Names errr Ee eT ree E ee ee ES 4 Projector Sen Gini Buarib cay aria A rE she Gas Geanerm Gers acetone 4 Control Buttons Sa a aa aS E E Ea ra ere ter esate E 5 Remote control E E 5 Setting Up EE E E a E E 6 Arrangement Desana EREEREER aa 6 Adjusting The Projectors Elevator Tere eee ee eee ee ee ee ee 7 Using The Lens shift Buttons 7 Connecting Your Devices 8 Connecting The Power Supply 11 Remote Control a ee 12 About The Laser Pointer 12 Loading Batteries occcccctrr ee 12 Operating The Remote Control ESPE EEES KEREI ETE ERS 13 Using The Remote ID Feature ET 13 Using The Mouse Keyboard Control Function GR WS hw Bw cw we aS re ee ee 14 Power ON OFF E E E eee wsesee es 15 Turning On The Po
9. registered in MyScreen will be of lesser quality than the original Select the TURN ON or the TURN OFF using the A Y buttons TURN ON amp TURN OFF The TURN ON disables the operation of the item MyScreen of this SCREEN menu Adjust the menu position using the amp W 4 P buttons Up tT e Right g Down memo To finish this operation press the ESC button but not the button Left This table is continued to the following page 31 Multifunctional Settings continued SCREEN Menu continued a re Select the TURN ON or the TURN OFF using the A Y buttons TURN ON amp TURN OFF When the TURN ON is selected the following message function works The message of the AUTO IN PROGRESS for the auto adjustment The message of the NO INPUT IS DETECTED The message of the SYNC IS OUT OF RANGE The message of the Searching The message of the Detecting The indication of the input signal by input change The indication of the aspect ratio by changing the aspect ratio The indication of FOCUS by adjusting the focus The indication of FREEZE and Il while freezing the screen by pressing the FREEZE button memo When the TURN OFF is selected please remember if the picture is freezing Do not mistake freezing for a malfunction Select the EXECUTE using the button to reset the SCREEN menu items EXECUTE CANCEL The items of the SCREEN menu are collectively ret
10. sounds nor pictures are outputted The electrical power cord is not plugged in Correctly connect the power cord The power switch is not set to the on position E i 15 Set the power switch to On 15 minutes After the projector has sufficiently cooled down please turn The main power source has been interrupted during operation such as by a power outage blackout etc Please turn the power off and allow the unit to cool down at least 20 the power on again Either there is no lamp and or lamp cover or either of these has not been properly fixed Please turn the power off and allow the unit to cool down at least 45 37 38 minutes After the projector has sufficiently cooled down please make confirmation of the attachment state of the lamp and lamp cover and then turn the power on again The signal cables are not correctly connected Correctly connect the connection cables Signal source does not correctly work Correctly set up the signal source device by referring to the manual of the source device 1 The input changeover settings are mismatched l 16 Select the input signal and correct the settings This table is continued to the following page 45 46 Troubleshooting continued Phenomena That May Easily Be Mistaken For Machine Defects continued Phenomenon Cases not involving a machine defect Pictures are displayed but no sounds are heard Sounds are heard but no pict
11. table Related message A MESSAGE __ When TURN OFF is chosen the air filter cleaning message will not appear Selecting TUR OFF displays the message to call an attention to disabling the air filter cleaning message e Please check and clean the air filter periodically even if there is no message If the air filter becomes blocked by dust or others the internal temperature will rise which could cause malfunction or reduce the lifetime of the projector e t is recommended to choose 100h in general Please be careful with the operating environment of the projector and the condition of air filter especially when 200h 300h or TURN OFF is chosen Select the EXECUTE using the button to reset the OPTION menu items EXECUTE amp CANCEL The items of the OPTION menu are collectively returned to the initial setting Note that the items VOLUME LAMP TIME FILTER TIME and SERVICE are not reset Multifunctional Settings continued MAIN SETUP PICTURE 1 DHCP TURN OFF PICTURE 2 INFORMATION This projector provides the NETWORK function If you use this uO function please set up the projector according to the Network paula environment in which you use it NETWORK GSeecT memo f DHCP function on your Network is activated the following operation is not normally required because DHCP function on this projector is active as initial settings Please see the section Network Setting
12. to use this function please consult your dealer for further information To start connect the NETWORK port to a gateway device via a CAT 5 cable then set up the projector according to the Network environment in which you use it When your Network enables the DHCP function You can set automatically if you set the DHCP function to TURN ON using the NETWORK menu Please refer to the section NETWORK Menu When your Network doesn t support the DHCP function or When you use a fixed address even if your Network can support the DHCP function Please set the IP Address the Subnet Mask the Default Gateway and the DHCP using the NETWORK menu RA At first set the DHCP function to TURN OFF You can set them using a Web Browser Internet Explorer 4 0 or higher on the computer connected to the Network Input the same IP address as set to the projector onto the Web Browser on the computer connected to LAN ex Case of IP Address 192 168 1 11 1 Input htto 192 168 1 11 2 Click ENTER 3 Input the required data according to the screen Ce eT a ses 4 O28 3 Ger GIBEA Ome SH a j PECA fE vrr ALIBIN ote sn 4 Make sure of the input data then click Write IP CONFIGURATION memo These setting will be active after reboot These eee a pez i fazan Psszsszss0 fazas F setting will be stored and used when DHCP is OFF wj settings 5 Click Return to top page return
13. B a memo The R G and B can be selected only when the USER Is selected under the COLOR TEMP Adjust the gamma data using the 4 Y buttons Up amp Down Select a color temperature using the 4 Y buttons Adjust the red color level for the USER mode of the COLOR TEMP using the 4 Y buttons Strong Weak Adjust the green color level for the USER mode of the COLOR TEMP using the 4 Y buttons Strong Weak Adjust the blue color level for the USER mode of the COLOR TEMP using the Y buttons Strong Weak COLOR BAL R Adjust the red color balance using the 4 Y buttons Strong Weak COLOR BALG Adjust the green color balance using the 4 Y buttons Strong Weak COLOR BAL B Adjust the blue color balance using the Y buttons Strong Weak Adjust the sharpness using the 4 Y buttons Clear amp Soft Adjust the whole color using the 4 Y buttons COLOR Strong lt Weak memo This item can be selected only at a video signal Adjust the tint using the A Y buttons TINT Green Red memo This item can be selected only at a video signal This table is continued to the following page Multifunctional Settings continued PICTURE 1 Menu continued e Select a command to load or save using the Y buttons and then press the P or the ENTER button to perform the function LOAD1 amp LOAD2 LOAD3 LOAD4 SAVE1 SAVE2 SAVE3 SAVE4 MY MEMORY This projector ha
14. Projector User s Manual Operating Guide Thank you for purchasing this projector NOTE The information in this manual is subject to change without notice e The manufacturer assumes no responsibility for any errors that may appear in this manual e The reproduction transfer or copy of all or any part of this document is not permitted without express written consent TRADEMARK ACKNOWLEDGMENT e VGA and XGA are registered trademarks of International Business Machines Corporation e Apple and Mac are registered trademarks of Apple Computer Inc e VESA and SVGA are trademarks of Video Electronics Standard Association e Windows is a registered trademark of Microsoft Corporation e Internet Explorer is a trademark of Microsoft Corporation All other trademarks are the property of their respective owners This multimedia projector is used to project various computer signals as well as NTSC PAL SECAM video signals onto a screen Little space Is required for installation and large images can easily be realized Ultra High Brightness Crisp ultra bright presentations is achieved by using a UHB ultra high brightness lamp and a highly efficient optical system Whisper Mode Equipped Special mode is available for reducing projector noise to achieve quieter operation User Memory Function This projector can memorize 4 settings by MY MEMORY function Partial Magnification Function Interesting parts of images can be magnified
15. TION menu shows the information about the current signal input as illustrated below P IN P INPUT lt 4 INPUT INFORMATION lt 4 INPUT INFORMATION lt 4 INPUT INFORMATION RGB S VIDEO COMPONENT INFORMATION 1024x768 60 0 SECAM 576i 50 FRAME LOCK AUTO SCART RGB memo The FRAME LOCK message means the frame lock function is working This function automatically works when a RGB signal with vertical frequency of 50 to 60 is input and it displays a moving picture more smoothly memo The SCART RGB message means the COMPONENT port is working as a SCART RGB port Please refer to the item COMPONENT in this table Select the EXECUTE using the button to reset the INPUT menu items RESET EXECUTE CANCEL The items of the INPUT menu are collectively returned to the initial setting Note that the item INFORMATION is not reset Multifunctional Settings continued AUTO Menu MAIN ADJUST P 5 P 3 INPUT ICTURE 1 POWER OFF 0 min ICTURE 2 SEARCH TURN ON With the AUTO menu the items shown in the table below can be ii performed Perform each operation in accordance with the AN instructions in the table below Sane 2 a Pressing the or the ENTER button performs the automatic adjustment E For an RGB signal The vertical position V POSITION the horizontal position H POSITION the clock phase H PHASE and the horizontal size H SIZE will be automatically adjusted And the aspect ratio ASPECT will be
16. URN ON amp TURN OFF When the TURN ON is selected the built in speaker works Select a remote sensor using the Y button 1 then switch it using the ENTER button 2 IR REMOTE 1 1 FRONT amp 2 TOP 3 REAR 2 0 Off M On memo A sensor cannot be turned off when the other two are off Always at least one sensor is on Select a number as an ID number for remote control using the 4 Y buttons ALL 18203 The projector is controlled by the remote control whose ID CHANGE switch is IR REMOTE ID set into the position of the same number as this number When the ALL is selected the projector is controlled by a remote control irrespective of the position of the ID CHANGE switch memo Please refer to the section Using The Remote ID Feature Pressing the button or RESET button displays the LAMP TIME menu Select the RESET using amp button to reset the timer RESET amp CANCEL LAMP TIME selecting the RESET resets the count of the lamp timer to O memo Perform this function only when you have replaced the lamp The lamp timer counts the used time of the current lamp to display the messages about the lamp Incorrect performing causes Incorrect operation of the messages memo About replacing the lamp please refer to the section Lamp Pressing the button or RESET button displays the FILTER TIME menu Select the RESET using amp button to reset the timer RESET amp CANCEL Selecting the RESET
17. Up a Press the or the ENTER button then the IP ADDRESS menu as right comes up ts rare a memo This menu will be shown only when the DHCP is disabled at the NETWORK menu The IP Address is identification number of the projector on the Network 1 Set the IP Address using the Y buttons memo The same IP Address with other units cannot be used Press the or the ENTER button at the IP ADDRESS menu then the SUBNET MASK menu SUBNET MASK comes up The SUBNET MASK is an address of the Rag E Network 2 Set the address of the Network to be used Press the or the ENTER button at the SUBNET DEFAULT GATEWAY MASK menu then the DEFAULT GATEWAY menu A PE OE i i comes up The DEFAULT GATEWAY is the main Eun device to access outside of the Network 3 Set the address of the device as gateway to an outer Network Select the TURN ON or the TURN OFF using the amp V buttons pastor Hi TURN ON TURN OFF If your Network doesn t support the DHCP function select the TURN OFF Pressing the or the ENTER button displays the INFORMATION menu MPORMATNON The menu shows the information about the current Network setting as illustrated right Select the EXECUTE using the 4 button to reset the NETWORK menu items RESET EXECUTE S CANCEL All items on the NETWORK menu are returned to the initial setting 35 36 m Network setting Up This projector provides the NETWORK function When you start
18. When this adjustment is excessive certain degradation may appear on the picture Also please note that it may not function correctly with some input Operating continued Adjusting The Volume 1 Press the VOLUME button As illustrated on the right a dialog will appear on the screen to aid you in adjusting the volume Use the cursor buttons 4 VY to adjust the volume Press the VOLUME button again to close the dialog and complete this operation memo Even if you don t do anything the dialog will automatically disappear after a few seconds Muting The Sound 1 Press the MUTE button As illustrated on the right a dialog will appear on the screen indicating that you have muted the sound Press the MUTE or VOLUME button to restore the sound memo Even if you don t do anything the dialog will automatically disappear after a few seconds Temporarily Blanking The Screen Press the BLANK button The input signal screen will shut off and a BLANK screen will appear memo You can set the BLANK screen using the menu Please refer to the item BLANK of the table of the section SCREEN Menu Press the BLANK button again to remove the blank screen and return to the input signal screen Cursor buttons VOLUME button MUTE button BLANK button 19 Operating continued Freezing The Screen 4 Press the FREEZE button As illustrated on the right a dialog will appear on the sc
19. a VCR DVD Player Projector R AUDIO IN L VIDEO Audio out R R AUDIO IN Audio out L AUDIO IN L Video out VIDEO IN E if using a s video signal S video out S video cable S VIDEO R AUDIO IN L VIDEO R AUDIO IN AUDIO IN L Audio out R Audio out L E if using a component signal COMPONENT Cr Pr out Cr Pr Ce Pe out Y out Audio out R Audio out L E if using a SCART RGB input COMPONENT R AUDIO IN L VIDEO CONTROL ETWORK i R CrlPa e B Ce Pe 2 SCART ac pee RAUDIO IN m SCART AUDIO IN L danie VIDEO IN Setting Up continued Connecting to a monitor Monitor Projector O0000 O0000 O0000 RGB in RGB cable _ RGB OUT Connecting to a speaker with amplifier S _ O CONTROL NETWORK OTE CONTROL JOO Speaker Projector iin os os a M QOOOO oO R AUDIO IN L VIDEO S VIDEO Audio in Stereo Mini cable AUDIO OUT Connecting The Power Supply 4 Connect the connector of the power cord to the AC inlet of the projector 9 Firmly plug the power cord s plug into the outlet Connector 11 Remote Control About The Laser Pointer A WARNING The laser pointer of the remote control is used in place of a finger or rod Never look directly into the laser beam outlet or point the laser beam at other people The laser beam can cause vision problems A CAUTION Use of contro
20. as input image signal cable to the unit environment around the unit etc the automatic adjustment may not work correctly In such a case please choose DISABLE to disable the automatic adjustment and adjust manually Select the lens type currently used using the Y buttons AUTO 1082030405 Please select depending on the following AUTO automatically selects optimum mode 1 for a standard lens Type NL 500 etc SERVICE LENS TYPE 2 for a fixed short throw lens Type FL 501 etc 3 for a short throw lens Type SL 502 etc 4 for a long throw lens Type LL 503 etc 5 for a super long throw lens Type LL 504 etc memo This setting has an influence on the keystone distortion etc memo About the optional lens ask your dealer Select the TURN ON or the TURN OFF using the A Y buttons LENS LOCK TURN ON amp TURN OFF Selecting the TURN ON locks the adjustment of the lens shift the zoom and the focus GHOST 1 Choose a color element of ghost using the bottons lt gt 2 Adjust the chosen element using buttons 44 V to disappear ghost Use the W button to set the timer for the interval to show the message for cleaning up the air filter on 100h 200h 300h amp TURD URE LENS TYPE AUTO After selecting 50h 100h 200h or 300h the message REMINDER will appear after the timer reaches the interval time set by this operation Please FILTER refer to the FILTER TIME item e f and the
21. automatically selected Make sure that the application window is set to its maximum size prior to attempting to use this feature Dark pictures may still be incorrectly adjusted Use a bright screen when adjusting E For a video signal or s video signal The signal type mode best suited for the respective input signal will be selected automatically This function is available only when the AUTO is selected to the item VIDEO ADJUST fi of the INPUT menu For a component video signal the signal type is identified automatically independently of this function E For a video signal s video signal or component video signal The vertical position and horizontal position will be automatically adjusted E For a component video signal The aspect ratio will be automatically selected The clock phase will be automatically adjusted memo This operation requires approximately 10 seconds and the message AUTO IN PROGRESS is displayed during the operation memo This operation may not work well at some signals If the picture becomes unstable ex a irregular picture a color lack please select the suitable mode to the item VIDEO of the INPUT menu Set the time using the A Y buttons Long max 99 minutes Short min O minute DISABLE POWER OFF ae When the time is set to 1 to 99 the projector lamp will go off and the STANDBY ON indicator begins blinking when the passed time with a proper signal without no signal and
22. ay of the selected item will appear 4 Use the cursor button W 4 Use the cursor buttons A V to operate the item to select the TURN OFF memo When you want to reset the adjustment press the RESET button during the operation Note that the items whose functions are performed simultaneously with operating ex LANGUAGE WHISPER H PHASE etc are not reset memo When you want to return to the previous display press the A or ESC button 5 Press the MENU button again to close the menu 5 Press the MENU button display and complete this operation memo Even if you don t do anything the menu will automatically disappear after a few seconds Multifunctional Settings continued PICTURE 2 ASPECT With the MAIN menu the items shown in the table below can be AUTO MIRROR SCREEN LANGUAGE performed Perform each operation in accordance with the OPTION Language instructions in the table below NETWORK BRIGHT Adjust the brightness using the 4 Y buttons Light Dark CONTRAST Adjust the contrast using the Y buttons Strong Weak Select an aspect ratio using the Y buttons E For an RGB signal NORMAL 4 3 16 9 REAL ASPECT The NORMAL keeps the original aspect ratio of the input signal E For a video signal no signal 4 3 16 9 SMALL REAL memo For a HDTV signal of 11251 1080i or 750p 720p only the 16 9 and REAL can be selected REAL cannot be selected when there is no
23. compatible Plug and Play may not work properly if any other type of connection is attempted e Please use the standard drivers in your computer as this projector is a Plug and Play monitor e The dve8so flex s M1 D is compatible with HDCP High bandwiadth Digital Content Protection and therefore capable od displaying video from HDCP compatible DVD players et al However if the HDCP standards are modified the dve880 flex s M1 D might not be able to display video from HDCP compatible developed in conformance to such modified HDCP standards Setting Up continued Please refer to the following for example for connecting your devices See the rear of the projector You can see the ports Examples of connection with a computer p Projector RGB out RGB cable _ RGB Audio out Stereo Mini cable AUDIO IN 2 ooo0oo0oo0o r ooo0oo0o0o E ET 7 i i o essa L RS 232C port RS 232C cable CONTROL SS a Network port CAT 5 cable NETWORK E if using a M1 D input to mouse control OOOOOOoOo I p000000000 C1 oOoooooo0o0o0o0 Doooooooooo OOOoOoooooO C1 OOOoOoOoOoo l DVI port M1 D as E USB port M1 D cable Audio out Stereo Mini cable AUDIO IN 1 E if using a BNC input R Cr Pr G Y B Ce Pa H V R Cr Pr GN 20 0 0 0 0 B Ce Ps RGB out H Ov e _5 Audio out Stereo Mini cable AUDIO IN 1 10 Setting Up continued Examples of connection with
24. cooled down please make confirmation of the following items and then turn the power on again e Is there blockage of the air passage aperture e Is the air filter dirty e Does the peripheral temperature exceed 35 C If the same indication is displayed after the treatment please contact your dealer or service company There is a possibility that the interior portion has become overcooled Please use the unit within the usage temperature parameters 0 C to 35 C After the treatment resent the power to ON If the same indication is displayed after the treatment please contact your dealer or service company It is time to clean the air filter or there is no filter cover Please immediately turn the power OFF and clean or change the air filter by referring to the section Air Filter After cleaning or changed the lamp please be sure to reset the filter timer After the treatment resent the power to ON Troubleshooting continued Phenomena That May Easily Be Mistaken For Machine Defects Before requesting repair please check in accordance with the following chart If the situation cannot be corrected please contact your dealer or service company NOTE o Although bright spots or dark spots may appear on the screen this is a unique characteristic of liquid crystal displays and such do not constitute or imply a machine defect Cases not involving a machine defect pela Power does not come on Neither
25. deo signal The vertical position and horizontal position will be automatically adjusted E For a component video signal The aspect ratio will be automatically selected The clock phase will be automatically adjusted 17 Operating continued Adjusting The Picture Position memo This function is not available for M1 D signals 4 Press the POSITION button As illustrated on the right a dialog will appear on the screen to aid you in adjusting the position A POSITION lt 4 v Cursor buttons 2 Use the cursor buttons amp W 4 P to adjust the position POSITION memo When you want to initialize the position press button the RESET button during adjustment Press the POSITION button again to close the 3 dialog and complete this operation memo Even if you don t do anything the dialog will automatically disappear after a few seconds Correcting The Keystone Distortion Press the KEYSTONE button 1 As illustrated on the right a dialog KEYSTONE will appear on the screen to aid you p gt in correcting the keystone RESET button distortion Cursor buttons Use the cursor buttons 4 P to 2 select the direction of distortion to correct or 3 Use the cursor buttons A V to correct the distortion KEYSTONE button Press the KEYSTONE button again to close the A dialog and complete this operation memo Even if you don t do anything the dialog will automatically disappear after a few seconds memo
26. down it lf the air filter needs to be replaced contact your dealer to prepare a new air filter Tell the dealer your air filter type Insert the cleaned air filter or a new air filter and replace the filter cover Hold the release button of the air filter while Turn on the projector power and reset the filter timer pulling out it 1 While the projector running press the MENU button to open the menu 2 Choose the OPTION on the menu using the A Y button then press the button or ENTER button 3 Choose the FILTER TIME using the A Y button then press the gt button or RESET button 4 Choose the RESET using the A button memo Incorrectly resetting of the filter timer resetting without replacement or neglect of resetting after replacement will result in incorrect message functions 39 40 Caring For The Inside Of The Projector In order to ensure the safe use of your projector please have it cleaned and inspected by your local dealer about once every year 1 Caring For The Lens Turn off the projector and unplug the power cord Lightly wipe the lens with a commercially available lens cleaning wipe Do not touch 2 the lens directly with your hand Caring For The Cabinet And Remote Control wea Turn off the projector and unplug the power cord 2 Wipe lightly with gauze or a soft cloth memo If soiling is severe dip soft cloth in water or a neutral cl
27. e Aspect button to toggle between the modes for aspect ratio ASPECT button E For an RGB signal NORMAL gt 4 3 16 9 REAL memo NORMAL keeps the original aspect ratio of the input signal E For a video signal no signal 4 3 gt 16 9 gt SMALL gt REAL memo For a HDTV signal of 11251 1080i or 750p 720p only 16 9 and REAL can be selected REAL cannot be selected when there is no input signal Using The Automatic Adjustment Feature memo The automatic adjustment operation requires approximately 10 seconds Also please note that it may not function correctly with some input Press the AUTO button 1 m For an RGB signal The Vertical position the horizontal position the clock phase and horizontal size will be automatically adjusted And the aspect ratio will be automatically selected memo Make sure that the application window Is set to its maximum size prior to attempting to use this feature Dark pictures may still be incorrectly adjusted Use a bright screen when adjusting AUTO button E For a video signal or s video signal The signal type mode best suited for the respective input signal will be selected automatically This function is available only when the AUTO is selected to the item VIDEO of the INPUT menu For a component video signal the Signal type is identified automatically independently of this function E For a video signal s video signal or component vi
28. eaner dilute in water and wipe lightly after wringing well Then wipe lightly with a soft dry cloth Troublesnooti Related Messages When the unit s power is on messages such as those shown below may be displayed When any such message is displayed on the screen please respond as described below If the same message is displayed after the treatment or if a message other than the following appears please contact your dealer or service company memo Although these messages will be automatically disappeared around several minutes it will be reappeared every time the power is turned on s CHANGE THE LAMP The time the lamp timer has counted is approaching 2000 hours AFTER REPLACING LAMP iia ay te ue and a i eat seen is RESET THE LAMP TIMER recommended After you have change the lamp please be sure to reset the lamp timer CHANGE THE LAMP The time the lamp timer has counted Is approaching 2000 hours so a lamp change within hours is AFTER REPLACING LAMP faded oak er ee r RESET THE LAMP TIMER en lamp usage reaches ours the power wi automatically be turned off THE POWER WILL TURN OFF Please change the lamp by referring to the section Lamp a After you have changed the lamp please be sure to reset the AFTER hr lamp timer x CHANGE THE LAMP As the time the lamp timer has counted has reached AFTER REPLACING LAMP ate the power will soon be automatically eee a i Please immediately turn the power off
29. ector vents or get it in your eyes or mouth power outlet e Before replacing the lamp make sure the power switch is off and the power cable is not plugged in then wait at least 45 minutes for the lamp to cool sufficiently Handling the lamp while hot can cause burns as well as damaging the lamp e Do not open the lamp cover while the projector is suspended from above This is dangerous since if the lamp s bulb has broken the shards will fall out when the cover is opened In addition working in high D places is dangerous so ask your local dealer to have the lamp replaced even if the bulb is not broken e Do not use the projector with the lamp cover removed At the lamp replacing make sure that the screws are screwed in firmly Loose screws could result in damage or injury e Use only the lamp of the specified tyoe ZU0212044010 DT00601 e f the lamp breaks soon after the first time it is used It is possible that there are electrical problems elsewhere besides the lamp If this happens contact your local dealer or a service representative e Handle with care jolting or scratching could cause the lamp bulb to Q burst during use e f the indicators or a message prompts you to replace the lamp see the section Related Messages and Regarding the indicator Lamps replace the lamp as soon as possible Using the lamp for long periods of time or past the replacement date could cause it to burst Do not use old used la
30. f the arrow indicated in the remote it back into place control Remote Control continued Operating The Remote Control NOTE e Replace the batteries whenever the remote control starts to malfunction e When strong light such as direct sunlight or light from an extremely close range such as from an inverter fluorescent lamp hits the projector s remote sensor the remote control may cease to function Adjust the direction of the projector to keep light from directly hitting the projector s remote sensor e The remote control works with the reS projector s remote sensor f e Front remote sensor is 3 meters with a 60 N degree range 30 degrees to the left and WW pA Le right of a remote sensor Rear remote sensor is 3 meters with a 40 degree range 20 degrees to the left and EE AE right of a remote sensor REE REEE e Also a remote signal reflected in the screen etc may be available If it is difficult to send a remote signal to the sensor directly please try e Since the remote control uses infrared light to send signals to the projector Class1 LED be sure to use the remote control in an area free from obstacles that could block the remote control s output signal to the projector ea 20 degrees memo You can use the remote control as a wired remote control by connecting the REMOTE CONTROL ports of the main unit and remote control via an audio cable 3 5 dia stereo mini cable with plugs Using The Remo
31. ings are not properly Adjust the focus using the focus buttons and or H PHASE using the menu function The lens is dirty or misty Clean the lens by referring to the section Caring For The Lens The INPUT dial is set between the click points Turn the INPUT dial and set it at a click point Reference pages 4 15 23 19 O 23 aE Warranty And AT If a problem occurs with the equipment first refer to the Troubleshooting and run through the suggested checks If this does not resolve the problem please contact your dealer or service company They will tell you what warranty condition is applied AC100 120V 5 2A AC220 240V 2 2A 470W O 35 C Operating 420 W x 150 H x 310 D mm Not including protruding parts e Please refer to the figure of the section TECHNICAL of the end of this manual Weight mass RGB input ports RGB output port RGB RGB OUT M1 D BNC R G B H V Audio output port AUDIO OUT Video input ports VIDEO IN Control port S VIDEO CONTROL COMPONENT CR PR CB PB Y Other ports NETWORK Audio input ports REMOTE CONTROL AUDIO IN 1 DC OUT AUDIO IN 2 AUDIO IN R L ZU0212044010 DT00601 EKO212011140 NJ08081 e Please consult your dealer 47
32. input signal Select the NORMAL or the WHISPER using the 4 Y buttons NORMAL amp WHISPER When the WHISPER is selected acoustic noise and screen brightness are reduced Select a mirror status using the 4 Y buttons NORMAL H INVERT V INVERT H amp V INVERT MIRROR ex RA EJ Oe Select a menu language using the Y buttons ENGLISH amp FRANCAIS lt DEUTSCH amp ESPANOL ITALIANO NORSK NEDERLANDS amp PORTUGUES e H55 P30 e HHA ota amp SVENSKA PYCCKUN lt SUOMI amp POLSKI amp T RK E Select the EXECUTE using the button to reset the MAIN menu items RESET EXECUTE amp CANCEL The items of the MAIN menu are collectively returned to the initial setting Note that the items WHISPER and LANGUAGE are not reset 23 Multifunctional Settings continued PICTURE 1 Menu ona INPUT COLOR BAL B With the PICTURE 1 menu the items shown in the table below can AUTO SHARPNESS REEN COLOR be performed Perform each operation in accordance with the OPTION TINT i NETWORK MY MEMORY instructions in the table below 7 Select a gamma mode using the 4 Y buttons NORMAL amp CINEMA amp DYNAMIC amp CUSTOM Selecting the CUSTOM and then pressing the P or the ENTER button calls the CUSTOM menu CUSTOM Menu Select an item using the 4 Y buttons and press the erie Sire a gt or the ENTER button to perform each function niles GAMMA COLOR TEMPS RS GO
33. liminate flicker using the Y buttons Right Left memo This item can be selected only at a RGB signal or a component video signal other than a COMPONENT port input of 5251 4801 6251 5761 SCART RGB memo When this adjustment is excessive the picture may not be displayed correctly In such a case please reset the adjustment pressing the RESET button during this operation Adjust the over scan ratio using the 4 Y buttons Small Large OVER SCAN memo This item can be selected only at a video signal memo When this adjustment is too large certain degradation may appear at the frame area of the picture In such a case please adjust small Select the EXECUTE using the button to reset the PICTURE 2 menu items RESET EXECUTE amp CANCEL The items of the PICTURE 2 menu are collectively returned to the initial setting Note that the item H PHASE is not reset Adjust the horizontal size using the 4 Y buttons Large Small memo This item can be selected only at a RGB signal Multifunctional Settings continued MAIN COLOR SPACE AUTO PICTURE 1 COMPONENT COMPONENT PICTURE 2 VIDEO AUTO INPUT 3D YCS TURN OFF With the INPUT menu the items shown in the table below can be AUTO VIDEO NR Low performed Perform each operation in accordance with the oe toe E instructions in the table below SE DOK EEE INPUT RGE E a a Select a color space mode using the Y buttons AUTO RGB amp SMPTE240
34. ls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure AVOID EXPOSURE LASER RADIATION IS EMITTED FROM THIS APERTURE CAUTION LASER RADIATION al DO NOT STARE INTO BEAM WAVE LENGTH eio eaonm JAX OUTPU aires 2 reco A ane i eee ee 9522L H mm JIS C 6802 1998 HRA 1 0mW R 640 66Onm MODEL H IRC4 L P HEDTEAEGUTE LD P HEAITMAIFIAUTE FICHE DRECE S56 INTERLINK ELECTRONICS MANUFACTURER MANUFACTURED JANUARY 2003 B INTERLINK K 1 10 7 HIGASHKANDA CHIYODA KU TOKYO JAPAN MADE IN CHINA DN This remote control has a laser pointer in place of a finger or rod The laser beam works and the LASER INDICATOR lights while the LASER button is pressed Loading Batteries N CAUTION About the battery Keep a battery away from children and pets Use only the battery specified two AA batteries Do not mix new battery with used one Make sure the plus and minus terminals are correctly aligned when loading the battery as indicated in the remote control e Dispose of batteries in accord with environmental laws Remove the battery Insert the batteries Close the battery 1 cover 2 Align and insert the 3 cover Slide back and two AA batteries Replace the battery remove the battery according to their plus cover in the direction cover in the direction minus terminals as of the arrow and snap o
35. mena That May Easily Be Mistaken For Machine Defects 45 Warranty And After Service 47 Specifications Bracers eee ete ee 66 wie eases ete ses 47 TECHNICAL Projector Front Right Projector Rear Left Elevator button Elevator foot Remote sensor Lens cap Lens The picture is projected from here Filter cover An air filter is inside OSes RGB port M1 D port BNC port AUDIO IN 1 port AUDIO IN 2 port CONTROL port NETWORK port AUDIO IN R L port VIDEO IN port S VIDEO port COMPONENT port RGB OUT port AUDIO OUT port REMOTE CONTROL port DC OUT port AC Inlet Power switch Control buttons see the following page Part Names continued Control Buttons is of Co LENS SHIFT FOCUS ZOOM COMPONENTO S VIDEO Y Control Panel on the Projector Remote Control STANDBY ON button 0 IN 4 LENS SHIFT buttons 1 STANDBY ON VIDEO e 13 SEARCH button mn SIG ZOOM buttons 14 ss B FOCUS buttons KEYSTONE button 10 MENU button 19 PREVIOUS RESET button ENTER button 16 4D Mouse left button ESG MENU u 29 POSITION RESET uTO 31 MAGNFY PinP VOLUME Rear FREEZE MUTE 3 KEYSTONE SS D Cursor buttons NA 123 A V lt gt ID CHANGE E Keyboard 15 Arrow keys fI B1 l4 B2I Remote Control 9 BOSeeseesseeQodogs SSeseseese O SSSSSES 36 STANDBY ON button and STANDBY
36. mps this is a cause of breakage 38 Lamp continued Replacing The Lamp If the indicators or a message prompts you to replace the lamp replace the lamp as soon as possible 1 2 Turn off the projector and unplug the power cord Allow the lamp bulb to cool for at least 45 minutes Contact your dealer to prepare a new lamp Tell the dealer your lamp type number If the projector is mounted on the ceiling or if the lamp has broken also ask the dealer to replace the lamp In the case of replacement by yourself 3 After making sure that the projector has cooled Lamp cover adequately slide the knob of a lamp cover lock as knob shown in the Figure Then one side of the lamp cover is raised Pull up the lamp cover and remove it as shown in the Figure Lamp cover Unscrew the 3 screws and slowly pull out the lamp by the handle Be careful not to touch the inside of the lamp case Insert the new lamp and tighten the 3 screws firmly to lock it in place Interlocking the 2 tabs of the lamp cover to the projector put the lamp cover on the projector Then push the point of the lamp cover to fix it as shown in the Figure Make sure that the lamp cover does t come up Turn on the projector and reset the lamp timer 1 While the projector running press the MENU button to open the menu 2 Choose the OPTION on the menu using the A W button then press the gt button or ENTER button 3 Ch
37. n this function performs the setting of the item VIDEO NR of this INPUT menu is not effective Select a noise reduction level using the 4 Y buttons HIGH MIDDLE LOW The noise on screen is reduced according to the selected level VIDEO NR memo This item performs only at a video signal from the VIDEO port or the S VIDEO port At a video signal of NTSC3 58 this function performs only when the TURN OFF is selected to the item 3D YSC of this INPUT menu memo When this adjustment is excessive certain degradation may appear on the picture This table is continued to the following page 2 28 Multifunctional Settings continued INPUT Menu continued a ae rr Select a signal input port for the child window using the A Y buttons VIDEO amp S VIDEO memo About the child window please refer to the section Displaying the Child Window Select the display position of the child window using the 4 Y buttons gt S Ie La P IN P POSIT memo About the child window please refer to the section Displaying the Child Window Select a signal input port to display just when the projector is turned on using POWERUP the 4 Y buttons INPUT LAST INPUT amp M1 D amp RGB amp BNC amp COMPONENT S VIDEO VIDEO Selecting the LAST INPUT selects the port that was used at the last time Pressing the or the ENTER button displays the INPUT INFORMATION menu The INPUT INFORMA
38. of the BLANK screen using the A Y buttons MyScreen ORIGINAL BLUE WHITE BLACK The BLANK screen is the screen which is displayed by pressing the BLANK button The MyScreen is the screen you can register a desired screen and the ORIGINAL is the existing standard screen The BLUE the WHITE and the BLACK are the non pattered plain screens in each color memo To avoid remaining as an afterimage the MyScreen and the ORIGINAL screens will change to the BLACK screen after several minutes memo For the MyScreen please refer to the item MyScreen in this table Select a type of the START UP screen using the A Y buttons MyScreen ORIGINAL lt TURN OFF The START UP screen is the screen which is displayed by detecting no signal or an unsuitable signal The MyScreen is the screen you can register a desired screen and the ORIGINAL is the existing standard screen When the TURN OFF is selected the BLACK is used memo To avoid remaining as an afterimage the MyScreen and the ORIGINAL screens will change to the BLANK after several minutes If also the BLANK screen is the MyScreen or the ORIGINAL it will change to the BLACK screen memo About the MyScreen please refer to the item MyScreen in this table About the BLUE BLACK and BLANK screens please refer to the item BLANK in this table Pressing the or the ENTER button starts the MyScreen registration Please see the flow chart on the following page memo Images
39. onds 21 22 Using The Menu Functions This projector has the following menus MAIN PICTURE 1 PICTURE 2 INPUT AUTO SCREEN OPTION and NETWORK Each of these menus is operated using the same methods The basic operations of these menus are as follows ex Turning off the built in speaker 1 Press the MENU button C u rsor J BRIGHT 0 PICTURE 1 CONTRAST 0 b PICTURE 2 ASPECT 4 3 u tto n S INPUT WHISPER NORMAL AUTO MIRROR NORMAL SCREEN LANGUAGE ENGLISH OPTION Language NETWORK RESET r SELECT MENU button 2 Select the OPTION using the W button then press the button VAN VOLUME ee Cor VOLUME e PICTURE 1 SPEAKER TURN ON PICTURE 1 SPEAKER Em ON PICTURE 2 IR REMOTE PICTURE 2 IR REMOTE re PUT IR a ID ALL o n ea ID ALL AUTO LAMP 1234h TIME 1234 h SCREEN as MHE 4321 h E FILTER TIME 4321 h oe K OETON SERVICE OPTION SERVICE r ae ee RESET 3 Select the SPEAKER using the W button then ENTER press the gt button Press the MENU button The menu will appear on the screen 9 Use the cursor buttons A V to select a menu then press the P or the ENTER button to progress The display of the selected menu will appear RESET button ESC button 3 Use the cursor buttons A V to select an item then press the P or the ENTER button to button p rog rosa IR REMOTE ID ALL ad Gea LAMP TIME 1234 h FILTER TIME 4321 h The operation displ
40. oose the LAMP TIME using the A button then press the gt button or RESET button 4 Choose the RESET using the button memo When the lamp has been replaced after the message of THE POWER WILL TURN OFF AFTER Ohr is displayed complete this operation within 10 minutes of switching power on memo Incorrectly resetting of the lamp timer resetting without replacement or neglect of resetting after replacement will result in incorrect message functions Caring For The Air Filter Cleaning the air filter every 100 hours using the FILTER MESSAGE function is recommended If the indicators or a message prompts you to clean the air filter clean the air filter as soon as possible Please check and clean the air filter periodically even if there is no message If the soiling will not come off the air filter or it becomes damaged then it needs to be replaced Please replace the air filter as soon as possible memo When you replace the lamp please replace also the air filter 1 2 Turn off the projector and unplug the power cord Allow the lamp bulb to cool for at least 45 minutes After making sure that the projector has cooled adequately remove the filter cover and air filter Apply a vacuum cleaner to the top of the filter cover and Hold the release the air filter to clean buttons of the filter If the soiling will not come off the air filter or it becomes cover while pulling damaged it needs to be replaced
41. or cables that have a core only at one end connect the core to the projector e Secure the screws on the connectors and tighten e Whenever attempting to connect a laptop computer to the projector be sure to activate the laptop s RGB external image output set the laptop to CRT display or to simultaneous LCD and CRT display For details on how this is done please refer to the instruction manual of the corresponding laptop computer NOTE o Some computers may have multiple display screen modes Use of some of these modes may not be compatible with this projector e For some RGB input modes the optional Mac adapter is necessary e When the image resolution is changed on a computer depending on an input automatic adjust function may take some time and may not be completed In this case you may not be able to see a check box to select Yes No for the new resolution on Windows Then the resolution will go back to the original It might be recommended to use other CRT or TFT monitors to change the resolution NOTE Plug and Play Capability e Plug and Play is a system incorporated in the computer its operating system and peripheral equipment i e display devices e This projector is compatible with VESA DDC 2B Plug and Play can be achieved by connecting this projector to computers that are VESA DDC display data channel compatible e Please take advantage of this function by connecting the accessory RGB cable to the RGB port DDC 2B
42. projector has sufficiently cooled down please make confirmation of the attachment state of the lamp and lamp cover and then turn the power on again STANDBY O LAMP TEMP aus Lighting Turned Turned The projector is in a standby state in Orange off off Please refer to the section Power On Off Blinking Turned Turned The projector is warming up in Green off off Please wait Lighting Turned Turned The projector is in an on state in Green off off Ordinary operations may be performed Blinking Turned Turned The projector is cooling down in Orange off off Please wait The projector is cooling down A certain error has been detected Please wait until the STANDBY ON indicator finishes blink and then perform the proper response measure using the item descriptions below as reference Blinking discre discre in Red tionary tionary The lamp does not light and there is a possibility that interior portion has become heated Please turn the power off and allow the unit to cool down at least 20 minutes After the projector has sufficiently cooled down please make confirmation of the following items and then turn the power on again e Is there blockage of the air passage aperture e Is the air filter dirty e Does the peripheral temperature exceed 35 C If the same indication is displayed after the treatment please change the lamp by referring to the section Lamp Lighting Lighting Turned in Red in Red off
43. rating Selecting An Input Signal 1 2 Use the ZOOM buttons to adjust the screen size 3 Use the FOCUS buttons to adjust the focus Select an input signal E Using the INPUT dial SEARCH button Turn the INPUT dial of the projector Turning the dial cycles through the input ports as shown below Select the signal you wish to project YSTONE M1 D lt gt RGB lt gt BNC VIDEO lt gt S VIDEO lt gt COMPONENT E Using SEARCH button Press the SEARCH button of the projector or the remote control Pressing the button automatically cycles through input ports and displays the picture of retrieved signal memo If no signal is found or the projector is unstable to find an input signal at any of its ports it will turn to the state it was in prior to the search M1 D gt RGB gt BNC VIDEO lt S VIDEO lt COMPONENT E Using RGB button Press the RGB button of the remote control Pressing the button toggles between the RGB ports as shown below Select the signal you wish to project SEARCH button M1 D RGB BNC E Using VIDEO button Press the VIDEO button of the remote control pone PA Pressing the button toggles between the VIDEO ports as shown below Select the signal you wish to project COMPONENT S VIDEO VIDEO FOCUS ZOOM buttons buttons Operating continued Selecting The Aspect Ratio 4 Press th
44. reen and the screen will lt freeze at the current image l Press the FREEZE button again to restore the 2 screen to normal The icon II will change to the icon And after a couple of seconds the dialog will be closed and the screen will be restored to normal FREEZE button memo The freezing feature will automatically finish if a remote control s button that changes some display state ex blanking the screen displaying a dialog or a menu adjusting the picture changing the input signal is pressed or a button of projector is pressed NOTE effihe projector continues projecting the same image for a long time i e you forget to exit FREEZE mode the image might possibly remain as an afterimage Do not leave the projector in FREEZE mode for too long Using The Magnify Feature Press the MAGNIFY 1 button As illustrated on the right a dialog will appear on the screen to aid you in magnifying the picture Cursor buttons 9 Press the POSITION button then use the cursor buttons amp W 4 P to select the area to zoom POSITION 3 Press the POSITION button again to finalize the button zoom area Use the cursor buttons A V to adjust the zoom PA 4 buttons level 5 Press the MAGNIFY button again to close the dialog and complete this operation memo The magnify feature will automatically finish if the automatic adjustment is execute or the aspect the signal type mode of video or the signal input
45. resets the count of the filter timer to O FILTER TIME memo Perform this function only when you have cleaned or replaced the air filter The filter timer counts the used time of the air filter after cleaning or replacement to display the messages about the air filter Incorrect performing Causes incorrect operation of the messages memo About caring for the air filter please refer to the section Air Filter This table is continued to the following page 33 Multifunctional Settings continued OPTION Menu continued Description Pressing the or the ENTER button calls the SERVICE menu SERVICE Menu IS AEST EMBL Select an item using the 4 Y buttons and press the P or the ENTER button to per form each function cst FANSPEED AUTO ADJUST amp LENS TYPE LENS LOCK amp GHOST amp FILTER MESSAGE TO Select the fan speed level using the Y buttons HIGH amp NORMAL The HIGH ups rotation speeds of fans though Please use this function in using a projector at highlands etc memo Note that the projector is noisier when the HIGH is selected Select the ENABLE or the DISABLE using the A Y buttons ENABLE amp DISABLE When the ENABLE is selected detecting a signal change to a RGB signal performs the automatic adjustment of the vertical position V AUTO POSITION the horizontal position H POSITION the clock phase ADJUST H PHASE and the horizontal size H SIZE Depending on conditions such
46. s After the projector has sufficiently cooled FAILURE TO CLEAN MAY down please make confirmation of the following items and RESULT IN DAMAGE TO THE _ then turn the power on again PROJECTOR e Is there blockage of the air passage aperture e Is the air filter dirty SEE MANUAL FURTHER INFO e Does the peripheral temperature exceed 35 C e Is the filter cover in place There is no input signal ba ede O TESLED Please confirm the signal input connection and the status of the signal source The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit Please confirm the specs for this unit or the signal source Specs SYNC IS OUT OF RANGE ON fH lahelated 4 2 Z Troubleshooting continued Regarding The Indicator Lamps Lighting and flashing of the STANDBY ON indicator the LAMP indicator and the TEMP indicator have the meanings as described in the table below Please respond in accordance with the instructions within the table If the same indication is displayed after the treatment or if an indication other than the following is displayed please contact your dealer or service company NOTE o When the interior portion has become overheated for safety purposes the power source is automatically turned off and the indicator lamps may also be turned off In such a case press the O OFF side of the main power switch and wait at least 45 minutes After the
47. s 4 numbered memories for adjustment data Performing the SAVE1 SAVE2 SAVES or SAVE4 puts the current adjustment data on the memory whose number corresponds with the command s number The current adjustment data of the items BRIGHT and CONTRAST in the MAIN menu and the items in the PICTURE 1 menu is stored Performing the LOAD1 LOAD2 LOAD3 or LOAD4 loads the data on the memory whose number corresponds with the command s number and adjusts the picture automatically depending on the data Select the EXECUTE using the button to reset the PICTURE 1 menu items EXECUTE CANCEL The items of the PICTURE 1 menu are collectively returned to the initial setting Note that the items MY MEMORY and GAMMA of the CUSTOM menu under the item GAMMA are not reset ZO 26 Multifunctional Settings continued PICTURE 2 Menu EME PICTURE 2 H PHASE INPUT H SIZE With the PICTURE 2 menu the items shown in the table below can AUTO OVER SCAN be performed Perform each operation in accordance with the e a instructions in the table below akuna memo This menu cannot be selected at a M1 D signal e S re Adjust the vertical position using the Y buttons V POSITION Up amp Down memo This item cannot be selected for a M1 D signal Adjust the horizontal position using the Y buttons H POSITION Left Right memo This item cannot be selected for a M1 D signal Adjust the horizontal phase to e
48. state is changed Operating continued Displaying The Child Window memo This feature called PinP Picture in Picture is available only when a RGB signal is selected to main screen And this feature does not work when UXGA 1600 x 1200 or higher signal is input Press the PinP button The child window with a picture of a video signal will appear 9 Press the PinP button again to change the size of the child window or close the window Small child window Large child window M PinP button No child window memo You can select the video signal to display in the child window and the position of the child window Please refer to the items P INP INPUT and P INP POSIT of the table of the section INPUT Menu memo This feature is available only when the child window is on the screen 4 When the child window is on the VOLUME screen press the VOLUME button RGB P Video As illustrated on the right a dialog A will appear on the screen Cursor Use the cursor buttons d P to buttons select an audio input RGB Audio input for the main screen VOLUME button Video Audio input for the child window memo You also can adjust the volume using the cursor buttons 4 P Please refer to the section Adjusting The Volume 3 Press the VOLUME button again to close the dialog and complete this operation memo Even if you don t do anything the dialog will automatically disappear after a few sec
49. te ID Feature This is the function to properly use when you use two or three same type projectors at the same time This function should be used combining a setup of a projector 4 Set the ID number to the projector beforehand referring to the item IR REMOTE ID of the section OPTION Menu memo When the ALL is selected to the item IR REMOTE ID of the OPTION menu the projector is controlled by a remote control irrespective of the position of the ID CHANGE switch ID CHANGE Switch 2 Slide the knob of the switch into the position of the ID number of the projector you want to control 13 14 Remote Control continued Using The Mouse Keyboard Control Function Using the USB control feature you can use the remote control as a simplified mouse or keyboard of the computer Connect the M1 D port of the projector to the computer via the M1 D cable Then functions illustrated below will be enabled memo The USB control can be used with Windows 95 OSR 2 1 or higher It may not be possible to use the remote control depending on the computer s configurations and mouse drivers 4D Mouse left button memo The function can be used only for the functions illustrated on the right 4D Mouse move pointer Keyboard memo The projector would be enumerated as a Arrow keys f mouse and a keyboard of HID Human Interface Device class devices after connecting cable 4D Mouse right button Keyboard key
50. to top page 6 Click REBOOT to complete this operation Lamp A WARNING A A HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE The projector uses a high pressure mercury glass lamp The lamp can break with a loud bang or burn out if jolted or scratched handled while hot or worn over time Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them In addition when the bulb bursts it is possible for shards of glass to fly into the lamp housing and for gas containing mercury to escape from the projector s vent holes About disposal of a lamp This product contains a mercury lamp do not put in trash Dispose of in accord with environmental laws For lamp recycling go to www lamprecycle org in the US For product disposal contact your local government agency or www eiae org in the US or www epsc ca in Canada For more information call your dealer e f the lamp should break it will make a loud bang when it does unplug the power cord from the outlet and make sure to request a replacement lamp from your local dealer Note that shards of glass could damage the projector s internals or cause injury during handling so please do not try g to clean the projector or replace the lamp yourself e f the lamp should break it will make a loud bang when it does ventilate Disconnect the the room well and make sure not to breathe the gas that comes out of plug from the the proj
51. ures are displayed Video screen The FREEZE function is working 2 display freezes Press the FREEZE button to restore the screen to normal Colors have a faded out appearance or Color tone is poor Pictures appear dark Pictures appear blurry Input signal changes with no operation The signal cables are not correctly connected Correctly connect the connection cables The volume is adjusted to an extremely low level Adjust the VOLUME to a higher level The sound is muted Press the MUTE button to restore the sound The audio input is not correctly selected when the child window is displayed Correctly select the audio input The lens cap is attached Remove the lens cap The signal cables are not correctly connected Correctly connect the connection cables The brightness is adjusted to an extremely low level Adjust the BRIGHT to a higher level using the menu function The screen is blanked Press the BLANK button to return to the input signal screen Color settings are not correctly adjusted Perform picture adjustments by changing the COLOR BAL R COLOR BAL G COLOR BAL B COLOR and or TINT settings using the menu functions The brightness and or contrast are adjusted to an extremely low level Adjust the BRIGHT and or CONTRAST settings to a higher level using the menu function The lamp is approaching the end of its product lifetime Replace the lamp Either the focus and or horizontal phase sett
52. urned to the initial setting How to register your picture as the MyScreen MyScreen is pointed on the SCREEN menu Press the gt button T Do you start capturing this picture The MyScreen menu appears Do you capture the picture from the current screen NO Press the ESC RESET button If the ESC RESET button is pressed YES Press the ENTER button The picture freeze and the frame for capturing appears Move the frame to the position of the picture which you want to use using A V 4 P buttons and press the ENTER button to register meno The frame may not be able to be moved for some input signals My Screen Xy mm o Registering It takes about 1 minute to register Just when the picture registration is completed the registered screen and MyScreen registration is ished the message of the right is displayed for a few seconds If the picture registration failed Eo a the message of the right is displayed for a few seconds a AAE 32 Multifunctional Settings continued MAIN O OPTION Menu ee a PICTURE 2 IR REMOTE 102 03 M With the OPTION menu the items shown in the table below can be ura EO San performed Perform each operation in accordance with the ae a instructions in the table below NETWORK RESET Be ee eee VOLUME Adjust the volume using the A Y buttons High Low Select the TURN ON or the TURN OFF using the A Y buttons T
53. wer eee 15 Turning Off The Power eee 15 Operating ERREEN RE EETA 16 Selecting An Input Signal 16 Selecting The Aspect Ratio 17 Using The Automatic Adjustment Feature eee 17 Adjusting The Picture Position 18 Correcting The Keystone Distortion EEEE 6 OS ear See OS STE 18 Adjusting The Volume esee 19 Muting The Sound aaen a a ara ariin a 19 Temporarily Blanking The Screen de Sve aE a alte er E E A O S 19 Freezing The Screen 00e 20 Using The Magnify Feature 20 Displaying The Child Window 21 Selecting An Audio Input 21 Multifunctional Settings 22 Using The Menu Functions 22 MAIN Menu aye hei dete tes or 2 Wee Bees ws 23 PICTURE 1 Menu Deea ise mordan Be ye 7s 8s 24 PICTURE 2 Menu oO ial E EE E 26 INPUT Menu a iar Rs aaa aa ane aa at ve ce 9 8 27 AUTO Menu jb herbi Baraua aaea a E E 86 29 SCREEN Menu ee ee ee eee es ae 31 OPTION Menu E E E E te Sar ele hace 33 NETWORK Menu ee ee ee ee 35 Network Setting Up 36 Lamp ceeeeeeeeerseererererrerererererees 37 Replacing The Lamp 000e 38 Air Filter E E L E E ee eT E E 39 Caring For The Air Filter 39 Other Care E E E eee E EEE 40 Caring For The Inside Of The Projector ee ORES EENES 40 Caring For The Lens 006e 40 Caring For The Cabinet And Remote Control Cee a ae aa ETE 40 Troubleshooting eTrr rere Tee ee E 41 Related Messages as Sieh aha Sherer evga stele ere 41 Regarding The Indicator Lamps ere ee ee ee A3 Pheno

User`s Manual - Operating Guide

Contents

Download Pdf Manuals

Related Search

Related Contents